Search Documents

By B. K. Shibler, W. G. Sandell, G. M. Potter, H. D. Snedden

"INTRODUCTION During the course of the investigation of the occurrence of manganese deposits in the western United States, examining 'engineers of the Bureau of Mines collected samples from seven manganese properties in Grand and beery Counties, Utah. These were supplemented by five samples submitted by property owners. Since all of the ores were too low-grade for use in producing ferromanganese for steel manufacture, some means of beneficiation was required to produce marketable concentrates, and metallurgical studies were made on each of the samples.Most of the ores Investigated are similar in one respect: At least part of the 'manganese oxide areas contains minute inclusions of gangue. This occurrence materially enhances the complexity of the ore, partly by .increasing the complexity of mineral association, but largely through making manganese-quartz liberation more difficult. In such ores, there is a marked tendency for the manganese minerals to be retained as shells or coatings on the surfaces of quartz particles when crushed. Particles of this type represent considerable loss of manganese in tailing, if gravity-concentration methods are employed, or tend to' float, thus carrying an appreciable quantity of gangue into the concentrate, if treated by flotation.Plus 48-percent manganese sinters were made from some of the ores tested, but, in general, intimate association of manganese minerals with silica limited the degree of beneficiation attainable."

Dec 1, 1947

By Robert E. Barieau

In the design of plants to separate helium from natural gas, it is necessary to estimate the enthalpies of the various streams at various positions in the process. This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities. The minimum information required for developing an enthalpy diagram is presented, and the relative merits of the various methods are discussed. It is concluded that methods that require no mass flow rate or energy measurements are to be preferred.

Jan 1, 1965

By W. W. Agey

Under terms of cooperative agreements, the Federal Bureau of Mines Inter-mountain Experiment Station assisted the General Services Administration (GSA) in operating the manganese-ore purchasing depots at Deming. N. Mex., and Wenden, Ariz. A resident metallurgist stationed at the depots directed sampling of the ore lots for assaying, took samples for amenability testing, calculated acceptances for payments to shippers, and served as technical adviser to the depot manager. The Intermountain Experiment Station at Salt Lake City, Utah, tested the amenability of the ores to determine how much of the manganese could be recovered in concentrates assaying a minimum of 40 percent manganese (Mn) and containing a maximum of 16 percent iron (Fe), 15 percent silica (Si02) plus alumina (AI203), 0.3 percent phosphorus (P), and I percent copper (Cu) plus lead (Pb) plus zinc (Zn). All chemical analyses of the ores and test products were done at Salt Lake City. In all, 567 ore lots submitted to the Deming depot were tested by flotation to determine their amenability to concentration into specification-grade material; 421 lots were amenable, and 146 were unamenable, primarily because of high copper content or excessive silica or iron in the flotation concentrate. Chemical analyses totaling 42,700 were made on the ores submitted to the Deming depot and on the products of the amenability-test program.

Jan 1, 1959

By M. J. Pazuchanics

This U.S. Bureau of Mines report presents results from an ongoing investigation of the use of adaptive signal discriminating methods to distinguish between cutting coal and cutting mine rock. Bit-cutting forces and tool vibration were measured in the laboratory as a linear-cutting apparatus (LCA) made constant-depth cuts in coal, sandstone, and shale test specimens. A portion of the collected data has been analyzed and some preliminary results are given here. The influence of data bandwidth, data window size, number of signal features, and voting among classifiers on classification performance are noted. Results to date, based on ideal-cutting conditions and simple geologic materials, indicate that of the four classifiers tested there appears to be no single best classifier. Usually, classification accuracy showed slight improvement as the number of features considered for classification increased. The highest classification accuracies were achieved when voting was conducted among classifiers followed by voting among force components.

