Search Documents

By John R. Shattuck

The Shasta and California Iron-ore deposits are 14 miles northeast of Redding, Shasta County, Calif.; and since 1907 have produced more than 300,000 short tons of exceptionally pure iron ore. Although some ore was mined and smelted from 1907 through the First. World War, most of it has been produced from 1942 through 1945 for use in making heavy ship ballast and concrete anchorages for mines. Irregular masses of magnetite, ranging from lumps of a few tons to pods containing about 25,000 tons, occur associated with skarn near the contact between the McCloud limestone and a younger granitic intrusive. Some of the deposits are low-grade, whereas others are nearly pure magnetite. Selective mining and hand sorting are necessary to produce a high-grade product. Investigation of these deposits by the Bureau of Mines included 2,910 feet of diamond drilling, some surface sampling of the principal mineralized zone and beneficiation tests. Resulting factual data are given in the body of this report.

Jan 1, 1948

By O. C. Blade

A summary of the characteristics of motor gasoline for the summer 1951 is presented in table 1, and for comparison, a similar summary for the summer 1950 is shown in table 2. Trends of some of the more important characteristics over a period of years are shown in figures 1 and 2. As indicated, octane numbers of motor gasolines sold in the United states decreased approximately one-half to one octane unit from the record levels attained during the winter of 1950-51 and are a little below the octane numbers of summer 1950. However, average vapor pressures of the summer gasolines did not change, and certain distillation temperatures varied only slightly from those of the year before.

Jan 1, 1952

By J. R. Bartels

The U.S. Bureau of Mines has established a wire rope research laboratory to examine the factors that affect the life of wire rope. Two sin-diameter 6x25 fiber core (FC) ropes were degraded on a bending fatigue machine, These were the second and third ropes in a series of tests on this construction and size rope. Tensile and nondestructive tests were performed on samples of the rope to determine the relationship between rope deterioration and rope breaking strength. The tests indicated that once a wire rope nears the end of its service life, both deterioration and the consequent loss of rope strength begin to increase at an accelerated rate.

Jan 1, 2010

By Robert C. Hickman, Xavier B. Starnes

"The general location of the Kentucky, Fluorspar District and the Moore Hill fault area are shown in figure 1. An engineer3/ the Bureau of Mines visited the district in July 1942 and reported on the Moore Hill fault system. Subsequently the Bureau explored the Summers, Pepperbox, McCune, Eagle-Watson, Henry Watson, Davenport, Felix Tyner, and Eagle-Wring prop¬erties by core drilling. These properties and the principal faults are shown on figures 2 and 3.Collaboration of the Federal Geological Survey4/ was of great benefit, particularly in mapping the properties, determining the stratigraphy, and furnishing information on that and other geologic factors.Fluorite was noted as early as 1818 near Shawneetown in southern Illinois.5/ In 1835 an attempt was made to work deposit in Crittenden County, Kentucky, but interest centered chiefly upon the galena found with the fluorite. The first shipments of fluorspar from Kentucky wore made in 1373 from the Yandell mine of Crittendon County.6/ It is not known when the first work on the Moore Hill fault was done, but it seems probable that the Cullen-Eagle and Nancy Hanks were being ,worked in 1900. Gravel spar was found on the surface at the Two Brothers mine in 1904,7/ and the main shaft was started in 1914; work also began at .the Davenport in 1914, and in 1917 the Eagle-Watson was in production. A shaft was gunk on the Pepperbox in 1918, and in 1922 fluorspar was found and work was started on the Summers property. In 1924 work began at the McCune, Felix Tyner, Eagle-Wring, and probably the Hicks properties.No Good approximate record of production from each property on the Moore Hill fault system is obtainable, but an estimate based upon all data available is as follows:"

Sep 1, 1946

By Ralph V. Higgins

The present methods of appraising the long-range performance of oil reservoirs are based upon physical properties of the crude oil and the permeability of the reservoir rock. By means of these methods the performance of a reservoir may be estimated throughout its entire life. Before these methods were used, the future performance was estimated mostly by extrapolating pressure-decline curves -a method that is satisfactory for extrapolating only for a short period into the future. One factor that affects satisfactory long-range prediction of reservoir performance is the extent to which small changes in the physical properties of the oil and differences in the choices of relative permeability influence the calculated oil recovery. Selection of the physical properties of the samples to represent those of the oil and rock for the entire reservoir is difficult. This report is concerned with the error in calculated recoveries that may result from these inherent difficulties.

