Search Documents

By K. K. Kershner

The purpose of this research by the Federal Bureau of Mines was to investigate the recovery of tin from mine-run ores and low-grade concentrates. Over 95 percent of the total tin in such materials was volatilized to tin chlorides at temperatures ranging from 520° to 565° C. Gaseous mixtures of hydrogen and hydrogen chloride were used for reducing cassiterite to stannous oxide and for converting this compound to tin chlorides. The chlorides were swept from the reaction zone of an oscillating kiln by a rapid flow of reactant gases and collected in a condensing system. Losses of tin that occur in current metallurgical processing were prevented. Approximately the same time of treatment was required for minus 35-mesh mine-run ores and low-grade concentrates. In a continuous process, the circulating gases would require some enrichment.

Jan 1, 1961

By R. L. Levens

The Underground Injection Control program was promulgated in 1981 by the U.S. Environmental Protection Agency under the provisions of the Safe Drinking Water Act. Placement of mine waste backfill underground is considered underground injection under the provisions of this program. A major issue is whether mine waste that is regulated as a contaminant source on the surface should be disposed of underground. The U.S. Bureau of Mines conducted research to investigate the impacts of mine waste sandfill on the quality of ground water. Analyses of water samples collected before and after contact with sandfill in a 10-year-old stope, as well as samples of the sandfill itself, were used to ascertain the influence of the sandfill after mine closure and subsequent flooding. Computer models supported the hypothesis that oxidation of pyrite by oxygen, accompanied by dissolution of carbonates, was the predominant reaction controlling the quality of the water being discharged from the stope. Concentrations of metals released as a result of acid production remained near or below detection limits. Metals release after mine flooding is expected to remain low as a result of the buffering by the sandfill and the reduced rate of oxidation.

Jan 1, 2010

By C. P. Hood

"The amount of ash in anthracite coal interests every buyer, and occasionally produces caustic comment, but there is a lack of authentic figures that will take the subject out of the realm of opinion and agitated fancy and. give a true picture of the quality of coal actually delivered. What per cent ash is to be expected when the coal is good, and when have we a right to make serious complaint?During the past summer the Bureau of Mines took 127 samples of 1000 pounds each, representing nearly 30,000 tons of anthracite is dealers' yards in seventeen cities in the State of Massachusetts. There were three objects in view, to discover the average and the variation in amount of ash in anthracite in some easily described area; to demonstrate standard sampling methods, and to learn something about the feasibility of itinerant coal sampling. Massachusetts was selected because its principal cities could be visited in a single season. There also appeared need for demonstration of standard sampling of coal, since a coal quality law had been passed in the State, to be administered by those unfamiliar with coal sampling."

Feb 1, 1924

By J. C. Gerdeen

A new analytical model for the shear stiffness at a joint of the fully-grouted resin roofbolt is developed using the Theory of Elasticity and an analogy to a beam on an elastic foundation, Gerdeen [2]. The model developed in this study treats the elastic foundation modulus of the resin as being composed of both an elastic rock and an elastic resin. All previous attempts have neglected the elasticity of the rock and treated only the resin. A three dimensional finite element model of the bolt-resin-rock system is developed also and comparisons are made between the predictions made by it and the analytical solution. It is found that the agreement between the two representations ranges between 1.2% and 10.5%, with the greater differences being observed for systems of very large or very small bolt diameters and resin annulus thicknesses. Since such configurations are not the rule in practice parameter studies are performed using the analytical solution with the finite element solution being used as a check. For a 0.75 in. bolt, a resin annulus thickness of 0.1375 in., a resin with E = 7 x 105 psi and -1) = 0.210, and a rock of modulus E = 6.8 x 106 psi and V = 0.159 the shear stiffness is found to be 1.220 x 106 lb,/in, from the analytical solution and 1.245 x 106 lb,/in, from the finite element model. Applying the finite element model to the problem of the axial stiffness of the fully-grouted resin roofbolt a value of 6.002 x 106 lb./in. is obtained which proves to be at least 50% higher than any of the now existing analytical predictions.

