Search Documents

By L. H. Harrison

In coal mines equipped with electrically driven mechanical mining equipment, the problem of protection for electrical circuits and machinery important, because the hazards of fires and explosions resulting from electrical failures is greater than in most other industries. There is need for better methods and improved protective devices for this service. Studies and tests designed to determine possible value of the short-circuiting contactor as an electrical device for coal mine service were investigated. Preliminary made to determine the operating characteristics of the device, after which tests were made under actual service in three coal mines. Ordinarily, electrical protection in coal mines is divided into three classes, as follows: 1. Overload protection that is intended to protect against damage from overheating and excessive mechanical strain due to overloading. 2. Short-circuit protection that provides a means of de-energizing the equipment instantly when an accidental short circuit occurs in the equipment or on the power system. Short cm protection tends to damage from fires and, explosions resulting in the dissipation of large amounts of electrical energy in a short circuit. 3. Ground fault protection that, in its various forms, is intended, to maintain the frames of electrical equipment at or near the same potential surfaces in contact with the earth for the purpose of safe-guarding human life.

Jan 1, 1951

By George Markon

The rapid growth and development of the Soviet coal industry rank the U. S. S. R. with the United States among the leading coal-producing countries. The coal resources of the Soviet Union are among the largest in the world, although coal development has been hindered by the disadvantageous location of the coal deposits with respect to the major consuming centers. Although coal production in the U. S. S. R. reached a record high, the total energy output of mineral fuels in 1957 was still far below that of the United States because a significant part of Soviet coal output was lignites or lower rank coals. Although the Soviet coal industry soon may exceed that of the United States in tons produced, the energy equivalent of Soviet output will be considerably less because of the inclusion of a high percentage of lower rank coals. Energy sources in the United States also involve large quantities of oil and natural gas, whereas coal supplies most primary energy in the Soviet Union.

Jan 1, 1959

By Robert W. Metcalf

The feldspars are a series of related aluminum silicates containing varying proportions of potash, soda, rind lime; smaller amounts of other minerals arc likely to be present as impurities. They comprise three principal types: Potash spars, microline and orthoclase (KA12Si208); soda feldspar or albite (NaA1Si308); and soda-lime e (plagioclase) fellspars. The last-named is an intermediate group ranging from albite through oligoclase, andesine, labradorite, and bytownite to anorthite or line feldspar (CnA12Si2O8), Minor varieties are barium feldspar or celsian and a potash-barium feldspar. Perthite is a mixture of orthoclase end albite in alternate layers. Graphic granite or "corduroy spar" is an intergrowth of feldspar and quartz characteristically in the ratio of 3:1. Cornwall stone is a natural mixture of feldspar, quartz, end kaolinite imported in former years in sizable quantity from Cornwall, England. (A similar synthetic mixture, including some fluorspar, has been blended and marketed in the United States as "Carolina stone".)

Jan 1, 1941

By J. M. Mutamansky

"Coal mine dust research throughout the world has been stimulated by the recognition of its importance in the development of coal miners' diseases, particularly coal workers' pneumoconiosis (CWP). A historical look at the problem and the present state of knowledge in this area of importance to the worldwide coal industry is presented. A summary of progress made in this area is provided and some research ideas for the future are discussed.1. INTRODUCTIONI thank Dr. Yong Won John, President of the Korean Institute of Mineral and Mining Engineers, for his invitation to address the International Symposium on Coal Mining and Safety. This presents me with an interesting opportunity to take a broad look at the research in coal mine dust and where we are going. From this broad perspective, we can all view the progress and problems that are apparent in the present state of knowledge of coal mine dust. One important element in the review of coal mine dust research and its role in miners' diseases is that of its history. The existence of diseases attributed to the mine atmosphere is often traced back to Pliny the younger in the first century A.D. His work on natural history mentioned observed human effects attributed to mine fumes and vapors. However, the subject of the effects of dust in the mine was not mentioned in published literature until 1556 when Agricola discussed the ailments of miners in his day (Seaton 1975).For many centuries, many medical ailments of the lungs were often categorized together and distinct diseases were often not recognized until more modern times. The ability to distinguish different lung diseases was limited until the discovery of X-rays in 1986. Nonetheless, Zenker in 1866 applied the term pneumonokoniosis to any disease where dust gathers in the lymphatic depots of the lungs. This term was changed to pneumoconiosis in 1932. While pneumoconiosis was defined in the 1800s, scant attention was paid to control of miners' diseases until recent decades. The first attempt to control disease through control of the mine atmosphere has been attributed to the South Africans who instituted a silica control in 1910 (Drinker and Hatch 1954)."

