Search Documents

By F. R. Lee

THE Bureau of Mines was established in July 1910 to conduct research and to establish standards for mining equipment and practices which would conserve human life, natural resources, and property in the mineral industries. Several lists of equipment approved by the Bureau as permissible for use in gassy coal mines have been issued since then. The lists covering all approved equipment except breathing apparatus and explosives have born consolidated into two publications: Bulletin 343. Permissible Equipment Approved to January 1, 1953, and Information Circular 8220, Permissible Mina Equipment Approved By The Bureau of Mines During 1953-62. The, purpose of this publication is to supplement Bulletin 343 and Information Circular 8220 with a listing of permissible equipment approved during 1963 and 1964. The schedule, (standards) under which equipment listed herein have been approved are, as follows (cities and dates of approval and revision are, given in footnotes) : Schedule 2F,3 schedule 6D,4 schedule 7C,5 schedule 8C,6 schedule 9B,7 schedule 10C,8 schedule 12D,9 schedule 22,10 schedule 24,11 schedule 25B,12 schedule 25B,13 schedule 29A,14 schedule 30,15 and schedule 31.16

Jan 1, 1966

By D. F. Walsh

A study of damping capacity was made on a number of magnesium-base alloys, commercial types and experimental compositions. Hardness and tensile properties were determined, and the microstructure of each alloy was examined. Alloys of low yield strength, in general, possessed high damping ability. A correlation was established between damping capacity and composition.

Jan 1, 1962

By David J. Kusler

This report describes a primary or direct, continuously sampling, and automatically averaging gravimetric method for analyzing gaseous mixtures of carbon dioxide, carbon monoxide) hydrogen, and (by volume measurement) nitrogen. The gaseous mixture is analyzed by passing it at a controlled and definite rate through a system that permits carbon dioxide and water retained by appropriate absorbents to be determined and the residual-gas volume (essentially nitrogen) to be measured. The accuracy and dependability have been established by comparison with very carefully conducted Orsat analyses. The method was developed for, and has been satisfactorily applied to, the analysis of blast-furnace top gas. It permits relatively attention free operation, using simple and low-cost materials usually found as basic equipment in the analytical laboratory. It provides, over a wide range of time or sampling intervals (from less than 1 to over 24 hours), the average composition, in terms of volume-percent, for those components usually determined in blast-furnace gas, if (as is usual) the flow rate of gas from the blast furnace is essentially constant over a selected analysis interval. Oxygen and methane are not determined; but, since these gases are normally absent or present only in traces, their analysis is seldom required.

Jan 1, 1959

By J. W. Town

This report summarizes the results of laboratory investigations conducted by the Federal Bureau of Mines to obtain hydrometallurgical information on the dissolution of mercury sulfides from ores, flotation concentrates, and pure mercuric sulfides. Statistical methods were used to design the experiments and evaluate the resulting data. Studies demonstrated that cinnabar is readily soluble in sodium sulfide, partly soluble in potassium sulfide, and essentially insoluble in ammonium sulfide. Additions of sodium hydroxide or potassium hydroxide to sodium sulfide solutions increased mercury extraction slightly; when either was added to potassium sulfide or ammonium sulfide solutions, mercury extraction was equal to that of sodium sulfide. Tests at the Albany Metallurgy Research Center showed that sodium sulfide would completely dissolve chemically pure mercuric sulfide, more than 95 percent of the cinnabar in 5-percent mercury flotation concentrates, and 60 to 90 percent of the cinnabar in low-grade ores. The double-leach tests showed that potassium sulfide would dissolve over 90 percent of the arsenic in mercury-arsenic products and 1 to 10 percent of the mercury; then sodium sulfide-hydroxide solutions would dissolve 80 to 90 percent of the remaining mercury and 5 to 10 percent of the arsenic.

Jan 1, 1961

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982

As part of a continuing program of evaluating the Nation's crude-oil resource, this report presents information pertaining to resource, primary reserve, and potential waterflood reserve for 3,209 selected reservoirs contained in 24 oil-producing States, as of January 1, 1968. To that date the selected reservoirs had not been subjected to pressure-maintenance or secondary-recovery operations. These reservoirs also met the following parameters: (1) a minimum of five oil-producing wells on January 1, 1968, (2) a minimum of 50 acres areal extent, (3) a minimum of 50,000 bbl of oil ultimate primary recovery, and (4) the principal reservoir energy was other than active water encroachment. The selected 3,209 reservoirs produced 527 million bbl of oil in 1967, about 17 pct of U.S, total production. Primary oil reserve was 4,983 million stb; in addition, there was 6,043 million stb of potential water- flood oil reserve. Oil resource in the selected reservoirs was 59,547 million stb. A brief history and outlook of waterflooding are presented for each State. Depth and producing rate statistics and geologic distributions of production, resource, reserve, and potential waterflood reserve for the selected reservoirs are presented by States in the appendix. Also included in the appendix are description, history, and technique modifications of waterflooding, and a preliminary cost estimate of a closed-system water-injection project.