Jan 1, 1956

By Van H. Manning

"Under the organic act establishing it, the Bureau of Mines is authorized to conduct investigations designed to improve health and safety conditions in the mineral industry and to promote efficient development and utilization of our mineral resources. The field of the Bureau's activity, therefore, begins with the commercial development of mineral deposits and ends with the production and utilization of the final marketable product.In order to serve more efficiently the various sections of the country, the Bureau has established, in addition to its main offices at Washington, D. C., eleven field experiment stations, three field offices and several mine rescue cars and mina rescue stations. These field branches are so distributed as to cover most of the mining districts of this country, including Alaska. The field service in general deals with specific experimental problems, cooperative work with non-governmental institutions, and mina rescue work, while the Washington office is the administrative head and is responsible for the distribution of general information, the chiefs of the technical and administrative divisions of the Bureau being stationed there.The Bureau is prohibited by law from doing work exclusively for the benefit of any private company or individual. Generally speaking, the Bureau does no assaying, ore testing, or similar service work for the benefit of private companies or individuals. In response to requests for work of this sort a list of assay and ore testing laboratories is supplied. In referring inquiries to com-mercial laboratories or consulting engineers, care is taken to mention several names so as to avoid designating any one establishment or engineer."

Apr 1, 1920

By d&apos, Dennis V. Andrea

The Bureau of Mines and El Paso Mining and Milling Co. conducted a cooperative in situ leaching research program at the Emerald Isle mine near Kingman, Ariz. The objective of this research was to develop in situ leaching methods for 200,000 tons of ore exposed in the pit bottom and also 3,000,000 tons of ore under 200 feet of overburden adjacent to the pit. The research included core drilling for fragmentation analysis, inplace permeability testing, seismic surveys, blasting tests, blast vibration measurements, inplace leaching, and ground water monitoring. A l5,000-ton test area in the pit bottom was blasted and leached inplace for 117 days. This successful test was followed by leaching 100,000 additional tons of unblasted pit bottom ore. Two test blasts, under 205 feet of overburden and extending to 290 feet, were detonated in an area near the open pit. The second blast was detonated because the first blast did not create adequate permeability for leaching. Pit bottom leaching was discontinued and the test area under 200 feet of overburden was not leached because the company terminated operations at the Emerald Isle mine. Based on the research completed, an expanded in situ leaching system was designed, but not implemented, to recover copper from a 1,500,000-ton area at the Emerald Isle mine.

Jan 1, 1977

By Timothy M. Barton

The U.S. Bureau of Mines is conducting research to assess the effectiveness of different chain pillar designs in maintaining gate entry stability. A particular concern is ground control for deep-cover 1ongwalls located at depths in excess of 1,000 ft. The study described in this report was performed in two experimental sections in one longwall headgate section which contained three different pillar designs. Two of the designs used conventional abutment pillars, while the third was a total-yielding pillar system. Both of the test areas were located under 1,800 ft of cover. The purpose of this study was to evaluate the effectiveness of these three pillar designs for gate road stability. As the longwall mined passed the test areas, Bureau engineers monitored entry convergence, roof sag, and changes in roof quality. The study indicated that the all-yield system performed nearly as well as the better of the two abutment pillar systems; but all of the three designs would have failed to provide acceptable stability for second panel mining without considerable artificial support.

Jan 1, 1989

By R. H. Fewkes

New information on possible resource value of sea floor manganese nodule deposits in the eastern North Pacific has been obtained by study of records and collections of the 1972 Sea Scope Expedition. Nodule abundance (percent of sea floor covered) varies greatly, to judge from bottom photographs from 8 stations and data from other sources. All estimates considered reliable are plotted on a map of the region. Similar maps show the average content of Ni, Cu, Mn, and Co at 89 stations from which 3 or more nodules were analyzed. Variations in nodule metal content at each station are shown graphically in an appendix, where data on nodule sizes are also given. Results of new analyses of 420 nodules from 93 stations, for Mn, Fe, Ni, Cu, Co, and Zn, are listed in another appendix. Relatively high Ni+Cu content is restricted chiefly to four groups of stations in the equatorial region, where group averages are 1.86, 1.99, 2.47, and 2255 weight percent. These and a few other areas may warrant more exploration. It is hoped that this report will stimulate new interest in North Pacific nodule deposits and that the maps and quantitative data will aid future exploration.

Jan 1, 1981

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 4,954 samples, representing the products of 93 companies. The samples were collected during December 1955, January and February 1956. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers. The data were obtained by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation. A list of the National Motor Gasoline Survey reports published during the post 10 years is given on page 5.

