Search Documents

By Sean Gallagher, William S. Marras, Alan S. Litsky, Deborah Burr

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0, 22.5, and 45). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined.Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01).Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (atleast for older specimens)

By James A. West

COUNTRIES of the Near East, with the world&apos;s largest and insist prolific petroleum resources, produced nearly 277 percent of the world&apos;s estimated total output of crude& oil in 1964 and accounted for about 60 percent of world exports of this commodity. Although petroleum largely dominated the mineral industry of tine area, production of antimony, chromium, copper, mercury, boron, potash, and phosphate rock was of world significance. Production of crude oil in Near East countries reached a record high of 7,520,000 barrels per day in 1964, an increase of nearly 11 percent over that of 1963. Kuwait maintained its position as the leading producer, accounting for almost 28 percent of the area&apos;s output. Saudi Arabia, Iran, and Iraq followed with 22.5, 22.2, and 16.5 percent of total area output, respectively. Despite record production, the Near East, proved crude oil reserve remained in excess of 211 billion barrels, or more than two-thirds of the estimated world proved crude oil reserve.

Jan 1, 1966

By G. E. Bobeck

The first year&apos;s work of a proposed three-year study of the effects of the exposure of coal mine roof rocks to the mine atmosphere has been completed. The project has been terminated. The goal of the project was to determine if possible the mechanism or mechanisms by which coal mine roof rocks interact with the mine atmosphere and weaken, and coupled with mechanical stresses, ultimately fail. The scope of the study was limited to the effects of environmental factors on the deterioration of the rocks. While mechanical stresses may play an important role in the interaction of environmental factors, stress effects were excluded from the study. In order to study the effects of environment on coal mine roof rocks, samples were obtained from several coal mines in the western states. The rocks forming the roofs of most of the mines visited were shales of varying composition. These shales were subjected to numerous tests to determine how the rocks changed with time after exposure. In addition, the identity of the minerals present in the shales was determined by x-ray diffraction analysis and by thermal analysis as well as by optical microscopy

Jan 1, 1973

By James P. Ulery, Jon C. Volkwein

The U.S. Bureau of Mines investigated a method of using inert gas to prevent the formation of explosive gas mixtures in auger highwall mining of coal. A combination of gasoline and diesel engine exhaust gases was introduced into the auger drill hole using a short section of pipe located at the collar. Gas samples were taken and analyzed on-site with infrared detectors for oxygen, carbon dioxide, methane, and carbon monoxide. Evacuated bottle samples were also taken and analyzed by gas chromatography in the laboratory. These gas results were analyzed for explosibility. Coal samples from various depths were used to obtain the gas content of the coal using the modified direct method. Personal expo- sure to carbon monoxide was also monitored. The highest methane level observed was 9.55%. The levels of inert gas (carbon dioxide and nitrogen) were sufficiently high to prevent any ignition of the methane. Results showed that for all conditions during mining, gas concentrations were nonexplosive. The gas content of the coal was about 0.30 cm3/g. The maximum personal time-weighted average sample for carbon monoxide was 20 ppm. This system provides a safe, inexpensive, simple method for pre- venting explosions during auger mining.

Jan 1, 1993

By Stephen D. Cramer

The Bureau of Mines conducted a series of in situ linear polarization measurements in high-temperature, high-pressure hypersaline geothermal brines at the Bureau of Mines Geothermal Test Facility in the Imperial Valley of California. The measurements represented an evaluation of the linear polarization technique for obtaining instantaneous corrosion rates of materials of construction in flowing hypersaline hydrothermal fluids that rapidly form scales on exposed surfaces. A special method was devised for use with the linear polarization technique that resulted in obtaining corrosion rates for 1020 carbon steel, 316 and 430 stainless steel, titanium, various nickel-based alloys, and aluminum 6061 under strong scale-forming conditions. The measurements also provided information on scale-deposition rates in various geothermal environments. Exploratory in situ potentiostatic polarization measurements were made in the flowing brines to qualitatively determine scale-deposition effects on the electrochemical measurements.

Jan 1, 1978

The Production Profile Program is written for use on a Digital Model PDP 11/70 computer using a Fortran IV level G language. It may be run on any system which uses G level or an upward compatible version of Fortran IV language. Please note, however, that the Model PDP 11/70 for which the program was written is programed to read DEC026 type keypunching. If the user&apos;s computer is programed for another type of keypunching it may be necessary to re-keypunch the Production Profile Program. The Production Profile Program uses a fourteen card input. The data must be keypunched according to the layout described in detail in the multiple card layout forms (following). The output from this program must be printed on wide paper, as a full 120 columns are used. The samples of output at the back of this appendix have been reduced for inclusion in this report.

