Search Documents

By S. R. B. Cooke, J. Bruce Clemmer, F. P. Diener

"The limestone deposit utilized by one of the plants of the Universal Atlas Cement Co. is covered in part by a stratum of cherty limestone. If this overlying deposit could be utilized by removing the excess of chert economically, quarry costs could be reduced and the amount of rock economically available would be increased greatly. On account of the distribution of flint and limestone, a product fairly free of flint can be obtained until the quarry face is about 50 or 55 feet high. As the face is worked farther back into the hill, the comparatively clean stone is overlain with a constantly increasing amount of high-flint limestone. If this flint remained with the limestone, there would be a prohititively high silica ratio in the finished cement; if the flinty layer were removed as overburden a very large tonnage would be handled and much good stone lost. Consequently it was felt that means should be devised for separating the flint from the limestone after it reaches the plant.The investigation was undertaken by the Mississippi Valley Experiment Station of the United States Bureau of Mines in cooperation with the Universal Atlas Cement Co. and the Missouri School of Mines and Metallurgy, Rolla, Mo.CONSIDERATION OF PROCESSESMany schemes for the separation of Minerals are based on differences in the specific gravities of the minerals to be separated. In this case the flint has a specific gravity of approximately 2.62 while the limestone averages about 2.70. This differential is not large enough to permit separation by any method based on specific gravity. Furthermore, all the limestone particles in any given sample are not alike; usually about 10 percent of them have a specific gravity the same as, or lower than, the flint."

Mar 1, 1935

YOUR mom was right …count to 10. Most workers today report that they find their jobs stressful. Miners, in particular, are faced with hazardous and changing environments. Every shift provides different conditions and challenges. Coping with stress is an important tool to maintain your physical and mental health. Now, back to mom. Studies on stress tell us that shifting your focus away from what is causing your stress increases your ability to cope. Counting to 10 is one method. Science proves mom right. The stress response We are born with the stress response, which is a survival instinct, sometimes called the "fight or flight" response. When approached by a tiger in the jungle, our ancestors would perceive danger and prepare to fight or run. The body prepares for the fight or flight response in a number of ways. The bloodstream brings extra glucose and oxygen (fuel) to the heart, the sense of pain is dulled, and memory and thinking improve. The pupils dilate for better vision and the lungs take in more oxygen, while heart rate and blood pressure increase. Body hairs become erect, as puffed-out hair makes an animal look bigger and more dangerous. Once the perceived danger is gone - we have run fast enough to get away from the tiger or won the fight - the body returns to normal functions. Unfortunately, civilization gives us too many opportunities to experience this response. If activated too often, it can create wear and tear on the body, which may lead to injury and illness. Chronic and traumatic stress There are two key types of stress: chronic stress and traumatic stress. Both types can cause both physical and psychological symptoms. Chronic stress builds up from the day-to-day hassles. Traumatic stress results from a traumatic event such as a natural disaster, a mine disaster, or the sudden death of a loved one. Chronic stress is associated with an increased risk of a number of health problems including heart disease, depression, back pain, and carpal tunnel syndrome. Traumatic stress may lead to post- traumatic stress disorder (PTSD), Miners may experience both chronic and traumatic stress in their work.

By Burke Cartwright, S. F. Ravitz, Lloyd R. Michaels

This method is similar to the reduction of dolomite by ferrosilicon, in that it does not require the direct use of electrical energy; like ferrosilicon, the calcium carbide must be produced in an electric furnace, so that the reducing agent in both processes may be considered in some respects as “stored” electrical energy. The reduction of magnesium chloride by calcium carbide is exothermic, takes place rapidly at ordinary pressure and at relatively low temperatures, and can be carried out in ordinary steel equipment, whereas the reduction of dolomite by ferrosilicon and the carbothermic reduction of magnesium oxide are endothermic, require high temperatures, and present serious problems with respect to materials of construction. Because of its apparent simplicity and other advantages, the Bureau of Mines has briefly investigated the reduction of magnesium chloride by calcium carbide. Published data on the reduction of magnesium chloride by calcium carbide are meager. Matignon states that reduction is fairly rapid at 1,200º C. Matsuura claims that magnesium chloride is not reduced by calcium carbide at atmospheric pressure and 800º C; however, by keeping the pressure under 10 mm. of mercury he was able to obtain small globules of magnesium at 800º C.

