Search Documents

By W. C. McLaughlin

Under a cooperative agreement, the Bureau of Mines, Magma Copper Co., and ASARCO, Inc., tested backfilled ground support systems at t.wo elevations in Magma's San Manuel, AZ, mine. The tests were mainly for guidance in designing the loading crosscuts of the new ASARCO Sacaton underground mine. Two-piece, wide-flange steel sets for 8-by 8-ft (2.44-by 2.44-m) and 11-by II-ft (3.36-by 3.36-m) openings were designed. Set spacing was 3 ft (0.91 m) and 5 ft (1.52 m), respectively. After erection, the sets were lagged with various test materials. The void between the lining and the ground was backfilled with sand and pea gravel. Instruments measuring strain (used to determine changes in stress) were placed beneath the sets and in the backfill. Results indicate the backfilled sets in the smaller drift (2315 grizzly level, panels 6 and 7) of 8-by 8-ft (2.44-by 2.44-m) cross section are a viable permanent support system, lower in cost than the standard formed concrete. Results are inconclusive in 2615 grizzly level, panels 5 and 6, where wide-flange steel sets were used with 5-ft (1.52-m) long concrete gob lagging of T-design.

Jan 1, 1983

By J. P. Walsted

Offgrade chromite concentrate, with a Cr-Fe ratio of 1.3 to 1.4 has been successfully smelted to produce useful ferroalloys. The Cr-Fe ratio is not improved, but the alloys can be used without a too drastic change in normal steel-mill practice. The ordinary high-carbon ferrochrome has been successfully produced by smelting under highly acid smelting conditions. An alloy containing 50 percent chromium was produced at a power consumption of 4,490 kw.-hr. per ton of alloy. Alloys containing 20 percent silicon were made by direct smelting chromite concentrate and silica.

Jan 1, 1956

By Ann G. Kim

Studies on the initiation and propagation of mine fires have dealt almost exclusively with coal. It has been assumed that the self-heating potential of carbonaceous shales and coal wastes is relatively low. However, in abandoned coal mines and waste banks, initiation and propagation of fires may be strongly dependent on the self-heating tendency of these materials. The purpose of this study was to compare the self-heating probability of carbonaceous shales and coal wastes to that of coals. This study utilized a modified differential thermal analysis method, in which the combustion furnace temperature was the reference to which the sample temperature was compared. Based on the distribution of the maximum temperature differential and the sample heating rate, a self-heating probability value (SHPV) was calculated that corresponded to observed self-heating behavior. In this study, several of the carbonaceous shales and one coal waste had relatively high SHPV. The SHPV did not correspond directly to heating values or to differences in sulfur concentration.

Jan 1, 2010

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By B. C. Parks

This paper is a report on the relationships between petrographic composition, chemical composition, physical properties, and thermal behavior of banded bituminous coal. It describes the relationships between petrographic composition, behavior in various laboratory tests, and carbonizing properties of different petrographic types of coal that occur in relatively thick benches in a single bed of high-volatile A bituminous coal - the Hernshaw bed of Boone County, W. Va. Thin-section microscopic analysis and free-swelling index determinations of the thin-section samples were made of a standard column sample. A standard face sample, a representative channel sample, and representative samples of two prominent petrographic benches of bright and dull coal were subjected to chemical analyses and free-swelling-index, plasticity, dilation, agglutinating, low-temperature carbonization, and BM-AGA retort tests. A float-and-sink separation was also made of part of the standard face sample. The fractions from this gravity separation were subjected to petrographic and chemical analysis and free-swelling-index, plasticity, and dilatation tests.

