Search Documents

Reduce the hazards to which mine personnel are exposed by providing safer procedures for removing dragline wire rope terminations. Background The termination points of wire ropes used on draglines consist of a wedge and socket that lock the rope in place through friction. These components must be separated when the wire rope is changed. At present, the cannon method is the most common procedure used to accomplish this. However this method, using a small cannon and primer (detonator) cord to propel a steel projectile that will knock the wedge out of the socket, has the potential of causing injuries to mine personnel and damage to equipment. The Bureau of Mines, has devised safer, and equally efficient methods of removing wire rope terminations. The Bureau began by studying the cannon method, its merits and draw-backs. Safety guidelines were then developed for the cannon method, and two alternative methods-the pendulum ram and hydraulic pusher-were devised and tested. The Cannon Method The steel projectile used to separate the wedge and socket in the cannon method was found to be very effective. However, the method poses the inherent hazards of any explosive de-vice-hazards that could be increased by lax work procedures. There is no strict uniformity in the manufacture of the cannon or in the work procedures used in the mines employing it. Hazards could be reduced, or even eliminated, with adaption of certain manufacturing and work-procedure guidelines, such as 1) making the cannon and projectile de-signs, as well the work procedures used, uniform, 2) ensuring separate loading of the charge and detonator with insertion of the detonator through a separate port, 3) connecting electrical firing circuits only after the charge and projectile are loaded and the cannon is placed in its final firing position, 4) using approved detonating devices, 5) anchoring the cannon before firing and, 6) placing armor netting over the cannon before detonation.

Jan 1, 1986

By C. B. Manula, R. L. Sanford, R. A. Rivell

The need for a large capacity, high speed computer is more apparent in the revised model than in the original one. Core storage requirements for data and model logic have at least tripled. This dictates the use of one of the large modern machines such as the IBM 360-370 series or the Univac 1108 and 1110, which handle the model without the need for extensive program overlay. Computer time is expensive on these machines, however, and comprehensive analysis has gone into optimizing computer execution time consistent with model information flow sensitivity. For example, revised locomotive tramming routines have been developed which will significantly cut execution time compared to the previous version. Transceiver Applications The computer coding for the model has been developed to enable program execution and testing using a remote terminal on a time sharing system. In fact, nearly all of the coding, debugging, testing and modifications have been performed from a terminal during develop¬ment. The gaming options described in the Model Input Section of this report have been designed so that they are easily changed by the user from any remote site. One restriction on remote applications which could arise, however, is where highly detailed output options are specified, resulting in a large amount of output records which could be handled more efficiently on a high speed printer.

Jan 1, 1974

By Lloyd A. Morley

Proposed advantages and disadvantages of low-voltage shielded trailing cables are formulated utilizing the literature and industry sources. A partial analysis of these proposed advantages and disadvantages is completed through a review of the literature. Cable costs are assembled from mine operators, cable and splice manufacturers, and actual cable purchases. To confirm each advantage and disadvantage, an underground test site is established, and testing is performed here and in the laboratory. All testing procedures are completely described. The results of this investigation are reported and used to formulate recommendations attendant to low-voltage shielded cables. Suggestions for installation, handling, and maintenance are presented.

Jan 1, 1977

By R. E. Lindstrom

Effective separation of rare-earth mixtures is obtained using hydrogen as a retaining ion at 200° F with ethylenediaminetetraacetic acid (EDTA) eluant. Results obtained in Bureau of Mines bench-scale apparatus and large columns with hydrogen as a retaining ion closely parallel those obtained with copper as a retaining ion. The use of hydrogen as a retaining ion permits EDTA and water, collected before rare-earth breakthrough, to be recovered in a form that allows the material to be recycled without extensive processing. With the exception of yttrium and dysprosium, separation of rare-earth mixtures is improved and throughput is increased by elevated temperatures. Separation with 1,2-diaminocyclohexanetetraacetic acid (DCTA) eluant increases markedly on increasing temperature from ambient to 250° F; however, on the basis of separation efficiency, DCTA does not compare favorably with EDTA.

