Search Documents

By E. C. Lane

During the past 15 years the Bureau of Mines has made and published several hundred analyses of typical petroleums and has developed a system of interpreting the analyses and of classifying crude oils. In describing crude petroleum frequent reference is made to the "base" of the oil, a usage the petroleum industry has found convenient. As part of its general study of the characteristics of crude oils, therefore, the Bureau of Mines has developed a system of classifying them according to "base." This system as first published in 1927 was limited to four classes and in its original form is no longer considered adequate. Since the system was first published the Bureau has analyzed a large number of crude oil, including representative samples from nearly every important producing field in the world, and has found that the system of classification could be revised and amplified to advantage. The revised system is presented herein.

Jan 1, 1935

BIBLIOGRAPHY Allen, C.A, Analyses of Utah Coals, United States Bureau of Mines Technical Paper 345, 1925, pp. 90. Allen, J.E. and E.M. Baldwin, Geology and Coal Resources of the Coos Bay Quadrangle, Oregon, Oregon Department of Geology and Mineral Industries Bulletin 27, 1944, pp. 160. "Aluminum Boom Raises Productivity", Coal Age, Vol. 82, No.6, June, 1977, pp. 103.

Jan 1, 1978

By T. Estelle Gardner

The Bureau of Mines made enthalpy measurements on sodium bromide and sodium iodide in the temperature range 400° to 1,200° K using an ice calorimeter. Equations representing enthalpy as a function of temperature were derived from the data by the method of least squares. These equations were used to calculate smooth values of heat capacity, enthalpy, and entropy at 50° K intervals from the ice point to 1,200° K. The melting point determined for sodium bromide was 1,020° K; the melting point of sodium iodide was 934° K. The heats of fusion of sodium bromide and sodium iodide were calculated to be 6,270 and 5,680 cal/mole, respectively.

Jan 1, 1967

By L. Nahai

Iran's petroleum industry is nearly 50 years old and the oldest in the Near East. According to published figures, Iran ranks third in production and reserves in the Near East. These reserves (including probable reserves) are estimated at 35 billion barrels and constitute about 11 percent of the world's total. Iran is the sixth largest producer of crude petroleum in the world. The 1961 output of more than 430 million barrels was 5 percent of total world out-put for the year. In the same year, Iran ranked fourth among world petroleum exporters, providing 8.4 percent of total world exports.

Jan 1, 1963

By C. B. Davison

One goal of the Bureau of Mines is to conserve the Nation's mineral resources by developing improved performance materials. Consistent with this goal, the Bureau conducted studies on the formation of undesirable cristobalite in seven different fire clays used as refractories. The studies employed scanning electron micrography, chemical and X-ray analyses, and pyrometric cone equivalent determinations to examine the sample clays and determine the effect of thermal history and stablilizing additives on the amount of cristobalite in various calcines. This research has indicated that as fire clay calcining temperatures increased from 1390° to 1,490° C there was a gradual decrease in the percent of cristobalite present in the calcines and a progressive development of mullite crystallization. No cristobalite was found in fire clays calcined above 1,550° C, but cristobalite reappeared when the calcines were reheated to temperatures between 1,400° and 1,500° C. The research also revealed that additions of lithium fluoride (LiF) prevented formation of cristobalite in fire clay calcines.

Jan 1, 1979

By Russell Griffin

The current state of the art of fire and smoke detection technology is reviewed from the standpoint of suitability for use in under- ground metal and nonmetal mines. Detection modes, fire signatures, and environmental considerations are included. Preliminary results of long- term, in-mine tests are presented.

By J. W. Town

This report summarizes the results of laboratory investigations made by the Bureau c! Mines on the recovery of mercury from caustic sulfide solutions by aluminum precipitation and by electrodeposition. Statistical methods were used to design the experiments and evaluate the resulting data. Precipitation studies demonstrated tint metallic mercury could be recovered from mercury sulfide-sodium sulfide solutions with aluminum. Other metals and their salts and aluminum, salts precipitated only black mercury sulfide. Over 95 percent of the mercury was precipitated from solutions prepared with reagent-grade chemicals and from cinnabar leach solutions. Two equivalents of aluminum were required to obtain 95 percent precipitation of the mercury. Under optimum conditions 1 gram of aluminum precipitated from 4 to 7 grams of mercury; the excess Aluminum was recovered for reuse. The effects of time and temperature on the precipitation of mercury were minor when compared with the effects of mercury concentration and aluminum equivalents. The particle size of aluminum had no significant effect over the ranges studied. When aluminum was used as a precipitant, the mercury concentration in solution was reduced to below 1.0 grams per liter. Adding arsenic and antimony sulfides to the mercury solution resulted in their coprecipitation with the mercury when the aluminum was added From 95 to 99 percent of both the arsenic and antimony were precipitated as metal, which amalgamated with the mercury.

