Search Documents

By Edward D. Thimons

As U.S. mines go to greater depths, the high temperatures and humidities characteristic of such depths make it difficult to maintain a comfortable environment in working areas. Better techniques for cooling these deep working areas are needed. At the Homestake gold mine in South Dakota the Bureau of Mines has tested a water spray cooler inserted into the fresh air vent tube entering a warm stope. The cooler supplied more than 6 tons of refrigeration to the stope air, which dropped from an inlet temperature of 83° F dry bulb and 75° F wet bulb to 73.5° F dry bulb and 71.5° F wet bulb. These preliminary results show the water spray cooler to be a feasible concept. However, there is a need for substantial refinement and further testing, and work on the concept will be continued under contract to the Bureau.

Jan 1, 1979

By W. R. Hardwick

This paper describes mining methods and practices of the Morenci Branch, Phelps Dodge Corp., Greenlee County, Ariz. It is one of a series being prepared by the Bureau of Mines on mining methods, practices, and costs in various mining districts in the United States. A similar program, conducted from 1928 to 1939, was generally conceded to have contributed substantially to improving the efficiency of mining operations. The morenci open-pit mine (see photograph, fig. 1) is in southeastern [zona] (fig. 2), on U.S. Highway 666 about 5 miles north of Clifton, county at of Greenlee County. The concentrator and smelter are near the mine at an altitude of about 4,400 feet. Figure 3 is a map of the mine and plant.

Jan 1, 1959

By R. G. Bottge

To better understand those factors which increase mining costs in Alaska, a Bureau of Mines study was conducted to compare the estimated costs of operating a 100,000-tpd open pit copper mine located on a hypothetical ore body in the Lake Clark area, Alaska, with the costs of mining a similarly sized hypothetical copper ore body near Tucson, Ariz. The information derived should be beneficial to the State and Federal governments in appraising the potential for development of large, low-grade porphyry copper deposits in south-central Alaska. Conventional mining and concentrating methods were assumed, and capital and operating costs were derived using flowsheets and standard costing methods. The total price required for copper mined in Alaska and Arizona was $1.12 and $0.63 per pound, respectively, plus or minus 20 percent. These values were obtained assuming no leaching of low-grade copper, recovery of gold, silver, and molybdenum as byproducts, 100-percent equity financing, and a 12 percent discounted cash flow rate of return. The average domestic and international prices for copper in July 1973 were $0.60 and $0.916 per pound, respectively. The existence of a developed transportation and power system in Alaska would have reduced capital and operating costs subs tantially. The required price for copper would have declined from $1.12 to $1.05 per pound, plus or minus 20 percent.

Jan 1, 1974

By A. G. Galaitsis

The two volumes of this report summarize the noise control work performed by BBN on a rail personnel carrier operated in coal mines. Volume I of the report - submitted November 1977 - describes the aboveground work performed to identify the noise sources, design, fabricate, and install the treatments, and evaluate the treatments through noise and vibration tests. The current volume (II)-describes the underground work conducted by BBN to determine the deterioration, if any, of the treatments when the vehicle is operated normally in a mine. There were no significant changes in the acoustical performance or mechanical integrity of the treatments at the end of a three-month period.

Jan 1, 1980

By Edward E. Johnson

The Bureau of 'Mines publishes in its ?Minerals Yearbook? a series of indexes on the domestic minerals industry. Among these are the index of physical volume of mineral production, indexes of stocks, and indexes of average unit mine value and implicit unit value, This report describes the material coverage of these indexes and the methods used in their construction. Detailed descriptions are given for several other mineral-oriented indexes regularly published by other government agencies. These descriptions give the index user a better understanding of what each index purports to measure and aids him in selecting the most appropriate index for his purpose.

