Search Documents

By Robert E. Hershey

1. Estimates of reserves were made for three coal beds in Hamilton County the - Lantana, Sewanee, and Richland. Nine coal beds have been mined at one time or another in the county, but not enough information was available to estimate reserves in any beds other than the three given. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 short tons per acre-foot of coal in place, are estimated to be 53 million tons as of January 1, 1954. Of this total 35 million tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were insufficient for making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove re-serves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By Davis E. Traut

TiC14, AIC13, and VC14 were coreduced simultaneously via a Kroll-type magnesium reduction to form an alloy sponge as part of a research effort by the Bureau of Mines to produce titanium alloy powder. Reduction tem-peratures of 750°, 850°, and 950° C, a range of chloride feed rates from 34 to 152 Ib/(ft2·h), and crucible diameters of 7-3/4 and 10-1/4 in were tested. Microprobe analyses using a 40-um-diam spot showed no effect on alloy microhomogeneity (distribution of Al and V in the Ti, considered critical as a powder property), due to changes in process variables within these ranges. Statistical analysis of these data for alloy sponge indicated greater variation in the chemical composition (AI and V) than that found in commercial Ti-6Al-4V plate or Plasma Rotating Electrode Process (PREP) powder. Therefore, a one-step approach to pow-der, such as grinding the Ti alloy sponge, would not produce a powder product of acceptable chemical homogeneity. An approach that homoge-nized the sponge, such as with a melting step, would produce an accept-able powder product with respect to chemical homogeneity.

Jan 1, 1987

By G. B. Atkinson

The Bureau of Mines investigated a method for increasing the leaching rate of bulk superalloy scrap to facilitate recycling and recovery of critical metals such as Ni, Co, and Cr. Three superalloys were investi- gated, the cast-nickel-base superalloy IN-738, the wrought-nickel-base superalloy Rene-41, and the cast-cobalt-base superalloy Mar-M-509. Superalloys melted with 20, 30, 40, and 50 pct Al metal to form inter- metallic compounds were easily crushed to a convenient particle size and reacted rapidly with acid solutions which dissolved the metals. For example, leaching 1/2-in pieces of unalloyed IN-738 with excess 6N HC1 at 95° C for 2 h dissolved about 0.5 pct, while leaching 10 g of minus 20-mesh 30 pct Al-70 pct IN-738 with excess 6N HC1 at 95° C for 2 h dis- solved 96.2 pct.

Jan 1, 1983

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines presents compilations of inspection test data furnished on their products by manufacturers of commercial grades of aviation gasoline, and special data obtained in Bureau of Mines laboratories on samples of these gasolines. Data and physical samples for the survey were submitted by 15 manufacturers on 18 grade 80, 21 grade 91/98, 22 grade 100/130, and 10 grade 115/145 aviation fuels.

Jan 1, 1948

By Irving Hartmann, John Nagy

As part of a program designed to promote safety in industrial operations , the Bureau of Mines has been investigating the explosibility of numerous powdered products and dusts and studying means for the prevention of dust explosions . In a previous paper the results of a study of the inflammability and explosibility of metal powders were published . This report summarizes a similar study which has been made on various powders used in the plastics industry. The work was undertaken to provide information for a subcommittee of the Dust Explosion Hazards Committee of the National Fire Protection Association, which was charged with preparation of a code for the prevention of fires and dust explosions in plants producing or processing synthetic resins and molding compositions . The production of powders and generation of inflammable dusts are inherent in one or more steps of the manufacturing process of many resins and molding compositions, and control of the dust hazard is a major problem in the plastics industry . In the preparation of phenolic resin molding powders, for example , the solid synthetic resin is crushed and pulverized , and then blended with ground wood flour , cotton flock, or other fillers , as well as with coloring pigments . This raw mix is then passed through compounding mills , from which it emerges in the form of homogeneous sheeted stock, which is crushed , ground , and graded to form the molding powder . The number of major dust explosions in the plastics industry has been limited, but numerous small explosions have occurred, and in view of the ever -increasing volume of production the potential explosion hazard must be considered a very real one . Fortunately, this fact is realized by several manufacturers of plastic compounds , as well as by insurance companies , who are taking precautionary measures against possible accidents and during the past year or two have submitted numerous powder samples to the Bureau of Mines for explosibility tests .