Jan 1, 1989

By David L. Bickel

Stress-relief techniques and instrumentation have been developed through many years of research in the Bureau of Mines and successfully used to determine the in situ state of stress in rock. This report describes the Bureau's three-component borehole deformation gauge and the drilling equipment and accessories used with it. Operation and calibration procedures for the deformation gauge are discussed in detail, along with site selection and overcoring procedures. Information and references included in this publication provide a guide to the Bureau's cover-coring method for determining rock stress.

Jan 1, 1985

By H. B. Brunot, L. C. IlsLey, E. J. Gleim

"INTRODUCTION To supply inspectors, safety engineers, and others with detailed information as to the safety features of the various electrically operated machines that have been approved as permissible by the Bureau of Mines, three bulletins and five reports of investigations have been published dealing with the various classes of approved machines:Bull. 313, Permissible Storage-Battery Locomotives and Power Trucks.Bull, 343, Permissible Coal-Handling Equipment Approved from January 1926 to December 1930, inclusive.Bull. 382, Permissible Coal-Cutting Equipment Approved Prior to July 1, 1932.Rep. of Investigations 3309, Permissible Electrically Operated. Air Compressors.Rep. of Investigations 3326, Permissible Electrically Operated Room Hoists.Rep. of Investigations 3345, Permissible Electrically Operated Rock-Dust Distributors.Rep. of Investigations 3363, Permissible Electrically Operated Hand-Held Coal Drills.Rep. of Investigations 3391, Permissible Electrically Operated Post Drills and Drilling Machines.The present paper gives similar information relative to the mine pumps approved before October 1, 1939."

Mar 1, 1940

By T. F. Myners

This paper, describing the concentration methods and costs of Witherbee, Sherman and Company at Mineville, N. Y., is one of the series of papers on milling methods and costs being prepared by the United States Bureau of Mines. It deals principally with the production of high-grade concentrate. ACKNOWLEDGMENT The author is indebted to C. F. Jackson, principal mining engineer, United States Bureau of Mines, to A. M. Cummings, general superintendent of Witherbee, Sherman and Company, and to the company's engineering staff, for assistance in preparing this paper.

Jan 1, 1932

By Wilbur A. Haley

The demand on the nation's reserves of high-quality coals suitable for metallurgical purposes is resulting in the rapid depletion of some of the thicker coal beds. These beds are thick enough to permit the use of modern mechanized mining equipment. Many of the thin beds are not being mined at present. In limited areas where the coal is less than 36 inches thick some beds are mined by various conveyor methods. Usually, the room-and-pillar system or some modification of it is used, and often no attempt is made to extract pillars. Consequently, an appreciable quantity of a valuable resource is lost. Many steel companies and coal operators consider reserves of low-and medium-volatile coking coals to be critical, especially in areas where the thin beds are not being mined by modern mining methods. To improve recovery and to promote more-extensive mining in thin beds, methods and devices that are new to American coal mining but applicable to the mining of thin coal beds should be tried. As one of the functions of the Bituminous Coal Mining Section of the Bureau of Mines is to promote improved mining practices and efficiency in the interest of conservation, research in that line is necessary. In 1945 coal planers were observed in operation in Germany by a Bureau engineer member of Solid Fuels Mission to Germany. Planer designs and history of early developments and operations were published. In 1949 an improved planer was again studied by Bureau engineers, and its adaptability to certain conditions in the United States, especially thin beds of friable coal, was considered practicable. After the war the planer was improved, in design and for several years has been operating successfully in the Ruhr. Because of the conviction that the device would be successful, both from the standpoint of conservation and operational prodl1ctivity, under certain conditions in the United States, the Bureau of Mines, through the Bituminous Coal Mining Section, entered into a cooperative agreement with the Coal Division of Eastern Gas & Fuel Associates and Mining Progress, Inc. The purpose of the agreement was to conduct an experiment in modified longwall mining, using a new-type German-built coal plow or planer, known as the Loebbe Habel, supplied by Mining Progress, Inc. The experiment was made to determine if this type of mining equipment operated on a longwall face could be adapted to some of the thinner American coal beds. Such an experiment also would afford many opportunities to study the possibilities and principles of this type of equipment as well as the many factors involved in the mechanical mining of a longwall face.