Jan 1, 1965

By W. H. Tomlinson

One of the more important functions of the Federal Bureau of Mines is conservation of the life and health of employees of the mineral and allied industries. Since its very beginning the Bureau has encouraged competition between mine rescue and first-aid teams as a means of stimulating interest in safety and accident-prevention work. In addition to sponsoring competition on a national and international scale during the past 45 years, the Bureau has also assisted State mining departments, mining companies, and mining organizations in holding State, district, company, and other local meets. This assistance includes providing instructors to train teams, judges, and other contest officials. The Bureau has also furnished problems and outlines for working them, judges I discount sheets (scorecards), contest rules, and problem judges. In fact, Bureau representatives participate in nearly all State, district, and company contests and have bad complete charge of some contests.

Jan 1, 1956

By J. E. Tiffany, N. A. Tolch

The Pittsburgh Experiment Station has made a survey of the properties and characteristics of the brands of fuse manufactured in the United States ; 25 samples were procured from 4 manufacturers representing the different brands offered on the market when the investigation was begun . It is believed that the field was completely covered except for special fuse made to order for a particular job .

Jun 1, 1934

By W. T. Abel

Laboratory tests were conducted with a closed, recycling system to evaluate the effectiveness of solid-in-gas suspensions as heat transport mediums. Micronized graphite in helium or nitrogen was circulated by a centrifugal compressor to determine the feasibility of the method and heat transfer capabilities of the mediums. Suspensions were circulated without plugging or eroding the compressor or piping. At low flowrates and light (0.1 to 0.2 volume-percent) graphite loadings, slightly less power was required to transport a given amount of heat with suspensions than with helium alone. Graphite deposition on the heat exchange surfaces of the cooler decreased the heat transfer effectiveness at higher solids concentration. Efforts to eliminate deposition are described.

Jan 1, 1963

By T. W. Quayle

This paper describing mining practices at the United Verde copper mine, Jerome, Ariz., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts f the United States. At present mining operations are being conducted both underground and by electric shovels in an open pit. The open-pit work has been described by E. M. J. Alenius in a previous publication of the Bureau of Minos;3 the present paper will be confined to a description of the underground mine. The underground methods comprise horizontal cut-and-fill, shrinkage with delayed filling, horizontal square-set, inclined square-set, and top slice. The normal daily production of the underground mine is 3,000 tons of copper ore per day, requiring the employment of 900 men underground.

Jan 1, 1931

By R. Lusignea

This report describes the development of a device for the nondestructive testing of resin grouted roof bolts by means of mechanical frequency response. Various alternative methods were evaluated and the mechanical frequency response method was selected. An interactive program of design, testing, and development culminating in the current prototype instrument demonstrated the capabilities of the method and suggested potential applications of the instrument. The resin bolt testing device utilizes a swept frequency dynamic compliance measurement in the 1 to 2 kHz range which is interpreted by an electronic signal processor to give a "GO" or "NO GO? readout. Field tests have shown that the device can reliably determine the bond quality of the front half of the bolt (nearest the roof surface). Tests were carried out on both experimentally installed bolts and typical mine bolts installed by a conventional bolting machine. The development program has led to recommendations for improvement of the prototype and future development work.

Jan 1, 1979

By T. E. Sterner

The Bureau of Mines investigated the use of a chromatographic gas analyzer in determining the concentration of combustion products in gas produced during field and laboratory thermal oil-recovery tests. Several parameters (carrier-gas flow, cell current, sample size, and temperature) known to affect quantitative analyses were studied using a commercially available dual-column, dual-detector chromatographic gas analyzer which had been modified to provide close control of these variables. The apparatus made possible a much closer control of air-and gas-injection rates and provided adequate data for performing material-balance calculations and for determining oxygen utilization during the laboratory and field combustion tests. The chromatographic analysis also aided materially in evaluating and measuring bypassing and gas travel times and in detecting high-permeability zones that were present in the reservoir.

