Search Documents

By R. August Heindl

A process for recovering manganese from open-hearth steel-plant slags was investigated. The proposed method of accomplishing this is indicated by the flow diagram in figure 1. Mixtures of open-hearth, steel-plant flush slags and limestone, so proportioned as to have molar [CaO -3P205] ratios of approximately 2, were fired at approximately 2,400° F. in an oxidizing atmosphere and then cooled slowly. This treatment produced a clinker consisting principally of two solid phases comprised of (1) various combinations of the oxides of manganese, iron, aluminum, and magnesium, probably in spinel complexes, and (2) a dicalcium silicate phase, which contains the phosphorus. Reduction of these clinkers with hydrogen or with gaseous mixtures containing CO, CH4, and other hydrocarbons at about 1,300° F. formed manganous oxide as well as varying amounts of ferrous oxide and iron. Carbon monoxide and mixtures of hydrogen and carbon monoxide effectively reduced the clinkers but also gave higher proportions of soluble iron when the manganese was extracted from the reduced clinkers by leaching at about 80° F. with ammonium carbonate solutions containing 26 to 28 percent ammonia and 15 to 26 percent carbon dioxide. It is believed that the manganese is in solution as an ammonia-manganese complex. Concentrations of about 90 grams of manganese per liter were obtained by batch countercurrent procedures. By distilling 50 percent of the ammonia, the ammonia-manganese complex was decomposed, and approximately 90 percent of the manganese was precipitated as the carbonate with the simultaneous precipitation of 15 to 30 percent of the iron, the larger amounts of iron precipitating in the continuous tests. The manganese-iron ratio in the product could be increased either by recycling more manganese from the distillation to the extraction or by aerating the liquor to purge it of iron before, rather than after, the distillation step. Calcination of the pelletized manganese carbonate in an oxidizing stmosphere at 2,000° F. or above gave a final product, Mn304, resistant to crushing and apparently possessing the other physical properties essential in a ferromanganese blast-furnace feed.

Jan 1, 1955

By P. L. Woolf, N. Bernstein, M. M. Fine

Continuous experimentation utilizing a 3- by 36 - foot rotary kiln was conducted to demonstrate the feasibility of simultaneous induration and reduction of magnetic taconite concentrate . Lignite , or lignite - anthracite mixtures , and green magnetite pellets (64.2 percent Fe , dry basis ) were heated in a rotary kiln to about 2,100 ° F. After separation from excess reductant , the product pellets were found to be highly reduced and acceptably hard . A total of 140 tons of prereduced pellets with an average Fe content of 79.0 percent was produced at Minneapolis and smelted in the Bureau's experimental blast furnace at Bruceton , Pa . Two additional supplies of prereduced pellets were obtained from The Steel Company of Canada , Ltd. , Hamilton , Ontario , which contained 83.8 and 91.3 percent Fe , respectively . Smelting of prereduced pellets was compared with that of unreduced pellets obtained from The Hilton Mines , Shawville , Quebec , and from the Erie Mining Co. , Hoyt Lakes , Minn . Blast furnace tests established that a substantial decrease in coke rates and higher production result from the use of prereduced pellets .

Jan 1, 1964

By William W. Adams

The stone-quarrying industry of the United States, including such related operations as rock crushing, rock dressing, and the manufacture of cement and lime, reported a larger volume of employment in 1934 than in 1933. Reports from the operating companies to the United States Bureau of Mines showed an increase in the number of men employed, number of man-days of employment, and total number of man-hours of labor performed during the year. Moreover, the average worker had a longer period of employment during 1934, the gain amounting to 11 percent over 1933. The increase in employment was accompanied by no increase in accidents for the industry as a whole; in fact, the accident rate for 1934 was a fraction lower than the rate for 1933. In some branches of the industry the frequency of accidents increased, but these increases were more than offset by reductions in rates for other branches. Reports for 1934 were received from 1,403 active plants. The working force averaged 64,331 men for 204 days per man, and the total period of employment for all of the men was 95,258,880 man-hours. Each employee averaged 1,481 hours of work during the year. The total number of hours of labor represented a gain of more than 8 percent, and the average working time per employee showed a gain of 62 hours per man.