Jan 1, 1976

By J. Koster

In the western United States occurs deposits of low-grade chromite which, when concentrated, may be reduced to ferrochromiun in electric furnaces that derive energy from dams and hydro plants now in course of construction. Montana ore was chosen for the experiments. A 1-ton sample contained 26 percent Cr203, 17 percent Fed, and 17 percent SiO2, plus other constituents, and the concentrates therefrom assayed 44 -percent Cr203, 23 percent FeO, and 0.79 per cent SiO2, Gravity concentration was found to be the best method. Ferrochromiums are of two grades - high-carbon with 66 to 70 percent chromium and 4-112 to 6 percent carbon and low-carbor with 67 to 72 percent chromium and 0.6 to 2 percent carbon. Both are made in electric furnaces that use anthracite as a reducer and suit-able fluxes. The concentrates mentioned mere smelted under different conditions, and it was concluded that domestic ore could be reduced with anthracite to produce a ferrochromium of S to 10 percent carbon content at yields of 90 percent without retreating the slag. This carbon may be lowered to required proportion with calcium and silicon, but the former requires a great excess and the latter leaves an alloy high in silicon. INTRODUCTION Chromite occurs in several regions of the United States, but the known deposits of this mineral have not been large enough or high grade enough to permit them to compete under normal conditions with imported ores. There are numerous deposits of chrome ore along the West coast. These are generally conceded to be relatively small, although some -were worked during the World War. There are some indications of a revival of interest in California chromites. Montana contains large chromite deposits in Stillwater and Sweetgrass Counties. The utilization of chromite for ferrochromium and. the manufacture of stainless steels is distinctly an electrometallurgical problem; consequently, a study of methods for treatment of chromite might pave the way for the establishment of new electrometallurgical industries in the Western States. This thought is supported by the cheap power that is soon to become available from the western dams. Farther, submarginal domestic chrome deposits might thus be turned into profitable producers.

Jan 1, 1936

By F. Matanzo

This guide considers only nine of the many wire rope terminations used in the mining industry so use of the information presented for terminations not specifically addressed can be done, but with some risk. The nine terminations considered are: Flemish Loop with Steel Sleeve & Thimble, Flemish Loop with Steel Sleeve, Wedge Socket, Swaged Socket, Turn Back Loop with Aluminum Sleeve & Thimble, Thimble Splice with Four Tucks, V-Bolt Clip with Thimble, Zinc Poured Socket, and Epoxy Resin Poured Socket. The guide uses pull test data, axial fatigue test data, and data on sensitivity to poor workmanship, to rank the nine terminations with respect to these performance measures. A selection procedure is suggested and illustrated with an example. Failure data is used to identify the common modes of failure of each termination and so help the inspector direct his attention to the likely location for a failure and describe what he should be looking for. The data on which this guide is based is included so that as new data becomes available, the ranking order can be adjusted accordingly.

Jan 1, 1978

By G. M. Kintz

The data in this circular were taken from publications of the United States Bureau of Mines and published annual reports of the Wyoming State Inspector of Coal Mines. The tables included are complete only' with regard to major disasters; the Bureau of Mines considers a major disaster one in which 5 or more men are killed. However, minor disasters and gas ignitions recorded in these publications are included. It is known that a number of gas ignitions have occurred of which no record is available. This is one of a series of papers by the Bureau of Mines giving by States available data regarding coal-mine explosions. This information is published in condensed form in the belief that it may be of vale to mine operators in preventing future coal-mine explosions.

Jan 1, 1934

By John P. Coughlin

Software techniques developed by the Bureau of Mines Denver Research Center for real-time microseismic data analysis are presented. These techniques focus on the simple acquisition of P-wave arrival times and their use in event location. The paper discusses in detail software techniques to separate microseismic events from mining noise such as drilling and from very large events such as rock bursts. Incorporation of these techniques has enhanced the reliability and accuracy of computer-based monitoring of microseismic activity in ongoing research by the Bureau.