Jan 1, 1962

Aluminum alloys are used in two broad classifications: wrought and cast. Wrought alloy products, which are formed into final shape by rolling, forging, extruding. etc., contain low percentages of alloying elements; whereas cast aluminum products, which generally are not worked before use, may contain higher percentages and a somewhat different selection of alloying elements. For example, wrought aluminum alloys usually contain less than one percent silicon and cast alloys contain as much as 18 per-cent silicon. While there are good techniques available for separating aluminum alloys from mixed scrap, there are no efficient ways to separate wrought aluminum from cast aluminum. The high levels of silicon, iron) copper, and zinc from the cast alloys make wrought-cast mixtures unacceptable for wrought alloy production. Consequently, separated wrought aluminum scrap commands a premium price on the market. Since increasing amounts of mixed aluminum alloys are being recovered from automobile scrap, this separation is important for efficient recycling of these alloys. Approach The difference in thermo-mechanical properties between the two classes of aluminum alloys is used as the basis for the separation process. Casting alloys lose their ductility within a certain temperature range while wrought alloys remain ductile. As temperature increases, aluminum alloys gradually become weaker, and at a certain temperature, each alloy loses strength and ductility due to incipient melting in localized areas. For casting alloys that temperature generally lies between 520° to 560° C, but it is above 600° C for most wrought alloys. Mild crushing, therefore, in the proper temperature range will result in complete fragmentation of the casting alloys but only plastic deformation of the wrought alloys. A simple screening step then is used to separate the oversize wrought pieces from the fragmented cast alloys.

Jan 1, 1984

By Joseph C. Zelanko, Christopher Mark

During August, two eastern Kentucky coal miners died in a roof fall during retreat mining operations. They had just finished extracting one pillar block and were moving to the next one when the intersection they were standing in collapsed. Regrettably, this was not an isolated incident. Since the end of 2000, there have been 28 ground fall fatalities in U.S. coal mines. Of these, 10 occurred during pillar recovery operations. Although pillar recovery has been associated with about one third of recent ground fall fatalities, it accounts for only about 10% of U.S. underground coal production. Statistically, a coal miner engaged in pillar recovery is several times more likely to be killed in a ground fall than a miner on an advancing section of a longwall. Pillar recovery is dangerous because it creates an inherently unstable situation. Once the pillars are extracted, the roof is expected to cave. Safe pillar recovery does not mean preventing roof collapse, it means ensuring that it only occurs after the miners have completed their work and have left the area. Fortunately, there are a number of proven techniques that can greatty reduce the hazards of pillar recovery. These include better mine planning, improved roof support, and safer work procedures. The goal of this article is to describe the most significant "risk factors" associated with pillar recovery, and prescribe control techniques that, taken together, can reduce the overall risk to miners. The conclusions are based on extensive studies conducted by the National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) that have included detailed analysis of every fatal retreat mining incident since 1992 (25 incidents resulting in 30 fatalities). Risk reduction strategies for pillar recovery can be divided into three main groups: Global Stability: Prevention of section- wide pillar failure; Local Stability: Prevention of roof falls in the working area; and Work procedures and worker location: Minimizing exposure to hazardous areas.

By Ira E. Sproat

The question "Why can not American kaolins be substituted for English china clay?" has been asked time and time again, and more often since the beginning of the present war in Europe, which has threatened to cut off the supply of European clays imported from abroad. The answer to this question has invariably been, that the domestic kaolins are not as pure and uniform in composition as the imported clays. This demand for white-burning American clays is of such economic importance that it was considered advisable to determine whether some of our vast deposits of impure white clays could not be refined sufficiently to permit their being substituted for the foreign materials. Up to the present time mechanical principles only have been applied in the refining of kaolins, but in order to keep pace with the increasing requirements for better quality and uniformity of product, the application of the principles of colloidal chemistry is necessary. The investigation described in this report was carried on to deter- mine the practicability of applying technical control of clay disperse systems to the refining of kaolins and the utilization of the prepared clay in the manufacture of vitreous china and wall tile. It is hoped that this report will prove a stimulus to the clay- washing industry; will point out a method of refining certain Amer- ican clays, and will lead to the substitution of domestic kaolins for imported china clays by manufacturers of high-grade ceramic wares.

Jan 1, 1916

By Robert M. Becker

A thick-wall cylinder solution applicable to the evaluation of anisotropic elastic parameters is derived for the interpretation of stress relief data. For a restricted class of problems, a special relationship among certain orthotropic moduli yields stress distributions for the plane orthotropic problem that are identical to the corresponding isotropic case. A ring or hollow cylinder with these specialized anisotropic properties subjected to uniform radial loads is one of the problems in this class. Consequently, known stress solutions are used to develop the strains and displacements for a specialized orthotropic thick-wall cylinder under uniform pressures. The results are consistent with anisotropic equations used in the evaluation of in situ rock stresses.

