Search Documents

By H. B. Humphrey

In the 39 years from 1891 to 1929 , gas and dust explosions in the coal mines of Tennessee caused 413 deaths , or one- third of the fatalities in the mines for that period . Inasmuch as explosions caused but about 15 per cent of mine fatalities for the whole United States for this same period it is evident that the Tennessee coal mining record is by no means good , as far as explosion fatalities are concerned . Since 1926 , Tennessee has had a clear record as to fatalities from explosions ; this fact may be credited very largely to the improved conditions and safer practices in Tennessee's coal mines which have been brought about by the work of the State Inspection Department and of the Southern Appalachian Coal Operators Association directed toward adoption of safety precautions and practices most of which are advocated by the United States Bureau of Mines . Chief among these improvements are the replacement of black powder and dynamite by permissible explosives , improved ventilation , and the installation of rigid methods of inspection for gas . With the present tendency for operations to pass into the hands of responsible and informed management , and with unrelaxed care and inspection , the good record of the past several years should be maintained .

Apr 1, 1931

By E. P. Youngman

The mining law of the Belgian Congo does not cover the Province of Katanga nor the District of Kivu (in Eastern Province). Regulations of the Comité Spécial du K tanga are in force in Katanga and those of the Comité National du Kivu in Kivu. The three laws differ only in detail, and grants made by the Comité Spécial du Katanga or by the Comité National du Kivu must be approved by the Ministry of Colonies. The following résumé is designed to coordinate the three sets of regulations.

May 1, 1930

By J. H. Jacobs

In late 1946, research was begun at the Bureau of Mines Electrometallurgical Laboratory at Boulder City, Nev., to determine the possibility of electrowinning manganese from chloride electrolytes on a continuous basis. All phases of electrodeposition were investigated on a small scale it the laboratory, and the results were reported by Jacobs and Churchward. These results indicated that a chloride process had certain possible advantages over the sulfate process that made it worthwhile to continue the investigation on a semi-pilot-plant basis, and this paper reports the results of this work. Research and development work on a process for electrowinning manganese from low-grade ores has been carried on intermittently by the Bureau of Mines since 1936. A process was developed, using sulfate electrolyte, that has been extensively described in the literature.

Jan 1, 1951

By Wilder D. Foster

In estimating the hazardous qualities of a dusty atmosphere it is frequently desirable to determine the composition of the air-borne dust. Samples collected from ledges or from the rock itself are Likely to be unsatisfactory for this purpose owing to the possibilities of differential disintegration of the rock and of variations in settling rates of the different components of the minerals. It may be necessary, therefore, to collect samples of dust from the air. Samples collected from the air may be analyzed chemically, by X-ray diffraction, and by the petrographic microscope. Chemical methods are unsatisfactory owing to the small samples usually available and to the limitations and complexities of: present methods. X-ray technique requires expensive apparatus not ordinarily available except in research laboratories. Owing to the simplicity and rapidity of petrographic is examination of atmospheric mineral dusts, it was considered worthy of further study.

Jan 1, 1938

Develop rugged, cost-effective fire protection for hydraulic shovels and backhoes. Approach Automatic fire sensing and suppression systems were designed and built for use on hydraulic shovels and backhoes. How It Works A line-type temperature sensor is mounted in the machine's engine and hydraulic pump areas to detect the heat from a fire while it is still small and easy to control. Two systems were tested. In one, the inside of the sensor consists of two conductors separated by a ceramic material whose electrical resistance decreases with increases in temperature. When heated to a predetermined temperature) the control circuit responds to the resistance drop. In the second system, the detection element of the sensor is comprised of a thin metal tube containing a hydrogen charged metal hydride wire. The tube is sealed at one end and is connected to a sensitive pressure switch at the other end. When exposed to the heat from a fire, hydrogen gas released from the metal hydride wire actuates the pressure switch.

Jan 1, 1980

By Fred S. Karn

Inhibitors are used in coal mines as a precaution against accidental dust explosions. Although rock dust is the usual inhibitor many others have been tested. To facilitate testing a screening process using laser irradiation was proposed. The procedure includes irradiation of a coal-dust mixture followed by mass-spectrometric analysis of the evolved gases and an evaluation of the flammability characteristics of the gases. Carbonate-type inhibitors decreased the percentage of combustibles in the gases generated and inhibitors like NaCI (thermally stable salts) decreased the total gas generated. A suitable test procedure did not result from the investigation, demonstrating the inadequacy of fast heating, non-combustive techniques in rating inhibitors of coal dust explosions.