Jan 1, 1936

By William E. Young

There are many large rhodunite-bearing veins containing manganese in the Eureka-Animas Forks area of the San Juan Mountains in Colorado. The Sunnyside vein is the largest known vein in the area. As observed on the surface, the vein is mineralized over 8,000 feet and attains a maximum width of 200 feet. The average width of the vein and its branches and ramifications is 58 feet in the area that was mapped in detail. The weighted-average analysis of surface and underground samples from the northeastern extension of the Sunnyside vein is 8 percent manganese. Most other known veins in the area have a similar manganese content. The Hidden Treasure vein lies southeast of the Sunnyside-No Name-Mastadon vein. The weighted average of the analyses of surface and underground samples from this vein is 13 percent manganese. Exposures of the Scotia-Silver Chord vein are visible over a strike length of 4,000 feet on Treasure Mountain. Diamond-drill holes show that the vein contains 10 percent or more manganese to a depth of 400 feet. The vein has an average width of 28 feet. The Independence vein is exposed on the surface for a distance of 600 feet and has an average width of 6 feet. Three cut samples taken across the vein had an average content of 20.7 percent manganese. Sampling of the outcrops of eight veins in the Placer Gulch area also indicates manganese. Numerous other veins cropping out in the surrounding area are similar to the outcrop of the. Sunnyside vein system mineralogically and are worth investigating.

Jan 1, 1966

By O. C. Blade

The use of Diesel fuel as a source of power is continuing to increase in the United States. The latest available figures indicate that refineries are delivering in excess of 10,000,000 barrels of this type of fuel per month. Factors contributing to this increased consumption are conversions by a number of railroads from steam to Diesel locomotives and the growing use of Diesel engines in buses, trucks, tractors, earth-moving machinery, water craft, and stationary power plants. The increasing importance of Diesel fuel has led to a need for more information on its characteristics, particularly on the grades and qualities currently being marketed. To supply this information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under a cooperative agreement, are conducting annual surveys of Diesel fuels produced in refineries in this country. Samples of Diesel fuel were analyzed by the manufacturers in accordance with instructions from the Motor-Fuels Survey Panel of the Automotive Research Committee of the American Petroleum Institute. Results of the analyses were transmitted to the Bureau of Mines where the data were studied am compiled as shown in the tables of this report. The first survey was made in 1950 and was published as a Bureau of Mines report. The present report shows the results of a similar survey made during 1951.

Jan 1, 1951

By Robert T. Beckman

The results of a preliminary investigation of compressive strength versus length-diameter (L/D) ratios of potash specimens and the statistical treatment of the data are summarized in this report. The purpose of the study was to evaluate a laboratory method for obtaining estimates of the strength of potash pillars during robbing operations. The specific objectives of this preliminary investigation were to test the method and the reliability (confidence limits) of the data, and to determine the number of additional specimens necessary for given confidence limits. The specimens were taken from three sites at two mines in New Mexico. The statistical analyses included the determination of the confidence limits for the data and the number of additional specimens necessary to obtain confidence limits of ±500 and 100 psi. The testing method was found acceptable, and estimates of the comprehensive strength, within 1500 psi, could be obtained by testing about 110 additional specimens from the three sites. The compressive strength of the specimens tested fits an empirical equation of the type

Dec 1, 1963

By W. W. Agey

Past investigations on waterborne impurities in the flotation process have been concerned primarily with the treatment of specific ores with particular local waters. Although some anions and cations present in water are known to react with flotation reagents, a definitive study has not been made on the effect of such common ions upon the flotation process. This report describes the fundamental research undertaken to define and measure the adverse and/or beneficial effects of different concentrations and combinations of several common anions and cations when oleic acid is used to froth-float limestone from a pulp of quartz and limestone. Research on the effect of waterborne impurities upon the flotation process was composed of two equally important phases. The first phase comprised development of a procedure for floating limestone from quartz that would give the same results in test after test. Some difficulty was encountered, but once such a procedure was developed, the second phase, comprising study and measurement of the effect of various ions c on to natural water upon the flotation of limestone, was quickly completed.

Jan 1, 1963

By Elger. G. W.

