Search Documents

By E. M. Cohn

The literature dealing with the electrical conductivity of solid dielectrics, including all its aspects and its relationships to other physical properties of these materials, is extensive and scattered in many books, phamphlets, and periodicals. It is believed that most of the important contributions to this field up to October 1943 have been listed and abstracted in this circular. Also included are some general references on static electricity. Methods of removing static charges are described; methods of and conditions for measurements of resistivity are discussed; equations for the calculation of resistivity are given; and methods of resistance measurements in Situ are reviewed. Data on the variations of resistivity with changing conditions as well as explanations for them have been collected, and three tables showing the resistivity of various dielectrics at different humidities are included. The appendix contains a short development of the mathematical formulation of the charging and discharging currents due to interfacial polarisation. INTRODUCTION Methods for Removing Static Electricity Of the various means employed for preventing or removing accumulations of static electricity in industrial processes, grounding is the most common and most generally effective. It is a precaution readily applied to stationary machines anti may often be utilized to good advantage to rid persons and portable equipment of an acquired charge. There are many situations, however, in which direct low-resistance grounding cannot be used, either because the charged bodies are insulators or are inaccessible, or because contact to a ground lead might give rise to a hazardous spark. If the charged body is a conductor, contact made to a neighboring conductor, even though the latter be insulated from ground and of relatively small capacitance, may also result in the occurrence of an incendive spark. In such instances, static electricity can sometimes be removed most satisfactorily by means of strong atmospheric ionization produced by radioactive material, X-rays, ultraviolet light, or A. C. high-voltage brush discharge. Where no danger exists from flammable

Jan 1, 1944

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By D. Harrington

Seldom, if ever, has any mining hazard presented itself that some method has not been devised to control it to some extent; the degree of success of such control depends largely upon the intensity of desire to prevent suffering, injury, and death. The economic saving to be realized and the more definitely this is realized by all concerned, the more quickly and effectively will the hazards be handled is an important incentive to prevention of accidents. Preventing coal-mine explosions is by no means a complex problem; all that is necessary is sensible, conscientious, sustained effort. The fact that explosions can be prevented has been well-demonstrated by the record of the post few years; the average annual death toll from explosions for the 5 years 1906-1910 was 438, and for the 20 years prior to 1929 it was 265: during the past 4 years an average of only 32 deaths per year resulted from this cause, although the annual production during that time varied but slightly from that of 1906-10. This is a truly remarkable reduction, and if other types of mine accidents had been reduced in the same ratio only about 300 would be killed annually in our mines instead of the nearly '1,300 killed in 1936 and the approximately 2,000 killed annually for many years. Although frequency of occurrence of explosions has not lessened greatly during the last decade, their severity decreased markedly, which would indicate that effective means are being taken to prevent the spread of explosions, even though ignitions and their causes are not being handled nearly as effectively as they might or should be handled. Several large coal-producing States, which in the past have experienced numerous disastrous explosions, have been free from such disasters for continuous periods as long as 8 years in the relatively recent past. The application of rock dust to underground surfaces has been an important factor in preventing widespread explosions; some of the mast dangerous mines have been rock-dusted fairly adequately, and this has been amply repaid in the reduced severity of explosions, as heretofore indicated; however, many have applied rock dust apparently without giving much consideration to the amount required to prevent

Jan 1, 1938

By T. Bieniawski

"INTRODUCTION The Congress theme ""Improvement of Mine Productivity and Overall Economics by Modern Technology"" is probably beat: addressed by the subtheme allocated to this Plenary Session. It is appropriate that .Theme 1 emphasizes the simple point that effective use of geotechnical information is the key to improving mine productivity. In essence, this means that: (1) geological and geomechanics, (rock mechanics) data must be collected in sufficient quantity and of high quality; (ii) data interpretation must be performed specifically for purposes of engineering design; (iii) innovative design approaches should be used to bring about Improvements in productivity and safety.While, each of these three aspects .may: seem obvious to any mining engineer it is a fact that the above sequence is seldom followed and as a result, mining engineering not infrequently lags, behind other branches of engineering when it comes to design creativity, efficiency and safety.. . After all, mining is still-one of the most hazardous occupations and we are gathered here to discuss, at the highest world professional forum, how to use more effectively the modern technology. This however, does not mean that mining engineers are less capable than other engineers or that their achievements are any lesser; far from it! Mining engineers are the cream of the engineering society on whose efforts depends the welfare of mankind. Moreover, they have produced minerals and coal evergrowing quantities against evergrowing difficulties. Yet, we must and can become even better because we are not making full use of the modern technology and rock mechanics knowledge already at our disposal, and. we are not being innovative enough to the full extent of .our capabilities."