Jan 1, 1965

By Robert F. Chaiken

The U.S. Bureau of Mines conducted an experimental and theoretical study of coupled chemical kinetic and mass transport processes during leaching of pyrite from coal in a counterflow, "trickle-bed" column reactor. Spatial and temporal data on reactant and product concentrations were used as solutions to appropriate continuity equations, which in turn define chemical kinetic reaction rates. Data from four 180-by 30-cm column leaching experiments using coal, coal waste, and air-water and air-FeC13 lixiviants have been analyzed. The rate of leaching was found to be diffusion limited (probably by Fe3+) and not controlled by bacterial action. Rates of pyrite oxidation were found to vary with elapsed time (80 to 225 days) and followed a bell-shaped curve, sometimes with a delay before start of reaction. Maximum rates of reaction ranged from 3 to 10 (mmol/d)/L (column) for coal waste and 0.4 (mmol/d)/L (column) for coal. Reaction was 30 to SO pct complete, probably due to precipitation of product salts (e.g., jarosites), which impede transport of oxidant through the coal. An absorption-desorption model of solids leaching, which considers the role of heterogeneous porosity in solids leaching, was used to describe time-dependent leaching rates.

Jan 1, 2010

By Larry G. Stolarczyk

This report deals with the creation of an efficient method to determine if command, control, communication and monitoring (3cm) equipment in coal, metal and non-metal mines is susceptible to Radio Frequency Interference (RFI) from the Medium Frequency (MF) radio communications system. A qualitative and quantitative RFI test plan was developed for in-mine and laboratory evaluation of the equipment. The laboratory testing was accomplished using the TEM Test Chamber. Detailed information on the Test Plan and the TEM Test Chamber is included. During in-mine testing of the MF System some underground equipment malfunctioned when the transmitter's radiating antenna was in close proximity. Electromagnetic Compatibility (EMC) testing was done on three levels; Component (circuit or box), subsystems and system. Nine tables are included which show the results of testing various equipment for RFI.

Jan 1, 1986

By Frederick W. Lee

List of contributing editors of Geophysical Abstracts:

Sep 1, 1932

By L. C. George, J. W. Jensen

A new system for precisely counterbalancing and measuring vapor pressure operates by servomechanical principles . It was developed with the objective of determining the vapor - pressure equations of metal halides . The system is isolated from the vapor - pressure bulb by a diaphragm transducer that signals a pressure regulator to null any pressure difference that is detected . Pressure measurement and readout are continuously performed by a servomanometer , accurate to ±0.003 cm Hg for the range of 0.1 to 200 cm Hg . High response rate and sensitivity are obtained . Methods of use are described , and results for CdC1 and PbC1 , in agreement with data of other investigators , are given as examples .

Jan 1, 1964

By August J. Kwitowski

The U.S. Bureau of Mines developed and tested a teleoperating system to control a new highwall mining system. A remote operator was provided out-of-sight sensory information and control of coal extraction and haulage equipment. Surface and production testing proved that the teleoperating system supplied the operator with sufficient sensory information to operate the mining system. Details on the teleoperating system provided in this report include (1) sensor selection, (2) a description of the electronic control system, (3) equipment selection and modifications, (4) the positive test results, and (5) recommendations for system improvements.

Jan 1, 2010

The Leuna Factory of the I. G. Farbenindustrie A. G., situated near Merseburg, is the biggest heavy-chemical plant in Germany and produces a very wide range of products, mainly based on hydrogen or hydrogen and carbon monoxide. Its principal products are ammonia, synthetic petrol derived from the hydrogenation of brown coal, and synthetic alcohols made from hydrogen and carbon monoxide. The plant was first, visited on April 21, 1945, by a team including E. Cotton, V. Haensel, E. B. Peck, P. K. Kuhne, H. M. Weir, L. L. Hirst, W. W. Odell, G. U. Hopton, H. Hollings, J. F. Ellis, and H. G. Simpson. It was again visited on May 8-24, 1945, by a combined British and American team consisting of R, Holroyd, M. A. G, Banks, D. A. Howes, A. J. V. Underwood, R. A. Taylor, W. F. Faragher, H. Schindler, and J. G. Allen. This team was later joined by J. F. Ellis and R. J. Morley. A third visit with particular reference to catalyst manufacture was made by W. F. Faragher and W. A. Horne, and the notes of these latest investigators have been taken into account in preparing the report. This report was edited by Dr. R. Holroyd.