Mar 1, 1947

By John J. Henn

Two lime sinter processes for recovering alumina from clay, the double-leach process and the single-leach process, are evaluated in this Bureau of Mines report. In both processes, clay and limestone are mixed and sintered to form calcium aluminate from which alumina is extracted as sodium aluminate by leaching with a dilute solution of sodium carbonate. The pregnant liquor is desilicated, then carbonated to precipitate alumina trihydrate which is recovered and calcined to a,-alumina. The fixed capital costs for plants producing 1,000 tons per day of alumina are $85 million for the double-leach process and $86 million for the single-leach process based on a Marshall and Stevens chemical equipment index of 240.0. Because plant locations are variable with respect to the proximity of clay and limestone deposits, a nomograph is included to determine operating costs at various delivered costs of clay and limestone. For plants at which the delivered cost of clay containing 30 percent A1203 is $2 per ton and the delivered cost of limestone is $1 per ton, the operating costs are $81.04 and $89.87 per ton of alumina for the double-leach process and single-leach pro-cess, respectively.

Jan 1, 1969

By Kathleen Kowalski-Trakofler, Edward Barrett

Problem: It is estimated that 5 to 10 arc flash explosions occur in electric equipment every day in the United States. In the mining industry the largest single injury category of electrical injuries are caused by non-contact electrical arcs. Method: This investigation progressed in two phases: (a) 836 Mine Safety and Health Administration (MSHA) reports of electric arcing incidents that occurred over a period of 11 years were reviewed, and (b) personal interviews were conducted with 32 individuals. A theoretical Safe Job Performance Model guided the study. Results: Behavioral dimensions were identified and included the effect of worker experience, judgment and decision-making ability, behavioral and organizational controls, and safety culture. Summary: The National Institute for Occupational Safety and Health (NIOSH) conducted an investigation of behavioral components associated with arc flash incidents and developed recommendations for interventions based on findings. Impact on Industry: This study fills a vacuum in electrical training with a focus on the organizational and behavioral aspects of arc flash incidents. There search is cross-cutting in its scope, in that the results apply not only to mining and construction, but many other industries employing electricians. Although the majority of mine electrical injuries are the results of burns from electrical arcs, few miners are aware that such a hazard exists. A safety training program, which includes a video and an instructor's discussion guide, was developed for electricians based on this study's findings. “Arc Flash Awareness” was released in 2007 (DHHS NIOSH PublicationNo.2007-116D) and is available through1-800 CDC-INFO. Phone:1-800232-4636 or email cdcinfo@cdc.gov. It is also available from MSHA at MSHADistribution@dol.gov or 304-256-3257 (DVD-576). Private industry is producing Portuguese and Spanish language translations.