Jan 1, 1989

By L. W. Scott, T. H. Dubaniewicz, F. T. Duda, P. G. Kovalchik

Recent research conducted by NIOSH, Pittsburgh Research Laboratory showed that electrical current levels permitted under parent regulations may not limit cable temperatures to less than 90 °C in reeled trailing cables. Reeled cables, tightly wrapped with many turns, ell carrying current in an enclosed space, can become overheated due to poor heat transfer. This overheating can cause the cable insulation to soften and become easily damaged. The damaged insulation reduces the life of the cable and can lead to shock, electrocution, and mine foes. This paper describes a method of measuring the conductor temperature of untie trailing cables during no anal operation. The temperature is measured using a 50/175 micrometer Graded Index Multimode Optical Fiber located in the center of the metallic conductors. Distributed temperature measurements arc made using an Optical Time Domain Reflectometer (OTDR). This system is capable of measuring temperature with an accuracy of plus or minus one degree centigrade over a length of 4 km at 1-m intervals. With this unique way of measuring temperature, tests can be conducted simulating actual mine conditions and provide important data to allow MSHA's Approval and Certification Center to develop approval criteria for cyclically rated reeled machines.

By R. C. Hickman

"INTRODUCTION The most productive area of the eastern Virginia pyrite belt lies to the north of the village of Mineral., in Louisa County. The largest producers of pyrite ore in the area were the Armenius, Boyd Smith, and the Sulphur mines.The Boyd Smith mine started production about 1890 and operated more or less continuously until 1922, when competition from the Gulf States and Spain closed the pyrite mines in Virginia. There are no reliable records of production or value of minerals produced.ACKNOWLEDGMENTSIn its program of exploration of mineral deposits, the Bureau of Mines has as its primary objective the most effective utilization of our mineral resources to the end that they take the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurgical Branch, Oliver C. Palston, chief, analyzes samples and performs beneficiation tests.The project was under the immediate supervision of Mitchell H. Kline, chief, Raleigh Division, Mining Branch, Bureau of Mines.LOCATIONThe Boyd Smith property is reached from Mineral, Va., by traveling north on State Route 522 about 2-1/2 miles. An unsurfaced road, winding in a northwesterly direction, loads to the Boyd Smith headframe, which is about half a mile from State Route 522 (fig. 1). The tract comprises 181 acres."

Aug 1, 1947

By VAN. H. MANNING

During the nine years that have elapsed since the Bureau of Mines was established in 1910, the work of the bureau has included many investigations that have proved of high value to the Nation. Eleven mining experiment stations established by act of Congress have greatly increased the bureau's usefulness; being situated in the mining fields, these stations are closely in touch with industrial needs, and the results of their research and educational work are more directly available to those engaged in the mining, metallurgical, and mineral industries. In the United States mining is second in importance to agriculture only. The Federal Government annually appropriates large sums in the interest of agriculture, whereas the appropriations for mining are relatively small. But the nation-wide popularity of Government assistance to agriculture should not overshadow the need of Federal assistance to the mineral industry. With scientific management farms can be made to produce indefinitely without any depletion of the potential resources of the soil, but the mineral wealth of a country is a fixed quantity, and every year's production brings nearer its ulti- mate exhaustion. As the deposits of the richer or more readily available ores, espe- cially those in the West, have been depleted, development of methods for mining and treating the leaner or more inaccessible ores has lagged, so that meeting the increasing demands for certain metals is becoming more and more difficult. In some branches of mining the small inde- pendent operator is greatly handicapped. He has to rely on custom mills and smelters for the profit or loss of his product, and because of relatively inefficient methods of milling or smelting he may receive no return for much of the ore he mines. Even though the small operator thinks he knows of improved methods of obtaining the metals from the ores, he can not afford to install the necessary machinery or to carry on experiments that may or may not prove successful. In view of the increasing need of metals and the impossibility of renewing the ore supplies, efforts should be directed toward developing the most economical and efficient methods in mining and metal- lurgy. The great mining companies carry on independent research work, some of them on a large scale; but as such work is usually undertaken for gainful purposes, these companies do not feel under any obligation to give the results of their investigations to the world. Clearly the solution of the difficulty is to place in the mining districts trained mining and metallurgical engineers who will investigate and solve the problems for the benefit of the whole industry. It is with this purpose in view that experiment stations of the Bureau of Mines have been established to investigate economy, efficiency, and safety in mining, and to make public the results of the investigations. The Federal Government can be of most help in developing the mineral resources of the country when its forces are brought in direct contact with these resources. Mining is as old as civilization, but only within a generation has this country busied itself with any other problem of mining than the amount of mineral products that could be put upon the market. Little concern was felt if much of the metal in an ore was wasted, if the miner lived in unsanitary surround- ings and died of preventable disease, or if accidents occurred fre- quently and from causes that could easily be controlled. Now we realize that the waste of any resource is inexcusable. The mineral wealth of the country can be mined but once. The task before the Nation is to recover as much metal as possible from the ore in the ground, and to do this in the most economical way without waste of human life. This task is of such magnitude as to warrant aid from the Government through experiment stations. In its efforts to make the work of these stations of most benefit to the mineral industry the Bureau of Mines seeks the cooperation of State authorities, of mine operators, of miners' organizations, and of every person interested. These experiment stations also serve an educational purpose. Gen- erally speaking, mining is not a preferred occupation. The miner should have reason to take greater interest in his work; he should feel that the experiments the Government is making affect him vitally by enabling him to increase his production and by making his work safer. The mine operator should realize that the Government stands ready to aid him, and he should know that he can bring his own problems to a Government organization that is trained and equipped to solve them. The surest method of accomplishing these results is to carry the work of the Bureau of Mines into the mining regions through the establishment of experiment stations easily accessible both to the mine operator and to the miner. Many miners in this country do not read English, but they can understand motion pictures of mining methods; they can learn how lives can be saved in case of accident; and they can appreciate the larger results gained by modern methods and equipment. In every

