Search Documents

By John A. Breslin

Three scale models of coal mine entries and mining machines were constructed by the Bureau of Mines to study the effects of ventilation parameters on dust concentrations where mining personnel would be working. A one-fifth-scale model of a coal mine entry with a drum-type continuous-mining machine and a one-sixth-scale model of an entry with a twin-borer-type machine were used as well as a one-fifth-scale model of a longwall face with a double-drum shearer. Methane was used as a tracer gas to simulate respirable dust in the models. The distance of the end of the brattice or tubing from the face was found to be more important than the airflow rate for the drum-type machine. Dust reductions greater than 90 pct were shown to be possible with a secondary ventilation system used with the twin borer and a dust collector mounted on the longwall shearer. Cutting-head speed had a significant effect on concentrations at typical positions of miners with the drum-type machine and longwall shearer but not for the twin borer.

Jan 1, 1976

By John R. M. Hill

The Bureau of Mines performed elastic-plastic, finite-element analyses to investigate the support performance of hydraulic backfill. A mathematical model was developed for two vertically adjacent stopes separated by a sill pillar. An exact duplicate of a working stope was not intended; however, the model did simulate a working stope to the extent that field measurements from an active stope could be used for comparative purposes. Using a predetermined mining sequence, the computer analysis simulated the mining operation as a series of incremental cut-and-fill steps. Computer results included a complete history of stope closure and pillar stresses throughout the mining sequence. With the mining sequence and rock properties held constant, three separate analyses were made using varying backfill properties. These cases included no fill,-low-to-medium-quality fill, and medium-to-high-quality fill. Results of these analyses show decreases in stope closure and pillar stresses as the backfill quality increases, thus reducing the possible occurrence of rock bursts. Predicted stresses within the backfill compare favorably with field measurements. A relationship between maximum stress normal to the stope wall and the ratio of relative fill stiffness to relative rock stiffness was also indicated.

Jan 1, 1974

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (T.G. Soda Ash, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gages to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gages were 12.5 mm long and embedded into a remanufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gage locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.

By B. W. Jong

The U.S. Bureau of Mines investigated anhydrous chlorination and caustic-acid leaching processes to recover Ni, Co, Mo, and W from waste hydroprocessing catalysts. In batch laboratory-scale equipment, the chlorination process extracted 61 to 99 pet of the metals. Final recovery was 65 to 99 pct. The caustic-acid leaching process extracted 81 to 98 pct of the metals. Final recovery was 36 to 99 pct. Chlorination processing included roasting, chlorination, hydrolysis of metal chlorides for recovering Mo or W, water leaching of Ni or Co from the spent charge, purification, and solvent extraction or precipitation of Ni or Co from the purified solutions. Caustic-acid leach processing included NaOH leaching, solvent extraction of Mo or W from the NaOH leach liquor, H2S04 leaching of the NaOH leach residue, purification, and solvent extraction or precipitation of Ni or Co from the purified solution. The estimated fixed capital cost for a commercial-scale plant processing 39,000 Ibid of waste Ni-Mo-AI catalyst was $8 million for the chlorination process and $9.6 million for the caustic-acid leaching process. The estimated operating cost was about $0.20 and $0.40 per pound of the waste catalyst, respectively, for the two processes.

Jan 1, 1989

Provide the National Park Service (NPS) with guidelines for closing abandoned mine openings such as shafts and adits. Approach The NPS needed alternative methods of closing a variety of abandoned mine openings on National Park lands. Because the U.S. Bureau of Mines (USBM) has a long history of mining-related experience, the NPS requested that the Bureau provide them with technical mine closure information. USBM engineers compiled information on various types of mine closures and prepared technical illustrations of those closure techniques. Multiple closure options, by type of opening, were prepared as one-page field guides to assist NPS field personnel in determining the most appropriate closure method for a given situation and detailing the construction of the closure method. Results Guidelines provided to the NPS included a description of the method, use applications, construction techniques, technical illustrations, and technical support information. The following provides a brief description of 11 mine closure techniques identified for use by NPS personnel. Most of the closure methods, except the backfill methods, allow for construction that can provide access to the mine. However, providing access makes the closure susceptible to vandalism. Most closure methods require periodic monitoring for subsidence and corrosion or deterioration of construction materials.