Jan 1, 1977

By William M. Nabors

As a part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers are studying secondary oil-recovery projects in the United States. Published reports that set forth the pertinent facts of these operations help others to profit by the experience gained. This report presents the results of a study of secondary-recovery methods used in Kentucky by the Cumberland Petroleum Co. on its L. C. Bailey lease, Oil Springs pool, Magoffin County, Ky. This is believed to be the first water-flooding project in eastern Kentucky (fig. 1).

Jan 1, 1958

By Paul R. Coyle, Anthony T. Iannacchione

A close look at the Loyalhanna Limestone of southwestern Pennsylvania reveals a complex structural environment. Most exposures of the Loyalhanna occur along Chestnut Ridge and LaurelHill within the Allegheny Mountain Section of the Appalachian Plateaus Province. Because the Loyalhanna is rated as a super-pavement aggregate by the Pennsylvania Department of Transportation and because of its proximity to the population centers of southwestern Pennsylvania, the Loyalhanna has been extensively mined along these prominent anticlinal structures. Geologic and engineering analyses were performed using gas well and core logs, outcrop examinations, underground observations, and mine maps. Strata exposures from both outcrops and quarries were used to construct geologic maps, stereo net, and rose diagram projections so that the Loyalhanna’s structural environment could be understood better. Many of these structural conditions cause ground control problems at local quarries. These problems ranged from small-to-moderate sized rock falls associated with roof jointing to pillar failures associated with dipping discontinuities. Stresses ranged from tensional on structural domes where weathering dominates, to high levels of compression within structural saddles. A greater understanding of these characteristics is a prerequisite to develop engineering controls, such as improved mine layouts, pillar sizes, etc., that lessen miner exposure to these hazards.

By Tye J. Lasich

This project involved modeling rock masses with varying Rock Mass Rating (RMR) values to determine the degree of instability that develops around an underground opening as a function of RMR. The modeling was performed using Itasca?s UDEC distinct element software, which allows explicit modeling of blocks of rock and how they interact with each other. The analyses included three different orientations of the joint sets, four different joint spacings and three different values of joint strength, which combine for a total of 36 different combinations of model parameters. Two different modes of behavior were observed: local failure of area immediately surrounding the roof and sides of the opening, and deep-seated failure extending a large distance beyond the opening. Quantification of the size of the unstable area that developed provides numerical validation of empirical guidelines used in design of ground support and instrumented monitoring systems.

Jan 1, 2005

By Peter J. Clarke

Afghanistan&apos;s mineral industry continued to be dominated by the production and export of natural gas, although several mining and related industrial projects, all under the supervision of Soviet technicians, were in the planning stage in 1982. Afghanistan produced minor quantities of barite, cement, coal, fertilizer materials, iron, and lapis lazuli, all for domestic consumption.2 Large-scale projects being investigated were a copper mine and concentrating plant at Ainak, extensive mining of the Hajigak iron ore deposit near Kabul, construction of an oil refinery at Angot, increasing production and processing of natural gas, and implementing an intensive geologic prospecting and exploration program for areas of mineral potential. Afghanistan&apos;s gross domestic product (GDP) was estimated at $2.76 billion3 and has remained stagnant for the past several years. Total exports in 1982 were estimated at $700 million, only a marginal increase from the 1981 figure of $694 million. Exports of natural gas to the U.S.S.R. earned $385 million in 1982, representing just over one-half of Afghanistan&apos;s total exports. Natural gas revenues were down approximately 11% from the 1981 level, owing primarily to increased antigovernment activity in the northern part of the country.4 About 90% of the country&apos;s natural gas production was exported to the U.S.S.R.5 About 38% of Afghanistan&apos;s development budget had been earmarked for mining and industrial projects in 1982.6