Jan 1, 1919

By Robert S. Sanford

"INTRODUCTION AND SUMMARYThis paper is one of a series recently undertaken by the Mining Branch, Bureau of Mines, College Park, Md., to describe current practice in hauling ore and waste by truck at various mines.Heavy-duty ore trucks are replacing railroads at many large open-cut mines and even at a few underground mines. Recently a few mines have been equipped with trucks for transporting ore to a central point, from which conveyor belts move the ore out of the mine. This paper deals only with truck haulage methods and costs.The requirements for efficient low-cost truck haulage are good trucks designed for heavy loads, adequate truck maintenance, smooth roads, and well-trained truck drivers.A correct balance must be maintained between the primary crusher capacity, the number of shovels loading ore, and the number of trucks hauling ore.The cost of tires is important. Tire companies are manufacturing better tires. Mining companies are prolonging the life of tires by building better roads and maintaining correct tire pressure.The trend is toward heavier equipment. In 1949 it cost $0.0925 a long ton to haul ore and waste with a 15-ton truck and $0.0743 a long ton with a 22-ton truck.When trucks are properly maintained, hauling costs do not increase with the age of the trucks. During 1948 it cost $0.1118 per long ton to haul with the four oldest 15-ton trucks and $0.1130 per long ton to haul with the four newest 15-ton trucks, two of which were purchased in 1945 and two in 1947.The weighted ayerage cost of hauling a long ton of ore to the crusher and waste to the dump has been reduced from $0.1159 in 1948 to $0.087 in 1949."

Oct 1, 1950

By P. G. Clites

This study was conducted to determine the patterns of heat transfer to water-cooled copper crucibles during vacuum arc melting. Values of heat flux from the ingot to the crucible were determined during nonconsumable electrode vacuum arc melting of zirconium and during consumable electrode vacuum arc melting of titanium) zirconium) and steel. The results of these studies con-firm the existence of a high thermal resistance between the ingot and the crucible wall which results from the shrinkage of the ingot as the metal solidifies. Maximum heat flux occurs near the top of the ingot where maximum values of heat flux of 1.4 X 106 Btu/ft2 hr were observed during small-scale consumable electrode arc melting of zirconium and titanium. The maximum heat flux for consumable electrode arc melting of 8-inch-diameter ingots was 0.5 X 106 Btu/ft2 hr. The effects of electrode material) electrode diameter) arc current) and arc potential on heat flux from the ingot to the crucible were studied. Data were also obtained on crucible wall temperatures and on the effect of very narrow annular water jackets.

Jan 1, 1967

By M. D. Carver

This publication describes development by the Bureau of Mines of a quality evaluation procedure for certifying the adequacy of production lots of Kroll process zirconium sponge the Bureau had produced for reactor applications. After the procedure was devised, the next step was to apply it in controlling the quality of one-half million pounds of zirconium sponge com-prising 259 production lots, called blends, originating at the Metallurgy Research Center of the Bureau at Albany, Oreg. The Bureau concluded that the evaluation method developed was adequate and that by this method the zirconium blends having impurity levels or other property values outside specification limits were differentiated and thus were diverted from nuclear energy end uses. The research was performed under contract for the Bureau of Ships, Department of the Navy, and for the Atomic Energy Commission (AEC).