The Bureau of Mines investigated preheating of continuously fed, fragmented ferrous scrap charges by furnace offgases and utilizing substitutes for imported fluorspar to condition electric steelmaking slags. Three types of continuous scrap charging procedures were investigated to determine electrical energy consumption in a I-st (short ton) electric arc furnace. Cold and preheated scrap charges were continuously fed at rates averaging 37.5 and 43.7lb/min, respectively. The feed rate varied appreciably from test to test owing to hangup of the scrap in the charge bin. Approximately 7 pct less electrical energy was consumed in melting scrap preheated to 8400 to 1,1100 F by furnace off-gases than in melting cold scrap. Overall energy consumptions were 888 kW'h/st for cold scrap, 829 kW'h/st for preheated scrap" and 637 kW'h/st for conventional backcharged scrap. Stack gases from scrap preheating averaged 1200 F and a flow rate of 1,615 scfm compared with 2200 F and 1,302 sefm for cold-charged scrap. Slag conditioners tested included synthetic fluorspar, boric acid, hydroboracite, used aluminum potlining wastes and aluminum anode tailing wastes, and Sorelflux B. The boron-containing conditioners fluidized the slags the best, followed in order by the conditioners containing fluorine and titanium.

Jan 1, 1987

By R. E. Head

[Recent investigations at the Intermountain Experiment Station of the Bureau of Mines at Salt Lake City indicate that metallurgists have given little attention to the occurrence of jarosite minerals in the oxidized ores of lead and silver. These investigations have also emphasized the importance of lowing when these minerals occur in the oxidized ores, especially those containing lead, silver, and gold, as their presence is a material factor in selecting a suitable kind of treatment. Since the question of the occurrence of jarosites in oxidized ores has come to the attention of the Bureau of Mines, investigation has indicated that plumbojarosite and argentojarosite are quite common. These two minerals appear to be widely distributed and probably escaped recognition by persons who had attempted to treat certain oxidized lead ores in which the jarosite minerals represented a material portion of the metal content. Consideration of the physical characteristics of the jarosites also indicates that in many cases failure to treat some of the oxidized lead ores with success has been directly due to the fact that the greater portion of their lead and silver content was present as plumbojarosite and argentojarosite. The data and the description of these minerals given in the body of this paper indicate that attempts to recover lead and silver from ores in which appreciable amounts of too metals occur is plumbojarosite and. argentojarosite would be unsuccessful if confined to gravity methods of concentration. There are undoubtedly considerable tonnage of oxidize lead ores in the various mining regions of this and other countries, and it is quite probable tat in some of these ores the metal content of lead and silver may be largely anglesite (lead sulphate) and cerussite (lead carbonate) but that they will also contain cerargyrite (silver chloride), argentojarosite, and plumbojarosite. The treatment of such ores therefore presents an important problem, since a product is discarded from]

Jan 1, 1928

By E. H. Denny

Colorado coal-mine fatalities, which have gradually decreased since 1914, have shown a marked decline since 1924. Data on coal-mine fatalities in Colorado published by the U. S. Bureau of Mines5 indicate that the deaths per thousand 300-day workers have decreased from 9.13 in 114 to 6.14 in 1926, and that the deaths per million tons produced have decreased from 9.18 in 1914 to 4.98 in 1926. Table 1 gives fatality rates in Colorado and in the United States from 1914 to 1926 inclusive. [ ]

Jan 1, 1929

By Lance R. Barron

The U.S. Bureau of Mines (USBM) conducted ground pressure analysis of a wide abutment-type chain pillar in a two-entry gate road of a Western U.S. coal mine with an extremely weak immediate roof. About 15 m of fragile, low-strength mudstone lies between the seam and the lowest competent roof member. Three-and two-entry gate road designs with several pillar sizes and various secondary support systems have been employed to improve tailgate-entry stability, with varying results. This report discusses gate road layout and performance and secondary support effectiveness. The results of the pillar pressure study are compared to pillar loading predicted by a widely used pillar design method and to similar studies in other mines. A stability evaluation of the most recent longwall headgate, using the USBM Analysis of Longwall Pillar Stability (ALPS) method, indicates marginal stability in first-panel mining and instability in second-panel mining. The ALPS method and the USBM Coal Mine Roof Rating system are used to evaluate tailgate-mining stability of the previous gate roads and to determine pillar and entry width and top coal thickness criteria for tailgate stability in future panels.

