Search Documents

By W. E. Anable

The Bureau of Mines studied the purification of commercially available yttrium by melting it in a 100-kw electron-beam furnace. Button-scale melts were made to determine the ultimate purification that could be attained by melting yttrium at 1,733° to 1,770° C at low pressure (0.05 to 0.1 micron) for 1 to 120 minutes. In addition, numerous melts were made to study the effect of doping yttrium with carbon, 17 selected metallic additions, and 3 compounds. Except for nickel and zirconium, the metallic impurities in yttrium were lowered significantly on extended treatment; silicon was lowered only slightly. The nonmetallic impurities} oxygen, nitrogen, and carbon, were not lowered except on short exposures. In isolated instances, the oxygen content was lowered from 5,860 ppm to about 5,000 ppm. In most instances the carbon con-tent was lowered from 545 to about 220 ppm in 20 minutes and then increased again. It was concluded that yttrium cannot be purified by direct heating or by the doping technique employed.

Jan 1, 1965

By C. E. Reistle

The tests reported in this paper were made in the East Texas field in the summer and fall of 1932 as a part of the Bureau of Mines study of the operation of flowing wells and reservoir performance; and to determine, if possible, the minimum reservoir pressure necessary to produce the wells in this field by natural flow through different sizes of flow strings. The minimum reservoir pressure that would be required to maintain natural flow through 2 1/2-inch tubing was determined experimentally for the existing energy conditions in the East Texas field. With the present available data, however, it 'is impossible to predict accurately or to determine by calculation the necessary energy requirements for maintaining the vertical flow of oil and gas mixtures under all conditions. Although some valuable data were obtained which seem to have application to the solution of problems involving vertical flow, this important research of the petroleum industry is so involved that more study of the complicating factors influencing the flow of oil-gas mixtures through vertical pipes is required. Versluys4 has presented a mathematical analysis of the vertical flow of oil and gas mixtures which covers the fundamental theories of the problem-although, as he points cut, there are factors, particularly friction, slippage, and solubility of the gas in the oil that must be mown or determined experimentally before the equations he has developed can be applied to actual

Jan 1, 1933

The coal-bearing strata of Oklahoma occur in the eastern part of the state over an area of 14,500 square miles, 20.7 percent of the state's total area. Commercially valuable deposits of bituminous coal cover about 8,000 square miles in seams ranging from ten inches to five feet thick. Estimated reserves in Oklahoma are 1.6 billion tons, representing 0.3 percent of U.S. coal reserves. The vast majority of coal mined in Oklahoma used in a single power plant within the state. Oklahoma gained primacy when its regulatory program was conditionally approved January 19, 1981. Authority for the state to administer the Abandoned Mine Land program was granted January21,1982. On April 30,1984, the Office of Surface Mining substituted direct federal enforcement of the inspection and enforcement portions of the Oklahoma program. This substituted enforcement was based upon a finding by OSM that Oklahoma had not operated the inspection and enforcement portions of its program effectively. As of January 1, 1986, Oklahoma inspection and enforcement authority was reinstated. Full program authority was granted to Oklahoma on January 14, 1986.

Jan 1, 1992

By M. M. Barr

Rapid expansion of the titanium-metal industry focused attention upon ilmenite as a possible substitute for the more expensive and less abundant rutile in producing titanium tetrachloride. Most of the rutile available for this use is imported. Preliminary studies were undertaken to determine the chlorination characteristics of high-titanium slags produced by electric-arc furnace smelting of alluvial Idaho ilmenite at the Federal Bureau of Mines Northwest Electrodevelopment Experiment Station, Albany, Oreg. Low silicon, calcium, and aluminum contents of the slags enhanced their potential value for chlorination.

Jan 1, 1958

By Candice Stevens

The Territory of Afars and Issas is to receive its independence from France on June 27, 1977. The Territory's economic income was based on entrepôt trade through the port of Djibouti and trans-shipment of goods on the Chemin de Fer Franco-Ethiopian (CFE) railroad. The Territorial budget was scheduled to in- crease from $32.6 million3 in 1976 to $36 million in 1977, despite severe shortfalls in 1976 stemming from inflation and a persistent balance-of-trade deficit. Subsidies from France continued to sustain the economy, and the French pledged to provide approximately $140 million in aid annually after independence. In 1976, financial agreements were concluded with a number of Arab oil-producing countries, including Saudi Arabia which granted $10 million toward development projects. The new Republic of Djibouti is scheduled to become the 49th member State of the Organization of African Unity (OAU) and the 21st member of the Arab League, and to receive aid from their financial institutions. The port of Djibouti and the CFE railroad constituted the Territory's main economic resources. Traffic at the port greatly

Jan 1, 1980

By Donald J. Ninteman

This Bureau of Mines publication is a literature study of the problem of spontaneous oxidation and combustion of sulfides in underground mines. It summarizes the present-day hazards, process mechanisms, and prevention and control techniques of this growing problem in underground mines. The iron sulfides generally have the greatest tendency to oxidize, particularly pyrrhotite. The presence of moisture and oxygen is essential for the oxidation reaction. Highly fractured sulfides, when found with timber or combustible refuse in slowly circulating air, pose the most serious fire hazard. Quenching with water is effective in quickly dealing with local hot spots, but ventilation at high flaw rates is the most effective and economical means for long-term prevention and control.