Jan 1, 1959

[lllc purpabr at thla report Vd, Lu JeLermlnr the health ar1J sdfet?; Nene11Le a octatc?J ultll Lne oar L.t support Ydlll ..up.I,ated lu dltetllative cupPurt svsLem, larrellLty hcle.g uaeJ af the Len,::rat 1, UI.Jlng 11-al tl. .1 a d 1 c L V h S LIdl'. L dal. I -ten- lu L he tt I .. L'., etuJ I e. 11'? L_1,1'1,11 .Jtd.. it, ..urn,at'l core ,LuJICCill JhLdll, an.: ...,La -IL .utia_tel .an LI?r oar of -l: l,.!rl .a..a. Ma terI.I auJ ...11,mc[Ii -ldla,tutcle 11. LI.ac .uwIttIca Welt a, a.. V.alte,, L.. .:Ltail, ..,,L., uI. LuClu,alug) Lelll anci ur devel?puJ I.,r Cul r1 , all. ...~.,rLrI Vt,ILt 1.'ere ~e,1C L? .Lher Gentiaii m111cc t, UL.-rye a Variety o. a rL vyl I pp.1Ca:t..n:. 'a.la IrL ..,_wLeiti, Iapl,.III ,tall ~,..:. IL all, maLertdl c1,arait-erlstIcs, JIRICn,IUIIe. and laden ul1.1 ILc rrgatrelaeuls. ,1 r.? p.'rt .a pro-1Jd, labor rep altrlarnts Jdta and illtlitI ieS tie l,ealtll d?J ,atetV ISSUC ,u-1aled Wit su furl Wall a an, CJl,wttuctSOn, I'aLentiaI appll.at1ou:. Ior support Walt, ,a,. , a, sdV.u,L111 .., u.1 retreating lungval1, single -t r-, roar al,- pi r. [,-+ln, anJ SuhIU..,Ina, Sill] b1OpplllgL ale 1:111neated aid al? e.aIWRac AS Sddemcni LV pre,C'IIL..: .,f LI. Clabllhty r+t rlul,I.,y111I? ulg4,rt .I Le.l,lwlug,. Lr i,,,rCASC Lllc rtCVLLrS rat, u., retrc.+tlnp .unui.,11? ur L., elply, A d v Ctnp IuI-,wall in uer;-!y iy1ng seam, . 11111.a1L .a1,.'iI1.-I,.. nr S.IU1tIVlil a1 milItlI; Lust, La LIldnt;2S L.~ gey support Vait Id tdmcLera la dlaa presents,.]

Jan 1, 1980

By Leroy Dockter

The grinding characteristics of lignite in a ball mill were investigated. The variables studied were initial lignite moisture content, degree of in-the-mill drying, and lignite source. The mill tested was a pilot-p1ant-size conical ball mill which had a maximum output of from 80 to 180 lb/hr pulverized product depending on the lignite and test conditions. The capacity of the test mill ranged from 82 to 103 lb/hr depending upon mine source, in pulverization of as-mined lignite with minimum drying, The capabilities of the ball mill could not be correlated to Hardgrove index of the individual lignites or other observed physical properties. Predrying lignite from its 35 to 40 percent raw moisture content to about 10 percent moisture before grinding improved the mill capacity 87 percent, compared to an increase in capacity of 74 percent with in-the-mi11 drying to the same product moisture.

Jan 1, 1967

By F. D. Everett

Thermoelectric and metal alloying applications have changed the status of tellurium from oversupply to under supply . In a search for new sources of this element in Arizona , Colorado , New Mexico , Utah , and neighboring states , the Bureau of Mines analyzed more than 200 samples and obtained the results of tellurium determinations by private companies on more than 500 samples from a wide variety of mineral - bearing deposits . The About 40 minerals containing tellurium have been reported , mainly tellu- rides of gold , silver , bismuth , mercury , lead , copper , iron , and nickel . minerals usually occur in small quantities and identification in ores is extremely difficult . Samples containing more than 0.1 percent tellurium were taken from the Hilltop and Memphis properties in Dona Ana County , N. Mex . , and the Silver King property in White Pine County , Nev . , where development was chiefly for base metals . The Lone Pine mine in Catron County , N. Mex . , and the Bambolla mine near Moctezuma , Sonora , Mexico are potential sources of native tellurium occurring in small but high- grade pods . Much of the production of tellurium has come as a byproduct of electro- lytic refining of copper and lead- zinc ores in Arizona , Colorado , New Mexico , and Utah . Base -metal ore deposits will continue to be the most important pri- mary source of tellurium , although the concentration in ores is nearly always less than 10 parts per million . Any significant increase in output of tellu- rium probably will be related to production and improved efficiency in smelt- ing and refining base - metal ores .

Jan 1, 1964

By Brian R. Zelenka

The Bureau of Mines (Bureau) reviewed all available information regarding geologic and depositional processes contributing to potential coastal and offshore platinum group metal (PGM) placer deposits around the Goodnews Bay Mining District. The Bureau found that favorable environments for PGM along with gold and chromite enrichment include: (1) buried paleofluvial channels; (2) recent paleofluvial channels with little marine sediment overburden, (3) beach deposits, particularly in the upper swash zone and near back beach environments; (4) paleostrand lines; (5) shoal lag deposits inside the mouths of Goodnews and Chagvan bays; and (6) bases of far offshore tidal ridges which may represent reworked glacial deposits. Limited geologic and compositional (assay) data prevent determination of deposit size and grade of PGM mineralization for each deposit class. Future geologic sampling requirements for demonstration of identifiable offshore and beach PGM-bearing placers are discussed. Beach and offshore sampling programs conducted by the Bureau in 1986 will contribute additional information providing verification of specific deposit classes.