Jan 1, 1973

By P. Yant, R. R. Sayers, R. D. Lieitch

"PURPOSE OF INVESTIGATIONOf more than 300 bituminous mines examined by Crichton 5 and his assistants in connection with litigation in Indian Creek Valley, Payette County, Pa., only four were found to have alkaline water. That work and many observations from of the authors have shown the general prevalence or acid drainage from bituminous coal mines. In connection with investigations pertinent to coal-mine drainage that are being conducted by the United States Bureau of Mines, it was noted with considerable interest therefore, that a mine in the Thick Freeport bed about 20 miles north of Pittsburgh had no acid water in the workings, As it was thought that this condition might be common to all mines,this condition in this bed most of them were visited, samples of the outflow and from different parts of the mine inside were examined, and such general information as was available was gathered.ACKNOWLEDGMENTSThe authors acknowledge with thanks the courteous assistance of mine officials in connection with collecting the data for this paper, and of the analytical and coal laboratories of the Bureau of Mines for analyses."

Nov 1, 1932

By A. W. Maynard

Simple chemical spot tests for the identification of major alloying elements in aluminum-base alloys are described. The tests are suitable for use by nontechnical personnel working outside a laboratory. Tests for zinc, copper, manganese, and magnesium employ electrographic sampling methods and sample papers. Use of electrographic sampling in a test for magnesium in aluminum is made possible by using glass fiber filter paper. Differentiations between magnesium and magnesium-silicon alloys of aluminum and between aluminum-base and magnesium-base alloys are made by direct chemical solution tests. Description of a device for obtaining reliable electrographic samples is included. A sequence of testing for identification by alloy groups is given.

Jan 1, 1971

By Adrian Brown

Pilot Hole ?X? was drilled to test the formations through which the ventilation shaft for the proposed U.S.B.M. demonstration oil shale mine will be drilled. Five permeability tests were performed at various stratigraphic levels within this hole. The test method used was that of pumping fluids out of the hole for three hours, using the air lift method, followed by a three-hour period where the recharge was observed. Transmissivity and permeability results were determined from these test data. The test procedure used is described and supporting data for the hydrologic tests are provided.

Jan 1, 1977

By J. B. Littlefield

This study is one of at number conducted to determine the concentration of dust in the air during the complete cycle of operation in wet drilling; information as to various factors connected with, drilling in mining operations is considered to be of definite value in the control and prevention of air dustiness, and it in particularly desirable to ascertain whet features of present-day wet-drilling operations in mine work contribute to dust disease and to remedy deficiencies when they are found.

Jan 1, 1938

By Ronald B. Stotelmeyer

This report summarizes studies of 28 National Forest roadless areas in Montana completed by the U.S. Bureau of Mines (USBM) in the period 1974-1993. It also briefly describes 20 areas for which field studies have not been conducted. All 48 of these roadless areas have been recommended for addition to the National Wilderness Preservation System or proposed as special management areas by the U.S. Forest Service (USFS) or the Montana congressional delegation. The Bureau studies indicate which parts of the roadless areas have a high likelihood for mineral-resource development. They also show where mineral production has occurred in the past and where abandoned mine workings (possible hazards) would be encountered. The number of mine and prospect workings found are a measure not only of surface disturbance, but of areas not wilderness in character. For the purposes of this report, mine refers to a property which produced (or is currently producing) a mineral commodity, a prospect is a property which has been explored but has no record of production.

Jan 1, 1994

By Oliver Bowles

This paper is the third of a series of reports on asbestos prepared by the Bureau of Mines. The reports already issued contain general information, including descriptions of deposits throughout the world.3/ The present paper deals chiefly with milling and marketing. Many grades of asbestos are marketed, and an important phase of milling is the grading of fiber; these subjects therefore are related so intimately that contiguity in their treatment is fully justified. Although the Bureau of Mines is interested primarily in the mining and preparation of raw materials, the fabrication of asbestos products has attained such importance in the United States that brief reference to processes of manufacture is included. CLASSIFICATION OF FIBER Canadian asbestos fibers are divided into three main groups - crudes, mill fibers, and shorts. The term "crude" is applied to fiber of spinning grade measuring three eighths inch or longer, that is. hand-cobbed and not passed through a mill. Mill fibers are obtained by crushing and beating the fiber-bearing" rock, until the, asbestos is freed and, then removing the fiber from the rock by screening or air separation. Shorts are the lowest grades of mill products.