Jan 1, 1978

By E. J. Matson

"SUMMARYThe Bureau of Mines has been investigating deposits of critical and essential minerals in the United States since 1939. Projects were set up on only the most promising properties. A preliminary examination of the Rio Grande property was made by Bureau of Mines engineers in July 1942 and the property was examined again in July 1943.The Geophysical Branch of the Bureau undertook a Geophysical survey of the area in November 1943 and was intermittently active in the district until June 1946. The major portion of their work was done from June 191 to November 1945. Favorable areas for exploration were recommended by the Geophysical Branch of the Geological Survey, 3/ and all holes were drilled in them.Two projects were set up by the mining branch in an endeavor to find ore bodies on the strength of the geophysical information."

Sep 1, 1947

By Robert R. Stein

Occupational noise caused by the rock drills used in mining was investigated by the U.S. Bureau of Mines. Using a large reverberation chamber and an automated drill test fixture (ADTF), the sound power levels of mining drills were measured to determine if there are types of drills that are advantageous from a noise production standpoint. Test results show that while there are not large variations among types of drills, there are still some choices that could produce a positive effect on overall noise exposure. It is also shown that lower noise exposures are possible using larger drills because of higher production rates and better operator positioning.

Jan 1, 2010

By Avis W. Effinger

In conjunction with pilot steamflood tests in the Venango sands of Warren and Venango Counties, Pa., the Marx and Langenheim (4)3 calculations were adapted and programed for digital computer solution to predict test performance. The Monte Carlo technique was incorporated in the calculations to provide values of several variables which could not be adequately defined from available information. The computation methods are explained and the FORTRAN IV program listing is presented. Data and results of the prediction calculations for Venango oil sands are also shown.

Jan 1, 1969

By John R. Reynolds

This paper describes mining and milling methods of the American Smelting & Refining Co. at the Morning mine in the Mullan area of the Coeur d'Alene mining region in Idaho and is one of a series of Bureau of Mines reports dealing with methods and costs of mining throughout the United States. The Morning mine has been described previously in a Bureau of Mines report published in 1930,2/ and the milling methods and costs at the Morning concentrator were presented in a Bureau of Mines report published in 1932. 3/ These reports are supplemented by this publication, which presents data to show the effect of changing times and conditions on a typical medium-size mining operation during the latter part of its history, when costs were rising and production was from increasingly greater depths. The report contrasts two periods in the history of the mine-periods not too far separated in years but considerably different in economic conditions. During the first period (1939) costs of labor and materials were moderate, mining operations were just being transferred from the main shaft to deeper workings opened from the offset shaft, and the operation prospered. During the second period (12 years later) production costs had increased following the national trend in all industry, mining was from greater depths near the bottom of the ore body, and the operation was becoming unprofitable. Mining on the lower levels of the property ceased in 1953.

Jan 1, 1956

By G. L. Leumann

"INTRODUCTION AND SUMMARYThe Andover-Sulphur Hill iron mines in Sussex County, N. J., have a production record extending over 100 years. The last production recorded was about 1880. These mines produced high-grade ore of two types: Red ore (hematite) and blue on (magnetite). Some sulfides (lead, zinc, and copper) were found underlying the iron deposits. Data as to size and grade of these sulfide bodies are very sketch"",Howard J. Hewitt of Elizabeth, N. J., lessee of the Sulphur Hill mines from 1940-45, prospected for lead, zinc, and copper. .His only production was several hundred tons of low-grade iron ore, which was crushed and used as heavy aggregate to make concrete blocks for ship ballast.In October and November 1942 made a magnetic survey of this area and bored six-diamond-drill holes with the dual objective of prospecting for sulfides and testing for extensions of the iron-are deposits indicated by the magnetic survey. 2/ In 1944, an iron-mining company examined this property and diamond-drilled seven holes. Between December 1949 and March 1950, the Bureau of Mines in search of sulfide deposits, bored three additional diamond-drill holes. Two of these were on the Sulphur Hill tract and one on the adjoining Tar Hill tract."