Jan 1, 1994

By Paul B. Harder

Round Mountain Gold (RMG) in central Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By Paul B. Harder

Round Mountain Gold (RMG) in cen­tral Nevada, reports that over a nine-year period and a million operating hours, its fleet of 150-ton and 190-ton haul trucks has averaged better than 93% availability, with some of the trucks approaching 70,000 operating hours. Repair costs have been far below industry averages. Mine operations manager Pete Kesl credits the high availability and low repair costs to a succession of Product Support Agreements between RMG and Caterpillar dealer Cashman Equipment. He adds that good equipment and a high level of trust and co­operation between all parties to these agreements have been essential to their success at Round Mountain.

Jan 1, 1998

By C. A. Komar

Hardness, tensile strength, and impact toughness of dry and brine-saturated sandstone specimens were measured at ambient, cryogenic, and elevated temperatures as a measure of the relative stability of reservoir rocks for subsurface disposal of liquid wastes. Hardness measurements were inconclusive. Tensile strength and impact toughness were significantly higher at -320° F than at ambient temperature, but were relatively unaffected at 700° F. Impact toughness was reduced by subjecting the specimens to three cycles of rapid temperature changes (thermal shock) over a 1,000° F range. Tensile strength of brine-saturated sandstone was less than that of dry sandstone. Based on results of the tests, reservoir sandstone likely would be stable if exposed to extreme temperatures of liquid wastes, although rapid changes in waste temperatures should be avoided.

Jan 1, 1971

By H. William Zeller

The Bureau of Mines performed laboratory research to determine the effects of a barium-based fuel additive on diesel particulate emissions. The test engine was typical of types used to power underground coal min-ing equipment. Test parameters consisted of baseline measurements without additive, three fuel additive concentrations, and five steady-state engine loads, all at 1,200 r/min. Additive effects on soot mass concen-tration, opacity, particle size distribution, volatile fraction, and NOx emissions were determined. Important findings are as follows: Using the manufacturer's recom-mended additive concentration increased the gravimetrically measured mass of particulate by 30 to 80 pct at four of the five steady-state load conditions. Soot measurements by optical methods did not agree with those by gravimetric techniques, for additive-treated fuels. The additive reduced volatile hydrocarbons adsorbed on filter deposits by up to 50 pet. At most engine loads, carbon particulate was also reduced. About 40 pet of the barium added to the fuel was accounted for in the exhaust. The health implications for miners were considered, but no firm conclusions were drawn or recommendations made because the results are for steady-state conditions, which may not be representative of real-world operation of diesel-powered equipment underground.

Jan 1, 1987

By W. E. Lamont

The Federal Bureau of Mines conducted research to develop methods of removing phosphorus from the earthy, calcareous hematite ores of the Birmingham, Ala., iron district while simultaneously improving the grade and recovery of the iron values prior to furnacing. An attempt was also made to identify the phosphorus minerals present in the ores. The ores contained about 36 percent iron, 12 to 16 percent CaO, 15 to 20 percent hydrochloric acid insolubles, and 0.30 to 0.36 percent phosphorus. Fractions containing 5 to 15 percent phosphorus were isolated from the ores. Collophanite, Ca3P2O3?nH2O, a member of the apatite group, was the only phosphate mineral identified. Beneficiation methods using flotation and reduction roasting with magnetic separation yielded good grade iron concentrates, but were not as effective for reducing the phosphorus content of concentrates. Reduction roasting followed by fine grinding, magnetic separation, and acid leaching gave iron concentrates containing 62.5 percent iron and 0.04 percent phosphorus with an iron recovery of 82.9 percent and a phosphorus rejection of 93.7 percent. Reoxidation of reduced magnetic concentrates followed by acid treatment gave iron concentrates containing 58.1 percent iron and 0.02 percent phosphorus with 89.6 percent recovery of the iron and 96.5 percent rejection of the phosphorus.