Jan 1, 2011

By H. William Zeller

The U.S. Bureau of Mines evaluated the effects of two iron-based fuel additives on diesel particulate matter (DPM) emissions. The 5.6-L, six-cylinder test engine is typical of engines used in underground mines. One additive, ferrous picrate, did not measurably affect exhaust emissions. This report is mainly about a ferrocene-based additive that reduced DPM between 4 and 45 pet., depending on engine operating conditions. The report concludes that the DPM reductions were caused by the catalytic oxidation properties of a ferric oxide coating that developed inside the engine's combustion chamber. The ferric oxide coating also decreased gas-phase hydrocarbons and O2, but it increased CO2 and NOx, The increase in NOx, of about 12 pet, is considered the only adverse effect of the ferrocene-based fuel additive. The results suggest that the effectiveness of ferrocene was partially offset by increased sulfates because of the high-sulfur fuel used. Recommendations for continuing fuel additive research are presented.

Jan 1, 2010

By John A. Breslin

This report summarizes the principal activities and significant results of the Bureau of Mines respirable dust research program since passage of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Mine Safety and Health Amendments Act of 1977. This program has investigated new and improved techniques and equipment to reduce or prevent the formation of dust during the cutting cycle; to dilute, suppress, or collect airborne dust generated during mining, handling, and processing; and to improve the measurement of dust levels for evaluation of engineering controls and for enforcement of Federal dust standards. The report is intended for mining industry dust control specialists and other interested parties. It includes a brief summary of the program to date, a section on future research plans and goals, and a list of publications resulting from the Bureau's respirable dust program.

Jan 1, 1982

By J. E. Hamak

This publication contains analyses and related source data for 920 natural gas samples from 26 States and 2 foreign countries. All samples were obtained and analyzed as part of U.S. Bureau of Mines investigations of the occurrences of helium in natural gases of countries with free market economies. This survey has been conducted since 1917. The analyses published herein were made by mass spectrometer and chromatograph.

Jan 1, 1991

By Robert H. Ridgway

This circular outlines salient facts regarding the sulphur industry of the United States and the world. It is founded chiefly upon published information available in the literature of the subject. The Bureau of Mines has in its files additional, more detailed data upon many of the topics presented very briefly here, and will endeavor to assist the mineral industries and the public by giving further information in response to individual inquiries. It will welcome comments, criticisms, and contributions of data that may assist in making later editions of this circular more accurate, or in developing more fully the bureau's mineral files pertaining to sulphur. Throughout this paper sulphur is used to designate crude sulphur or brimstone, not sulphur produced from pyrites or' smelter gases.

Jan 1, 1930

By E. J. Babcock, W. W. Odell

The Bureau of Mines since its establishment has always taken an active interest in the utilization of lignite and in the development of the lignite dep'osits of the United States. Extensive lignite fields occur in the west central States, notably in North Dakota, Montana, Wyoming, Colorado, and Texas; there are smaller areas in several other States, some of which are widely separated. The total area of the deposits and the total amount of lignite in these several districts are so enormous that the economic value is seldom recognized. To the people of ·the west and west central regions, however, the larger utilization of lignite, in whatever form it may be, is of fundamental importance, and any new methods or uses that promise to open these great lignite fields for more general and more efficient use deserve careful study. Although these lignite deposits underlie areas of thousands of square miles, their development and general utilization has been rather slow. This is no doubt partly because many of the districts are not thickly settled or highly developed in manufacturing industries, but is largely because lignites, from their peculiar physical and chemical characteristics, are low-grade fuels. Most of the lignites in these areas are imperfectly developed coals; many have a more or less woody structure; some belong to the brown-coal type; and others are darker, denser, and more homogeneous, approaching subbituminous coal. The people living in the regions in which these vast deposits occur, especially in the west central part of the United States, are vitally interested in every effort toward bettering lignite as fuel and aiding its wider utilization.

Jan 1, 1923

By R. G. Knickerbocker, T. E. Evans, J. L. Morning, D. R. Torgeson, F. W. Wessel

"INTRODUCTION Pilot-plant studies on processes for converting low-grade domestic manganese ore to high-grade oxide or sulfide products by pyrometailurgical process was initiated at the Boulder City, Nev., Experiment Station in 1942. These investigations were given impetus by the possibility of a national shortage of ferro-grade manganese oxide for war needs.The manganese ore employed-in most of the pilot-plant smelting tests was from the manganosiderite-nodule deposits at Chamberlain, S. Dak. This deposit although low-grade, is extensive and represents, the largest reserve of manganese in continental United States. 6/ The Bureau of Mines has recently developed a Carryall mining-conical rolls treatment method that shows promise of making possible economic removal and subsequent beneficiation of the nodule-bearing shales. 7/ Smelting tests were made also on Artillery Peak, Ariz., mill concentrates in the productions of unrefined manganese matte for the steel The pilot-plant smelting program was based upon the fundamental fact that manganese, like copper, will sulfidize and become miscible with FeS. The matte this formed represents the initial smelting step in the pyrometallurgical treatment of the beneficiated ore. The concentrated nodules containing about. 18 percent manganese were smelted with varying amounts of pyrites and appropriate fluxes to produce Mns-FeS mattes containing 16 to 50 percent manganese. When the manganese and iron was completely sulfidized, the mattes contained 16 to 23 percent manganese. Reducing the pyrite resulted, of course, in the selective sulfidization of manganese and the production of a matte containing a correspondingly higher ratio of MnS to FeS. Complete sulfidization smelting produced slags of lower manganese content and hence resulted in higher manganese recoveries in the matte."

