Search Documents

By V. A. Danielson

The Bureau of Mines studied waste disposal methods a1 a coal mine in Kentucky and another in Alabama to develop cost estimates, to provide better knowledge of current practices, and to guide consideration of alternate disposal methods. Costs of the existing waste disposal systems at each mine were estimated using present-day costs of equipment and labor. Costs of waste disposal systems using alternate equipment were also estimated. Although total disposal costs were essentially the same for both operations, reclamation costs will differ because of different reclamation practices.

Jan 1, 1969

By J. P. Capp

This experiment, one of a series on underground gasification of coal, was an investigation by the Federal Bureau of Mines of hydraulic fracturing as a means of increasing the air acceptance of a coalbed to permit introducing combustion air and removing product gases. Specific objectives of the investigation included: (1) Fracturing a coalbed; (2) determining the distance the coal was physically affected; (3) ascertaining the effect of the fracture on air acceptance of the coalbed; and (4) gasifying the coal. The coal was fractured with a fluid consisting of 15,000 lb. of sand mixed with 10,000 gal. of fuel oil and 5,000 gal. of kerosine, injected at pressures up to 900 p.s.i.g. and rates up to 425 g.p.m. The oil served as the fracturing medium, and the sand as a propping agent to hold the fracture open. From the fracture point, (the place in the bed where the fluid was injected), the fracture extended 200 ft. or more along the face cleats, somewhat less along the butt. cleats, and was confined to the coalbed. At the fracture point, the bed accepted about 500 std. c.f.m. of air, which was an etghtyfold increase. Fracture effects were extensive, as airflow was noted from old mine workings and outcrops 600 to 800 ft. from the fracture point. It is probable the actual fracture was much less than 600 ft. and that normal coalbed permeability beyond the fracture limits was responsible for this flow. This indicated that effects of the fracture extended beyond the area of coal physically affected. Although no attempt was made to gasify coal more than 200 ft. away, these effects plus the natural permeability of the bed likely would permit combustion beyond the outer limit of the fracture. As these experiments continued for more than 2 years, and greater air acceptance due to the fracture was observed at the beginning of each test, it is apparent that the effects of the fracturing persist for a considerable time.

Jan 1, 1960

By Leonard Obert

Between 1927 and 1957, sodium borate minerals were mined by underground methods in the Kramer District, Kern County, Calif. In 1957, surface mining methods were initiated, and during the next two or more decades it is probable that most of the production from the district will be obtained from open pits. However, part of this borate deposit is sufficiently deep that surface mining may not be economical and, hence, at some future date underground methods may again be employed. This report was prepared to document the underground mining methods employed in the district before 1957. The general geology of the district and the detailed geology of each of four mine sites are presented, together with a mineral and mechanical description of the ore and enveloping rock. The report also describes the stoping, extraction, pillar support, methods of artificial support, and other factors that affect the structural characteristics of these mines.

Jan 1, 1962

By John P. Powell

A comprehensive study of the effects of hydraulically fracturing water-flood wells in Oklahoma has been made by the Federal Bureau of Mines. This report presents results of that study and an analysis of some of the factors governing the results of fracture treatment on waterflood properties. Originally, hydraulic fracturing was used to stimulate oil production from old wells producing by primary methods, and its application to water-flooding was regarded with skepticism by most producers. However, since 1953 the number of fracture treatments of both oil and input wells in waterfloods has increased steadily. Hydraulic-fracture treatments in waterfloods have generally been successful in stimulating production from oil wells and increasing the rate of injection into input wells. Hydraulic fracturing has enabled several producers to turn probable failures into economically successful projects.

Jan 1, 1961

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines; the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous .sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1958

By R. B. Tippin

The heavy liquid separation (HLS) process was investigated by the Bureau of Mines to develop a means of concentrating minerals from natural ores, Various spodumene ores were tested in a 0.4-inch diameter cyclone using pure tetrabromoethane (TBE) as the heavy liquid. Studies were initiated to examine the influence of (1) pulp density (2) feed grade, (3) cyclone pressure, (4) cyclone apex opening size) (5) cyclone vortex finder opening sand (6) mineral particle size on the separation efficiency. Each of these factors was found to affect the heavy liquid separation in some degree; the mineral particle size exhibited the greatest effect and the ore feed grade the least. Conditions necessary to yield an 85 percent spodumene concentrate with an 85 percent recovery were determined to be: 70 psig pressure, 10 percent solids, 0.08-inch apex opening, 0.11-inch vortex finder opening and a minimum amount of minus 200-mesh fines in the feed. Operation of multiple cyclones in series resulted in spodumene concentrates assaying over 90 percent and indicated mineral recoveries exceed-in 90 percent.