May 1, 1944

By Thomas L. Starks

Surface soil/spoil Samples (0-10 cm) from experimental test sites in western North Dakota were aseptically collected during August 1975 and each month (May through September) during 1076 and 1977. Selected samples were Cultured in a defined inorganic medium and after six weeks the algae were identified. Chlorophyll u content of the soil/spoil was used as a measure of the algal abundance. Soil physical-chemical properties, species variety and abundance were statistically analyzed. All test sites revealed distinct soil algal communities and demonstrated a successional trend as evidenced by significant increase, in species variety and bionmass over time. Some soil factors, calcium, copper, and phosphorus affected species variety and abundance at more than one situ. Others were important at specific sites; silicon and aluminum at the South Beulah test site; manganese sodium and zinc at the North Beulah test site No. 1 and boron, cadmium and magnesium at the North Beulah test site No. 2. Topsoiled areas had higher species varieties and abundances when compared with control areas, as did plots treated with amendments such as leonardite and fertilizer Generally.

Jan 1, 1982

By Willard J. Tesch

The borehole surveying system described is used to measure ground movement over and near operating mines. The magnitude of any movement is con-trolled by the ground conditions, the mining method, and the mine progress. By correlating these factors with the measured movement, equations can be determined for predicting the effect of mine progress on the surrounding ground. These equations can also be used to predict the effect of mining a similar deposit with similar ground conditions. The borehole surveying system is used in cased boreholes to measure the inclination of the hole in two perpendicular planes. Grooved casing with an inside diameter of 3 inches is grouted in the hole. Two probes are used to obtain the data necessary to calculate the hole position versus depth. One of the probes contains a gyroscope, and the other contains a biaxial force-balance [s]ervoaccelerometer. Readings from the transducers in the probe are punched on paper tape by an automatic data acquisition system as the probe is pulled up the hole at 30 feet per minute by an electric winch. Readings from the inclinometer probe containing the accelerometer are used as input data to an on-line programmable calculator as they are punched on tape. The calculator computes preliminary results of the survey being made. The paper tapes obtained during the survey runs are later used as input to a computer that computes the offsets of the drill hole versus depth in true north-south and east-west planes. These offsets are printed for each foot of depth. Changes in these offsets between the first survey and subsequent surveys are a measure of the horizontal ground movement between the surveys.

Jan 1, 1976

By J. G. Walters

Analyses of light oils produced from the fluidized carbonization of coal at 485°, 550°, 600°, and 660° C are presented. Tar vapors from 485 C fluidized carbonization were thermally treated at 600°, 700°, and .800° C, and the analyses of light oils produced by this treatment are also presented. Procedures were developed for analysis of coal carbonization light oil by gas chromatography to permit a more definitive analysis than can be obtained by the conventional distillation procedure. An increase in low-boiling olefins, benzene, and toluene, a decrease in low-boiling paraffins, and little change in the remainder of the aromatics was observed with increased temperature of carbonization.

Jan 1, 1965

By Nadia C. Miller

In situ metals research to characterize the hydrology of a fractured crystalline rock mass in under-ground mine stopes is discussed. The objective of this study was to find the potential direction, velocity, and concentrations of a lixiviant plume, should leaching solvents (lixiviants) escape from a test stope. The study was conducted by the U.S. Bureau of Mines at the Colorado School of Mines Experimental Mine in Idaho Springs, CO. Since this was a method evaluation site, the lixiviant was simulated using water and acceptable tracers. The site is located in moderately fractured Precambrian migmatite-biotite gneisses of the Idaho Springs Formation. The data required for the characterization were obtained from geologic maps and reports, core logs, and air and water permeability tests. The acquired data were analyzed and applied to a computer model that calculated' the characteristics of a lixiviant plume originating at the stope. A sensitivity analysis showed that dispersivity, ground water velocity, fracture porosity, and fracture spacing had notable effects on the concentration of the plume. Assuming a saturated rock mass, the lixiviant plume would disperse to undetectable levels in a very short time because of a high fracture density at the mine site.