Jan 1, 1984

By Thomas M. Barczak

The initial Support Technology Optimization Program (STOP),Version 1.0, was released at the 19th Ground Control Conference. This original program has since been updated to Version 2.3 which was released in May, 2001. This paper describes the additional features of Version 2.3, focusing primarily on the following three aspects: (1) including uncontrolled convergence into the design requirements for standing roof supports, (2) the addition of design procedures for cable bolts as an alternative secondary roof support, and (3) the addition of new standing roof support technologies. Another new feature which should facilitate the development of design criteria for standing roof support is the capability to define ground reaction curves through convergence measurements alone without having to make support loading measurements. There are several other new features provided in Version 2.3 which are only briefly addressed in the paper. These include: (1) additional graphics capabilities to facilitate rapid assessment of support comparisons, (2)an East-West designation for support selection to more accurately provide cost and support availability data, (3) additional safety measures including a safety factor to identify support design near the peak support capacity, checks to see if the support dimensions comply with aspect ratio requirements, and a measure of roof coverage for the design layout of the support system. These new features of STOP provide more capabilities to design and analyze secondary roof support systems for conditions which could not be fully analyzed in the original version of the program.

By James Westfield

A brief resume follows of some recent activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consultation with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors during their inspections of bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior October 8, 1953, following further consultations with representatives of management and mine workers, and was incorporated by reference in the 1952 and subsequent bituminous-coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reporting to the Coal Mines Administrator any violations of the Federal Mine Safety Code. The inspectors were active in making prompt investigations of hazardous mines that had been closed by order of the Coal Mines Administrator to determine if enough improvements had been made to allow the mines to reopen. Federal coal-mine inspectors also had temporary authority to close mines they found to be imminently dangerous, but such authority (under Executive Order 9728) was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1957

By E. V. Cilento, K. A. DiGregorio, R. C. Lantz

This laboratory has developed a sensitive electro-optical method to quantify the initial rate (R) and total amount.(MAX) of superoxide (SO) produced by single pulmonary alveolar macrophages (PAM). The method uses a microscope to visualize PAM in culture, and to video record the images during the time the cells produce SO. MAX and R are calculated from measurement of temporal changes in optical density in the images due to precipitated diformazan formed by the reaction of SO, produced by each PAM, with nitroblue tetrazolium present in the culture medium. To date, values of Rand MAX, measured due to adherence of PAM to the dish, have been compared to values obtained when quartz, coal mine dust (CMD), and kaolin were added to the medium (in vitro). R and MAX have also been calculated for PAM lavaged from animals exposed to quartz and CMD in the WVU Inhalation Facility. Presently, experiments are being done using serum which permits PAM to be restimulated by different dusts to help establish a dose response effect, and a means to study the effects of lung surfactant on modifying the toxicity of inhaled dusts. Long term, this methodology should provide useful insight· into establishing the role SO plays in the phagocytosis of inhaled dusts and bacteria, in PAM dysfunction, and in lung diseases such as pneumoconioses. Supported by the Department of the Interior's Mineral Institute Program administered by the Bureau of Mines through the Generic Mineral Technology Center for Respirable Dust (G1135142).

Jan 1, 1988

By D. A. Paice, A. B. Shimp

A test program was conducted to determine the adequacy of molded case circuit breakers for dc electrical systems in coal mines. Mine electrical system parameters and the most severe operating conditions to be expected were determined. Tests of the interrupting capabilities of several molded case breakers were made under the worst conditions to be expected. Continuous and pulsed current carrying capability of the breakers was also investigated. Breakers from two different manufacturers passed all tests successfully. Based on the results of these tests, a set of guidelines for applying molded case breakers to dc systems has been prepared.

Jan 1, 1975

By A. F. Colombo

Infrared spectroscopy employing attenuated total reflectance (ATR) techniques on thin films of dried gelatinized starch solution was used during Bureau of Mines research to determine the structural and impurity differences in starch products and to correlate these characteristics with the flotation response of a nonmagnetic taconite. All of the starch products evaluated gave spectrograms which were characteristic of the anhydroglucose monomer and its polymerization product. Distinct infrared absorption peaks caused by the protein molecule were observed and were used to classify the starches. Correlation of laboratory flotation of calcium-activated gangue from a Mesabi Range nonmagnetic taconite and infrared spectra produced from gelatinized starches showed that protein impurities and linear chain structure limited the effectiveness of starches as iron mineral depressants. Starch products having spectrograms similar to pure amylopectin were generally good depressants for iron oxides, were effective at about one-half the addition that was required for starches that gave infrared responses similar to pure amylose, and yielded acceptable iron concentrates containing 61.5 percent iron and 6.5 percent silica.