Jan 1, 1952

By Walter L. Fisher

The public interest in the Alaskan situation is such that, with the consent of the President, I have concluded, at the request of the American Mining Congress, to make at this time a candid, if somewhat informal, expression of the views I have formed as Secretary of the Interior, under whose official supervision much of the administration of the Territory is now placed. Pressure of other matters imperatively requiring attention has prevented their presentation in as precise and comprehensive a form as I had hoped. The absence of the President from Washington has also prevented the submission to him of what I have prepared. I wish to say, however, that no one is more earnest than he in the desire to see a policy of prompt and wise development inaugurated in Alaska, and that the general policy contained in this address has been discussed with him, meets his approval, and will have his support. I have recently returned from an altogether too brief but nevertheless a most interesting and profitable visit to those portions of Alaska that are more immediately involved in the questions now under public consideration. Favored by extraordinary weather and the cooperation of steamship and railroad lines and the assistance of all of the governmental agencies, including the Revenue-Cutter Service, I visited every port in Alaska that seems likely in the near future to become an important entrance to the country. I examined all of the harbor and town sites which for this purpose have attracted any considerable public attention. I traversed the entire length of each of the three railroads that have been constructed in the Terri.tory and made a short trip from White Horse down the upper Yukon. Both before and during the journey I examined a mass of books, records,' and papers relating to the country and its resources. I had conferences with official committees representing the principal communities I visited and with numerous individuals, residents both of the coast and of the interi.or, and conferred with engineers, miners, prospectors, railroad officials, business and professional men.

Jan 1, 1911

By J. L. Eakin, J. P. Powell

"The increased costs of exploration and drilling of new oil fields and the continued success of water flooding in nearly depleted oil fields have created a demand for information on the results obtained from individual projects. The Bureau of Mines has published several reports concerning water-flood activity in the Midcontinent area and at the request of the industry has continued to collect and disseminate this information. This report was written in response to these requests. It describes in detail the water-flooding projects in Anderson, Franklin, Linn, and Miami Counties, Kans., and includes methods of water treating and the results obtained. The production histories of each county and many water-flood projects are shown graphically from the date of the first development. Maps of most of the major projects, showing their status as of January 1, 1953 are presented also.The practice of injecting water to stimulate oil production was legalized in Kansas in 1935, and the first water-flooding project authorized in this four-county area was initiated by the Texas Co. in December 1935 in Linn County. Forty-nine projects2/ initiated in the area to January 1953 are estimated to have recovered approximately 10 million barrels of oil that would not have been produced by methods used previously. About 7,900 productive acres had been, or are, flooded by these projects, and approximately 136 million barrels of water had been injected.These four counties in the eastern Kansas shallow production area3/ were an important factor in the early history of the Kansas oil and gas industry. This position has been maintained from the very beginning through the early period of vacuum and air injection and into the era of water flooding. The location of the area and the relative position of the four counties and water-flooding areas in each are shown in figure 1.The first drilling for oil in this area in 1860 resulted from investigations of the existence, and use by the Indians, of so-called tar or oil springs. The first wells drilled were nonproductive, and the impending Civil War caused the search for oil to be discontinued. In 1884 a few shallow oil wells were drilled near Paola, and completion of several gas wells near that city led to subsequent drilling of an oil well, which was completed in June 1885, having an initial flow of 10 barrels of oil daily.In 1904 the original Paola gas field became a good oil-producing field. In 1905 the Rantoul field in Franklin and Miami Counties was opened; and drilling activity spread throughout the adjoining area, resulting in development of several shallow oil pools in Linn and Anderson Counties. The first ""shoestring"" pool in eastern Kansas to produce oil was probably the Paola or Pressonville shoestring, which was discovered in 1917. The rate of oil production from the area declined until 1919, when the Centerville shoestring pool was discovered. Discovery of the Colony gas field in 1921 was followed within a few months by drilling of the Garnett and Garnett and bush City shoestring pools. The Schermerhorn pool (now part of the Centerville field) s discovered in 1927, and the Kincaid shoestring pool was first drilled in 1931. The oil-production histories of the individual counties are discussed separately."