Jan 1, 2010

By B. K. Cantrell, K. L. Rubow

"Two source apportionment techniques have been applied by the U.S. Bureau of Mines to aerosol measurements in diesel-equipped underground noncoal mines. The first technique is based on size-selective sampling and the premise that the diesel exhaust fraction of the aerosol is predominately submicrometer in size while the mineral dust fraction of the aerosol is mostly supermicrometer in size. The second technique, chemical mass balance (CMB) modeling, was used to referee the analysis of diesel and mineral dust aerosol concentrations with the size selective method.The size-distribution data were modeled using a lognormal regression to parameterize the submicrometer and supermicrometer fractions of the sampled aerosol and to estimate the mineral and diesel contributions to each. Using this analysis, 97 ± 2 pct of the submicrometer aerosol mass was attributable to diesel exhaust aerosol.The CMB analysis, applied to both fractions of the respirable mi11e aerosol, yielded the amount contributed to each by the diesel and dust aerosol sources. On the basis of this analysis, 94± 10 pct of the submicrometer fraction was diesel exhaust aerosol. As much as 20 pct of the diesel aerosol, however, was found in the supermicrometer fraction, requiring a correction of the submicrometer fraction results to account for the missing diesel mass. More accurate measurements will require a carbon-specific analysis of the aerosol.INTRODUCTION Measurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and CMB modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample."

Mar 1, 1992

By Lloyd Williams

1. The investigation shows that the Pewee, Big Mary, and Windrock are the most important beds in Anderson County. About 73 percent of the known recoverable reserves of coal in the county are in these beds, and from them comes 94 percent of the production. The remaining reserves tabulated in this report are in the Joyner, Jellico, Coal Creek, and Poplar Creek beds, and 6 percent of the county production comes from these beds. No production is being reported at present from the Jellico bed, although it was mined years ago. 2. Known measured and indicated reserves in all beds, bared on a minimum thickness of 1/4 inches and on 1,800 short tons put acre-foot of coal in place, are estimated to be 170 million torts as of January 1, 1953 Of this total, 155 million tons is in beds 2S inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to permit making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to they total estimated reserves.

Jan 1, 1955

By S. L. May

Procedures for separating columbium and tantalum have been developed by the Bureau of Mines as part of a broad research program on the utilization of low-grade ores of columbium and tantalum, Columbium and tantalum compounds of greater than 99 percent purity have been obtained by application of the solvent extraction separation system: Hydrofluoric acid-sulfuric acid-methyl iso-butyl ketone. This system is unique in that it not only separates columbium from tantalum, but also separates these two metals from other metallic impurities. The system is effective for separating the metals irrespective of the tantalum and columbium ratio of the starting materials. Investigations in which the spent feed obtained from the initial coextraction step was recycled to the system indicated that efficiency was increased, and cost was reduced without impairing product purity. Continuous tests demonstrated that this solvent extraction system could be used in large-scale equipment without loss in efficiency or in purity of products. The separation of columbium and tantalum has been difficult because of the similarity in their chemical bahavior. Many methods have been proposed for separating these two elements, but most methods either did not achieve satisfactory separation or were tedious and time consuming. The Marignac process (3, 4)4 developed in 1866 was the only method used commercially until recently. This separation procedure is based on the difference in solubility in aqueous solution of potassium tantalum fluoride and potassium columbium oxyfluoride. Current commercial practice appears to favor solvent extraction as a method for separating tantalum from columbium (1). Several efficient methods for separating columbium from tantalum by solvent extraction (2, 9, 8) were reported earlier from this laboratory.