Jan 1, 1960

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By R. Hogg

"The basic population balance models for agglomeration processes are reviewed and procedures are described for extending their applicability to systems with size-dependent rate constants and to the formation and growth of porous agglomerates from rigid, solid-particles. Simplified procedures for the further extension of the models to include simultaneous agglomerate growth and breakage are also described.INTRODUCTION The association of small particles into clusters or agglomerates is a significant factor in many facets of particle processing. Agglomeration processes are widely used to facilitate handling, storage and utilization of fine powders. Processes such as coagulation or flocculation are used to aid solid-fluid separation in dispersed particulate systems. Agglomeration also occurs as an accompaniment, often unwanted, to other particulate processing operations such as fine grinding, mixing and blending, transport and flow.Reliable agglomeration models are needed for improved understanding of the processes in general and of the complex role of numerous, interacting variables as well as for direct application to the design and control of industrial processes such as flocculation, granulation and pelletization. Ideally, the models should account for the primary forces responsible for agglomerate formation and growth, the effects of external forces on process dynamics, the development of agglomerate structure and its role in the process itself, and the effects of concurrent processes such as structure modification (e.g. compaction) and agglomerate breakage or degradation."

Jan 1, 1989

By Ann G. Kim

The Bureau of Mines investigated factors that influence the formation of methane and other hydrocarbon gases in coal, which is an integral part of the coalification process. Coalification begins with a biogenetic stage in which plant debris decomposes and peat is formed; methane and CO2 are the predominant gases produced during this stage. During the diagenetic stage of coalification hydrogen and the hydrocarbon gases methane, ethane, ethylene, propane, propylene, butene, iso-and normal butane, and pentane are formed by dissociation of the organic material. Methane may also be produced by a secondary reaction of hydrogen with unsaturates or by the reduction of CO2. The gas contained in coalbeds is a mixture of methane, C2 through C5 alkanes, CO2, O2, N2, H2, and He; its heating value is equivalent to that of natural gas. The gas content of coal depends on many variables, but an empirical relationship between adsorptive capacity, rank, and depth has been observed.

Jan 1, 1978

By D. Harrington

The occurrence of dust in mines has always been a source of trouble, but for any years, and virtually up to the beginning of the present century, relatively little of a definite nature was known as to the numerous ill effects of dust in mining operations. Even today, with the west amount of time given and attention paid (for at least 40 years in various, countries) to research and observation en dust in mining, and in spite of the experience with it, much information remains to be obtained, before definite, well-authenticated statements can be made as to numerous features connected with the occurrence of dust in Dines an of its effect upon the health and safety of the worker. One statement that can be made with relatively good assurance of being uncontradicted in that dust is a real menace to the well-being of mine workers, and this includes both health and safety. In addition, dust in and around mines and mining plants is one cause of large financial losses to mine owners and operators. FORMATION OF DUST IN COAL MINES IN THE UNITED STATES One definition of mining is "the processes by which useful materials are obtained from the earth's crust; " since virtually all of the useful materials of or in the earth's crust either are solids or must be reached by penetrating through solids, the materials that are moved in mining must necessarily be broken or disrupted, so that almost every phase of the work of loosening the material and transporting it is likely to produce dust.

Jan 1, 1939

By C. E. Wicks, J. E. Tress, F. E. Block

The Bureau of Mines investigated the effects of gamma radiation on materials and chemical reactions to obtain information that could be of value in modern metallurgical practices . Various combinations of metals and their ores and compounds were irradiated in attempts to effect reactions that might be applicable in the extraction and separation of metal values from minerals and The types of reactions studied included complexing of salts , decomposition of hydrated salts , metal chlorination reactions , leaching of ores and minerals , halogen exchange , and various reducing reactions . All irradiations were performed at the Materials Testing Reactor Gamma Facility of the U.S. Atomic Energy Commission at Idaho Falls , Idaho . Spent fuel elements were utilized as the source of the gamma radiation . Some irradiation - induced changes , ranging from mere color change to participation in chemical reactions , were noted . The greatest value of these investigations , however , was the experience acquired , which should be valuable in future explorations of similar nature .