Jun 1, 1953

By Michael E. Henderson

The U.S. Bureau of Mines (BOM) constructed the Hydraulic Transport Research Facility (HTRF) to investigate the hydraulic parameters relating to the transport of coarse coal. To achieve these goals in a timely and efficient manner, the Bureau contracted to Boeing Services International (BSI) the responsibility of operating the HTRF and providing technical support. This data report is a summary of the testing and data results for the period 22 November to 10 December 1982. The testing covered herein is for coarse 2-in by 0 (minus 50 mm) Pittsburgh Seam coal in a 6-in (150 mm) pipeline, at velocities ranging from 5 to 20 ft/s (1.5 to 6.1 m/s) and at concentrations ranging from 15 to 45 pct by weight.

Jan 1, 1986

By Robert Louis Adams

A general discussion of the structure of the junk automobile recycling system shows that the generation of stripped automobile hulks and scrapped automobiles is price inelastic. As a result, it is extremely difficult for the price mechanism to automatically achieve an equilibrium that will prevent the accumulation of excessive automobile wrecker inventories and vehicle abandonment by the last owners of scrapped cars. The new shredder processing technology and the new portable flattener technology have altered the structure of the junk automobile recycling system. The shredder technology has increased the demand for processed automobile scrap. This increased demand is reflected in higher prices paid for hulks by scrap processors. The portable flattener has reduced the transportation cost of shipping hulks to processors. The two new technologies have eliminated, at least potentially, the net cost of shipping stripped hulks so frequently incurred by wreckers in the past. The elimination of this cost eliminates the economic incentive for excessive wrecker inventories. Unfortunately, the incentive for last owners to abandon their cars does not appear to have been eliminated by the new technologies. The last owner of an automobile with no spare parts value is still likely to incur a cost by delivering his automobile to the recycling system. Although a subsidy payment is probably unnecessary to reduce excessive wrecker inventories, such a payment might be one solution to the problem of automobile abandonment. However, there are a wide variety of subsidy programs that could be introduced. Before any Federal subsidy program is introduced to reduce automobile abandonment, it is recommended that the program be tested on a limited basis in many different parts of the country.

Jan 1, 1973

By G. E. Johnson

Batch tests of coals and coal-derived materials were made by the Bureau of Mines to determine their effectiveness in removing organic contaminants (COD or chemical oxygen demand, comprising those organic compounds that can be chemically oxidized, and ABS or alkylbenzene sulfonate, common household detergents) from the final effluent of secondary-treated waste waters. The adsorptive capacities of flyashes, coals, including at least one sample of each rank found in this country, pretreated coals, and miscellaneous materials including commercial chars and coke, were determined and compared with that of granular activated carbon. The coals, though not as effective as activated carbon, possess an economic advantage--they are relatively inexpensive, and they can still be burned as fuel without any loss of fuel value after use in waste¬water treatment. A hvcb coal was found to be one of the best, having about one-fourth the capacity of activated carbon for COD, adsorbing about 4 percent of its weight before it became saturated. Several coals contained constituents that added to the COD content of the treated water. Thus knowledge of the performance of the coal is necessary to insure selection of a proper coal as adsorbent.

Jan 1, 1966

By K. J. Liles

This Bureau of Mines paper describes the composition and properties of drilling fluids for use in high-temperature geothermal wells, and summarizes the problems encountered with fluid use at the known major geothermal sites throughout the world. These include the western continental United States, Hawaii, Italy, Iceland, Japan, New Zealand, and Turkey. Water-base drilling fluids of 9- to 10-lb/gal weights are relied on primarily for geothermal well use, although air drilling is sometimes used. Bentonite-lignite-water systems have been used most often, and additives such as polyacrylates, lignosulfonates, and chromates are employed to improve the properties of the basic system.

Jan 1, 1976

By W. P. Diamond, B. M. Bench, C. M. McCulloch

Coalbeds exhibit a directional permeability, with the maximum permeability oriented parallel to the face cleat. Thus, the most efficient pattern of vertical degasification holes for a coalbed is dependent upon cleat orientation. Surface joints, infrared photolinears, and Ronchi grating photolinears were investigated as potential estimators of subsurface cleat orientation. Cleat orientations were masured in 18 mines, in the Pittsburgh coalbed in southwestern Pennsylvania and northern West Virginia to be used as a standard against which prediction techniques would be evaluated. Two cleat systems with a strong geographic segregation were measured in the study area: N 67° W - N 28° E (95° separation) for the north, and N 76° W - N 17° E (93° separation) for the south. Directional data obtained from the three techniques investigated yielded satisfactory regional predictions of cleat orientation. Analysis of surface joints was the only technique considered sufficiently reliable on a local basis. Prediction of cleat orientation is based on the pairing of the principal directional sets into all reasonable combinations of fundamental systems. The system or systems composed of the most dominant sets nearest to 90° separation are likely to be a reliable prediction of cleat orientation. The most dominant set of the system selected is likely to be the face cleat.