Jan 1, 1982

By Edward D. Thimons

The Bureau of Mines has developed a damage-resistant brattice, intended for use as a stopping in locations where blast damage to stoppings is a problem, the roof is relatively flat, and the differential pressure across the stopping is not high. Damage-resistant brattices consist of a series of vertically hung brattice panels joined to each other by Velcro connections that improve the airtightness of the brattice. When the brattice is subjected to strong blast forces, the Velcro connections peel apart, allowing the panels to open without incurring damage. The Velcro connections can then be resealed in a matter of minutes. A preliminary test in the Bureau's Safety Research Mine and subsequent long-term testing at the White Pine copper mine in Michigan and the Retsof salt mine in New York show that damage-resistant brattices withstand blasting better than conventional stoppings, while still performing as efficient air barriers when the Velcro connections are sealed.

Jan 1, 1978

By Charles L. Kimbell

On the basis of world production data alone, 1985 appears to have been a year in which the world's mineral industry took another step upward in its recovery from the very poor years of 1981, 1982, and early 1983. Despite a drop in the output of crude oil, which was the single most significant crude mineral product from the viewpoint of value, the estimated value of world crude mineral production advanced by 3.4% to about $1,054 billion constant 1983 dollars, with output increases logged for nearly two-thirds of the commodities and forms of commodities for which the U.S. Bureau of Mines calculates a total world output. However, the economic well-being of any industry or group of industries cannot be measured solely in terms of the volume and/or value of its production, and examination of statistics reflecting other aspects of mineral industry performance shows that 1985 was a less than ideal year in many respects. In the case of consumption of mineral commodities, although there were gains registered in diverse sectors such as iron and steel, aluminum, fertilizer materials, solid fuels, and gaseous fuels, there were also proportionally small but notable declines in use among the older major nonferrous metals (copper, lead, tin, and zinc) and in the all-important liquid fuels. In the case of international trade in mineral commodities, although comprehensive data for 1985 were not yet available, there were indications that the value may well have fallen below the estimated 1984 level of $632 billion, although the volume may have increased slightly. This, if true, would be chiefly the result of declining prices of mineral commodities, and indeed, price declines were noted for a number of significant materials in terms of current dollars, and even more would register declines if calculated on the basis of constant dollars, adjusting for inflation.

Jan 1, 1987

By Hamid N. Maleki

Cooperative efforts by the Bureau of Mines and Agapito & Associates, Inc., Grand Junction, CO, achieved the research objective of showing that data from measurements of the rate and change in rate of mine roof movement can be effective in detecting roof instability. Several instruments and techniques have been used to monitor roof movement and to detect imminent roof caves during pillar robbing. Early detection of unstable conditions can provide time either to withdraw personnel and equipment or to allocate supplemental support to prevent injury or down-time. Critical convergence rates were determined both manually and electronically. The detection of critical rate of movement has been shown to be an effective tool in ground control efforts.

Jan 1, 1988

By E. G. King

As low-temperature heat-capacity and entropy data were available for only one sesquisulfide (cerium sesquisulfide), it appeared desirable to augment the information for this class of compounds by measuring the sulfides of antimony and indium. In addition a pressing need existed for data on indium sulfide to supplement vaporization studies in progress in the Department of Mineral Technology, University of California. This Bureau of Mines paper reports low-temperature heat-capacity measurements and entropy evaluations at 298.15° R. of antimony sesquisulfide of stoiehiometric composition (Sb2S3) and of indium sesquisulfide which was somewhat deficient in sulfur (In2S2.93). The data for the latter substance were adjusted to correspond to the stoichiome tric composition (In2S3 ) . Indium sesquisulfide has a lower entropy at 298.15' K, than either antimony sesquisulfide or cerium sesquisulfide, in line with the higher atomic density of the indium compound.

