Search Documents

By F. D. Everett

This report, based on information made available by four uranium-producing companies, describes the geology, exploration, open-pit development and mining, and shaft sinking in the Gas Hills uranium district of Wyoming. Open-pit stripping features motor-scrapers push-loaded by crawler or rubber-tired tractors. The ground generally can be ripped, and little blasting is necessary. Detailed data are given on grouting for ground stabilization in sinking a small-diameter shaft in the relatively unconsolidated sandstone and siltstone, Cost and performance data are presented as made available by the companies.

Jan 1, 1963

By Ernest W. Loya

The Bureau of Mines has developed a computer program for calculating the composition of gravimetric primary standard gas mixtures. The Fortran IV program applies corrections due to buoyancy variations of the cylinder and inaccuracies of the balance weights. The program also determines the statistical error due to the sensitivity and precision of the balance and applies the analytical error of the weighed gases.

Jan 1, 1985

By Madan M. Singh

Hydraulic mining has been practiced in the United States since 1852 and many mineral commodities, such as gilsonite, phosphates, lead-zinc, silver ores and St. Peter Sandstone can be mined in this manner. In 1958, the U. S. Bureau of Mines initiated research into the mining of coal using these techniques.1-4 These early investigations were conducted in the 5000 psi pressure range. The large nozzle diameters used in this pressure range produced extremely high flow rates which created visibility problems at the coal face, and required removal of large amounts of water from the mining area. Besides, the production rates were not much better than with mechanical methods. This indicated that with higher pressures the water quantities might be reduced using the same or higher horsepowers but enhanced breakage. For this reason intensive investigation in material removal using fine water jets at extremely high pressures (50,000 psi to 100,000 psi) has been undertaken. This was not the entire reason for this contract from the Bureau of Mines, however. The contract objective is outlined later. IIT Research Institute has done pioneering work in high pressure jet development in the United States.5-8 Similar schemes have been investigated abroad. 9-13 Hydraulic mining of coal at relatively low pressures is successfully being done in the Soviet Union, Japan, Canada, and most recently, in Germany.

Jan 1, 1973

By Albert L. Toenges

[sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we. sing tho ppsf; few Yomn t!le:.c. hcs beer. p. trqnd away frorn locomotive haulwe of cop2 frorn tile losdiw point to tho prop,nration plant of bitu~i- nnus-cod strip mlncc to a;~to~lzcd. h,71Jlr.:~. The qrostion has arisen rrhethcr this is alwqvs econ~nicd, rxcl the purpcrse or' tnf s investigation is to de- termine, if possible, the econonic limlt for ~~torieod had.we.]

Jan 1, 1938

By P. G. Clites

A laboratory furnace was developed by the Federal Bureau of Mines for use in studying the interrelationships among variables associated with skull melting and casting high-temperature metals. Although additional work is necessary to determine the extent to which the information obtained by using this furnace can be extrapolated to larger furnaces of the same type, many casting characteristics of metals and alloys can be determined on equipment of this size. This furnace is a laboratory-size, consumable-electrode, skull-casting furnace equipped with a water-cooled copper ladle. The ladle, which is a tilt-pour or over-the-lip type, has a volume of approximately 30 cubic inches and provides up to 20 cubic inches of molten metal for castings. Castings of various reactive and refractory metals, including zirconium, titanium, hafnium, columbium, molybdenum, tantalum, and tungsten, have been produced. In addition, castings of iron, chromium, and copper have been made. The simplicity and versatility of the apparatus would make it useful to metallurgical laboratories preparing cast specimens.

Jan 1, 1961

By A. W. Frolli

This paper, describing the open-cut mining milling, and cyaniding methods and costs at the Yellow Aster gold mine, is one of a series being prepared by the Bureau of Mines on similar practices in the United States. It is presented primarily to show methods and costs of mining and treating low-grade gold ore on a large scale.

Jan 1, 1940

By Robert H. Peters

Groundfall accidents have been the leading cause of fatalities in the underground coal mining industry for many years. Statistics from the Mine Safety and Health Administration (MSHA) indicate that approximately half of the victims of these fatal accidents were in an area where no devices had been installed to support the mine roof. This report was prepared by the U.S. Bureau of Mines to provide guidance to operators of underground mines concerning the use of techniques that may help to keep miners from going under unsupported mine roof. The report is divided into two major sections. The first section reviews the findings from several areas of empirical research pertaining to strategies for convincing employees to avoid unsafe acts and/or adopt self-protective behaviors. The strategies are (1) incentives and feedback, (2) disciplinary actions, (3) training (primarily fear communications and behavioral modeling), and (4) nondirective techniques. This literature review has a broad focus and should be helpful in making decisions about how to encourage a wide variety of types of self-protective behaviors. The second major section of the report presents an analysis of each strategy's potential for keeping miners away from unsupported roof.