Jan 1, 1935

By Takashi Ohya, George V. Keller, Richard G. Geyer

One aspect of a program to improve the chances of survival following coal mine disasters is the development of a communications system which will allow surviving miners to make their circumstances known to rescue teams. At present, it appears that an electromagnetic system may be most practical. The development and design of an effective electromagnetic communications link for signalling between mine workings and the surface requires knowledge of pertinent physical properties of the rocks overlying the mine workings and the characteristics of the ambient noise against which a communications signal must be recognized. Knowledge of the overburden electrical transmission properties is useful not only for determining a practical operating transmitter frequency at a given mine, but also for ensuring the best possible electromagnetic coupling for routine or emergency communication purposes. Field studies of the electrical transmission properties of the overburden of coal mines in Colorado, Illinois, and Pennsylvania generally show that a rela- tively uniform and unimodal electrical conductivity distribution exists provided that the region has not been subject to considerable structural or metamorphic deformation such as that observed in the Gary District of West Virginia. Measurements of ambient surface electromagnetic noise levels at several mines in Colorado, Illinois, and West Virginia were taken and analyzed and are presented in the form of amplitude histogram plots both as a function of frequency and time of day. These amplitude histograms may be used in conjunction with overburden resistivity data in implementing an uplink communications beacon system which will yield a specified signal-to-noise ratio at the surface. Numerous C.W. field transmission tests were made in various coal mining environments with use made of either a buried vertical-axis transmitting loop or a short insulated grounded current line. These transmission tests were made from 20 Hz to 20,000 Hz in frequency and at several geographic surface receiving sites. The results of these field measurements show, in general, good agreement with theoretically calculated results. Since the produced surface magnetic field from a buried vertical-axis loop source or the produced surface horizontal electric field from a buried horizontal current line show better agreement with theoretical results, they could be used for beacon location system. One criterion would be in detecting the equatorial and polar null lines of the horizontal electric field component which is normal to the direction of emplacement of a buried transmitting line current source. A second criterion would be in the surface mapping of the maximum in the vertical magnetic field directly over a vertical-axis loop transmitter and the associated null in the vertical magnetic field at a horizontal offset distance which is about 1.4 times the depth of burial of the transmitter. Finally, a third criterion would lie in the surface mapping of the null in the horizontal magnetic field directly over the vertical-axis beacon and the associated maximum in the horizontal magnetic field at an offset distance from the transmitter axis of half the depth of burial of the loop transmitter. In mapping the vertical magnetic field over a buried vertical-axis loop transmitter, the size effect of the transmitter loop must be taken into account when the separation distances between the transmitter and receiving sensor are less than ten times the effective radius of the source loop; increasing the size of the transmitting source relative to the source-receiver separation distance shifts the null in the vertical magnetic field to greater offsets. In mapping either the vertical or horizontal magnetic field over a buried vertical-axis loop transmitter, care should be exercised in ascertaining that measured nulls and maxima are along radials through the axis of the buried source loop. For the main part, coupling experiments show that ambient electromagnetic noise in coal mining districts is less of a problem above 1000 Hertz. But secondary and perhaps undesirable maxima and null phenomena (as well as penetration problems) would occur in many coal mine provinces in the behavior of the surface horizontal magnetic field (over a buried vertical-axis loop transmitter) if transmission frequencies as high as 10 kHertz were used.

By P. L. Swanson, S. Billington, F. M. Boler, L. H. Estey

Stabiity analyses of fractured and faulted rock masses require delineation of the position, extent, and orientation of geologic discontinuities. The size of the smallest active discontinuity that may potentially be resolved using the spatial distribution of microseismic event locations is limited by the accuracy and precision of the location methods. At a hard-rock mine in the Coeur D'Alene mining district of northern Idaho, two data sets consisting of calibration blast signals from a known source site and origin time and microseismic event signals were recorded using a stope-wide accelerometer array. These seismic signals are used to quantify various sources of error in event location. Five factors influencing source location errors are examined in this US. Bureau of Mines study: (1) biases of the numerical source location techniques, (2) receiver array geometries, (3) uncertainties in receiver positions, (4) errors in picking arrival times, and (5) uncertainties in seismic velocity structure, including the effect of mine openings. In addition, synthetic data (accelerometer positions, travel-time picks and wave velocity) are used to determine the effect of known systematic and random errors on source location calculations. It is shown that the commonly accepted association of minimum travel-time residuals with the best location solution does not necessarily hold true when there is a systematic error in seismic velocity. Recommendations are made for increasing the accuracy and precision of locations of microseismic events detected under similar field conditions.

Jan 1, 1992

By Cavallaro. J. A.