Jan 1, 1970

By Arne Landsberg

The Bureau of Mines measured the vapor pressure of FeC12 , FeBr2, FeI2, Sb, Bi, Cd, Mg, Pb, FeC13 , and VCl2 using the Knudsen-and torsion-effusion methods, and on FeC13 -NaC1 mixtures, Au2Cl6, and MgNi2 using only the Knudsen method. Apparent vapor pressures calculated from the experimental data vary with orifice size and method of determination. Reaction with residual oxygen in the instruments was noted to have an effect on the iron halide data. Vapor pressure curves plotted as log P versus 1/T (where P is pressure and T is absolute temperature) for one substance using several orifice sizes tended to converge at a single point when extrapolated beyond the experimental region. All of the data, except those of VC12, agree with previously published results. The importance of comparing effusion measurements with those obtained by other methods and the variations encountered with various orifice sizes are discussed.

Jan 1, 1977

By Richard D. Mehring

A refined ad improved self-sealing brattice for use in coal mine rescue and recovery operations for directing the flow of air has been developed and tested by Goodyear Aerospace Corporation for the U.S. Bureau of Mines. The brattice is made from a lightweight, low cost material that meets MSHA flammability requirements. The units can be erected using pins, spade or lightweight extensible poles. Tests here conducted to determine leakage rate from minimal to a maximum of 1.5" H20. The ability to handle reverse flows was demonstrated and a non-flammable foam was used as an auxiliary sealing agent.

Jan 1, 1978

By Bernard J. Steblay

The U.S. Bureau of Mines has attempted to use ultrasonic signal travel-time measurements to measure loaded roof bolt strains. The strain measurements are then related to roof bolt loads through equations or empirical calibrations. Such techniques offer the potential of accurate, rapid bolt load measurement that does not disturb the anchotage. This report presents 6e research findings for a specific type of ultrasonic measurement instrument using a pulsed-phase-Iock-Ioop technique. This technique measures signal travel time indirectly by measuring frequency changes. A complete development of the applicable theory and detailed derivations of key equations is presented along with empirical laboratory and field results. The differences between anticipated and measured behaviors are analyzed and discussed. The report identifies problems encountered in applying pulsed-phase-Iock-Ioop technology to roof bolt load measurement and provides potential solutions to many of them. A key assumption of pulsed-phase-lock-loop theory is that driving and reflected signal frequencies will always be equal. Findings showed that not only were actual frequencies not equal but they were not stable or simply related. Reflection wave shape also was not stable. The ramification of these findings and ways to minimize their adverse effects are presented.

Jan 1, 1990

By Robert T. MacMillan

An essentially chemical technique has been developed on a small scale for the efficient utilization of certain domestic titaniferous iron ores. Three main steps are involved: (1) Sintering the ore at 1,050° C. with carbon and soda ash to reduce the iron to metal powder, retaining the titania in the slag, (2) separating the powdered iron from the slag, after wet grinding, by magnetic or gravity methods, and (3) sulfuric-acid decomposition of the titania fraction to produce pigment and certain byproducts. The technique was first applied to the tailings from the Bureau of Mines bauxite-concentrating plant at Bauxite, Ark. A good grade of powdered iron was produced from this material. Subsequently, the work was diverted to the study of the titaniferous magnetite from the MacIntyre Mine at Tahawus, N.Y., because of the potentially higher recoveries of iron, titanium and vanadium. Ninety percent of the iron in this ore has been recovered as an iron powder analyzing 90 percent metallic iron and containing 2 to 3 percent TiO2. The remaining titania was found in the slag and was recovered as pigment-grade TiO2 by application of a suitable technique. The vanadium was distributed between the TiO2 fraction and the alkaline liquor resulting from the wet-grinding and magnetic-separation operations, with only a minor proportion retained by the metallic iron.

Jan 1, 1950

By L. B. Berger

Studies showing the effect of mixing hot exhaust gases with tie intake air of a four-stroke-cycle Diesel engine are described. The results indicate a marked increase in carbon monoxide in tip exhaust gases, a decrease in oxides of nitrogen, and no significant effect on aldehydes. The increase in carbon monoxide was greater at higher fuel-air ratios and was caused partly by the increase in fuel-air ratio end partly by the decrease in oxygen concentration resulting when exhaust has was added. The application of these results to the use of Diesel engines underground is considered.

Jan 1, 1940

By Wilbert J. Huff

[This is the fifth of a series of annual reports of the explosives Division, Bureau of Mines, United States Department of the Interior.3/ It deals particularly with work done during the period July 1, 1939, to June 30, 1939. The writer and the respective unit leader to whom credit is indicated have directed the various studies outlined.]

Jan 1, 1940

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and Other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By A. T. Harris

Ground quartzite, known in the industry as amorphous silica, is produced from a quartzite deposit near Honey Brook, Pa., by George F. Pettinos, Inc., of Bala-Cynwyd, Pa. The quartzite is mined by the open pit method and processed in a mill at the mine. The operation regularly produces five standard grades of sand and one grade of crushed stone; however, the company accepts special orders and will produce material to meet the customer's specifications. Beneficiation (chiefly crushing and screening) is controlled by laboratory screen tests on samples taken during preparation of the sand. The chief uses of the sand are for foundry operations, furnace lining, concrete aggregate, and other specialized uses. The quartzite in this deposit is of uniform composition and does not require control by chemical analysis. However, for special purposes, analysis will be furnished.