Jan 1, 1969

By Tom Retka

This three volume final report summarizes the activities and conclusions of this contract. The objective of the contract was to develop noise control modifications on a retrofit basis, for auger miner coal-cutting systems. Manuals were prepared to assist mine shop personnel in retrofitting the auger miner with these noise controls. Final Report Volume I - Details all vibration and acoustical tests conducted in development of the noise controls. Final Report Volume II - Noise Control Modification Manual for the Jeffrey 100-L Auger Miner describes the various noise control modifications to the auger miner, along with fabrication procedures, cost and vendor information. Final Report Volume III - Noise Control Modification Manual for the Jeffrey 94-L Bridge Conveyor describes the various noise control modifications to the bridge conveyor, along with fabrication procedures, cost and vendor information.

Jan 1, 1978

By M. M. Tilman

The Bureau of Mines conducted research to evaluate superplastic behavior in commercial magnesium-base alloys AZ6IA, ZK60A, ZW3, AZ3IB, ZWI, and an experimental Mg-12 pct Al alloy. Strain-rate sensitivity indices (m-values), maximum elongations, and effects of superplastic elongation on tensile properties were determined on fine-grained sheet. Inert-gas-pressure hemisphere-forming tests were conducted on selected sheet stock of the five alloys. Formability trials on AZ31B alloy sheet were conducted on industrial equipment for comparison with commercial superplastic forming of Zn-AI alloy. Closed-die-forming tests were performed on extruded ZK60A rod. All alloys exhibited well over 100-pct elongation, indicating superplasticity, at temperatures and strain rates near the maximum m-values. Tensile properties were generally reduced following 100-pct superplastic elongation, but not to an extent that would preclude use of the commercial alloys in the superplastically deformed condition. The potential for industrial superplastic forming of AZ31B sheet was indicated by hemisphere forming in the laboratory and substantiated in industrial forming trials.

Jan 1, 1982

By S. Malhotra

Processes for the recovery of manganese contained in low-grade domestic sources are evaluated. Conclusions are based on analysis of literature, technical evaluation and cost analysis. The Nossen Nitric Acid Process, the Sulfuric Dioxide Process rind the Ammonia Leach Process should be developed further as they offer the hunt opportunity for commercialization.

Jan 1, 1984

By Charles E. Larson

Square Butte has no history of mineral development or production. Surface mapping, radiometric surveys and chemical analyses of rock samples reveal no mineral potential. The area has a speculative potential for petroleum and natural gas. INTRODUCTION The Square Butte Instant Wilderness Study Area, in Chouteau County, Montana, consists of 1,946 acres (788 ha) about 35 miles (56 km) southeast of Fort Benton and 50 miles (80 km) northwest of Lewistown (fig. 1). This study was performed under provisions of the Federal Land Policy and Management Act (Public Law 94-579, October 21, 1976), in conjunction with the U.S. Geological Survey, which is responsible for regional geological, geochemical, and geophysical investigations, and the U.S. Bureau of Mines, which determines the mineral potential of existing mines, prospects, or mineralized areas.

Jan 1, 1982

By Sean Gallagher

Background. There is currently little information regarding factors associated with specific modes of motion segment failure using a fatigue failure model. Methods. Thirty-six human lumbar motion segments were fatigue tested using spinal compressive and shear loads that simulated lifting a 9 kg weight in three torso flexion angles (0°, 22.5°, and 45°). Twenty-five segments failed via fatigue prior to the 10,000 cycle maximum. These specimens were visually inspected and dissected so that the mode(s) of failure could be determined. Failure modes included endplate fractures (classified into nine varieties), vertebral body fractures, and/or zygapophysial joint disruption. Logistic regression analyses were performed to determine whether certain morphometric variables, amount of motion segment flexion, disk degeneration scores, and/or loading characteristics were associated with the occurrence of specific failure modes. Findings. Results indicated that stellate endplate fractures were associated with increased posterior shear forces (P < 0.05) and less degenerated discs (P < 0.01). Fractures running laterally across the endplate were associated with motion segments having larger volumes (P < 0.01). Endplate depression was more common in smaller specimens (P < 0.01), as well as those experiencing increased posterior shear force (P < 0.05). Zygapophysial joint damage was more likely to occur in a neutral posture (P < 0.01). Interpretation. These results suggest that prediction of failure modes (e.g., specific endplate fracture patterns) may be possible (at least for older specimens) given knowledge of the spinal loads along with certain characteristics of the lumbar spine. Published by Elsevier Ltd. Keywords: Lumbar spine; Endplate fractures; Zygapophysial joints; Morphometry; Disk degeneration; Motion segments; Aging

Jan 1, 2006