Jan 1, 1964

By M. R. Geer, H. F. Yancey

"INTRODUCTION With the advent of war in 1941, military operations in Alaska were enlarged on such a scale that the demand for coal in the Territory more than doubled. Coal was needed urgently for heating forts and other military establishments, for use on large construction projects, and for handling the greatly increased volume of traffic on the Alaska Railroad. -The additional tonnage required, estimated at perhaps 250,000 tons per year, probably could have been supplied by the United States, but shipping space between Pacific Coast ports and Alaska was already overburdened with military supplies and construction materials. Moreover, although of only secondary importance in wartime, the cost of coal shipped into the Territory is reported to have been as high as $40 per ton. The alternative to importing coal was, of course, to increase the Production of the Alaska mines.Production of coal in Alaska reached, 350,000 tons in 1944, or more than double the prewar' output. The responsibility for increasing coal production was assumed largely by the Army, A Coal Commission attached to the Alaska Department arranged financial assistance for some mining operations, aided the operators in producing equipment for mechanization, and provided most of the labor necessary to operate the mines. The Bureau of Mines contributed to the program in several ways. First, exploration by the Bureau in the Moose Creek district revealed a substantial tonnage of coal of better grade than any currently mined in the Territory, 4/ and drilling in the Broad Pass district, where a mine to supply coal for the army had been started, revealed that the reserves were far less than had been supposed; this operation was abandoned. Second, coal-preparation practices were studied, and recommendations for improvements made, at two of the operating mines at which the quality of the coal makes preparation a factor of vital importance. Some of the information obtained in these studies forms the basis for the present report."

Jan 1, 1946

By Edward A. Barrett, Roberta A. Calhoun

Introduction This Instructor’s Copy contains most of the information needed to use the Wearing Hearing Protection Properly 3-D training reel. It offers practical suggestions on how to use the reel as a training aid, performance objectives for deciding if the training is appropriate for your needs, and discussion notes that provide additional information to the user. The 3-D reel was designed as a self-teaching aid that drillers and others who work at a drill site can use wherever the opportunity for such training presents itself. The latter could be a company preshift requirement or a tailgate session where workers would have an opportunity to view and discuss the reel. It could also be an individual looking at the reel in a pickup truck prior to beginning work at a drill site. The 3-D training reel is versatile in that it can be used for a small group of persons or for a single worker. For any of these situations, information is transferred to the individual by viewing each of the seven colorful, in-depth 3-D scenes and relating the words that appear in each scene to what is depicted in the visual. Acknowledgment The authors thank Linda J. McWilliams, Statistician, NIOSH Pittsburgh Research Laboratory, for her assistance in analyzing the experimental data in this document.

Jan 11, 2004

By J. M. Kuchta

Ignition and flammability test methods were developed by the Bureau of Mines for use in the classification of flammable solids by the Department of Transportation. A rotating disk ignition apparatus and a flame-spread-rate apparatus are proposed for determining the ignitability and flammability, respectively, of most flammable solids. Extremely flammable solids, such as pyrophoric materials, are evaluated by determining their ease of spontaneous ignition in an environmental chamber at high-humidity conditions. Data are presented for various representative solids to show the reliability of the test methods for classifying the materials. A classification system is also proposed for use in government transportation regulations.

Jan 1, 1972

By Rimas Pakalnis, Andrea M. Ouchi, Thomas M. Brady, Mary M. MacLaughlin, Cristian Caceres, Paul Hughes

A major focus of ground control research presently being conducted by the Geomechanics Group at the University of British Columbia, Canada, in conjunction with the National Institute for Occupational Safety and Health’s (NIOSH) Spokane Research Laboratory, is the development of design guidelines for underground mining within weak rock masses. The study expands upon the span design curve for man-entry operations and the stability graph for nonentry operations developed at UBC by extending the application to weak rock masses. The original database has been augmented by weak rock mass information from mines throughout the United States, Canada, Australia, Indonesia, and Europe. The common factor in all of these mines is the presence of a weak back and/or walls. This paper expands on the North American database and how the design curves have been employed at mining operations throughout the world. The definition of a weak rock mass for this study has been defined as having an RMR76 under 45% and/or a Q-value under 1.0.

Jan 5, 2007

By Jonnie M. Estes

A two-constant equation is presented for helium from 30° = T = 1,473° K. This equation is developed by modifying a generalized equation of state originally presented by Redlich and Kwong (20).3 The modification consists of setting B = 0.06372 Tc/PeT. This modified equation represents the compressibility factors of each of 80 isotherms tested in this temperature range to less than 1 percent average deviation.

Jan 1, 1967