Jan 1, 1973

Determine the extent to which remote-sensing techniques, primarily lineament analysis, can be used to identify geologic structures that may affect the location and migration of subsidence over abandoned underground coal mines in the Colorado Springs, CO, area. Compile data using a geographic information system (GIS) to allow efficient and reproducible comparisons and analyses. Background The basis for evaluating abandoned mine land (AML) sites with remote-sensing techniques comes from past and ongoing Bureau ground control research using remote-sensing data to identify potential hazards caused by geologic structures (faults, joints, etc.) above active underground coal mines. Research showed that lineament (linear feature) analysis of Landsat Multispectral Scanner (MSS) images could indicate locations of fractures and fracture trends that had varying, but significant, impacts on the stability of mine openings. Such geologic structures should be identifiable over abandoned mines as well. If fractures are present, even if they arc not faults, they should represent areas of potential instability over these mines and, therefore, should tend to localize subsidence when it occurs, particularly for deep and moderately deep portions of mines.

Jan 1, 1992

From the National institute for Occupational Safety and Health Disasters take many forms and demand quick response from emergency workers. They may include natural disasters such as earthquakes or hurricanes, or they may involve manmade disasters such as technological failures or terrorist attacks. As a member of an emergency response team, you and your team members are at risk of experiencing what psychologists refer to as a traumatic incident—an incident that may Involve exposure to catastrophic events, severely injured children or adults, dead bodies or body parts, or the loss of colleagues, for instance. Traumatic incidents can produce unusually strong emotional reactions that may interfere with your ability to function at the scene or later: You may experience any of the physical, cognitive, emotional, or behavioral symptoms listed below in Table 1. Some people experience emotional aftershocks weeks or months after they have passed through a traumatic event. Others may experience these reactions while still at the scene, where they must stay clearly focused on constantly changing hazards to maintain their own safety and to rescue injured victims.

By R. P. Adams

Because of the extreme interest in materials with high melting temperatures and the advantages offered over the powder route for making high-density material, arc-melting and centrifugal-casting methods were investigated for preparing shapes of hafnium carbide with and without excess carbon. Highly satisfactory equipment was constructed and efficient operating procedures were established. Also, methods for preparing consumable electrodes and shrink-tolerant graphite molds were developed. Although crack-free hafnium carbide (6.3 weight-percent carbon) shapes were not made, coherent castings containing 9 to 13.5 weight-percent carbon were produced; the same compositions were shown to be resistant to thermal shock. Selected physical and chemical tests were performed on castings chosen for investigation by chemical and nondestructive inspection techniques. Electrical conductivity and thermal expansion measurements were made. Measurable oxidation of all the compositions studied was observed to start between 500° and 600° C. Attack by nitrogen, however, did not occur until temperatures exceeded 2,000° C. A linear relationship of the logarithm of the diamond pyramid hardness to the temperature was noted. Considerable scatter of the bend-rupture strengths at room temperature and of the tensile strengths up to 2,000° C was found. However, at the latter temperature and above, a definite relationship of strength to temperature was observed and some ductility was noted.

Jan 1, 1968

By C. B. Manula, R. L. Sanford, R. A. Rivell

Part I. DATA INPUT ALTERNATIVE 1

Jan 1, 1974

By J. N. Tomlinson

Trailing-cable splices are evaluated for moisture exclusion abilities after repeated travel over shuttle-car sheave wheels. Tests are conducted on cables with jackets made of neoprene, cholrosulphonated polyethylene (CSPE), and nitrile butadiene-polyvinyl chloride (NBR-PVC) to 50° C. The results show that some splice kits are effective as received, others are improved with minor but significant changes, and still others must be redesigned to be effective in underground applications. Laboratory results are compared with actual underground splice results. Recommendations for cable preparation prior to splicing are presented.