Jan 1, 1962

By Wilton Johnson

Native asphalt was produced by four companies in two States, Texas and Utah. Bituminous limestone, used primarily as a paving material for street and road repair, was produced by one firm. R. L. White Co., Dabney Quarry, Uvalde County, TX. Gilsonite, a solidified hydrocarbon found only in Utah and Colorado, was mined by three firms: American Gilsonite Co., a division of Chevron Resources Co. (a subsidiary of Standard Oil Co. of California); Ziegler Chemical and Mineral Corp.; and Hydrocarbon Mining Co. (a subsidiary of Oberon Oil Inc., a Utah corporation), from properties in Uintah County, UT. Gilsonite is used for a variety of purposes including automobile bodysealer, light-weight aggregate for cement used in oil well drilling, asphaltic building board, protective coverings, anticorrosive paints, and roofing compounds. Gilsonite production in 1985 declined 57% owing primarily to reduced oil well drilling activity. The value per ton was essentially unchanged.

Jan 1, 1987

By Phillip N. Yasnowsky

The thrust of this Bureau of Mines report is to relate the size of automobiles to the price of gasoline, and the use of minerals in automobile manufacture to the size of automobiles. Only one of the many plausible scenarios of public reaction to higher gasoline prices, a switch to economy size automobiles, is developed. No account is taken of other potential impacts such as improvements in public transportation or increased occupancy per vehicle. Furthermore, a gasoline price increase is the only incentive to the greater utilization of economy cars that is considered. A gasoline price increase to $0.60 per gallon would reduce the amount of minerals required to produce the automobiles sold in the United States by an estimated 15 percent. Gasoline prices of $0.80 and $1 per gallon would cause declines in mineral requirements for U.S. automobile sales estimated at 26 percent and 35 percent, respectively.

Jan 1, 1974

By T. T. Campbell

Although secondary recovery of lead and lead-tin alloys has been common practice in the United States during recent years, there is little published in-formation concerning recovery techniques. Available information does not cover metal recovery from wet dross skimmings. This investigation by the Bureau of Mines was undertaken to develop techniques that would allow lead-tin alloys to be recovered from wet dross skimmings containing large amounts of zinc chloride. A process was developed, on a laboratory scale, for recovering lead-tin alloys from wet solder dross skimmings. Straight water leaching, either with or without a second leaching operation carried out with a Na2C03 addition for removing chloride, produced a dross that could be smelted without further treatment. Overall recoveries averaging 92 percent of the metal values in the dross were obtained in the form of lead-tin alloys, which had an average tin content of 16 percent and lead content of 84 percent. The recovered alloy contained less than 0.02 percent zinc, as determined by both chemical and spectrographic analyses.

Jan 1, 1956

By R. Craig Smith

This report presents the software documentation for PREY AL, a prefeasibility mineral property evaluation program developed by the U.S. Bureau of Mines on a Lotus 1-2-3 spreadsheet. It is presented in a step-by-step "user?s manual" format. Appendixes contain the technical assumptions, program default values, and a summary printout detailing capital and operating costs and cash-flow analysis.

Jan 1, 1992

By Lloyd R. Michels, Burke Cartwright, S. F. Ravitz

"INTRODUCTION Frequent attempts have be,made in the electrolysis of molten magnesium chloride to regenerate the electrolyte by allowing the chlorice generated at the anwdo to read with magnesium oxide and carbon within the melt according to the following reactions: (1) MgO + C + CL2 = MgCl2 + CO,(2) 2MgO + C + 2C12 = 2MgC12. + CO2.The principal advantages of such a procedure are that (1) the direct source of magnesium is magnesium oxide rather than the more expensive dehydrated magnesium chloride and (2) it is not necessary to handle or dispose of large quantities of chlorine or hydogen chloride.Grätzll 5/ proposed the use of an MgO carbon feed in a more or,less compact form in the anode compartment, of the cell. In a patent issued to Magall Aktiengecellschaft, 6/ a compact mixture of MgO and carbon is used as the anode itself. Kato 7/ and Backer 8/ add the feed in finely divided form to the surface of the anode compartment. The Bureau of Mines 2/ recently made a pilot-plant investigation of the electrolysis of suspension of MgO and carbon from chloride melts, in which it was found that although,current efficiencies of 60 to 70 percent were obtainable, the formation of sludges containing MgO, carbon, and magnesium seriously interfered with the operation of the cell,"