Jan 1, 1962

By Forrest T. Moyer

Injury experience at coal mines and mechanical-cleaning plants (excluding officeworkers ) in 1967 was 222 fatal and 10,115 nonfatal disabling work injuries during an exposure time of 241.8 million man-hours. These injuries occurred at a frequency rate of 42-75 per million man-hours worked; the severity rate was 7,699 days lost or charged per million man-hours. Each of these general measures of injury experience was lower than similar data recorded for 1966. Employment at 6,885 coal mines and 569 mechanical-cleaning plants, excluding officeworkers, averaged 139,312 men in 1967. The average number of days worked was 220. Coal production totaled 560.8 million short tons, at rates of 2.32 tons per man-hour and 18.32 tons per man-day. A total of 2,779 onsite officeworkers at coal mines and mechanical- cleaning plants worked 5.2 million man-hours in 1967 without a disabling work injury.

Jan 1, 1972

By Mark R. Stephenson

Everyone knows that mining is a noisy job, but did you know that you are nine times more likely to lose your hearing than someone who works in a quieter job? If unprotected from noise on the job, by age 50, you will probably need hearing aids. Obviously, the best solution is to engineer out the noise, but that isn?t always im­mediately possible. Until mines are quieter, one way you can help save your vital sense of hearing is to use hearing protectors whenever the noise around you is hazardous. Even if you already have some hearing loss, you can use hearing protectors to prevent your hearing from getting worse. When loud noise is present, proper use of hearing protectors will help miners pre-vent most or all noise-induced hearing loss.

Jan 1, 1998

Develop a method to evaluate the effectiveness of coal scam fire surface seals so that potential problems may be corrected at an early stage, before the integrity of the surface seal is lost. Background Surface seals are the primary coal seam fire abatement method being used in the western United States. Surface seals smother a fire by denying it oxygen. The seal is usually constructed by placing a mantle of soil, four to ton feet thick, over a coal scam fire area to exclude air from the fire. The soil is compacted to increase effectiveness, and a soil cement may be used to augment the soil. In some cases, burning coal may be excavated and separately smothered or otherwise extinguished in another area; in other cases, a trench maybe excavated and backfilled with incombustible material to isolate a fire. More often, a surface seal is simply applied over and around the entire known burning area. In the 1950's, the Bureau of Mines administered a large program to treat numerous coal seam Fires across the western United States. Methods used in this program were described in Bureau of Mines Information Circular (IC) 7932, dated 1959. More recently however, various coal seam fires have been treated with surface seals under the direction of state Abandoned Mine Land Reclamation authorities. It has frequently taken years to evaluate the effectiveness of surface seals. By the time problems become evident, it has often been too late to take corrective action within the scope of the original abatement project. For this reason, the Bureau of Mines developed a means for tracking temperature trends at coal seam fire projects to obtain a better and earlier handle on the effectiveness of surface seals.

Jan 1, 1991

By J. J. Cummins

Green River oil shale previously extracted by benzene was heated at 150°, 200°, 250°, 300°, and 350° C for 0.5 to 360 days to determine the rate at which kerogen degrades to thermal products, the types of thermal products formed, and the effect of prolonged low-temperature heating (preheating) upon subsequent assay yields. Thermal decomposition of kerogen at 150° to 350° C is treated as a first-order reaction. The specific reaction rate for kerogen decomposition increases from 2.2 X 10-4 per day at 150° C to 2.0 X 10-1 per day at 350° C. The calculated kerogen activation energy is 19 kcal. Variations in the rate of formation of individual type components of the pyrolytic products were found. Carbon balances show an increase in the amount of kerogen converted to bitumen and oil (from assay of preheated oil shale) as the temperature of preheating increased from 150° to 350° C. Total product from shale preheated at temperatures of 150° and 200° C gave less than 100 percent of Fischer assay yields while the total products from shale preheated at temperatures of 250° to 350° C gave greater than 100 percent of Fischer assay yields.

Jan 1, 1972

By Robert A. Miller

This computer program determines the price per ton of coal needed to obtain a profit of 12 percent discounted cash flow. From a predetermined equipment and manning list, the program calculates all costs and prints seven tables, Including the equipment and manning tables and the discount cash flow table. Forty-four of the input variables may be readily changed to study their effects upon the final price per ton of coal or upon individual cost items. The method is adaptable for any type of mining and with additions, for beneficiation processes. This program was written in Fortran IV for use on the IBM 11302 and with few modifications can be used on other computers.