Jan 1, 1961

By Robert Hall

The Lynch Creek beryllium-tungsten prospect was investigated as part of the domestic beryllium resource studies by the Bureau of Mines. This prospect is in the Birch Creek mining district, Lander County, Nev., 9 airline miles south of Austin. A tungsten mine was operated intermittently from 1952 to 1957. Beryl was identified in the pegmatite dikes in 1960, and the lode claims were relocated. No beryl has been produced. Rocks in the area are Paleozoic sediments2 cut by pegmatite and aplite dikes and quartz stringers. Beryl occurs in random pockets, as disseminations throughout the dikes, and in occasional pockets in the quartz stringers.

Jan 1, 1962

By J. V. Scalera

Because of U.S. dependency on imported critical metals, the Bureau of Mines has conducted research to evaluate the possible substitution of nitrided low-alloy steels for higher chromium-containing alloys. The corrosion data for nitrided steels are limited primarily to the Soviet literature. The objective of this study was to determine the corrosion properties of six commercially nitrided low-alloy steels in a 5-wt % NaCl solution at pH 4. Weight-loss tests indicated that, in deaerated test solutions, most of the nitrided steels were less corrosion resist-ant than nontreated steels. However, electrochemical tests indicated that under more oxidizing conditions, nitrided materials are converted to a passive state with a significantly reduced corrosion rate. Elec-trochemical tests performed in an aerated environment confirmed the passivity of the samples in an oxidizing environment.

Jan 1, 1984

By A. F. Robertson

"INTRODUCTION This report is supplemental to R.I. 4178 and deals with the work accomplished between June 15, 1945, and September 7, 1945, on the Mitchell-Hodge mine, Grady mine, Albea and York property, and Cuzzort property.ACKNOWLEDGMENTSIn its program or exploration of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by exploratory project as soon as practicable after its conclusion. The Mining Branch, Lowell B. Moon, chief, conducts preliminary examinations, performs the actual exploratory work, and prepares the final report. The Metallurigcal Branch, O. C. Ralston, chief, analyzes samples and performs benefication tests.Acknowledgment is due Mitchell H. Kline, chief, Raleigh Division, Mining Branch; Abraham L. Fox, acting chief, Raleigh Division, Metallurgical Branch; and Rowe McCrae, district engineers, U.S. Bureau of Mines, Gainesville,"

Jan 1, 1946

By L. O. Bacon, H. R. Joesting, J. H. Getz

"INTRODUCTION For a number of years manganiferous iron ore has been mined on a small scale at Boston Hill, in Grant County, N. Mex. Total production up to 1943 is estimated to be over 793,000 long tons, containing 8 to 35 percent manganese and 26 to 46 percent iron. 4/ During 1941 to 1943 production was estimated to be 206,000 long tons, containing about 13 percent manganese and 37 percent iron. During 1944 daily production was several hundred tons, mostly from a single open pit. Several moderately large deposits have been mined: and many smaller ones have been found.From February to April 1945 geophysical surveys were carried out on Boston Hill by the Division of Geophysical Exploration, in cooperation with District 5, Central Region, Bureau of Mines, to determine if hitherto undiscovered manganiferous iron deposits exist. Field work was interrupted for a total of about 1 month during this period by work on other projects in nearby areas. Previous to the geophysical surveys, a preliminary examination was made by H. R. Joesting to determine if geophysical methods could be utilized in exploring the area. 5/Field measurements were made by L. O. Bacon and J. H. Getz, project geo¬physicists of the Bureau of Mines, under the general supervision of H. R. Joesting. A grid survey of the area, to locate geophysical stations, was made by Paul Russell, Bureau of Mines engineer, who also collected specimens for laboratory tests. Most of the computations and the preliminary magnetic and resistivity maps were made by L. 0. Bacon."