Jan 1, 1967

By B. K. Cantrell, K. L. Rubow

"The US Bureau of Mines and the University of Minnesota have developed design and performance criteria for a personal diesel exhaust aerosol sampler for underground coal mines. These are based on the premise that size can be used to separate diesel exhaust aerosol, which is mostly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. The sampler has three stages: a respirable aerosol preclassifier, a 0.8-um aerodynamic diameter inertial impactor to collect mineral dust and a final filter to collect the diesel aerosol. Using a sample flow rate of 2 L/min and gravimetric analysis to within 0.1 mg, the measure sub-0.8 um diesel aerosol has an a-priori limit of detection of 0.3 mg/m3.A miner working in an underground coal mine with diesel equipment is exposed to a wide array of pollutants from the diesel exhaust. These include CO, CO2. NO, NO2, SO2, diesel exhaust aerosol, and a variety of hydrocarbon compounds. A quantitative definition of the health risk resulting from these exposures remains elusive. During the past several years, though, progress has been made in defining the problem.Results from epidemiological studies by Garshick et al. (1988 ), animal inhalation studies by Mauderly eta). (1986), Iwai et al. (1986), and Brightwell et al. (1986) and in vitro studies by Lewtas et al. (1986) have provided sufficient data for the National Institute of Occupational Safety and Health (NOSH) to recommend that ""whole diesel exhaust be regarded as a 'potential occupational carcinogen,' as defined in the Cancer Policy of the Occupational Safety and Health Administration"" (NIOSH, 1988). NIOSH further stated that ""though the excess risk of cancer in diesel-exhaust-exposed workers has not been quantitatively estimated, it is logical to assume that reduction in exposure to diesel exhaust in the workplace would reduce the excess risk.""The Mine Safety and Health Administration (MSHA) has also been directed by an advisory committee to establish a diesel exhaust aerosol standard and to establish regulations to minimize exposure to diesel pollutants in underground coal mines (MSHA,1988). Both reports point out the need for development of measurement techniques for respirable diesel aerosol.In the past four years, the US Bureau of Mines (Cantrell,1987 and Cantrell, et al. 1987), in cooperation with Marple, et al. (1986), at the University of Minnesota's Particle TechnologyLaboratory (PTL), have studied the use of size-selective sampling techniques to measure the mass concentration of diesel aerosol in underground coal mines. Results from these studies have been used to develop design and performance criteria for a personal diesel exhaust aerosol sampler for use in underground coal mines.These criteria are based on the premise that size-selectivesampling techniques,can be used to separate diesel exhaust aerosol, which is predominantly submicron in size, from coal dust aerosol, which is mostly greater than a micron in size. In addition to the performance criteria, this paper discusses the laboratory and field test data used to develop the criteria."

Mar 1, 1992

By H. R. Babitzke

To develop alloys suitable for use at elevated temperatures, columbium and tantalum were combined with tungsten, hafnium, vanadium, zirconium, and titanium, and the resulting alloys were evaluated with respect to fabricability, hardness, Electrical resistivity, strength at elevated temperatures, oxidation resistance, and bend transition. Of the 23 compositions tested, Cb-2OHf-5W-10Ti exhibited superior high-temperature properties. A recrystallized sample of this alloy was fabricable at room temperature, had a strength of 44,000 psi at 1,200° C, and had an oxidation rate of only 7.7 mg/cm2/hr at 1,000° C.

Jan 1, 1966

By Thomas Varley

[For a year or more, statements have appeared in the technical press, and Especially in various trade journals, indicating that valuable metals such as gold, silver, platinum, and other rare metals, have been found and also have been successfully extracted from oil shales. These reports stated tat decarbonization and special methods of chlorination treatment, leaching and subsequent Precipitation, also cyanidation followed by table concentration of the residues after cyanidation, all indicated that told ad silver and other metals could be, and were, successfully recovered. Such articles have caused much misunderstanding, and as the correctness of some re of the statements made in them were questioned by some of the technical journals and by various chemists and metallurgists, an investigation of the subject. was begun by the metallurgical division of the Bureau of Mines, in order, if possible, to determine to what extent, if any, metals of value do occur in oil shales, and if so, the feasibility of attempting their recovery by tie processes said to have been used for teat Purpose. Inasmuch as the Bureau's station at Salt Lake City is investigating the recovery of oil from oil shales, the investigation of too recovery of metals from oil shales was assigned to my direction as superintendent 'of that station. An agreement had been entered into with the owner of m extensive oil shale deposit in Wyoming whereby I would personally collect the samples' of shales for use in the investigation.]