Sep 1, 1952

By W. B. Berwald, T. W. Johnson

"The United States Bureau of Mines, in cooperation with the Natural Gas Department of the American Gas Association, has been studying actively for the past several years the flow of natural as through high-pressure pipe lines. 4 This report deals with that part of the study involving the design of pipe-line systems consisting of lines laid parallel to each other. The lines are referred to as the original line and the parallel line. The paralleling lire may or may not extend the entire length &f the original line; however, the parallel line is connected at its two ends to the original line.As a result of the large expansion of the natural-gas industry almost all markets within economic distance, from the developed as fields have at least one pipe line supplying them with natural gas. Small increases in the consumers' demand for natural-gas can be met usually by increasing operating pressures, but any marked increase in demand necessitates paralleling sections of the existing systems. It is believed that to a large extent future expansion in the natural—gas industry will consist of paralleling the present lines. The several formulas given in this report have been developed to aid in the design of such systems. Curves and tables were prepared from these formulas to simplify the calculations materially and to facilitate determination of the sizes of pine to be used in paralleling various diameter lines to give the most economical design. The formulas are presented without detailed derivations, as a complete report on the flow of natural gas through pipe lines is being prepared which will contain the derivations of these formulas. Examples included here show the detail of application of the several formulas to problems of design of parallel lines."

Jun 1, 1934

"Requests are frequently received by the Information Service of the Bureau of Mines for published information on the coals of different foreign countries, as compared with coals mined in the United States. The analyses of various coals from several countries on the Pacific, which were submitted to the Fuels Division for certain tests between the years 1913 and 1916, may be of interest, and are shown below: Results of Analyses of Various Coals from China, New Zealand, Japan and Australia."

Sep 1, 1925

By Bruce Cantrell, K. L. Rubow

"INTRODOCTIONMeasurement of the contribution of diesel exhaust to respirable aerosol in mine environments has become increasingly important because of current concerns over the occupational health effects resulting from exposure to diesel emissions. In response to this, the U.S. Bureau of Mines is developing and evaluating new sampling methods for measuring diesel aerosol in underground mines. Two such techniques are being studied by the Bureau, size selective sampling and Chemical Mass Balance (CMB) modeling. These techniques use measurable physical or chemical characteristics of a mine aerosol sample to infer the amount of diesel particulate material contained in the sample.Size selective sampling is being adapted for measurement of diesel aerosol by the Particle Technology Laboratory (PTL) of the University of Minnesota under sponsorship by the Bureau. 1 It is based on the premise that diesel and mineral dust aerosol can be physically separated by size and collected during sampling using inertial impaction. An independent effort by the National Institute for Occupational Safety and Health to develop a size selective sampling technique was also sponsored by the Bureau.The second technique, CMB modeling, is being developed by the Bureau as an alternative measurement technique to referee the results obtained using size selective sampling.3 It compares measured trace element ""finger prints"" of aerosol sources with similar profiles of mine aerosol samples. From these, the portions of the sample contributed by each source can be determined. Results of these investigations in underground coal mines have confirmed that diesel and coal dust aerosol are of different size and can be measured separately using size selective sampling techniques.A major difference in diesel usage among underground mines is the requirement for exhaust gas cooling systems in coal and gassy noncoal mines. Nongassy mines usually employ limited exhaust conditioning in the form of catalytic converters, which have limited effect on primary exhaust particulate. The cooling system in most general use in gassy mines is the water scrubber. This device has little effect on most of the gases but removes particulate material from the exhaust. 5 Because of this, exhaust aerosol characteristics in nongassy mines are expected to be different. To see if size selective sampling techniques can be used in such mines, the Bureau and the University of Minnesota conducted a second study in three metal and nonmetal mines, two nongassy and one rated as gassy."

Jan 1, 1990

The Mine Safety and Health Administration (MSHA) defines an independent contractor as “any person, partnership, corporation, subsidiary of a cor-poration, firm, association or other organization that contracts to perform services or construction at a mine.” Contractors that perform specific types of work are required to report the number of employees who work at coal mines and noncoal mines.

Sep 1, 2007

By R. P. Vinson, D. P. Tuchman

The personal dust monitor (PDM) is a sampling device developed for measuring the personal exposure to coal mine dust of mine workers. The device is based on proprietary technology known as the tapered element oscillating microbalance (TEOM) originally developed as a fixed- site environmental particulate mass monitor by Rupprecht and Patashnick Co., Inc., Albany, NY. Currently, the monitoring of exposure to coal mine dust relies on periodic samples taken by traditional coal mine dust sampling units that use a cyclone, filter, pump, and laboratory measurement of the filter mass. Better measurement of mine dust levels has been the goal of industry and labor for nearly two decades. PDM technology offers accurate, end-of-shift and near real time assessment of worker dust exposure. Laboratory and underground tests compared measurements taken by a prototype PDM-2 (a two-piece TEOM) to the average of multiple personal dust samplers monitoring the same space. In the range of mass loadings P between 0.5 and 4.0 mg/m the PDM met a 25% accuracy criterion 95% of the time with 95% confidence. However, some questions still exist about potential bias between types of coal. The prototype two-piece device is in the process of being combined into a single unit that also contains the miners' cap lamp creating a more ergonomic dust sampling system.