Jan 1, 1965

By Richard F. Link

The objective of this report is to explain a statistical method for the summarization, organization, and classification of multivariate assay and other data from the mineral industry. Multivariate data are those characterized by several measurements at each data point, such as assay data from a mixed metal mine, or blast furnace data. A specific method of linear discriminant analysis, the Mahalanobis d2 procedure, is explained, starting from elementary principles; the d2 procedure enables many measurements at many data points to be studied by investigating the interrelationships among the data. The relation of linear discriminant analysis to other statistical methods for treating multivariate data, in particular the eigenvalue technique of factor analysis, is also explained. Example analyses are made on data from the Frisco mine, San Francisco del Oro, Chihuahua, Mexico. The data comprise assay values for silver, lead, copper, and zinc taken at some 19,000 sample points distributed into 91 groups.

Jan 1, 1967

[Module 10. Internally Cued Operating Contingencies Prerequisite: Modules 1-7 - Estimated Instructional Time: 2.42 hrs. Module Abstract Trainees, using programmed instruction, describe the cues, consequences, operational sequences, and possible causes resulting from loss of air pressure from power fluctuations, and from a failure of the automatic lubrication system. Although some of the contingencies may be initially signaled by an alarm or from the oiler, each trainee will demonstrate proficiency in the appropriate operating techniques and procedures. This module also includes a review component for those trainees identified in the assessment exam as requiring less detailed instruction.]

Jan 1, 1976

By F. W. Lee

The paramount importance of water to life of all forms on the earth is too well known to require elaboration in this brief paper. It has repeatedly been termed the most valuable of all our mineral resources. Its importance is justifiably recognized in the extensive areas covering the earth which receive sufficient rainfall to sustain a relatively luxuriant vegetation; but in those areas where rainfall is insufficient to support anything but a relatively meager plant growth, the location of a water supply and its development become of even more vital interest to those attempting to obtain a living from the soil. Geological investigations concerning the water supply of the United States have been most extensive, important work having been accomplished by Federal, State, and local governments and by private enterprise. A casual examination of the titles of the 739 Water-Supply Papers published by the United States Geological Survey3/ alone testifies 'to the vital nature of our water resources and the extensive work that has been done on them.

Jan 1, 1936

By David K. Hylbert

This study was designed to investigate roof falls in room-and-pillar drift coal mines and to determine geologic methods for predicting unstable roof conditions. The study area was located in Harlan County, Kentucky and the Bailey Creek (Harlan coal bed) and Highsplint (Darby coal bed) mines were selected for study. Correlations were made laterally between surface outcrops and within the mines using lithologic and trend analysis criteria. Lithologic criteria compared cyclic changes in roof strata. Results indicated that roof falls are associated with zones of weakness within or between five vertical cycles recognized. Abrupt lateral facies changes occur. In the Highsplint mine the roof was classified in four categories or conditions using 98 rib sections for control. Structure contour and isopach maps were used to project axial trends of the sandstone roof. A roof-fall zone was examined using ten NX cores taken from the roof and included lithologic, petrographic and clay mineral studies. At the Bailey Creek mine roof failure was caused by the heading direction being driven subparallel to paleochannel directions. Computer programs were used in trend analysis studies. Cross-bedding, paleo-channel trough axis and sole mark studies indicated a 350 discrepancy between surface and in-mine trough axes at Highsplint. A direct relationship between joint and "slip" frequency and direction with sandstone roll trends was found. Surface joints compared well with drainage Segments, hilt did not correlate with roof falls in areas of mines under overburden in excess of 600 feet.

Jan 1, 1977

By Ott F. Heizer

This paper describing the practice at the tungsten concentrator of the Nevada-Massachusetts Co., Inc., at Mill City, Nev., is one of a series being prepared by the Bureau of Mines on milling practices, methods, and costs in the United States. The ore, which contains about 1.10 per cent of scheelite (CaW04), is concentrated on tables and by means of a magnetic separator and roasters. A product containing 70.43 tungsten trioxide is shipped. The plant was designed for a capacity of 100 tons per 24 hours, but at present 142 tons of ore are milled per day. The author acknowledges the assistance of William O. Vanderburg, associate mining engineer, U. S. Bureau of Mines, in preparing this paper.

Jan 1, 1930

By P. R. Jones

A computer program was written for the design of a shell and tube heat exchanger on a price optimum basis for the following conditions: (1) Triangular pitch; (2) single or multiple pass; (3) heating or cooling; (4) no change in phase; and (5) inside pumping costs immaterial. Price optimum design was obtained for four standard tube sizes and standard pitch. The inside pressure drop was fixed and outside pressure drop was computed for the optimum baffle spacing and when the baffle spacing equaled the shell diameter. Standard shells whose areas equaled or exceeded the required area were also listed. The program was made adaptable to various fluids and to various tube sizes and pitch by reading in many of the required data such as physical properties of the fluids, tube data, and standard shell data in tabular form.

Jan 1, 1968