Jan 1, 1968

By D. R. Babich, E. R. Bauer

The U.S. National Institute for Occupational Safety and Health (NIOSH) is conducting a cross-sectional survey of equipment sound levels and worker noise exposures in the stone/aggregate mining industry. Six stone/aggregate mines (three surface and three underground) were recently surveyed, and the findings (ire presented here. The surveys consisted of sound-level measurements conducted around various equipment and machinery (including stone processing and crushing equipment) and full-shift dose measurements to determine worker noise exposures. The findings identify the equipment and machinery that are likely to cause worker overexposures and identify the workers found to he experiencing overexposures. In addition, the benefit of cabs in reducing mobile equipment operator noise exposure is discussed.

This Bureau of Mines publication describes the plan used to instrument two longwall gateroads at the Powhatan No. 4 Mine of the Quarto Mining Co. Vibrating wire stressmeters, flat jack U-cells, multipoint extensometer stations, and convergence stations were installed in or on the coal pillars, roof bolts, and roof strata of the gateroad entries. The instruments measure pillar stresses, bolt loadings, and strata movements as the gateroad entries are developed and the longwall panel(s) is mined. The report details only the instrumentation plan of the longwall gateroads and not the evaluation of any subsequent data. This is because a complete analy-sis of the data cannot be made until extraction of the longwall panel(s) is complete.

Jan 1, 1982

By D. A. Stanley

The Bureau of Mines is investigating a method of dewatering flocculated fine-particle waste that involves treating the waste with a high molecular-weight polymer such as polyethylene oxide (PED) followed by dewatering on a static screen and/or in a trommel. Dilution of the polymer solution used for dewatering and use of the ion-exchanged form of the montmorillonite clay were found to be major factors determining the amount of polymer required to dewater clay-containing slurries. The amount of polymer, A, required to dewater ion-exchanged montmorillonite can be described by the equation, An = kC + b where n, k, and b are empirical constants and C is the concentration of the polymer solution used for dewatering. Clays that require large amounts of polymer for dewatering also dewater to a lower solids content. The concentration of the polymer solution is important because it affects the radius of the polymer coil in solution and hence its ease of transfer to a bridging configuration by shear. The constant, n, a function of the charge to hydrated radius of the exchange ion, relates to the strength of the bond between the polymer and the surface of the clay through a water bridge. The constant k is related to the hydrated radi-us for sodium or to the unhydrated radius for the other exchange ions.

Jan 1, 1986

By W. T. Millar

Magnetite mines in the Sterling tract, Orange County, N. Y., were operated almost continuously from pre-Revolutionary days until 1923. The Red-Back mine, one of several in this tract, was discovered in 1780; operated briefly in 1880; and abandoned, presumably because the iron ore contained considerable sulfur. The mine is in rough, mountainous country, with altitudes ranging from 500 to 1,100 feet. The magnetite deposit occurs in complex metamorphosed pre-Cambrian formation and is thought to be a replacement of limestone by magnetite. A dip-needle survey, completed in 1916, traced magnetic anomalies for a mile along the outcrop. A preliminary examination of the Red-Back mine was made by W. T. Millar, Bureau of Mines engineer, in December 1942. The Bureau of Mines bored seven diamond-drill holes aggregating 2,727.6 feet during the winter of 1943-44. A zone of magnetite mineralization was intersected in each of the holes.

Jan 1, 1949

By W. J. Johnson

This report presents the Phase I progress in the development of a Radar Coal Thickness Sensor (RCTS) being conducted by Boeing Aerospace and Electronics for the Bureau of Mines. A method is developed for measuring both the dielectric constant and depth of the coal shale interface using a modified UHF network analyzer and antennas in proximity to the surface of the coal. Both bistatic and monostatic systems, are compared. The algorithm technique uses synthetic range gating for clutter rejection and full polarimetric scattering matrix techniques to extract the dielectric constant and depth to sub-wavelength accuracies. Tests were run both in the lab and in a coal mine to build an error budget and demonstrate a validation of the model. The development of a prototype radar suitable for coal mine robotics is specified.

Jan 1, 1990

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference Index with abstracts of all pertinent literature. A particular strawman system design analysis is Included for the Helvetia Coal Co. Lucerne #8 mine In the Upper Freeport seam.

Jan 1, 1979

By James P. Bennett

To improve construction materials for emerging chemical and metallurgical technologies, the Bureau of Mines is investigating the acid resistance of ceramic materials. In the study described here, eight commercial ceramic materials comprising two red shale, two fire clay, a silica, a silicon carbide, a carbon, and a high-alumina brick were evaluated. Samples were exposed to 20 wt-pct HC1 at 50° C for 110 days. The test apparatus designed to evaluate the materials is described. Changes in chemical and mineralogical composition, cold crushing strength, volume, and weight, and leach rates of AI, Ca, Fe, K, Mg, Na, Si, and Ti ions were monitored. In general, the statistically significant physical property changes that occurred were small. In many cases, no changes were detected.