This report presents the results of a washability study of 455 raw coal channel samples with special emphasis on sulfur reduction. These raw coals contained on the average 14.0 percent ash, 1.91 percent pyritic sulfur, and 3.02 percent total sulfur. The complete washability data are presented for each sample processed. A statistical evaluation is included for the coalbeds from which more than 10 samples were collected and for the geographical coal producing regions. A graphical summation is presented for the coal producing regions and selected coalbeds. Finally a similar statistical evaluation is included showing composited data interpolated at Btu recovery levels of 50, 60, 70, 80, 90, and 100 percent. Graphical summations are presented for the various coal producing regions. Generally, significant sulfur reduction is achieved if the coals are crushed to a finer size and the higher specific gravity increments are removed. If a 50-percent Btu recovery was acceptable, then 32 percent of the samples tested could be upgraded to meet the current Environmental Protection Agency (EPA) standard of 1.2 pounds of S02 emission per million (MM) Btu when crushed to 14-mesh top size and separated gravimetrically.

Jan 1, 1976

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

By E. A. Magill

This report is one of a series prepared by the Bureau of Mines on manganese deposits of the Northwestern States. It describes properties on the Olympic Peninsula, Wash. Exploration by the Federal Bureau of Mines in 1939-40 and 1954-55 on several typical deposits is summarized, and examination data are presented for other manganese deposits on the peninsula. An attempt was made to list all known occurrences; however, some properties are abandoned, and their exact location is unknown.

Jan 1, 1960

By Jerry G. Craig

The Bureau of Mines has developed a computerized oil and gas well data retrieval system from studies of the waterflood potential of a producing reservoir. This system stores pertinent information about each well completed in a reservoir and facilitates selection and manipulation of large volumes of data. Use of the system enables reservoir information to be supplied rapidly, accurately, and at less expense.

Jan 1, 1971

By Ovsei Volberg

Motion capture involves recording the position and global orientation of joint sensors of a real object, in most cases a real person performing some human activities. This information is usually recorded at uniformly spaced instances of time, or as it is often called frame-by-frame. Then the recorded motion data sets are processed and mapped into a skeleton hierarchy of a virtual, computer simulated human figure to control the motion of the virtual human in the computer simulation. In the first part of the paper we review several new techniques developed to facilitate the manipulation, noise reduction, storage and reuse of captured data, which have a potential to reduce the overall cost of motion simulation and improve its realism. In the second part of the paper we consider the real life problem of reducing a worker?s risk from being hit by underground mining machinery in a confined space. We formulate a set of requirements to motion editing for this particular task and analyze the limitation of existing techniques

Jan 1, 2000

The investment involved in any communication system represents a considerable sum. Even though it is desirable that the system work properly each and every time it is called into use, some failures are bound to occur. Most failures, however, and especially those that occur most frequently, are due to poor installation techniques. An extra hour spent at an installation site can save many maintenance trips and many frustrating hours of system troubleshooting. Typical faults likely to cause communication outrage are Pager phone systems Poor splices aggravated by corrosion. Strain relief not provided. Drip loop not provided. Incorrect branch connections. Overloading the circuit. Poor battery connections. Improper wire size or type. Lightning strikes. Improper placement of wire runs. Carrier phones Mounting transceiver near load resistors or other sources of heat. Tracks not electrically bonded. Cable abrasion due to poor mounting location. Disconnected battery. Poor mechanical installation. Each installation should be well planned. After an installation is completed, the technician should ask the question, "What can go wrong with this unit or line?" Remember the adage, "Whatever can go wrong, will." Preventive measures taken during installation will pay off in the long run. 6.2 Pager Phone Installation The pager phones used in many underground coal mines are battery-operated, party-line telephones with provisions for loudspeaker paging. The system is usually two-wire, nonpolarized, and operated by self-contained batteries. Many of the individual units are certified as permissible. 6.2.1 Mounting Pager phones are designed to be mounted on an upright support at the desired location. For convenience, the phone should be mounted 5 feet above the floor where there is no obstruction to using the handset or removing the cabinet front cover for servicing or battery replacement. In low-coal situations, a suitable height for installation should be selected convenient to the normal operator's position at the site selected. About 12 inches of free space on each side of the phone should be provided for cabinet access. The phone should be protected against direct exposure to dripping water and should not be allowed to rest in a puddle of water. The mounting location should be convenient to a work location and have a safe, unobstructed area for a worker to stand and use the phone. The phone must be in a location where the worker will not be in the path of moving vehicles or falling debris. Each telephone is normally well insulated, but it is still good practice to provide an insulating mat or dry planking for the user to stand on.

Jan 1, 1984