Jan 1, 1991

By D. A. Larson

The Bureau of Mines conducted research to develop preliminary engineering data necessary if the cobalt-rich manganese crusts that occur in the Exclusive Economic Zone (EEZ) of the Hawaiian Archipelago are to be mined. The research was divided into the following sections: (1) physical, mineralogical, and chemical descriptions; (2) mechanical property testing, such as compressive strength, tensile strength, and a rippability index; and (3) mechanical cutting characteristics, including average and peak cutter forces, the specific energy, and cuttings size distribution. Section 1 utilized microscope, X-ray powder diffractometer, and electron microprobe analyses. Section 2 utilized standard mechanical property testing techniques. Section 3 utilized a converted planer mill with full-size coal cutters to fragment the crust and substrate samples. The manganese crust samples were mainly manganese and iron oxides and hydroxides with an average cobalt content of 1 pct and had a nucleus or substrate of rock or sediment. The significant results shown by the mechanical property and cutting tests are that the crust and all but two types of substrates (basalt and trachyte) are weak materials and easily cut with standard drag cutters. The crusts are generally comparable to medium hard coal in strength and in their resistance to cutting.

Jan 1, 1987

By E. G. King

The Bureau of Mines made experimental determinations of the heats of formation of forsterite and chrysotile at 298.15° K. The heat capacities of two polymorphs of serpentine, chrysotile and antigorite, were measured over the temperature range from 50° to 298° K and the entropies at 298.15° K were evaluated. The heat content of antigorite above 298.15° K was measured to 850° K. These thermochemical data were combined with other pertinent data to give heat and free energy of formation values at high temperatures. Free energy values are given for the reaction, forsterite + water = brucite + serpentine at different temperatures and pressures.

Jan 1, 1967

By Clarence Karr

RESINS from a bituminous pitch, a bituminous coal, a lignite tar, a subbituminous pitch, and an electrode binder pitch wore investigated by the Bureau of Mines. The compositions of these resins were determined by four independent methods of structural detemination: (1) Molecular formula and ring analysis, including ring (2) infrared and ultraviolet spectra; (3) combined pyrolysis/gas chromatography, and (4) catalytic dehyrogenation followed by spectra and pyrolysis. The resin structure was correlated with coal structure, and it was concluded that pitch resins probably consist of essentially unaltered coal molecules carried over with the tar vapors in low-temperature carbonization.

Jan 1, 1966

By Donald S. Colby

This Bureau of Mines report is essentially a handbook, or manual, for making the type of mineral resource valuation commonly required for such public policy problems as mineral leasing. The principle of resource valuation through the capitalization of cash flow is well established. A mathematical procedure, based on a simplified accounting system, is detailed for calculating cash flow from revenue, plant costs, and operating expense. Variations of procedure cover cost depletion, percentage depletion, and depletion limited to 50 percent of net income. The influence of the depletion provisions of the tax regulations on the value of a resource to an owner and to an operator is analyzed. The relationship of royalty, bonus payments, and sales price to resource value is also described, and methods for approximating resource values using these payments as input data are developed.

Jan 1, 1969

By Larry R. Wilson

The development effort described herein was directed toward the design and development of a flexible communication system to provide two-way section communications between any telephone on an MCM-101 telephone FDM exchange and a miner provided with a uhf walkie-talkie transceiver. The system also provides normal communication between miners within a working section through the uhf coupler interface repeater.

Jan 1, 1976

By K. R. Becker

The addition of a force gage and a reaction detector to the Bureau of Mines drop-weight impact apparatus made it possible to examine the details of the force exerted on the specimen and make estimates of the time to reaction. With the current setup the force was found to be oscillatory and not reproducble. However, single well-defined pressure pulses can be delivered to the explosive sample by modifying the drop-weight tools. With a modified test arrangement, the time to reaction and the peak force and energy at the time of reaction were determined as a function of drop-weight height for several different explosives. All these parameters were found to decrease as the rate of force application was increased. The same parameters were also found to vary with the thickness of the test sample. The implications of these results are discussed in terms of practical drop-weight testing.

Jan 1, 1972

By J. D. Spagnola

The Bureau of Mines conducted research to obtain comparative data on the extent of reduction of galena and sphalerite with molecular hydrogen and with hydrogen from the thermal cracking of ammonia and methane at various time intervals. Galena reductions of 95 to 99 percent were obtained with H2 and with decomposed NH3 while reductions of 70 to 80 percent were obtained with cracked CH4? Sphalerite reductions of 99 percent were obtained at 1,000° C with Hz and with decomposed NBs; however, complete volatilization of the free zinc from the remaining concentrate and the subsequent recombination of zinc and sulfur vapors resulted. A promoted iron catalyst brought about a decrease of 100° C in the temperature required for complete decomposition of ammonia. It was found that H2S retards NB3 decomposition and that nitrogen retards the reduction of galena by H2? A mixture of N2 and He in about the same ratio as that obtained by the thermal cracking of NBs gave about 15 percent less reduction of galena than was obtained with decomposed NB3; this indicates that a portion of the hydrogen obtained by NBs decomposition is in an active form.