Jan 1, 1946

By E. D. Gardner

This is one of a series of papers describing mining and related subjects affecting mining in western mining districts and mineralized areas. The parts of this paper pertaining to current production, mining and milling methods and practices, and general conditions affecting mining were collected principally during a field survey made in May 1935. Some original data obtained on previous visits to the area are also included. The history, geological background, and past production of the mines and district are largely abstracted from previous publications, for which due credit is given later in the test. The principal districts in the Black Mountains are the Oatman or San Francisco and the Union Pass or Katherine. This range contains the principal producing mines of the State, in which gold is the only important metal. Although the total production of gold is relatively small as compared to other districts where the precious metals are obtained as a by-product in copper min¬ing, the area is one of considerable economic importance to the State.

Jan 1, 1936

By A. U. Miller

Since coal -mining records have been kept , reports of all mining States show that each year the lives of many workers have been sacrificed in the production of coal , and Illinois has contributed its share , Illinois reports for the 50 years 1882 to 1932 , inclusive , show that 6,673 men were killed -- 6,121 underground , 340 in the shaft , and 212 on the surface . Of the fatalities underground , 3,116 were caused by falls of roof or sides , 1,111 by haulage , 630 by explosives , 577 by gas explosions , 139 by electricity, and 548 by other causes ; 166 of the shaft fatalities were caused by falling down the shaft , 143 by the cage , and 31 by other causes ; 108 of the surface fatalities were caused by railroad cars , 46 by machinery , and 58 by other causes . Most of those engaged in mining are still of the opinion that it is an extremely hazardous occupation and that it is practically impossible to operate without accidents ; however , students of safety in mining now believe that with the proper attention to accident prevention mining may be conducted with little , if any , greater accident rate than that of other supposedly hazardous industries . There is no mystery connected with accidents in mining ; reports show that the majority are due to two main causes , falls of roof and sides and haulage . Mining companies in Illinois , as well as in other States , have proved in the past few years that the hazards of mining , like those of other industries , can be controlled to a large extent and the mines operated with few if any accidents , provided a great enough effort is made by employer and worker . Although the past accident rate of Illinois may compare favorably with that of other mining States it is higher than it should be ; the fact that 6,673 men (an average of 133.46 per year) were killed in and around the mines of the State between 1882- and 1932 indicates that accident prevention should receive more consideration in the future than in the past .

Nov 1, 1934

By Albert L. Toenges, Theodore R. Jolley

"INTRODUCTION The construction of frame houses (fig. 1) in recent years instead of the conventional sod hut (igloo) (fig. 2) by the Eskimos in the villages along the Arctic Ocean has increased the demand for fuel in these villages. The frame houses, which are not insulated against extreme cold and are difficult to heat, are equipped with Goal stoves. The well-insulated sod huts were heated comfortably with whale-oil stoves. In some years whaling is Door, consequently there is a demand for solid fuel.The Eskimo villages usually are on the sand spits at the mouths of rivers and points of land near the best fishing and hunting grounds. These narrow necks of land usually are sand bars that are not underlain with coal, and coal must be transported to the villages. Lack of development of coal deposits in the Arctic has made it necessary to import coal from the States, generally from 'Washington, to supply these villages. This coal is imported by boat and is received once a year. Its cost is, high, and development of coal deposits in the Arctic to supply these native villages should result in a considerable saving to the Government-operated schools and hospitals as well as to the natives.Early traders attempted to establish coaling stations in the Arctic, and the Eskimos generally know where the coal deposits are situated. A. reconnaissance of a number of deposits in the Arctic was made in the summer of 1946 by engineers of the Coal Division, Fuels and Explosives Branch, Bureau of Mines, and this report describes the areas investigated and suggests plans for the development of some of these deposits."

Dec 1, 1947