Jan 1, 1979

By A. Mayton, A. Brien, W. Porter, O&apos

In 2004, management at Unimin's Gleason, TN operation began implementing ergonomic interventions specifically targeted to reduce risk of musculoskeletal injuries (MSIs). Together with corporate and site management, Unimin identified work site hazards and began to modify work practices/equipment. Some interventions were relatively simple and were implemented immediately. Others, like improvements to a mobile shredder, were more complex but were eventually resolved through a participatory approach with employees, management, manufacturers and NIOSH. This paper discusses ergonomic interventions that were successfully implemented using a bottom-up approach to reducing the risk of injury.

By D. A. Wilson

A process was developed on a laboratory scale in which a solid waste byproduct from refining of secondary lead was converted into three valuable products. Roasted lead blast furnace matte was leached with water to recover copper. This was followed by brine leaching to recover lead. Residues were finally smelted to yield pig iron. Copper was precipitated as cement copper and the lead product obtained was a mixture of pure 3PbO.PbC12.xH20 and Pb(OH)C1. Copper recovery was 89 percent and lead recovery was 96 percent.

Jan 1, 1967

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX E EQUIPMENT USED FOR FIELD TESTING OF MINE SEALING SYSTEM I. Drilling Operation - Equipment supplied by local drilling contractor 1. Mobile drill rig. 2. Flat bed truck, containing 20 lengths of drill pipe. 3. Auxiliary compressor. 4. Pickup truck for small parts and supply of diesel fuel. 5. Bulldozer. 6. Water supply, in this case the nearby stream. 7. Supply of casing, positioned next to the drill rig. 8. Ready mixed cement grout. 9. Drill bits, stabilizer units, cutting and welding equipment, other miscellaneous tools and supplies. II. Sonar Probing Operation 1. 25 foot tower with pulley mounted atop. - FMA 2. Electric winch with 100 feet of 1/4-inch cable, Model No. 100A, City Engineering Co. , Indianapolis, Indiana. 3. 400 feet of 1-1/2-inch-diameter aluminum pipe with alignment holes and coupling grooves. - FMA*

Jan 1, 1973

By S. D. Sanders

Goals of the Bureau of Mines include utilizing readily available minerals as substitutes for scarce mineral commodities and minimizing occupational hazards associated with mineral processing occupations. Therefore, the Tuscaloosa Research Center investigated using rapid-set cement as a suitable molding sand binder for small ferrous castings; currently petroleum-based binders are used. Substitution of a rapid-set cement would eliminate organic vapors associated with the petroleum-based binders; these vapors constitute occupational hazards and environmental pollutants. A binder containing 60 percent white portland cement (WPC) and 40 percent calcium aluminate (CA) would be an acceptable and economic substitute for petroleum-based binders where the foundry requirements are compatible with its limitations. It produced a set time and a pattern strip time of less than 1 hour. Cement, sand, and water mixtures developed compressive strengths from about 40 to 75 psi after 2 hours and from 120 to 130 psi after 24 hours. Tensile strengths of 18 to 22 psi were obtained after 2 hours, increasing to 30 to 35 psi after 24 hours. The addition of about 1 percent polyphosphate to the sand-cement-water mixture doubled the compressive strength and increased the tensile strength about 50 percent after 4 hours, but also increased the set time from 30 minutes to 1 to 1-1/2 hours. Po1yvinylacetate (PVA) resin latex additions resulted in rapid strength development. When castings were poured into the cement-bonded molds, the surface finish was fair to good on gray iron castings, but some areas of burn-on were present on steel castings. Using a graphite wash on the cement-bonded molds produced good surfaces on gray iron castings.

Jan 1, 1979