Apr 1, 1945

By Ronald T. Mayerle

In 1989, the U.S. Bureau of Mines conducted a mineral investigation of the Mallard study area near Elk City, Idaho. The study area comprises most of the original Mallard RARE II area (1-847) plus some additional lands. The investigation is part of an ongoing, multi-year study of north-central Idaho that is being conducted in cooperation with the Idaho Geological Survey and the U.S. Geological Survey (USGS). The only identified resources are rock suitable for road metal. Five lode prospects and a pyrite-bearing rock quarry, which is operated by the Forest Service for aggregate, were examined for metals. One of the prospects warrants additional exploration for silver in quartz veins, but the chance of finding an economically minable deposit is limited. Several rock and stream sediment samples were anomalous in various metals. Two of the more promising localities for gold and/or other metals are adjacent to a unit of the Frank Church-River of No Return Wilderness that the USGS classified as having a moderate potential for gold deposits related to fossil hot springs.

Jan 1, 1991

By Michael D. Balen

The U.S. Bureau of Mines (Bureau) is currently conducting a four-year study to assess the mineral resources and the mineral development potential of the 5.7 million acre Valdez Creek Mining District (VCMD) located in southcentral Alaska. The VCMD study is part of the Bureau's ongoing statewide mining district evaluation program. This report is a summary of the 1988 field work. The field work involved collection of reconnaissance placer and rock samples, and also involved sampling and examination of the mines, prospects, and mineral occurrences which were identified by literature research of the geology, exploration history, and mining history of the district. During the 1988 field season, Bureau personnel spent a total of 11 weeks in the field, collected 1,006 rock and placer samples, and located, mapped, and sampled 106 of the known mineral occurrences. The Bureau has visited 243 of the 250 known mineral occurrences during the course of the VCMD project. Reconnaissance sampling for placer occurrences resulted in the identification of 4 previously unreported gold placer occurrences, and identification of 5 occurrences that contain detectable levels of platinum or palladium. Reconnaissance sampling for lode sources of base and precious metals resulted in the identification of 5 new Lode gold-silver occurrences, identification of 2 occurrences that contain elevated quantities of chromium, cobalt, nickel, palladium, and platinum, and identification of one occurrence that contains elevated quantities of copper, molybdenum, anti zinc.

Jan 1, 2011

By S. L. Gerhard

In the United States the performance characteristics of permissible explosives are controlled by routine tests, which include firing the explosive into a gallery filled with a methane-air mixture. These tests are made by the staff-of the Explosives Division of the Bureau of Mines and are similar, in general, to those employed in other countries. This control has helped to reduce the frequency of accidents involving the ignition of firedamp by explosives but has not clarified the basic causes of the ignition. To advance this control and to minimize potential hazards further, this fundamental knowledge is needed. Some of the results of recent research on the causes of the ignition are described herein. NATURE OF THE PROBLEM When an explosive ignites firedamp in the gallery tests, the source of the ignition must be one or more of the emissions from the steel borehole. It has been accepted generally that these emissions are (1) particles, (2) the shock wave, and (3) hot gases and flames. Photographs show that the shock wave emerges from the borehole first, followed closely by hot gases. At first the velocities of these are high and approximately equal, but the velocity of the gases decreases more rapidly than that of the shock wave, and by the time the reactions causing the flame are complete the shock wave travels in an otherwise undisturbed medium. The particles are originally enveloped in the hot gases but some soon begin to break through and eventually out-distance the shock wave. The approximate geometry of these emissions about 1 millisecond after the shot is fired is illustrated in figure

Jan 1, 1939