By S. Gallagher, C. A. Hamrick, A. G. Mayton, R Sonier, R. L. Unger

Introduction Industrial safety professionals recognize that adequate illumination is essential to a safe and productive work environment. The need for effective, lighting in underground coal mines is even greater.1 Designing appropriate lighting systems for these mines is no easy [ ] task because of the unique environment and work procedures encountered in underground coal-mining operations. Miners must depend totally on artificial lighting systems to see. Moreover, the working face is a low-reflectivity and low-contrast environment and is continually advancing or retreating.2 Laboratory mock-ups have been a major part of the process lighting equipment manufacturers must under- go to design an underground machine-mounted lighting system. The mock-ups often have taken considerable time. Furthermore, modifications to a lighting system (using different luminaires with an existing configuration or changing a luminaire's location, orientation, etc.) could require more time with additional mock-ups and laboratory measurements. Understanding the need to improve this situation, the US Bureau of Mines has developed an alternate method for facilitating lighting system mock-ups. A PC-Program (CAP),* with the latest software technology enables users to design, alter, and evaluate under- ground machine-mounted illumination systems. Lux levels and distance are measured as the luminaire is moved incrementally through angular traverses about horizontal and vertical axes. The measurements and angles subsequently are entered into the model. From this input data, three-dimensional isolux or isofootcandle profiles are constructed for luminaires that can be placed at various locations and orientations on a mining machine. As an example, Figure 1 shows a computer display of 21.5 Ix or 2.00 fc profiles for luminaires mounted on a simulated mine-shuttle car. Using this information, the model allows the user to determine the lux level at different locations in space about the shuttle car. How the model calculates illumination During initial development of the CAP model, the isolux profile of the luminaire was determined using the inverse square law (ISL) .3 The method of gathering data comprised recording a single measurement of distance at 21.5 ± 1.21x (2.00 ±11 fc) for angular traverses following 0.09 rad (5 degree) increments. This data was then used to find the illumination in space for any other distance at a given azimuth and elevation using the ISL. Limitations, however, exist with this method.4 The main one is that the ISL assumes a luminaire is a single point source of light, so long as the distance is greater than five times the 1al;gest dimension of the luminous area of the luminaire.5 Also, by using a single measurement to calculate the illumination for a given luminaire in the CAP model a large error could result from an inaccurate measurement.

By David Hoadley, Kenneth R. Maser, Ashok B. Boghani, James E. Billar, D. Randolph Berry, Mackenzie Burnett, Robert H. Trent

D. 1 Most Effective Salts A. Ammonium Phosphates Monammomium phosphate and diammonium phosphate (salts of ortho phosphoric acid) are superior to the triammonium salt in fire-resisting properties. Of these two, the monammomium salt is chemically the more stable. It is also held very retentively by a number of woods, thus reducing leaching out of the salt if exposed to water. Saturated aqueous solutions of mon- or di-ammonium phosphates have vapor preservatives corresponding to an atmospheric relative humidity of 9Z to 93 percent, the wood, will, therefore, not attract any moisture at humidities below this figure. Low concentrations (1 lb dry fire-retardant per cubic foot of the dry, treated timber) will stop flame and high concentration (5 lbs. per cubic foot) will prevent smoldering. B. Ammonium Sulphate In low concentrations ammonium sulphate has only a small effect on flame propagation, but its effect is marked when concentrations of the order of 20 percent are employed. It has no appreciable effect on smoldering. It is more corrosive to metals than are the phosphates, but is less corrosive than ammonium chloride or magnesium chloride. It is possible to leach it out of wood by prolonged and continuous action of water The vapor pressure of the saturated solution corresponds to 81 percent atmospheric humidity.

Jan 1, 1976

By C. M. K. Boldt

Between 1989 and 1991, the greatest number of accidents in surface coal and metal/nonmetal mines involved haulage trucks. In 1995, the most frequently cited factor contributing to the 100 fatalities in these mines was powered haulage. In 1996, over 50% of the 84 Fatalities in mining that year were in surface mining. Because some of the world's largest mobile equipment is used in surface mines, and this equipment is involved in so many accidents and fatalities, new technologies are needed to alert truck drivers and people in spaces around the truck to the possibilities of collisions.

Jan 1, 1999

By Foster Fraas

A method is presented for the linear evaluation of adsorption data using the equations dC = Ae-rv dv and v = [jT] - q, where dC is the phase composition increment, v a calculated parameter, T the absolute temperature, and A, r, h, g, and q the constants. The value of v is calculated from the composition C for both the adsorption surface and the immersion phase. A plot of v for each phase on Cartesian coordinates results in straight line graphs. With temperature variation, a plot of v versus,[ ] also results in straight line graphs. The equations are applicable to electronic and salt equilibria.