Jan 1, 1956

By J. M. Mutmansky, C. Lee

"IntroductionRecognition of Coal Workers' Pneumoconiosis (CWP) as a major occupational disease has affected various aspects of the coal mining industry in the United States as well as in almost all major coal producing countries, Regulations related to the control of coal mine dust forced mine operators to modify their mining and ventilation practices. As the coal production record of the last 15 years shows, this had both direct and indirect impacts on the productivity and production costs.To identify the causes of CWP, many research efforts have been made throughout the world. Most of these studies were epidemiological in nature, attempting to pinpoint exposure and seam variables that affected the incidence of the disease. Other studies have been oriented toward the elemental and mineralogical composition of the coal dust in the mine atmosphere and in the miners' lungs. These studies indicate that there may exist some relationships between the characteristics of the coal mine dust and the prevalence of the disease. Some of the variables that are thought to affect the occurrence of CWP are the mass of the dust in the working place, the rank of the coal, the existence of certain trace elements, the free silica content of the coal, and the existence of other minerals in the respirable dust. A more complete description of these previous research studies has appeared elsewhere (Mutmansky and Lee, 1984).The behavior of particles in the human lung is known to be governed by their aerodynamic diameter, which is defined as the diameter of a hypothetical spherical particle with unit density that exhibits the same settling velocity as the given particle. Because of this fact, the aerodynamic size distribution of coal mine dust is one of the parameters to be determined along with the other physical, elemental, and mineralogical characteristics. The objective of this paper is to establish a strategy for providing coal mine respirable dust samples for characterization purposes using instruments that classify according to the aerodynamic diameter. In addition, several findings concerning characterization methods will be presented"

Mar 1, 1989

By William P. Diamond

In this U.S. Bureau of Mines study, production trends have been analyzed for 82 gob gas ventholes on 7 longwall panels in the Lower Kittanning Coalbed, Pennsylvania. Cumulative production from individual holes was found to vary considerably, ranging from 0.03 x 106 to 10.1 x 106 m3. Peak production rates were generally about 0.03 x 106 to 0.06 x 106 m3/d, but rates over 0.10 x 106 m3/d were observed. The variability of gas production from individual holes can be attributed to' several factors, including completion practices and problems, the extent of fracture development in the strata above the extracted panel, water production, and location on the panel. Of particular significance is hole location. Holes on the ends of the panels, where overburden strata are in tension because of the support of the surrounding pillars, were generally the highest and longest producers. This observation led to the experimental placement of gob gas ventholes in the zone of tension along the margin of a panel, instead of in the traditional centerline location, which is in compression. Analysis of 7 months of gas production data indicates that the experimental near-margin holes produced 77 pct more gas than did centerline holes on the same panel.

Jan 1, 2010

By Bertrand L. Johnson

Pure talc is a hydrous magnesium silicate (Mg3Si4010(OH)2). Pyrophyllite, although it resemble: talc in certain physical properties and uses, is a hydrous aluminum silicate (Al2Si4010(OH)2) - like kaolin, except that kaolin has a somewhat different composition (Al2Si205(OH)4) and structure. Soapstone can be considered essentially an impure talc grid when pulverized is used for many of the same purposes as talc. Massive, compact varieties of talc often are called steatite. PROPERTIES Talc and pyrophyllite are characterizes; by their softness (hardness on Mohs' scale, 1) their greasy feel, pearly luster, white color, and perfect basal cleavage. They have similar crystal structures, and this similarity explains the close resemblance of the two minerals in physical acid chemical properties. Talc is a good electrical insulator, resists the action of most acids and alkalies, and has an exceptional heat-retaining capacity. Its specific gravity is about 2.7.