Jan 1, 1965

By S. L. Windes

For a number of years, the Bureau of Mines conducted tests on various types of structures to determine the effect of seismic vibrations emanating from quarry blasting in an effort to determine an index of damage . Associated with these tests , occasional records were made of the characteristics of. the air blast or concussion from the explosions . Although the importance of the air - blast problem was recognized , the equipment was not designed for air -blast measurements , nor was the early research program concerned with the problem . After the ground - vibration tests had been completed , attention was turned to study of the air blast and its effect . The air - blast problem in reference to quarry and mine blasting may be divided conveniently into three phases : (1 ) Determination of the fundamental characteristics of the air blast , such as the pressure - time relationship , speed of propagation, attenuation , and the like ; ( 2) effect of blasting conditions on these air -blast characteristics ; and ( 3) determination of the conditions necessary for damage to structures . The initial step was the development of microphones suitable for recording the anticipated blast pressures. Such microphones were designed and built during 1940 , and described in technical detail for publication ( 2)3/. Briefly, the microphone adopted was a small, plate - diaphragm condenser type . The recording was through special transducer amplifiers with low -frequency response to zero cycles per second and a Duddell - type oscillograph of special design .

Feb 1, 1942

By A. B. Needham

Graphite is a raw .material of considerable importance in both waxy and peace. Two types of graphite, classified according to particle size as flake and fines, are used, but the former is in much greater demand. The principal wartime use of graphite is in the manufacture of crucibles for melting brass and special alloys of copper and steel. Other uses in both peace and war are as lubricants, for foundry facings, and in paints, electrodes, batteries, motor and generator brushes, and a variety of other commodities. . This paper describes the operations of the Southwestern Graphite Co. of Los Angeles, Calif., which produces both flake and fine graphite from a property in Burnet County, Tex.

Jan 1, 1946

By K. R. Van Doren

The polynomial method for estimating virial coefficients from experimental data suffers from three serious defects: (1) There is no known relationship between the polynomial coefficients and the virial coefficients, (2) the values of the estimates depend upon the degree of the polynomial and the particular set of values used for the independent variable, as well as the random errors in the dependent variable, and (3) the variances calculated for the estimates do not represent the mean square errors of estimation. Attempts to overcome these defects have thus far been unsuccessful; these attempts have also failed to account for the fact that none of the virial coefficients are uniquely determined by the values of the dependent variable for a finite set of values of the independent variable. The conclusion is that virial coefficients cannot be reliably estimated from experimental data unless additional information about the virial expansion itself, such as its rate of convergence, is available.

Jan 1, 1969

By Ernest E. Berger

"INTRODUCTIONOne of the outstanding problems in the normetallic industries, and one which involves two of the greatest of these industries, cement and gypsum, is the reaction of Portland cement with calcium sulphate. To all Portland cement clinker there is added in the manufacturing process, a small amount of retarder, as a necessary ingredient of the finished product. This retards the initial set, increases the strength, and adds to the plasticity of the cement so it will have the desired working and setting qualities. The retarder commonly used is gypsum, (CaSOA.2HO), which is the hydrous form calcium sulphate. Calcium sulphate is also available as plaster of Paris (CaSO4 1/2 HC) and anhydrite (CaSO4). The purpose of this inquiry was to determine the form or mixture of forms best adapted for retarder. The problem is complicated by the fact that cement clinker is a complex mixture of calcium silicates and aluminates, and that clinker from different mills, making cement of approximately equal quality, differs considerably in chemical constitution. Thus the same retarder may give very different results with different types of clinker, especially in the percentage of retarder required for the same degree of retardation.It has been known for some time that a small percentage of plaster of Paris will greatly retard the time of set of Portland cement as well as increase its strength and plasticity, but whether gypsum and anhydrite will have a similar effect is as such disputed question. The offects of gypsum have received little consideration in laboratory research because, even though it will not retard a clinker when the two are mixed in the laboratory, as has been noted in some instances, the cement will have a normal set when the two arc mixed in the large tube mill at the plant, so that practically, gypsum seems to be equally as goou as plaster of Paris, and because of the great saving in cost it has been used almost exclusively."