Jan 1, 1971

By Reynold Q. Shotts

A study was made of the coal resources of an area in Jackson County, Ala., forming a part of the Flat Rock, Henegar, and Stevenson quadrangles. The area studied is a portion of the Plateau coalfield on Sand Mountain and is near the Tennessee Valley Authority's Widows Creek steamplant. Since no detailed geological study of this area had been published, some reconnaissance work was done. The coalbeds and adjacent strata such as sandstones, conglomeratic sandstones, and conglomerates were studied. Available drill logs, together with the areal geology, provided sufficient information to permit correlation of the coalbeds and an estimation of coal reserves. For all categories of reserves, computed on a regional basis, a total of 72,920,000 tons of coal more than 14 inches thick is estimated for the areas studied in Stevenson, Flat Rock, and Henegar quadrangles. Of this tonnage, 40,001,000 tons is estimated to have less than 60 feet of overburden. The total measured coal reserves for the above three quadrangles are 16,359,000 tons, with 12,411,000 tons under less than 60 feet of cover.

Jan 1, 1966

By Bruce K. Cantrell, Jon C. Volkwein

Exposure to mineral aerosol is an occupational health hazard in mining and mineral processing industries because of the risk of developing pneumoconiosis. Agricola (1556) described this hazard for metal mining in Carpathia. He described shortness of breath and consumption, conditions that are now associated with asthma and emphysema. By the end of the nineteenth century, several respiratory diseases were known to affect miners, including silicosis and coal workers' pneumoconiosis (Fletcher, 1948; Seaton et al., 1981). For example, silicosis, not tuberculosis, was clearly recognized as the hazard in the Vermont granite quarries and stone-cutting sheds (McFarland, 1927). The Gauly Bridge Tunnel disaster in the mid-1930s caused the deaths of an estimated 700 workers by acute silicosis and focused the nation's attention on this disease (Cherniack, 1986). By the mid-twentieth century, it was clear that risk of simple pneumoconiosis is associated with a miner's cumulative exposure to mine aerosol in the respirable size range and that prevention lies in reducing that exposure through regulation (Seaton, 1986). In the United States, regulation of mine worker exposure to airborne mine dust is the responsibility of the Mine Safety and Health Administration (MSHA) in the U.S. Department of Labor. The key legislation relating to improved mine worker health was the Federal Coal Mine Health and Safety Act, enacted in 1969 (U.S. Congress, 1969) and subsequently amended as the Federal Mine Safety and Health Act of 1977 (U.S. Congress, 1977). MSHA receives technical assistance from the National Institute for Occupational Safety and Health (NIOSH). NIOSH also provides recommended exposure limits (RELs) for contaminants to MSHA. MSHA's regulation of mines includes the establishment of a dust standard administratively based on the these RELs. Some mine operators must submit a dust control plan designed to meet the dust standard. Periodic mine inspections determine if mines are com- plying with both the dust standard and the dust control plans (MSHA, 1991). The most common dust measurements are those for respirable dust (according to the definition given in Fig. 26-7), that is, the fraction of aerosol particles able to reach the gas exchange region of the lungs. The other health-related size fractions (inhalable and thoracic-see Fig. 25-1, and "total" dust) are also occasionally measured. A "total" dust measurement is defined by the common practice of the last 30 years or so, using 25 mm or 37mm plastic cassettes (e.g., from PAL, MIL, SKC ). The types of mines have been categorized

By O. C. Blade

This report on the properties of motor fuels sold through service stations In the United States was made In accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items Is confidential. 1t presents analytical data for 4, 802 samples, representing the products of 117 companies. The samples were collected during December 1954 and January and February 1955. As in previous surveys, the gasolines covered 6y this survey Include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By E. Shekarchi

A year after the Soviet Union invaded Afghanistan and replaced President Amin with their choice, President Karmal, Afghanistan remained in turmoil. In some respects, the political and economic situation in Afghanistan was no better by the end of 1980 than it was preceding the December 1979 invasion. The Government faced widespread and growing alienation and resistance, virulent factionalism within the ruling party, and an acute shortage of material. The mining sector of the country did not fare better either; the only raw material produced in a significant amount was natural gas, which was exported mainly to the Soviet Union. No statistics on production of other minerals and materials were available by yearend. Most of Afghanistan's gas production was from the Hodja-Gugerdag Field, southeast of Shibarghan. The gas flow from this field had been about 300 million cubic feet per day since 1961. An estimated 230 to 250 million cubic feet per day of Hodja-Gugerdag's production was moved by pipeline across the Amu-Darya River into the Soviet Union. Most of the remainder was transmitted eastward to a 105,000-ton-per-year fertilizer plant and an electric power station built near Mazar-i-Sharif with Soviet assistance. After the Soviet invasion, the second gasfield, Djar-Kuduk, in the Shibarghan area, was brought under production. This field, which will produce about 200 million cubic feet per day, consists of four gas zones in the Jurassic and lower Cretaceous zones between 3,000 and 8.500 feet deep. The gas has a high hydrogen sulfide content, with considerable carbon dioxide, A new treatment plant was built at Djar-Kuduk by Soviet technicians under a turnkey contract at the end of 1980. It is believed that most of the Djar-Kuduk's initial flow will be sent to the Soviet Union.