Jan 1, 1982

By Terry S. Cory

This report describes a complete system design methodology for medium frequency (MF) wireless radio systems for use in coal mines. The emphasis Is on AC mines where no trolley wire exists and, for which, conventional trolley phone communications can not be used. The report constitutes an MF system design handbook and includes a compendium of all previous MF technology elements as well as a reference index with abstracts of all pertinent literature. A particular strawman system design analysis is included for the Helvetia Coal Co. Lucerne #8 mine in the Upper Freeport seam.

Jan 7, 1979

By L. C. Marchant

Results of detailed analyses of four cores from the Threemile Canyon area in the P. R. Spring tar sand deposit in Utah are reported by the Bureau of Mines. The cores were obtained by the Utah Geological and Mineralogical Sur-vey as part of a l7-corehole evaluation program in the P. R. Spring, Hill Creek, and Rim Rock tar sand deposits. Average properties of the oil zone in the Threemile Canyon area as deter-mined from these cores are as follows: Oil saturation, 67.4 pet of pore volume; porosity, 29.2 pct; permeability before oil extraction, 133 millidarcies; and permeability after oil extraction, 2,855 millidarcies. Average net thickness of the oil zone is 23.8 ft and average depth to the top of the oil zone is 189 ft.

Jan 1, 1974

By R. O. Kneisley

Rock mechanics measurements indicate that the present two-bed mine design used at the Big Island trona mine, Green River, Wyo., results in stable workings. Vertical pressure changes in the lower panel pillars and horizontal pressure changes in the lower bed roof and floor indicated negligible upper bed mining influence. Pillar stresses stabilized soon after upper bed mining was completed. Strata movements in the pillar ribs, roof, and floor were also negligible and stabilized soon after completion of upper bed mining. Using tributary area theory, the confined core approach, and studies of model trona pillars it is shown that increased extraction ratio is possible. A program of gradually increased extraction ratio accompanied by simple measurements should result in a mine design that includes both higher recovery and long-term stability.

Jan 1, 1981

By F. C. Trutt, J. Sottile, J. L. Kohler

Presented in this paper is a theoretical review of the relationships that should exist between electrical winding parameters and the mechanical vibration of a-c machine elements under normal and faulted operating conditions. Also included is data from an experimental study that relates stator vibration and bearing vibration to selected winding faults in a synchronous machine. Consideration of these results indicates a significant relationship between electrical deterioration and mechanical vibration and thus provides the motivation for additional study and a basis for future applications.

By Ronald D. Hill, Elmore C. Grim

Surface mining drastically alters the ecological characteristics of the area disturbed and in some cases has a decided effect on surrounding areas. Vegetation is removed, topographic features and characteristics are changed, and the original geologic overburden profiles are destroyed. Spoil banks generally are a heterogeneous mixture of rock fragments, rock particles, and soil-sized material derived from the overburden strata. With proper mining techniques, the various strata can be partially or completely segregated. Segregation of over- burden material offers the opportunity to bury the toxic, acid, or salt-pro producing strata under growth supporting material. In some situations, lower strata may have more desirable characteristics than surface material and can be placed near or on the surface. For example, limestone strata appear in some lower overburden profiles that have shale and/or sandstone near the surface. Also, some lower strata have higher nutrient levels that have been leached from the surface. Experience has shown that natural revegetation is a very slow process on strip mined areas. Native vegetation may not be compatible with the environment on the mined areas, for example : 1. Low nutrients in the spoil. 2. Toxic spoils (very acid or highly alkaline ). 3. Surrounding vegetation may be of the climax type and may not have pioneer- or primary-invader-type species present. 4. The seed source may be to far away from the adjacent mined areas. Early attempts to revegetate strip-mined lands with trees also proved to be unsatisfactory as they did not provide the initial ground cover required to stabilize the spoil. Erosion control with trees only may take up to 10 years before the canopies close and an effective cover is established. They are slow to form soil profiles and do not provide effective chemical pollution control until long after planting. A quick growing cover of herbaceous species is necessary to obtain quick stabilization and initial protection against erosion by reducing runoff and rain-drop splash. Vegetative cover will also build up a concentration of organic matter in the soil, which in turn will

Jan 1, 1974