Jan 1, 1939

By Dana C. Reinke, David K. I Ingram

Researchers at the National Institute for Occupational Safety and Health partnered with the water well industry to develop engi­neering control technologies and training products to address noise exposure at the job site. Noise­induced hearing loss continues to be a problem in the well drilling industry. Research con­ducted by NIOSH found that air rotary drill rigs produce sound levels more than 90 dB(A) over the course of an eight­hour workday. Sounds levels above 90 dB(A), identified during hammer drilling and the hammering of casing, exposes workers to levels that can damage hearing. A typical air rotary drill rig provides no barrier, for noise and dust pro­tection, between the drill’s control panel and the drill stem. The development of a partial cab is the clearest example of NIOSH’s research partnership with the water well industry. NIOSH researchers determined that an engineering noise control to protect the oper­ator at the rig’s control panel would be effective, based on typical work site conditions. Many surface rigs do not have full cabs as a result of the original equipment manufacturer design or the high cost of aftermarket products. Developed as a partial cab, the NIOSH engineer­ing noise control design addressed stakeholders’ needs associated with cost, transport, and worker usage (Figure 1). Field tests found the partial cab effective in reducing sound levels at the rig’s control panel, a typical location for a drill rig operator. Sound levels at the control panel were reduced from 104 to 96 dB(A) (Figure 2). Coupled with continued use of personal protective equipment, such as hear­ing protection devices, the partial cab can help to reduce noise exposure. NIOSH researchers created a CD with informa­tion about noise exposure and the partial cab. Most important to well drilling companies is information on how to construct and attach the partial cab to drill rigs. The CD can be viewed on a standard computer and includes a video of the partial cab in use on a work site. Computer­aided design drawings are included on the CD and provide detail of the cab design as well as information on construction mate­rials and design details. Additionally, the CD provides background infor­mation on noise­induced hearing loss and hearing protection devices to increase knowledge about this occupational health concern. This information can be viewed by all company employees to help promote the partial cab’s importance to workers using the cab. More information on the partial cab noise control technology can be downloaded from www.cdc.gov/ niosh/mining NIOSH researchers also examined the health and safety training needs of workers in the ground water industry. It was quickly realized that most workers learn health and safety on the job and do not attend any sort of formal training. In addition, there is not a lot of time for daily “tailgate talks” or “shop talks” on health and safety issues. As a small business industry, the owner is often operating a drill rig along with his other employees. In general, new employees learn the job in an apprentice style sys­tem. As a result, workers and owners have few opportunities to access uniform health and safety information based upon the job — an outdoor work environment with daily change in work sites. With this information, NIOSH researchers devel­oped two products that deliver health and safety information to fit into the daily work of well drillers. Both are information circulars and are available through download at www.cdc.gov/niosh/mining and the NGWA Web site at www.ngwa.org/publication/ publications.cfm. These circulars are: Water Well Safety Bits. This booklet provides information in a “quick bites” style. It is pre­sented in a magazine format and can be left on

By D. Harrington

We Americans pride ourselves that ours is the greatest, most advanced and most civilized nation in the world, yet statistics indicate that apparently we have little appreciation for the lives and limbs of the people whose efforts give us whatever greatness we possess. The latest available statistics indicate that the annual accident death rate per 100,000 of population is nearly 80 or far higher than that of any other country in the world except Chile; is more than double the rate in Hungary, Netherlands, Ireland, Belgium, Denmark, Italy, Germany, Norway, Sweden, and Finland; is nearly double that of England, Wales, the Union of South Africa, New Zealand, Japan, Australia, and Scotland; and is 25 to 40 percent greater than Switzerland, France and Canada. To make matters worse, from the viewpoint of mining; the latest available statistics give mining by all adds the worst accident rate of the major industrial occupations in the United States, the accident severity rate for mining in 1935 being listed by the National Safety Council as 10.14, the next highest rate being 4.52 for construction, and the average rate for 30 main industries being 1.58. IMPROVEMENT IN SAFETY RECORDS Offsetting to a slight extent this rather dark picture is the fact that starting about 1930 the mine-accident rate in both coal and metal mining began to fall, reaching an all-time "low" in metal mining in 1932 and in coal mining in 1933. It now appears probable that the year 1936 has again lowered the accident rate in coal mining and this, together with the fact that the years 1933, 1934, 193 5, and 1936 all set much lover accident rates in coal mining than ware achieved for any similar previous period, gives hope that the trend is definitely in the right direction, though from the above figures mine-accident severity has a long, tedious road to travel before it becomes as low as the severity rate of all other major industries in the United States.

Jan 1, 1937

By Terry J. Close

At the request of the Idaho Congressional Delegation, the U.S. Bureau of Mines Western Field Operations Center investigated the mineral resources of the 140,000-acre Red Mountain roadless area, located northeast of Lowman, in central Idaho. The area includes U.S. Forest Service Red Mountain RARE II area (4-063). The highly mineralized road less area is underlain mainly by granitic rocks which are transected by a northeast-trending fault system. Associated with the granitic rocks and fault system are gold and black sand mineral resources. At least 1,395 ounces of gold and 858 ounces of silver have been recovered from six lode and placer mines within the roadless area. A total of 525 tons of columbium-tantalum, 2,049 tons of euxenite, 83.5 tons of columbite, and 54,862 tons of ilmenite concentrates have been produced from a nearby black sand mineral placer. Mine workings and facilities in the roadless area consist of two dismantled mills, 15 open and caved underground excavations totaling about 2,900 ft of workings, seven large pits and quarries, over 166 smaller dozer-and hand-dug prospect pits and trenches, and in excess of 66 drill holes. The mineralized sites in the roadless area are covered by about 690 current (1992) mining claims. About 130 individuals are holding the claims. Also within the roadless area are four patented lode mining claims. Twenty-five of the 54 mineralized sites identified during the study of the roadless area have, or likely have, mineral resources. One has gold and three have black sand mineral resources that are marginal or subeconomic. There also are two hot springs with thermal water resources, some veins that could be sources of decorative quartz, and dimension stone which was quarried in the past and could be again.