Feb 1, 1948

By E. J. Gleim

An important phase in the Bureau of Mines investigation of electrical machines designed for operation in gassy coal mines is testing enclosures of electrical components for explosion-proof qualities. In brief, this testing consists of filling and surrounding the enclosure with an explosive atmosphere of methane and air and then igniting the atmosphere within the enclosure to determine (1) Whether the resulting explosion is confined without discharge of flame; (2) whether the enclosure walls are permanently distorted; and (3) whether excessive pressures are developed within the enclosure. Ordinarily, the pressures encountered in routine testing do not exceed 100 pounds per square inch gage. Hence, the designer of the machine does not have too much difficulty in taking corrective measures to prevent flame discharge and distortion of the enclosure. Occasionally, however, the explosion pressures greatly exceed 100 pounds. Then the goblet of the designer may not be solved so readily, From experience over the year 0, the testing personnel often can predict that certain construction will result in high. Pressures, but, only in a very general way, has it been possible to advise designers what modifications might be made to reduce the explosion pressures to normal values. For example, if high pressures were developed in a motor starter having a partition with an opening through it, some enlargement of the opening may appear to be the logical procedure, but it has not been- possible to give information concerning the exact amount the opening should be enlarged to prevent development of high pressures .

Jan 1, 1952

By R. W. Holliday

To determine the copper and nickel content of reported ore occurrences in the Chippewa mine near Rockmont, Douglas County, Wis., the Bureau of Mines reopened and sampled the old shaft and workings during the summer and fall of 1953. Occurrences of native copper near Rockmont and others near Gordon, also in Douglas County, Wis., are in lava flows, which extend from the Keweenaw Peninsula of Upper Michigan southwest across Wisconsin and into Minnesota. Sporadic attempts have been made to find additional economic copper deposits in these flows since profitable mines were developed in Upper Michigan nearly 100 years ago. The Rockmont and Gordon areas were explored extensively more than 50 years ago. More recently, from August 1944 to duly 1945, an occurrence near Gordon was investigated by the Bureau.2/

Jan 1, 1955

By O. M. Bishop

From October 1943 to March 1944, the Bureau of Mines conducted core drilling at the Victory fluorspar mine, Hardin County, Ill. to test the Fredonia limestone and the included sub-Rosiclare sandstone zone beneath the existing stopes. Twenty-one vertical holes were drilled to an average depth of 60 feet. Ore was penetrated in six holes. Since its discovery in 1927, the Victory mine has produced approximately 5 percent of the total fluorspar mined in the United states after that date. The ore discovered in the early mine development is now exhausted, except that contained in pillars drifting to the northeast has partly developed one substantial ore body, and company drilling has indicated another nearby. The increasing need for fluorite for war use in 1943 suggested the desirability of mining the pillars, provided it could be established that no ore beds existed below the stopes or in areas to which access would be obtained through the present workings. This work describes the work accomplished during the project and presents the data obtained.

Jan 1, 1948

By Charles B. Kenahan

Vanadium is subject to only light corrosion in phosphoric acid at temperatures up to 60° C. and has a moderate corrosion rate in this acid at 100° C. It is relatively corrosion resistant in sulfuric and hydrochloric acids up to 60° C, but corrodes rapidly at 100° C. It corrodes rapidly in dilute nitric acid at 35° C. Vanadium is almost inert in 10-percent solutions of formic, acetic, lactic, tartaric, and citric acids; in 9-percent oxalic acid it corrodes slowly up to 60° C. and rapidly at 100° C. Vanadium is resistant to corrosion in substitute ocean water, tapwater, and in 3-percent sodium chloride and 10-percent sodium hydroxide solutions. It is readily attacked, however, by 20-percent ferric chloride, 20-percent cupric chloride and 5-percent mercuric chloride solutions. Vanadium is protected by contact with magnesium, aluminum, and steel SAE 4130 in substitute ocean water, by magnesium and aluminum in 3-percent sodium chloride solution, and by magnesium in tapwater. Vanadium protects copper in substitute ocean water. When vanadium and stainless steel are coupled in sulfuric acid solutions, both metals are usually unaffected by contact, whereas the corrosion rate of titanium in sulfuric acid is greatly reduced by contact with vanadium.

Jan 1, 1962