Search Documents

By Mukund O. Gangal

A deep cutting continuous miner, HH456, was tested under production-mining conditions at the Joanne Mine, Rachel W. Va., for about 1 ½ years (226 production days). The miner was run in two modes: a low head-rpm, deep cutting and high rpm, shallow-cutting mode. These tests confirmed that deep cutting and slow cutter speed reduce respirable dust significantly under production mining conditions. Quantitative reductions in dust, in deep vs shallow cutting, were 73°; in return air and 63% at the operator's location. Production rate, (tons/shift), and bit consumption rate did not show any relationship to deep or shallow cutting. Reliability and maintainability of the miner were worse in deep cutting mode due to cutter drive shaft failures; the cutter shaft problem was solved through improved material and design. Excluding the cutter shaft repairs. maintainability war similar for deep and shallow cutting,

Jan 1, 1979

By Piyush K. Dutta

This report describes the design, development and manufacture of a prototype quiet hard rock stoper drill and results of its field tests. It is shown that the stoper drill noise level can be reduced from 118 dBA to below 100 dBA by using this design. The design concept of this drill is based on a valveless independent rotation system, use of an integral muffler and pivot mount. The drill was manufactured in a standard commercial drill manufacturing setup and organization. The design and production technology proved that commercially viable quiet drills can be made available for mine use.

Jan 1, 1985

By Bruce McDonald

This report contains the findings of a study to perform a task and skill analysis of roof-bolting operations, with respect to the operational training requirements and to prepare detailed recommendations for the operational training system. The extent of the problem was determined by visiting underground coal mines, interviewing training and safety personnel, observing and interviewing roof-bolter operators, and reviewing present training programs and facilities. In conjunction with the mine visits an extensive literature search was conducted with emphasis on training, mine safety, and accidents involving the roof-bolting operation and roof-bolter operators. A number of training programs and training devices were considered resulting in the development of a recommended training program including training devices to be used and establishing training objectives.

Jan 1, 1977

By Mildred Nadler, Alvin Kaufman

To aid industry and Government in planning water developments the Bureau of Mines in 1963 canvassed mineral producers to determine water use in 1962. Water use by the mineral industry comprises only 2 percent of the water withdrawn by industry as a whole. The major water-using mineral industries are natural gas processing, phosphate rock, sand and gravel, and iron ore. Analysis indicated the following conclusions: 1. Total water use and new water intake is dependent on the quantity of material processed and the process water requirements of the particular indus- try or commodity. 2. Recirculation is dependent on the processing requirements of a par- ticular commodity, the manner in which the water is used, cooling and condens- ing requirements in certain large industries, the quality of new water intake, and the need to treat new and discharged water. 3. Consumed water is dependent on the quantity of water recirculated, the temperature and humidity in the area, and the proportion of water used for cooling and condensing. 4. A threefold increase in water use by the mineral industry by 1985 is forecast.

May 1, 1965

By Robert C. Weisner

Current production costs and market conditions in the potash industry of the Carlsbad area were studied to determine the potential values of the potash mineral resource that would be lost or foregone if the Waste Isolation Pilot Plant (WIPP) facility is constructed on the proposed site in that area. The purpose of the WIPP project is to investigate the possibility of developing a nuclear waste disposal plant in the salt formations at the site. Analyses were made of all potash deposits determined to be in the site. Mining and processing under the most favorable recovery systems were considered. Value determinations were based upon estimated operating and capital costs of current mine-mill operations in the Carlsbad area. This study was made for the Energy Research and Development Administration (ERDA) by members of the Federal Bureau of Mines Minerals Availability System staff.

Jan 1, 1979

By Harry R. Nicholls

As part of the pre- and post - shot mine examination at Project GNOME , acceleration data were recorded underground from a series of chemical explosive shots . The cube root of the charge weight was used to scale acceleration and distance because charge weight was not constant . Regression analysis of particle acceleration - distance data gave the following propagation equation : A W1 /3 = 5.10 x 105 ( R / W¹ / 3 ) −2 .43 The quantity A W1 /3 is scaled particle acceleration expressed in g's - lbs¹ / 3 , and R/W1 /3 is scaled distance expressed in ft / lbs¹ /3 Data obtained from the nuclear explosion were scaled and fall within one standard deviation of the calculated propagation law for the smaller shots . Cube root scaling laws were adequate to group acceleration data from explosive charges varying by a factor of more than 1 x 10 in charge weight and over shot - to - gage distances varying from 100 to 46,000 feet . Data obtained from a series of small tests provided sufficient data from which reliable predictions of acceleration could be made for the large nuclear explosion .