Jan 1, 1922

By I. Iwasaki

In recent years the rapid depletion of high-grade iron ores and the demand by blast furnace operators for increasingly low-silica ores have stimulated interest in flotation studies of low-grade iron ores, such as wash-ore tailings and oxidized taconites. Four processes have been reported for the flotation separation of these iron ores--anionic and cationic collection of the iron oxides, cationic collection of siliceous gangue, and anionic collection of activated siliceous gangue (5).5/ The effectiveness of any one method, however, depends largely on the mineralogical composition and on the physical structure of the sample; hence, a comprehensive study of the floatability of the individual minerals occurring in these materials is essential. A review of the literature shows that the floatability of hematite and magnetite has been frequently investigated, whereas very little corresponding information is available for goethite, or for its more earthy form, limonite, both of which are abundant in the Mesabi and Cuyuna ores (19). The purpose of this investigation was to formulate general information on the floatability of goethite. Vacuum flotation, contact angle measurement, and simplified flotation tests using a modified Hallimond tube were used. The experimental results were correlated with the electrokinetic properties of goethite as determined by streaming potential measurement. The results were used to interpret the batch flotation tests made on an artificial mixture of quartz and goethite.

Jan 1, 1960

By H. C. Fuller

Submerged combustion and inverse solubility methods were investigated as promising alternative means for crystallizing manganese sulfate from solutions produced by leaching manganese ores with either sulfuric acid or sulfur dioxide. Evaporation of water from typical manganese sulfate solutions by sub-merged combustion techniques enabled production of a slurry containing 32 to 39 pct MnSO4.H2O crystals suspended in a saturated solution of manganese sulfate. Such a slurry required further processing by thickening or filtration and drying to produce crystals of MnSO4.H2O. In a second approach, semicontinuous processing of manganese sulfate solu¬tions by thermal crystallization under pressure effected a recovery of 94.5 pct of the MnSO4.H2O as dry free-flowing crystals. Treatment of a solution containing about 100 grams manganese per liter at 189° C, produced a "barren" solution containing only 1.9 grams manganese per liter. Calculations made on comparable manganese sulfate solutions show that the heat requirement of the thermal crystallization method was about one-third to one-fourth that of the submerged combustion method.

Jan 1, 1966

As shown in Table 9, consumption has risen steadily for the period November through April, reaching its highest level since June of 1974. Imports remained at a relatively high level in spite of decreased imports from Zaire and Belgium-Luxembourg. Award prices for cobalt sold by the General Services Administration on June 17, 1976 ranged from $5.058 to $5.41211 per pound of contained cobalt. The high bid was about $1 per pound above the current market price set by the major sales agent in the U.S. for cobalt on April 15, 1976. COPPER: Eight domestic producers on July 1 hiked refined copper prices by 4¢ to 74¢ per pound for cathode and to 74.625¢ for electrolytic wirebar. New York Commodity Exchange (COMEX) June pricing of prompt contracted copper averaged 70.6¢, with daily quotes registering between 67¢ and 72.5¢ per pound. In June, London Metal Exchange (LME) cash wirebar prices averaged 70.3¢, trading between a low of 65.5¢ and a high of 73.6¢. End of the month copper stocks totaled 108,758 short tons for the COMEX and 539,350 metric tons for the LME.

Jan 1, 1976

By J. P. Coughlin

The U.S. Bureau of Mines has developed a monitoring system that acquires and analyzes data for use in determining the conditions that may precede mountain bumps in coal mines. Based on a UNIX workstation linked to an array of geophones in a working longwall operation, the system captures complete waveforms of microseismic events and simultaneously obtains continuous samples of the voltage levels of each geophone. Event rates and locations are calculated and displayed in real time on the UNIX workstation, which is situated in an underground instrumentation room. These results also are transmitted from the workstation to a display computer near the longwall face. The system runs continuously and has the capability to acquire, analyze, display, and archive microseismic (transient) data and single point data, such as closure and pressure changes, simultaneously.

Jan 1, 1993

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By Andrew B. Cecala

This U.S. Bureau of Mines report provides a detailed description of the Bureau-designed modified shearer clearer system. Engineering drawings are provided for all major components of this system. The modified shearer clearer system is a revised version of the original system and is intended to improve the ventilation around both cutting drums. The original shearer clearer technique was solely a dust control technique that has been effective in lowering shearer operators' dust exposures. The technique uses a series of water sprays that not only knock down a portion of the dust cloud but also act as small fans that move a substantial amount of air and keep the dust cloud from dispersing over the shearer body. The modified version is composed of two additional spray blocks for improved air movement around both cutting drums, thus lowering methane levels and the likelihood of an ignition. A laboratory study performed with the modified version in a full-scale longwall gallery resulted in a 73-pet reduction in methane concentrations at the shearer machine for both cut directions. The air-moving capabilities of the system provide more turbulence at the cutting drums and reduce methane levels.