Jan 1, 1962

By M. J. Brevoort

Research work in the Bureau of Mines cryogenic laboratory requires the use of high-sensitivity galvanometers of the d'Arsonval type in a building that is subject to unusually severe vibrations. A modified form of the galvanometer suspension described by Julius' has damped the vibrations so successfully that a short note concerning it is thought to be desirable. The laboratory is on the site of the Amarillo helium plant near a building that houses gas engines of from 180 to 250 hp driving compressors and electric generators. The distances from the galvanometers to the individual engines range from about 80 to 180 feet. The subsoil, consisting of black clay loam, transmits the impulses without much damping. The usual methods of protecting galvanometers from vibration were tried and proved fruitless. A Julius suspension purchased on the market was carefully installed in the hope that it would overcome the difficulty, but the conditions were too severe even for this elaborate arrangement. Several modifications of the original Julius suspension, which were then introduced, resulted in almost complete elimination of all vibrational effects. These modifications were suggested by careful study of the original idea embraced in the Julius construction. They were designed to give further constraint to motion in any direction other than that parallel to a line from the point of support through the center of gravity of the suspension, This was accomplished by making the suspended frame more rigid and by improving the means of adjusting each of the supporting wires to the same degree, thereby transmitting any impulse symmetrically through the three wires. The result was a suspension that is more effective, particularly for severe vibration, than the form described by Julius; also, it is believed to have advantages in stability, simplicity, and ease of adjustment over the few suspensions for this type of service that the author has found described in the literature.

Jan 1, 1931

By Kenneth J. Miller

The Bureau of Mines conducted an investigation to improve the flotation response of coals that are difficult to wash by froth flotation. A literature survey and experimentation showed that, for the most part, refractory coals can be floated with oily collectors and frothers. Collector reagent consumption can be minimized and the selectivity of the flotation enhanced by assuring adequate, but not prolonged, reagent conditioning. Where flotation selectivity is especially poor, two-stage rougher-cleaner flotation is recommended. It was concluded that a major problem with refractory coals is predicting when they will appear in a flotation circuit so that supplementary flotation collectors can be added. Coal losses due to variation in the floatability of the feed might be reduced if a nonpolar collector such as kerosine or fuel oil is used along with a frother as general coal flotation practice.

Jan 1, 1977

By T. M. Garland

This report presents a Bureau of Mines assessment of crude oil and associated gas production and reserves that would result from different drilling efforts in the lower or contiguous 48 States during the 1972-85 period. The drilling effort was based upon five growth rate assumptions from the 1971 level. Additions to crude oil reserves were computed for nine cases resulting from the use of three equations for findings per foot drilled and three constant revision factors. The results indicate that the United States will not become self-sufficient in crude oil production by 1985 and also illustrate the lead time required to reverse the decline in oil production. Discussion is limited to three of the nine cases to provide high, intermediate, and low results. More emphasis is on the intermediate case because it is indicative of the most probable trends. The methodology and statistical data are included in the appendices.

Jan 1, 1974

By J. Walden, J. Rhoades, R. E. Miller, R. Gibbs, P. Boman

Accelerometers and pressure transducers, mounted in suspension components, can be used to monitor the ride of haulage trucks. Presently, it is difficult to tell what caused a jolt to the truck using either pressure or acceleration data alone. When information from a global positioning system (GPS) is recorded at the same time as shock pressures or acceleration data, the exact location of an event can be determined. Mine management can then determine what caused the jolt to the truck. This research is part of a National Institute for Occupational Safety and Health (NIOSH) project called "Engineering controls for reduction of jolting/jarring injuries in surface mines." NIOSH is investigating how the work environment of haulage truck drivers can be improved. The US Mine Safety and Health Administration (MSHA) notes that, between 1986 and 1995, 60% of the back injuries were to haulage truck drivers in metal/nonmetal surface mining. Personnel from Phelps Dodge suggested that combining acceleration data with information obtained from a GPS could generate results with a variety of uses. Therefore, researchers at the Spokane Research Laboratory (SRL) began investigating how to tie acceleration and GPS data together. It was originally thought that this tool would be used primarily for road and truck maintenance. However, as research progressed, it became apparent that it would also be useful in providing feedback about equipment operations and identifying unusual causes of jolting. Experimental approach Available components that function well by themselves were linked for the purpose of proof of concept. Using a Modular Mining Systems (MMS) product called Vital Signs, SRL researchers took an Aero-Marine Products (AMP) acceleration recorder and hardwired it to MMS Dispatch equipment already installed on a truck. AMP is one of several manufacturers of acceleration recorders frequently used to monitor freight during shipping. MMS Dispatch is used for production accounting and truck dispatching and uses GPS tracking. Through Vital Signs, an analog or digital alarm signal can be recorded. Steve Rhoades, of MMS, wrote unique code that links the Vitals Signs data and GPS location and stores this data in an ASCII log file. SRL researchers installed the equipment in a Caterpillar 793 haul truck. The result was a working prototype. Figures 1 and 2 show the instrument installation in the truck. Discussion From 8:30 pm on Sept. 14, 1998 until 6:50 am on Sept. 15 1998, 899 jolts above a threshold of 2 g (1 g is the acceleration of gravity. It is either 9.81 m/s2 or 32.17 ft/ s2.) were measured on the test truck. Some sections of the haulage road produced most of the events, while