Jan 1, 1982

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

3. Application of Proposed Revised Standards 57.11-50 to Mines Surveyed 3.1 Subparagraph (a) 1 "Each mine shall have at least two separate and properly maintained escapeways from each working place to the surface which are so positioned that physical or environmental damage to one will not lessen the effective¬ness of the other, and which meet the requirements of travelways and man hoisting standards These escape¬ways shall reach to within 1000 feet horizontally or 300 feet vertically of each working place " 3. 1. 1 Discussion This section will deal with the 1000 and 300 feet distance requirements, Section 3. 5 will deal with the "environmental damage" provisions. During the course of the mine surveys, it became obvious that one mine's 1000 foot distance was nowhere near equal to another' s --not in the actual distance but in the time required to traverse that distance. This -Ls true for the 300-foot requirement as well. The most obvious example is that one could traverse down a 300-foot raise much faster than climbing up the same distance. The temptation is strong to recommend that the distance requirement be changed to travel times instead. However, this approach would unfortunately lead to a lot of subjective evaluations. Having a time requirement for an entire mine evacuation (Subparagraph 6) is one thing, time requirements and the requisite inspection proce¬dures for each working place are quite another.

Jan 1, 1976

By O. C. Ralston, L. H. Duschak, R. D. Pike

Much detailed information on the production of plastic magnesia from magnesite mined near Chewelah, Wash., was accumulated during a cooperative investigation conducted by the Bureau of Mines and the Northwest Magnesite Co. at the laboratories of the University of California in 1919-1921. This bulletin gives mainly the results of the work done with Chewelah magnesite, supplemented by data on similar work with other magnesites, particularly those of California, in the endeavor to produce a plastic magnesia that would be satisfactory for making the so-called " Sorel" cement composition flooring, stucco, and plasters. As standardized methods £or testing such compositions did not exist, it was necessary to examine carefully the various methods in use and choose those that seemed appropriate. In consequence, this report contains many tests made by the methods selected and can be used £or reference by those who wish to adopt standard methods of testing.

Jan 1, 1925

By David J. Kusler

This Bureau of Mines study is an appraisal of the demand for platinum, should this strategic metal be used as a. catalyst in the National abatement of automobile exhaust pollution. The Clean Air Act 0f 1970, as amended, requires that automobiles produced in 1975 and thereafter be provided with antipollutive measures to control automotive exhaust emissions. The study considers the need for automobile pollution control, the methodology for such control, the annual primary (new) platinum demand for automobiles produced from 1975 to 1990, primary platinum availability, and supply-demand forecasts and outlook. The correlative demand for platinum for the production of the required unleaded gasoline is also considered. Methodology for the study included a forecast of new automobile production from 1975 to 1990, development of automobile survival and retirement data, estimates of new platinum demand under various conditions of salvage, and data on recycling the precious metal from the catalytic converters of scrapped vehicles and existing vehicles when their spent converters are exchanged for replacement units. The new platinum demand for automobile exhaust converters, based on a converter service life of 50,000 miles, is estimated to be 1.41 million troy ounces initially in 1975, rising to 1.68 million in 1980, and declining curvi-linearly to 0.94 million in 1990. The platinum demand for converter longevities other than 50,000 miles can be derived from the tabular data presented. An appendix to the report presents a comparison between longevities of 50,000 miles and 25,000 miles. The petroleum industry's demand for new platinum for the production of lead-free gasolines could total as high as 1 million troy ounces between 1972 and 1981, just for expansion of isomerization and reforming capacity, and is in addition to normal operating demand for this metal.

Jan 1, 1972

By Earl C. Lane

This is the second of a series of reports on a survey of petroleum products manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in other parts of the United States, and the claim has been made that some of the present federal Specifications for petroleum products tend to discriminate against California products. The purposes of the present survey are to determine what particular specification requirements California petroleum products characteristically fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what 'lines investigation to determine the question should proceed. The first report* of the series gave the physical and chemical properties of gasoline and mineral spirits made from California crudes. The present report deals with lubricating oils. Sixty-one samples of lubricating stocks and finished commercial products were generously donated by four of the large refining companies of California. Fifteen samples of automobile lubricating oils, made in California from California crudes, were purchased in the open market. Nine samples of lubricating oils mode from Gulf Coast crude were contributed for comparison by a company in Texas. The refining companies have continued the helpful and cordial cooperation shown by them in connection with the earlier work of the survey.

Jan 1, 1923