Jan 1, 2010

By M. L. Glenn

The Bureau of Mines is conducting research on substitutes for chromium-containing alloys in order to conserve imported critical and strategic materials. Part of this research concentrates on finding low-chromium substitutes for heat-resisting stainless steels for the temperature range 600° to 800° C. Ferritic alloys are emphasized that have oxidation resistance provided by chromium contents as low as 10 pct and stress rupture strength provided by the precipitation of the chi(X)-phase intermetallic compound, (Fe36Cr12 (Mo, Ti)10). Initially, research was concentrated on selecting an alloy composition having a minimum chromium content with strengthening provided by the X-phase. An Fe-(10-12 pct)Cr-6 pct Mo-(1.5-2.0 pct)Ti alloy was selected. After the alloy selection, the tensile, stress rupture, and oxidation properties were determined. Stress rupture properties were found to be similar to those of 304 stainless steel. However, the alloys possessed brittleness during both stress rupture and tensile testing, possibly as a result of too high a content of molybdenum and titanium. Higher than expected oxidation rates were found that may be caused by the high molybdenum content.

Jan 1, 1984

By W. S. Landers

Nine high-volatile bituminous Utah coals were carbonized singly and in blends with low-and medium-volatile bituminous coals. Of the 9 coals, 2 are in commercial use as the base coals in blends that produce industrially accept-able metallurgical coke, while 7 are regarded as weakly coking and are not used commercially in coking blends. The carbonization tests were made in a la-inch diameter, cylindrical retort, using 50-pound charges. Sunnyside coal blended with autogenous char generally produced larger and stronger coke than was yielded by straight Sunnyside coal. The volatile matter of the char and the concentration of the char in the blend appear to be important parameters influencing coke size and strength. A blend of 10 per-cent autogenous char of 7.2-percent volatile matter with Sunnyside coal yielded coke that was larger, stronger, and of higher apparent specific gravity than coke produced from an industrial coke oven blend consisting of 15 percent medium-volatile coal and 85 percent Sunnyside coal.

Jan 1, 1967

Reduce the potential of haulage related injuries in underground mines by providing a method for quickly assessing the state of repair of mine haulage track. The Problem Currently, there are no established standards or procedures for inspection or cleaning of underground mine haulage track. Many track defects are hidden from an inspector because of layers of dirt and debris on the ballast, spikes, fishplates, etc. When a visual inspection can be performed, it may be highly subjective, except for a few items that can be categorized or counted, such as missing bolts or spikes. Track inspectors may even become tolerant of defects that can gradually worsen. For these reasons, mechanical inspection methods are needed to supplement visual inspections. Approach The Bureau investigated this problem and designed a towed vehicle to both mechanically clean and inspect underground coal mine haulage track. The vehicle was developed using a systems approach, paying particular attention to human factors issues such as operator field of view, operator ingress-egress, control positioning, and seating design. The prototype was built using simple fabrication techniques and off-the-shelf components.

Jan 1, 1990

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By J. W. Paul

This circular is one of a series of reports on coal mining methods and cost s which are being prepared by the U. S. Bureau of Mines for the purpose of making available to those interested in the industry a knowledge of the mining methods employed in mines where mechanical and hand loading is practiced and the cost data on the several operations pertaining to the removal of coal from the working faces and its transportation to the tipple for loading into railroad cars. The methods employed are influenced by the natural local conditions with respect to the thickness and character of the coal beds and the overlying strata, the means employed for roof support and its control, and the disadvantages incident to the development of mines in thin coal beds.