By George J. Conroy, Angel G. Jordan, Eugene W. Bartel

Time-domain reflectometry has long been an accepted and used method for locating electrical faults in electrical cables. The process has, however, required the use of equipment that is somewhat complex and difficult to use. The skill level needed to operate such equipment is high. Therefore, the use of the time-domain reflectometry process has been limited to selected locations and controlled environments. The process, however, has great potential for mine system applications. The ability to locate and repair trailing power cable without removing it from the mine would result in great savings in cost and employee-hours. Therefore, an automatic microprocessor-controlled time- domain reflectometry system was developed to reduce process complexity and skill level needed to operate the unit. The theory of operations is discussed along with the computer analogies used in the unit. The present unit capabilities are presented and future areas of application and research are discussed.

Jan 1, 1979

The Ringelmann Smoke Chart fulfills an important need in smoke abatement work and in certain problems in the combustion of fuels. A knowledge of its history and method of preparation is, therefore, of interest to many. Since instructions on its use are not shown on the recent edition of the chart, those included in this revision of the previous Bureau of Mines publication now are a necessary complement to the chart. More detail regarding the use of the chart is included than was given in the earlier version.

By A. E. Raddatz

The Bureau of Mines has determined the electrochemical rate of anodic dissolution of vanadium metal in a VC12-VC13-NaC1 electrolyte at 860' C for the purpose of elucidating the reaction mechanism. Rate measurements were carried out with the help of specially designed equipment capable of continuously recording the weight loss experienced by a cylindrical vanadium anode immersed in the molten salt electrolyte while a constant current is maintained through it. The rate is expressed as a function of current density and VC13 concentration, and the reaction is interpreted in terms of an adsorption mechanism. Multiple regression analysis of the data gave the following rate equation: Rate x 104 (g.cm-2.sec-1) = -0.38 + 2.64 current density (amp-cm-2) + 0.69 log, (mole-percent VC13).

Jan 1, 1974

By M. A. Mahtab

This report presents a new procedure for analyzing the orientations of rock fractures in an engineering site. This procedure, coded in a computer program, identifies clusters or groupings among the fracture orientations and calculates (1) the mean orientation of the fractures within each cluster and (2) the dispersion or scatter among these fracture orientations. Data points are represented by intersections of joint normals with the upper hemisphere, which is divided into 100 equal-area quadrilateral patches. The points in adjacent patches where the Poisson distribution test shows significant concentrations are assigned to a single cluster. For a cluster whose fracture orientations follow Arnold's hemispherical normal distribution, a confidence interval for the fracture orientation mean is calculated by applying Fisher's estimates. The technique is applied to the treatment of three examples.

Jan 1, 1972

By Ivor Hawkes

This report describes how longitudinal and bending stress waves in' percussive drill rods generate noise. It is shown that in practical drills the largest noise source is the bending waves, which are mainly generated because of imperfections in the piston, chuck, and drill rod alignment. Equations are presented which enable the noise spectra generated by the bending and longitudinal waves to be precisely predicted. Means for reducing the amplitude of the bending waves are discussed.