Jan 1, 1964

By D. F. Hambley

This manual contains a step-by-step procedure for the design of ore passes for open pit mines. The manual is comprehensive and deals with all aspects including location, design, construction and operating considerations. In the construction section, all applicable raising and shaft sinking methods are considered and cost estimates and advance rates provided for each. The design process is divided into several sections - rock flow requirements, support design, dump point design and draw point design. Use of this manual provides open pit planning engineers with a means of designing and assessing the feasibility of ore passes for their operations.

Jan 1, 1983

By Zsuzsanna Zborovszky

A circuit is considered intrinsically safe when any spark or thermal effect produced normally (that is, by operating the equipment in its correct operational manner to fulfill its purpose) or accidentally (caused by short circuit, earth fault, defective components, breaking the wiring, etc.) is incapable under prescribed test conditions of causing ignition of a prescribed gas mixture. The test conditions and gas mixture should be at least as hazardous as the true parameters of the environment where the circuit will be operated. According to present practices, the question of whether or not a circuit is intrinsically safe is decided upon experimentally. The circuit is inspected first for mechanical soundness and a survey is made to determine what faults should be considered as probable. Then the individual branches are connected, in sequence, to a test apparatus called 'breakflash" which acts as an opening, closing contact and thus draws sparks from the circuit. This test is repeated a given number of times in the presence of the prescribed gas mixture under specified conditions (electrode configurations, gas parameters, etc.). The equipment will be regarded as intrinsically safe if during testing no ignition has occurred.

Jan 1, 1972

By G. St. J. Perrott, G. W. Jones

"In cooperation with The Edison Electric Illuminating Co. of Boston, Mass., a survey was conducted in 1929 and 1930 by the United States Bureau of Mines to determine the general hazards of combustible gases and vapors in manholes and other underground openings owned by this company. The territory served approximates 650 square miles and includes 46 cities and towns. The transmission and distribution systems are on overhead construction and underground wires and cables run in underground conduits and manholes. There are 17,000 manholes on the system, and also an area in Boston proper served by the Edison tube system. These conduits and manholes are laid in various types of streets from the most modern type of cement roadbed to the older type of loose macadam. The conditions as found could be considered as typical of any public utility in the electric-light and power field. The survey extended over a period of about a year beginning in June, 1929, and ending in July, 1930, and during this time 1,765 different manholes were tested and a total of 4,068 tests were made.Previous to starting the actual survey, one of the writers, G. W. Jones, spent considerable time in Boston determining the best methods of practical· test procedure. In this work cooperation was given by John Campbell, superintendent, special service department, who for a number of years has been making a study of explosions in underground street areas and preventive measures in Boston and various cities.After this preliminary investigation the tests were continued by employees of the Edisun Company. Copies of all records of tests were forwarded to the United States Bureau of Mines Pittsburgh Experiment Station so that the writers were in close touch with the progress of the survey, and changes could be made in the test procedure whenever deemed necessary."

May 1, 1931

By J. Frederick Stampfer

Current certification testing of self-contained breathing apparatus includes tests with human subjects wearing the apparatus while exercising. During these tests, certain apparatus variables are measured during rest periods. Because of concerns that the present tests may not accurately simulate the stresses to which an apparatus is subjected in the field, the Bureau of Mines proposed new human subject tests. It was also felt that different measurement techniques would supply more reliable data on the apparatus response to these stresses. The Los Alamos National Laboratory was asked by the Bureau to evaluate the proposed tests and monitoring techniques. The major conclusions derived during this study are these: (1) The proposed tests are not too physically demanding. (2) As long as human test subjects are used, a minimum subject weight should be required for certification tests. (3) Important apparatus variables are the breathing resistance, temperature, and carbon dioxide and oxygen concentrations of the inhaled gas. (4) Continuous monitoring should be used, rather than monitoring only during rest periods. (5) New pass/fail criteria based on realistic estimates of the user's physiological requirements, as tempered by present and future engineering limitations, are needed. (6) When available, breathing machines, rather than human subjects, should be used for most certification testing. (7) A more realistic ergonomics test than that proposed is needed. (8) A gas leak test for the system and a facepiece leakage test are also needed.

Jan 1, 1983

By James Westfield

This publication covers the work of the Division of Coal Mine Inspection, Bureau of Mines, as performed under provisions of the Federal Coal Mine Safety Act. It presents background information and data since 1952 when the Act became effective and includes up-to-date statistics for the calendar year 1962. During that year, approximately 9,704 coal mines were active in the United States, and the Bureau made 12,810 regular inspections. BACKGROUND The Federal coal-mine inspection program was established to carry out the provisions in Public Law 49, 77th Congress, (H. R. 2082) approved May 7, 1941. This act has since been amended as Title I, Advisory Powers Relating to Health and Safety Conditions in Mines, under Public Law 552, 82d Congress, approved July 16, 1952, which also included Title II, Prevention of Major Disasters in Mines. Public Law 552 is known as the Federal Coal Mine Safety Act.