Jan 1, 1929

By Parry. V. F., W. S. Landers

"INTRODUCTION Approximately 1,250,000 tons of 2-1/2-inch and 1-1/2-inch slack, representing over half of the output from 40 to 50 mines, is produced in the Denver region each year. Part of this slack is made by crushing lump, and some of it is rescreened to make pea and modified pea sizes measuring 1-1/2 inches by 2-1/2 inches and 3/4-inch by 1-1/2 inches, round-hole. Modified pea is popular as domestic stoker fuel. Approximately 900,000 tons of slack 0 by 2-1/2 inches, 0 by 1-1/ 2 inches, and 0 by 3/4-inch in size are consumed by industrial plants, the principal consumers being a large power plant and the beet-sugar industry. The power plant uses annually 250,000 to 275,000 tons of pulverized fuel and can pulverize slack of any size, while the sugar factories consume about the same quantity of coal in stokers. The sugar factories store about 110,000 tons of 2-1/2-inch slack under water from January to October, and burn the remainder of their consumption directly during the campaign season from October to December. For this purpose, sugar-factory power plants can use any size of slack, which is recrushed to pass a 3/4- or 1/2-inch screen before burning on chain-grate stokers. About one-third of the 2-1/ 2- inch slack produced in the field is used in smaller industrial plants that employ stokers.Certain factors affect the utilization of 2-1/2-inch slack in the Denver region. The increasing production of hydroelectric power has reduced the consumption of coal at power plants slightly. If more hydropower is generated, the trend of consumption of slack might be downward, unless industrial activity offsets this greater output. Rapid increase in number of domestic stokers during recent years has necessitated preparation of greater quantities of stoker coal, with the result that more lump is crushed, and preparation facilities are changed. At present about 19 percent of the coal produced is crushed to meet the constant demand for industrial fuel as well as the increasing but variable demand for the small domestic stoker sizes. The quantity crushed has increased 12 percent during the last 6 years. These factors are shifting constantly. The trend toward the use of clean and smaller sizes for domestic stokers gives a slack having a larger proportion of fines. In future, even greater quantities of small stoker coal probably will be prepared, and the resulting greater quantities of small slack will have to be used for industrial purposes."

Aug 1, 1942

By Arthur B. Johnson

The Bureau of Mines investigated the concentration characteristics of high-clay sylvinite ores from four potash companies operating in the Permian Basin near Carlsbad, N. Mex. These ores, containing 13 to 22 percent K20 and 3 to 7 percent clay slimes, cannot be effectively processed by current commercial flotation methods because of their high slime content. A solution to this problem was shown to be the use of two-stage moderate scrubbing conditions and washing of the ore as opposed to strenuous attritioning. Bench-scale physical beneficiation techniques for recovering potash minerals and the development of ore-dressing systems by flotation resulted in obtaining acceptable product grades and recoveries. By using a coarse grind, emphasis was placed on production of premium granular and coarse products. Flotation results showed that concentrates of 58.7 to 60.4 percent K20 with recoveries of 71.0 to 83.4 percent 0f the K20 values can be obtained.

Jan 1, 1971

By C. J. Walker

The ever-increasing use off natural underground formations for storing natural gas has focused attention on the behavior of such storage formations under varying operating conditions. The need for a means of evaluating in¬dividual wells and groups of wells has become manifest. It is essential that industry and others be able to determine the rates of flow that can be ex¬pected from a given well or group of wells under different conditions and to ascertain whether certain wells are deteriorating. Such questions need more exact answers now than ever before because of the vital role underground gas storage plays in the industrial and domestic consumption of natural gas. The Bureau of Mines--in cooperation with the American Gas Association--has main¬tained an active interest in gas-well testing because of the implications of such test procedures on the consumption and efficient production of natural gas. A basis for testing gas wells was provided by the back-pressure method of Rawlins and Schellhardt (12).4/ They showed that for normal gas wells there is a consistent relationship between rates of delivery of gas and corresponding pressures when the formation pressures are used as the basis of interpretation, The equation for this relationship is as follows: Q = C (Pf2 - Ps2)n where; Q = rate of flow, generally expressed in cubic feet per 24 hours. C = a coefficient.

Jan 1, 1960

By Dean H. Ambrose

Using three-dimensional (3-0) graphics computing to evaluate new technologies for computer-assisted mining systems illustrates how these visual techniques can redefine the way researchers look at raw scientific data. The U.S. Bureau of Mines is using 3-D graphics computing to obtain cheaply, easily, and quickly information about the operation and design of current and proposed mechanical coal and metal-nonmetal mining systems. Bureau engineers developed a graphics simulator for a continuous miner that enables a realistic test for experimental software that controls the functions of a machine. Some of the specific simulated functions of the continuous miner are machine motion, appendage motion, machine position, and machine sensors. The simulator uses data files generated in the laboratory or mine using a computer-assisted mining machine. The data file contains information from a laser-based guidance system and a data acquisition system that records all control commands given to a computer-assisted mining machine. This report documents the first phase in developing the simulator and discusses simulator requirements, features of the initial simulator, and several examples of its application. During this endeavor, Bureau engineers discovered and appreciated the simulator's potential to assist their investigations of machine controls and navigation systems.

Jan 1, 1992