Jan 1, 1977

By Ren G. Dong, John Z. Wu, Daniel E. Welcome, Kristine Krajnak

Although the exact mechanisms underlying vibration white finger (VWF) are not clear, it has been speculated that VWF is associated with variations of the blood flow patterns due to the physical damage and/or degeneration in neural and vascular tissue caused by vibration loading [1]. Excessive dynamic deformation of the soft tissues in the fingertip under vibration loading is believed to induce multiple occupation-related hand/finger disorders. However, the in vivo distributions of the dynamic stress/strain of the tissues in the fingertip under vibration conditions have not been studied because they cannot be measured experimentally to date. The goal of this study is to analyze, theoretically, the location and frequency-dependent dynamic deformation of the soft tissue in the fingertip during vibration exposures. [ ] Methods The fingertip considered in the model is the distal phalanx, the portion from the distal end of the fingertip to the distal interphalangeal (DIP) joint articulation (Fig. 1). The external shape of the fingertip was determined using a smooth mathematical surface fitting to the observed fingertip shapes. The fingertip surface was then scaled to the dimensions of a typical male index finger: length 25 mm, width 20 mm, and height 18 mm. The fingertip was approximated to be symmetric, such that only a half of the fingertip was considered in the FE modeling. The fingertip was assumed to be composed of outer and inner skin layers, subcutaneous tissue, bone, and nail. The soft tissues (inner skin layer and subcutaneous tissues) were assumed to be nonlinearly elastic and viscoelastic, while the bone, nail, and outer skin layer were considered as linearly elastic. The simulations were conducted using a displacement-controlled protocol in two stages. First, the fingertip was statically pre-compressed. The contact plate was first displaced towards the finger to achieve a predetermined value of tissue deformation (i.e., 0.5, 1.0, 1.5, and 2.0 mm). Second, the steady-state dynamics responses of the fingertip were analyzed using a linear perturbation procedure. The fingertip was subjected to a continuous harmonic excitation (magnitude 0.5 mm) from the contact interface. The dynamic analysis was performed in a frequency domain ranging from 16 to 2000 Hz. The frequency-dependent distributions of the vibration magnitude and dynamic strain magnitudes in the soft tissues are investigated. Results Typical simulation results for the frequency-dependent distributions of the vibration magnitude in the soft tissues are shown in Fig. 2 (figures show the results with a pre-compression of 2.0 mm). The vibration magnitude at the contact surface is 0.5 mm (specified) for all frequencies, while the vibration magnitudes in the soft tissues are location- and frequency-dependent. It is clear that the fingertip has a major resonance around 125 Hz, at which the vibration magnitudes in the soft tissues are over four times greater than that of the contact plate (0.5 mm). It is interesting to observe that, at this resonant frequency (125 Hz), the soft tissues at the tip has the maximal vibration magnitude while the regions near the contact

Jan 6, 2006

By Wilbur I. Duvall

Nineteen quarry blasts were instrumented with particle-velocity gages mounted in a uniform soil overburden, back of one face in a quarry in Iowa. Three components of particle velocity, radial, vertical, and transverse, were recorded at each of eight stations back of each blast. Distances from blast area to gage stations ranged from 150 to 3,000 feet. Eleven of the quarry blasts employed millisecond delays, and eight were instantaneous blasts. Charge weight per hole was 200 pounds, and the charge weight per delay interval, including the instantaneous blasts, ranged from 100 to 3,000 pounds. Analysis of the data from these tests shows that the particle velocity, V, produced at distance, D, by a quarry blast of charge per delay interval, W, can be represented by an equation of the form, V=KWb D-n, where b and n are exponents, and K is the intercept constant which is a measure of the level of vibration. The value of K for a millisecond-delayed blast employing one hole per delay interval is about 42 percent larger than the value of K for a single-hole blast. The value of K for a multiple-hole milli-second-delayed blast is about the same as that for an instantaneous blast when the charge per delay for the millisecond blast is equal to the total charge for the instanteneous blast. The vibration level from millisecond-delayed blasts employing one hole per delay is shown to be independent of the length of the delay interval and the number of delay intervals over the range of the variables tested: 9, 17, and 34 milliseconds and 3, 7, and 15 delays per blast.

Jan 1, 1963