Jan 1, 1994

By D. Harrington

The coal-mining industry of the United States finds difficulty not only in making ends meet financially but also in operating with anything like reasonable safety. The record to date has not been particularly good as to either finance or safety, but at least in some phases or safety there are indications of better times to come. During the fiscal year ending June 30, 1929, only 139 lives were lost in explosions in our mines as against 342 lost during the fiscal year ended June 30, 1928; this decrease in such fatalities is definitely a matter for satisfaction. During the fiscal year July 1, 1928, to June 30, 1929, the attention of the safety division of the U. S. Bureau of Mines was directed to 38 mine explosions in the United States. Two explosions were in non-coal mines, one in a semianthracite mine, two in anthracite mines, and 33 in bituminous mines. These were not all major explosions - that is, explosions in which five or more lives were lost; in some of the explosions no lives were lost, while in others fewer than five fatalities resulted. Table 1 gives data on the explosions, showing the number of mines using open or closed lights and the number of explosions with resulting deaths, by causes, for each State.

Jan 1, 1929

By C. O. Anderson, W. M. Meyers

Since 1922, when a brief report3 on the production and utilization of garnet was issued by the Bureau of Mines, there have been a number of interest—in developments in the technology of that mineral. Greater activity has been displayed in mining, new mills have been erected, and more attention has been paid to improvements in milling so that a more efficient and economical recovery of garnet has been possible. These activities have resulted in larger production; therefore, attempts are being made to broaden the market for garnet abrasives, and to find new uses for the unusual combination of physical properties than this mineral possesses. The writers have recently completed a field study of the occurrence, methods of mining and milling of garnet, and the manufacture and utilization of abrasive garnet products. This preliminary report indicates the most important sources of garnet, the methods by which it is recovered, and the manner in which it is recovered, and the manner in which it is utilized.Chemical and Physical Properties.The term ""garnet"" is applied to a closely related group of minerals which crystallize in the caste forms and possess similar physical properties, although their chemical composition may exhibit greater variation. The chemical composition of the garnet group may be represented by the general formula 3R"" O.R""' 203.3S102, in which R represents the bivalent elements calcium, magnesium, in the manganese state and ferrous iron, R"" represents the trivalent elements, ferric iron, aluminum and chromium in the chromie state. An account of the amorphous substitution of the different bivalent and trivalent elements, specimens whose composition may be represented by a definite formula are rare, the composition of any given specimen generally exhibits treat complexity.

Jun 1, 1925

By Graham W. Marks

The general positions of the absorption maxima of aqueous solutions of the violet and green isomers of chromic sulfate the visible spectral region have long been known, but, to the knowledge of the writer, no comprehensive studies have ever been made. To gain further knowledge concerning these inorganic complexes and to investigate the possibilities of developing an analytical method for determining the concentrations of the violet and green isomers in a mixture, a more complete investigation was made in the spectral range from 325 to 850 millimicrons.

Jan 1, 1951

By Michael S. Miller

In 1986 and 1987, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied the nine separate parcels that comprise the 4,330-acre South Warner Contiguous Wilderness Study Area in order to evaluate their identified mineral resources. The nine parcels are along the east side of the South Warner Wilderness. They are, from north to south, the Granger, Milk, Cottonwood, Owl, Hornback, Eagle, Emerson, Barber, and Van Riper parcels. The Wilderness Study Area is underlain by basaltic, andesitic, and rhyolitic volcanic rocks and by sand and gravel deposits. Low-grade metamorphism is widespread in the volcanic rocks, with quartz, zeolites, datolite, chlorite, and calcite locally abundant in veins and amygdules. The rocks have been displaced by the mountain-front Surprise Valley fault and by crosscutting high-angle faults.

Jan 1, 1988

By J. B. Zadra

During the investigations of the occurrence of manganese in the western United States, the Bureau of Mines received a 100-pound sample of manganese ore from the Doyle-Smith property, Yuma County, Ariz. Laboratory tests were made to determine the amenability of this ore to standard ore-dressing methods of concentration to produce a marketable-grade product. The Doyle-Smith claims are in northern Yuma County, within 15 miles of the Artillery Peak deposit. The lot of ore used in the test work was taken from the outcrop of a large, massive, irregular bed of oxide manganese ore found on the claims.

Jan 1, 1952