Jan 1, 1963

By C. Steve Albrecht

The primary objective of this study is to "evaluate the influences of different equipment systems on prime farmland subsoil compaction due to surface mining in the Midwest." The study is centered on four mine sites each utilizing a different combination of equipment for soil removal and replacement. Subsoil compaction is the primary focus of this research effort. Primarily owing to physical location, it is difficult to alleviate the increased compaction directly below the topsoil in reclaimed soils. Different equipment combinations cause varied effects when soils are replaced during surface mining activities. By collecting field data within a statistical framework, the effects of different equipment combinations on subsoil compaction can be evaluated and conclusions drawn. This research effort evaluates a comparison of natural and replaced soils by moist bulk density data. This comparison centers on changes in bulk density and texture to a depth of 48 inches. For each study site a complete case study is provided for use in data correlation and interpretation. Basis for this research effort centers on four (4) major experiment designs: o Comparison of soil bulk density values for three distinct equipment systems evaluated on the same general soil types (i.e. scrapers, bucket-wheel excavators and end-dump haulback); o Evaluation of the effects of soil replacement in repeated lifts using scrapers; o Presentation of bulk density values representing soil compaction for four (4) equipment systems (i.e. bucket-wheel excavators, draglines, scrapers and end-dump haul back) on four separate mine sites in the midwest; o A prediction analysis model is developed for subsoil bulk density following reclamation based on equipment characteristics and a statistical evaluation of texture. The soil data base of information includes data from the 1982 Bureau of Mines study entitled, "Impact of Surface Mining on Soil Compaction in the Midwest" as well as data from this research project. The final report is synthesized through an analysis of field data, statistical analysis and literature review. The final report focuses on the interpretation of results for practical application by government and industry.

Jan 1, 1984

By J. P. BONARDI, J. C. Williams

Until the end of 1918 Boulder County ranked as one of the foremost tungsten-producing districts of the world, but in August, 1919, there was practically no production in the district. The operators there could not compete with tungsten ores from foreign sources, particularly China, Burma, and South America. As a. result there · has been a strong movement for placing a protective tariff on all imported tungsten ores and products; and it seems to be the general belief of tungsten producers that some form of protection is necessary to the maintenance of the industry in this country. The stimulus, due to the great demand for · tungsten alloys in the manufacture of munitions during the war, was felt in all the productive localities of the world. The ores of Boulder County were especially in demand on account of their comparative. freedom from • harmful impurities, and this demand greatly extended mining operations in the district and increased the efficiency of the gen~ral milling practice there.

Jan 1, 1921

By C. E. Henning

The total number of petroleum refineries in the United States on January 1, 1958, was 318 and their total crude-oil throughput capacity was 9,407,707 barrels per day, according to the Bureau of Mines annual survey. During 1957, 3 new refineries began operating while 4 refineries were retired. Although there was 1 less refinery, the total crude-oil throughput capacity at the beginning of 1958 was 284,033 barrels per day, or 3 percent, more than the January 1, 1957, level. During 1957 all refinery districts showed increases in capacity. The largest increase, 27 percent, occurred in the West Coast district followed by the Indiana-Illinois-Kentucky district with 14-percent increase and the Texas Gulf Coast district with 13-percent increase. The national increase in capacity had the effect of raising the capacity of the average refinery from 28,601 to 29,584 barrels per day. New crude-oil capacity under construction on January 1, 1958, totaled 185,265 barrels, and an additional 297,885 barrels capacity was reported building as replacement for existing facilities. Included in total new construction were 2 new refineries, 1 in Washington and another in Texas, with planned processing capacities of 45,000 barrels and 8,550 barrels per day, respectively.

Jan 1, 1958

Minerals are vital to any industrialized civilization. Annually, the United States uses more than 4 billion tons of new mineral materials, or about 40,000 pounds per person-about half being mineral fuels and the other half being metals and nonmetallics. Stable and economic domestic mining, mineral, metal, and mineral reclamation industries are essential to the economy. The value of United States energy and processed materials of mineral origin exceeds $200 billion annually. Although a number of minerals are imported, especially some designated as "strategic and critical," most U.S. mineral supplies are derived from the domestic mines and processing facilities that you will be seeing, reading about, and visiting as you use this visitor guide. We hope you enjoy your experiences. This pamphlet, a guide to mining and mineral operations that may be observed or visited and some other points of interest relating to minerals, is intended to aid tourists and students who are interested in mining. Some may wish to study our Nation's romantic past; others may plan to enter the minerals industry as a career; still others may have a primary interest in conservation practices. The pamphlet is also intended to aid State and local officials, Chambers of Commerce, and mining firms in answering some of the many questions of tourists and students.