By Eugene T. Sheridan

The Bureau of Mines annually canvasses the fuel-briquet and packaged-fuel producers in the United States and publishes economic data on these industries, based upon reports submitted voluntarily by producers. This publication lists all producers that reported commercial production to the Bureau for 1960 and presents data on individual plants. The companies named herein represent virtually all producers of processed minerals fuels. A few small plants may not have been canvassed or failed to respond to the survey because some of the smaller plants operate intermittently and the survey is voluntary. All plants that reported commercial production were included; regardless of size. Specifically excluded were plants that manufactured briquets from wood charcoal. Fuel briquets and packaged fuel are manufactured solid fuels, produced by mixing fine-sized mineral fuels with binding materials and compressing into small individual shapes, Briquets are produced in pillow-shaped and cylindrical form, are 2 to 4 inches long, and weigh 2 to 4 ounces. Packaged fuel consists of 3- or 4-inch cubes; 6 or 8 of which are wrapped together in heavy kraft paper to form a package weighing 10 to 15 pounds, Briquets are durable and may be stored and handled as bulk fuel; packaged fuel breaks easily and must be stored indoors to prevent it from deteriorating. Whereas briquets are consumed in many areas as a general residential fuel, packaged fuel is more of a specialty item, used at times to supplement other fuels. Packaged fuel is burned without re-moving the paper and is referred to as the "white glove" fuel.

Jan 1, 1961

By W. D. Mcmillan

"Magnetic surveys made by the Missouri Bureau of Geology and Mines in 931 and 1932 disclosed a large positive anomaly about a mile south of Bourbon, Mo. 3/ Electrical resistivity measurements made by the Division of Geophysical Exploration of the Bureau of Mines in the winter of 1942-43 indicated that the source of this anomaly was in the pre-Cambrian rhyolite at a depth of more than 1,400 feet. 4/In order to determine the character of the material that caused the magnetic anomaly, which might be either a body of magnetite or a large intrusive of basic rock, the Bureau of Mines drilled four holes to depths of 1,800 to 2,300 feet. Magnetite in rhyolite porphyry was encountered at 1,600 to 2,000 feet, and this is doubtless the main source of the magnetic anomaly, although it is possible that additional iron ore exists at greater depth.Hole 1 was apparently located southeast of the source of the anomaly and encountered only small stringers of magnetite. Hole 2 penetrated four mineralized zones having a total thickness of 125.7 feet and an average weighted content of 43.52 percent iron and 31.62 percent silica. These zones were tested again by a deflection hole, 2A, which gave nearly identical indications. Hole 3, 500 feet north of hole 2, penetrated 58 foot of mineralized rhyolito containing an average 43.4 percent iron.Metallurgical tests showed that the silica in the ore is tightly locked with the magnetite. After grinding to minus 100 mesh, a 66 percent iron con¬centrate with 7 percent silica was obtained by flotation."

Oct 1, 1946

By William R. Barton

COLUMBIUM (niobium) and tantalum are similar refractory metals with closely related properties and uses and close association in ore deposits. Until recently both metals, particularly columbium, were essentially laboratory curiosities. However, since the beginning of World War II, applied technology, under the impetus of national security requirements, has realized many chemical, electronic, nucleonic, and missile and rocketry applications, where high temperature or corrosive environments require the use of columbium or tantalum. At the same time, advances in these fields have resulted in intensive research on the geological distribution, resources, metallurgy, and properties of these two metals; their alloys and compounds; and the development of a full-fledged columbium-tantalum industry. The future appears to promise continued acceleration in such studies and ever-increasing demand for these elements. The raw material supplies of columbium are abundant, and the extractive metallurgy of columbium is well enough advanced to assure adequate supplies of the element at reasonable prices to meet any projected demands. Although the extractive metallurgy of tantalum is similarly well developed, raw material supplies are so limited that, lacking new ore discoveries, an increase in demand to five times the 1959 level would severely tax ore-production facilities. Approximately 120 tons of tantalum and about one-half as much columbium was produced in 1959. Additional quantities are consumed as compounds or additive alloys such as ferrocolumbium and ferrotantalum columbium (55).3

Jan 1, 1962

By Robert I. Fujimoto

The work described was conducted to develop standards for the application of wire rope clips on wire rope. These standards include optimum number of clips and clip nut torques for wire rope sizes 1/4 through 2-1/4 inches, when used for forming an eye attachment in wire rope. Wire rope test specimens with clip attachments were load tested on tensile testing machines to determine an effective combination of clip nut torques and number of clips for each size of wire rope to develop efficiencies above 90 percent of the catalog ultimate rope strength.

Jan 1, 1973