Jan 1, 1976

By J. R. Thoenen

During the past 6 years the Mining Division of the U.S. Bureau of Mines has prepared many information circulars containing valuable technical data covering the operating details of mining and ore-dressing plants throughout the United States, Canada, Mexico, and other countries. These papers, written for the most part by operating officials in the field, have been designed to comprise a reference library for the operating engineer. In order to make the information contained in these publications more readily available to the busy engineer the enclosed series of reference tables has been compiled. The tabular arrangement is by subject rather than alphabetical order, thus avoiding the bulk of an alphabetical index.

Jan 1, 1935

By James C. Barker

The analytical variability encountered when sampling for platinum-group metals (PGM) was statistically evaluated during a 1983 study by the Bureau of Mines and the University of Alaska. Sampling procedures were designed to systematically incorporate commonly used reconnaissance exploration techniques under actual field conditions. Analytical variability was evaluated at each procedural step. Analytical data from each sample from a single deposit grouped relatively well around the calculated mean for that deposit. Standard deviations did not exceed 43 pct of the mean for any of the deposits; more commonly, the deviation was about 25 pct. Statistical treatment of the data by analysis of variance indicated the most important source of error is selection of the sample site. Two or more replicate samples appear necessary to adequately quantify the PGM content. Secondly, significant variation occurs during preparation of a pulverized split for fire assay. The optimum sample size was in the 11-lb range; larger samples did not appreciably reduce variability. Smaller samples generally indicated a higher degree of variability. Evaluation of the sample method suggested the common grab sample, if carefully taken, is a useful indicator of the general range of PGM concentration but potentially includes a considerable margin of error.

Jan 1, 1985

By Bernard Lewis

This report on the research and technical studies conducted by the Explosives Branch of the Bureau of Mines covers the 2-year period July 1, 1946, to June 30, 1948. A report for the fiscal year 1947 was omitted because of the large amount of work still in an unfinished state. The material presented herein is based largely upon more comprehensive reports prepared under the authorship of members of the branch staff.

Jan 1, 1949

By Thomas G. Chapman

The four major steps in the production of marketable copper are mining, concentrating, smelting, and refining. In a few cases, however, leaching takes the place of concentrating, smelting, and refining, and in others ores are smelted without being concentrated. Copper ores have been milled since the early days of mining in the United States. Except in the Michigan district, most copper ores went direct to the smelter until the so-called porphyry mines were developed. At present, although considerable leaching and direct-smelting ores are produced, the bulk of the copper ore mined is concentrated. Improved methods of concentration have kept pace with the increased tonnages of ores milled.

Jan 1, 1936

By Harold L. Riley

This Bureau of Mines paper describes the methods and practices used at the Peck quarry of the Crab Orchard Stone Co., Inc., one of the leading producers of dimension stone in the Crossville, Tenn., area. The product is marketed under the registered trademark "Crab Orchard Stone". Another large producer of stone from the Crossville district sells its product under the registered trademark of "Tenn-Quartz". Both companies, and a number of other companies and individuals who quarry and process dimension stone from the same general geological formation, are members of the Quartzite Producers Association of Tennessee. The salable product is shipped throughout the country for use as architectural building stone. In 1959, 653,008 cubic feet of stone was produced in the Crossville area and was sold for $1,414,405. Terms and descriptions used in this report are those of the quarry and building trades. The offices, pitching sheds, wire saws, railroad siding, and storage areas of the Crab Orchard Stone Co., Inc., are on a side road 0.3 mile north from a point 2.2 miles east of Crossville, Tenn., on U.S. Highway 70. The quarry is on this same side road 2.0 miles south of Highway 70. Crossville is 62 miles west of Knoxville and 65 miles northeast of Chattanooga, Tenn.

Jan 1, 1962