Jan 1, 1993

By Martin Hertzberg

The concept of limit burning velocities, formulated in an earlier Bureau of Mines report (RI 8127), is applied to the problem of flame propagation through tubes of finite size. The limit burning velocity for conductive-convective wall-loss quenching (process b) is (Su)b = [aPe,] where the proper choice of critical Peclet constant, Pe, is determined mainly by the ratio of contact-perimeter loss area to flame-zone cross sectional area. This ratio of loss area to propagation area relates to the shape of the flame front and its control by buoyancy and by boundary conditions. The comparison of (Su)b with previously defined limit velocities for systems mixed by natural convection allows one to assess the influence of tube dimensions and boundary constraints on the "true" or earthly limits for the three directions of propagation. The flame quenching caused by inert powders is shown to be similarly described in terms of a limit burning velocity, (Su)?b. The tube's surface-to-volume ratio (~1/ro) is simply replaced by the powder's surface area per unit volume of the flammable mixture. Thermal loss quenching by these "internal walls" occurs at a critical Peclet constant somewhat higher than that observed for tubes, and the problem is complicated by the finite heat capacities of the powders and particle lag effects in the flame front.

Jan 1, 1980

By Theodore Kootz

Manufacture of high-grade ferromanganese; as a rule; requires a low-phosphorus-manganese ore with 45 to 55 percent Mn, chiefly obtained in the Soviet Union, the British Dominions, and Brazil. Also, low-manganese ores have already been used for ferromanganese production, especially in North America .and Germany. During World War I, a process was developed in which a high-phosphorus ferromanganese or spiegeleisen was prepared in the blast furnace from law- or high-phosphorus manganiferous ores, then low-phosphorus manganese slag was prepared by refining under an acid slag, and this material was, worked into a low-phosphorus ferromanganese in the blast furnace.9/ Manufacture of useful manganese ores from a phosphorus-bearing spiegel with 12 to. 15 percent Mn, 4.5 percent C,, and 0.5 percent P by slagging in a refining furnace was reported by Joseph, Barrett, and Wood.10/ The spiegel was refined to 0.75 percent Mn, 3.4 percent C, and 0.45 percent P. Thereby, a slag with about 43 to 58 percent Mn and, about 10 percent Si02, was obtained. Hotter melts gave a smaller phosphorus content in the slag than cold melts. In addition, the phosphorus content of the slag varied with the manganese content of the intermediate metal.

Jan 1, 1952

By J. P. Powell

Records show that systematic water flooding was begun as early as 1935 in Greenwood County and in 1937 in Butler County. Water flooding on some earlier projects in Greenwood County were described in a Bureau of Mines Report of Investigation.2/ This report presents a discussion of 4 projects -2 in Butler County, 1 in Greenwood County, and 1 in Butler and Greenwood Counties. The location of these projects is shown in figure 1. The projects have been in operation 6 to 12 years and have recovered about 6.6 million barrels of additional oil from the injection of 84.7 million barrels of water. Three of the projects take advantage of the elevation of the nearby hilly terrain, and water from the treating ponds flows by gravity through the filters into the clear-water tanks. By utilizing gravity flow, fewer pumps and less electrical energy is required, resulting in more economical operation.

Jan 1, 1956

By E. J. Matson

Under the investigation for critical and strategic minerals the Kaiser mine, formerly the Baxter fluorspar property, in northeastern Mineral County, Nev., was explored. The work comprised excavating 32 trenches averaging 90 feet in length, 8 feet in width, and 1 1/2 feet in depth. The trenches were excavated across the strike of the ore body to enable the engineer to spot the diamond-drill holes; 7 such holes were drilled, aggregating 3,276 linear feet. A total of 20 core samples and 107 sludge samples was taken. The work under this program indicated that the fluorspar southwest of the deposit extended laterally and also at depth at least 250 feet below the 400-foot level. INTRODUCTION The Kaiser fluorspar deposit is in the northeastern portion of Mineral County, Nev. Mining was begun about 1928, and the property has been a consistent producer of both Acid- and Metallurgical-grade fluorspar. The mineralized zone has been developed along a strike length of about 2,000 feet and to a depth of over 700 feet along the dip.

Jan 1, 1957