Sep 1, 1925

By Graham W. Marks, Betsy M. Jones

"Recently4/ it was shown that the total energy method5/ of spectrochemical analysis is suitable for the quantitative estimation of many of the elements of which ores are composed. It was shown how this method can be applied to the determination of germanium, tin, and lead. Continuing this work, the present report deals with analyses for beryllium, zinc, cadmium, and indium.There are three basic problems in these investigations. The first is to study the influence of those elements that make up the greater part of an ore sample on the spectral-line intensities of the elements for which analyses are being made, the latter generally being the minor constituents. The second is to develop proper methods for the preparation of standard spectrographic curves. Finally, we are concerned with improvement in equipment and procedure, so that greater accuracy can be achieved.As discussed previously, it is better to study as groups those elements that belong to the same group in the periodic table because their spectra are similar. Beryllium, zinc, and cadmium are thus related. Indium was included in this work because it is associated with zinc and cadmium in zinc ores.The authors wish to acknowledge the valuable assistance of the staff of the Bureau of Mines Analytical Laboratory who made the chemical analyses and supplied the ore samples used in this work.A brief description of the procedures followed in making the standard curves and analyses is given below; a detailed discussion will be found in an earlier paper.6/Basically, the procedure for determining a standard curve consists of two parts: (1) Choosing a suitable line in the spectrum of the element to be determined and (2) determining the variation in the intensity of this line with the amount of the element burned in the arc."

Nov 1, 1948

By Howard P. Hamlin, John W. Sweeney

Shales , clays , and loess in Iowa were tested and evaluated to determine feasibility of producing lightweight aggregate by commercial rotary - kiln or sintering methods . Preliminary testing was conducted in a muffle furnace . Rotary - kiln tests were conducted in a 16 - inch by 14 - foot rotary kiln . Concrete cylinders and cubes were tested to determine qualities of the aggregate . Three samples made suitable lightweight aggregate by rotary - kiln methods and two by sintering .

Jan 1, 1964

By L. F. Heising

The Bureau of Mines evaluated 42 composite samples from selected Michigan-Wisconsin iron formations by reductive roasting-magnetic separation and flotation at minus 325 mesh. Samples having poor to marginal response on initial examination by conventional methods were reevaluated by finer grinding, by reagent suite modifications, and by selective flocculation-desliming techniques. Results ranged from excellent on Menominee Range samples to relatively on Gogebic Range ores. Marquette Range samples ranged from responsive to nonresponsive, depending upon grain size and mineral association.

Jan 1, 1967

By Allen D. Look, Norman King

For many years, much thought and effort have been devoted to the achievement of safety in the use of explosives by those interested in the preservation of human life and the protection of property. As a result, we now have adequate rules pertaining to the safe use of explosives , which, if observed, would prevent many, perhaps ail , of the explosives accidents that yet occur . Although the rules respecting the use of explosives are believed to be well - known, many accidents occur because they are disregarded . The mental awareness aroused by a tragic accident usually will cause safety precautions to be taken for a while ; however , this awareness gradually disappears unless a sincere effort is made permanently to prevent similar accidents . Frequently, because safe methods are more irksome than unsafe methods , the lessons taught by accident experience are forgotten in a short time , vigilance is relaxed , and there is a gradual return to unsafe , easy methods of performing work. If the preservation of human life is important , the unfortunate experiences of others and the lessons taught by them should be applied to reduce unnecessary loss of life . The value of a life lost as the resuit of accident should be calculated not only from the monetary and humanitarian standpoint but also according to what the accident could contribute in the way of saving other lives and suffering . This saving of other lives can and will , if the lessons from unfortunate accidents are applied , convert a loss to a gain a gain of such magnitude that the accident victim could be considered

May 1, 1944

By Paul M. Tyler

Bismuth is a useful metal and rather an uncommon one . The element probably constitutes much less than one-millionth part of the earth's crust , but the potential supply - to no small extent as a by-product of the production of lead and copper with which it is associated in nature has tended for many decades to exceed the demand. A single mine in Bolivia could readily flood the world's markets , and considerable quantities of bismuth are allowed to escape recovery at many smelting plants .

Jul 1, 1931