Sep 1, 1946

By James Westfield

This report covers the calendar year 1953 and has been prepared and submitted in accordance with the provisions of Sec. 106(a) and Sec. 212(c) of the Federal Coal Mine Safety Act (66 Stat. 692; 30 U.S.C. Secs. 451-483). During this first full calendar year of operations under the Federal Coal Mine Safety Act, the coal-mining industry of the United States attained the best injury records in its history - improving the former best records (made in 1952) by 91 fatal and 10,020 nonfatal injuries. Whereas, the mandatory provisions of the act were intended and designed to prevent major mine disasters, apparently the effects have reached beyond the scope thereof in reducing mine accidents generally.

Jan 1, 1954

By H. S. Martin

This paper, describing the concentrating practices at the plants of the Utah Copper Co., is one of a series being prepared by the United States Bureau of Mines in which the data are given in as nearly uniform c manner as possible. The Magna mill is 19 miles west of Salt Lake City on the routes of the Lincoln and Victory highways, and the Arthur plant is 1 mile west of the Magna mill. Both are on the main road west of the town of Magna and east of the town of Garfield.

Jan 1, 1931

By D. G. Willard

The U.S. Department of Interior, Bureau of Mines has evaluated the potential resource and annual availability of cobalt from 27 deposits or districts in 11 market-economy countries. More than 95 pct of primary cobalt production from market-economy countries, mainly byproduct output from copper and nickel operations, was analyzed. Approximately 1,200,000 mt of cobalt is potentially recoverable at the demonstrated resource level. Very large additional resources exist, especially in laterite deposits, but are at the inferred level. The producing operations evaluated in this study are expected to produce about 19,000 mt of cobalt in 1989, significantly less than the available capacity of about 31,000 mt. More than 14,000 mt per year of cobalt is produced from copper-cobalt deposits in Zaire and Zambia, of which 11,000 mt can be produced at a copper price of $O.60jlb or less with a O-pct discounted cash-flow rate of return (DCFROR). Approximately 4,400 mt of cobalt is produced annually from nickel-cobalt deposits in six countries, of which about 1,800 mt (in Canada and Brazil) could be produced at a nickel price of $1.50jlb or less at a D-pct DCFROR. Approximately 200 mt per year of cobalt is produced from a cobalt mine in Morocco. Most of the evaluated nonproducing operations and prospects that could potentially produce cobalt as a principal product or byproduct would require a total cost (including a 15 pct-DCFROR) significantly exceeding January, 1989 market prices of the principal commodities. Principal-commodity dependence, transportation routes, cobalt toxicity, and other issues that could affect the availability of cobalt are addressed herein.

Jan 1, 1991

By A. E. Back

[Several processes for recovering manganese from low-grade ores have been proposed3/4/5/ in which an aqueous slurry of the ore is leached with gas containing nitrogen, oxygen, and sulfur dioxide as obtained from burning sulfur or roasting sulfide ores. The manganese dioxide is dissolved, and most of the sulfur dioxide is oxidized to sulfate, but an appreciable quantity of dithionate is usually formed, together with acid from oxidation of the sulfur dioxide. The over-all reactions may be represented as follows: (1) Mn02 + S02 = Mn++ + S04--. (2) Mn02 + 2S02 = Mn++ +S206--. (3) H20 + So2 + 1/2 02 = 2H+ 5S4--. (4) H20 + 2S02 + 1/2 02 = 2H+ + S206---.]

Jan 1, 1952

By R. A. Hatch

The United States depends mainly on foreign imports, principally India, for an adequate supply of sheet mica suitable for its many uses in the electrical and electronics industries. Sheet mica has, in fact, played an indispensable role in developing these industries,4/ and, in turn, the products of these industries (radio, radar, electric motors, and many others) have become indispensable to the military forces. Because or these conditions, sheet mica in its better qualities long has been classified as a strategic and critical material, and from this stems the wide-spread interest in substitute materials of which synthetic mica is one potential type. The United States Departments of the Navy and the Army entered into a cooperative agreement with the Bureau of Mines in 1947 to study ways and means of synthe-sizing and growing mica crystals. This is one of a series of reports5/ that describe the results of this program.

Jan 1, 1956