Jan 1, 1977

By G. R. Hopkins

According to reports received by the Bureau of Mines, Department of Commerce, as of January 1, 1929 there were 413 completed refineries in the United States, with a total daily crude-oil capacity of 3,509,540 barrels. In addition, 14 refineries, with a potential capacity of 99,000 barrels, were being constructed. Of the completed refineries, 341, with a capacity of 3,325,890 barrels, or 95 per cent of the total capacity, were in operation; and 72, with a capacity of 183,650 barrels, or 5 per cent of the total, were shut down. The improved condition of the refining industry in 1928 was indicated in several ways; namely, in an increase in the total capacity of the completed plants, in the opening up of a few plants which were shut down during 1927, in a decrease in the number of plants dismantled, and in an increase in the number of plants under construction. The majority of the refiners have followed a steady expansion program commensurate in most cases with the increase in demand for petroleum products. Obsolete equipment has been dismantled and modern equipment has been installed, with the net result that the total capacity of the completed refineries in the United States has shown a steady increase since January 1, 1918, the date of the first Bureau of Mines survey. Between January 1, 1928, and January 1, 1929, the number of completed plants fell from 423 to 413, but their total capacity increase 259,160 barrels, or 8 per cent. This compares with an increase in runs to stills of domestic and foreign crude petroleum of 10 per cent, and of domestic crude alone of 7 per cent.

Jan 1, 1929

By V. L. Burdick

A literature review of current uses of Mn02 in ceramic applications with suggestions for future research. Historical background, oceanographic distribution, geology, exploitation, law and politics. Uses of Mn02 in ferrites, semiconductors, catalytic processes, thermo-luminescence and photochromic materials. Select bibliography of 33 items, plus 129 references.

Jan 1, 1980

By John J. Baz-Dresch

Catalyzed diesel particulate filters (CDPF's) reduce the concentration of diesel particulate matter (DPM) and may reduce the emissions of carbon monoxide (CO) and hydrocarbons (HC) in diesel exhaust. Asamera Minerals' Cannon Mine first installed CDPF's in 1987, and currently has 12 diesel-powered vehicles equipped with CDPF's. The Cannon Mine and the U.S. Bureau of Mines collaborated to evaluate the durability and performance of a CDPF. One of the CDPF's used at the mine was periodically evaluated in the USBM's diesel emissions laboratory after 839, 1,584, and 2,881 h of in-mine service. The objectives of this report are to present results from the USBM's evaluation of this CDPF, to describe the Cannon Mine's experience and cost analysis of using CDPF's, and to make recommendations for the future use of CDPF's. CDPF's improve air quality at the Cannon Mine, but they frequently become plugged and are subject to excessive mechanical shocks and stress, shortening their useful life. Mine records indicate that CDPF's account for 0.8 to 4.9 pct of the vehicles' operating cost at the lVine. CDPF life to date has ranged from 1,671 h to more than 5,992 h. Laboratory tests of the CDPF determined that DPM removal efficiency decreased and regeneration temperature increased over time.

Jan 1, 2010

By S. H. Lorain

This paper, which describes lode gold mining in Idaho county, Idaho, is one of a series on western mining districts being published by the Bureau of Mines. It describes mining and milling practices, gives costs, and discusses transportation, climate, power, labor, and other conditions that affect them. The materiel upon which the paper was based was gathered during a field survey in the summer of 1937.

Jan 1, 1938

By Ronald S. Conti

This U.S. Bureau of Mines (USBM) report describes various fire-fighting resources available to the mining industry and examines the fire preparedness of four western coal mines. Information regarding fire-fighting equipment indicates that an inadequate maintenance program may cause component failure of fire extinguishers, damage to waterhoses is usually a result of improper care, and foam may be a convenient means of conveying water to the fire. Performance data relative to water nozzles (throw distance) and specific practices to improve the state of preparedness in many of these areas are discussed. Studies also indicated that a high-expansion foam plug, will travel down an entry, with a 1% rise in elevation, 207 m (680 ft) before a plywood stopping separating the generator and plug failed. The advance rate of the foam plug decreased when the entry is dry, requiring more foam concentrate and as the foam spread further down the entry. An examination of the mines showed state-of-the-art monitoring systems were common at the minesites. Fire safety was also stressed, including early detection and rapid response of the miners to evacuate the mine. However, the mines placed little emphasis on performance of water nozzles, or personal protective clothing for the underground firefighters.

Jan 1, 1994