Jan 1, 1991

By Lee J. Raabe

A specialized loading system for tensile and fatigue testing of wire rope was constructed and installed in the U.S. Bureau of Mine Wire Rope Test Facility in Bruceton, Pennsylvania. The computer-controlled closed-loop servo-hydraulic test system which can apply up to 800,000 pounds of force on the rope while stretching it up to 30 inches will be used in the development and verification of hoist rope retirement criteria for ropes in the 1 to 2 ½ in. diameter range. Characteristics and capabilities of the system are discussed.

Jan 1, 1984

By K. E. Stanfield

[Asphalt ~~d road oil ar8 the principal products manufactured from Wyor.1in~ Ilblack oilo" \r,hich, beca.use of th?lir hig.~ E\.sphal t and hig} sulfur COi.1Jce~1t, .!?re difficult e':ld costly to refine into hi?;h-gra.de motor f 101s, burning oils. and lucri ants by presont mothods. Accordin~ly. the demand for truHle asphaltic renidl urn for the construction of roade aJ1.d other uses is 3. controlling factor in the quantity of crud~ oil prod ICed. The increasiilg -u.tilization of special aST>ha.lts as ine}""Pensive bonding, in-]

Jan 1, 1941

By Oliver Bowles

"Introduction.During recent months the Bureau of Mines has conducted a detailed study of the slate industry with special reference to increased efficiency in its production, preparation and utilization. The results of these investigations will be incorporated in a forthcoming bulletin. The purpose of this preliminary paper is three-fold. One object is to bring to the attention of slate producers certain modifications in manufacture and classification which would encourage a wider use of slate. A second purpose is to direct the thought of roofers toward the importance of proper laying of slate, and the third object is to acquaint the general public with its enduring qualities.Origin and character.Without entering into any detailed discussion of the origin and history of slate, a subject to be covered in the bulletin mentioned, it may be of interest to the general reader to know that slate is originally formed from mud or soft clay, carried down by streams and laid down in successive layers in deep water. The pressure of superimposed materials gradually compresses the clay into a firm rock known as shale. In many places this shale was, during the succeeding ages, subjected to intense pressure and folding due to mountain-building forces within the earth. This intense pressure, together with high temperature, changed the clay into other minerals such as mica, chlorite, and silica, which are very resistant to weathering, and also developed a very definite cleavage or splitting direction which characterizes the rock as slate. It is this property which renders slate of value for roofing, for, by using a broad chisel and a wooden mallet, a slate worker can readily split it into thin sheets which are later trimmed into rectangles of various sizes."

Jul 1, 1921

By Alexander M. Gow

This paper summarizes a survey of fine-grinding practice in ore-concentrating plants throughout the United States, Alaska, Canada, Mexico, and Cuba as reported in the Bureau of Mines Information Circulars on milling methods. The survey covers 49 concentrators, which have a combined capacity of over 160,000 tons per day. In these plants 470 ball, rod, and pebble mills prepare material for flotation, gravity concentration, amalgamation, cyanidation, and air separation. The ores are those of gold, silver, copper, lead, zinc, molybdenum, feldspar, and pyrite. The metallurgy is that of the period 1928-32. Of these 49 concentrators, 36 are in the United States. They can treat 134,400 tons per day, and they have 326 fine-grinding mills. In the United States there are about 100 active or temporarily idle concentrators, exclusive of the many plants in the Tri-State zinc district, the washeries of the Lake Superior iron ranges and the Florida phosphate area, and small gold and silver concentrators. These 100 plants have an estimated capacity of 290,000 tons per day and employ about 650 ball, rod, and pebble mills. Consequently, since this paper covers about half of the production of this country it may be considered as particularly representative of fine grinding in ore mills in the United States.

Jan 1, 1933

By Roger G. Long

This final report reviews installation, maintenance and inspection of mine pager telephone installations. A Technical Handbook was developed and distributed. Certain commercial telephone test equipment was modified and a tone source and switching circuit were developed for use in the testing of mine pager phone systems. Descriptions are included of the modifications to a commercial test set and of a tone source/ switching unit.

Jan 1, 1975

By James Westfield

A brief résumé follows of activities of the Division of Coal-Mine Inspection that have had a favorable effect on health, safety, and the reduction of injuries at coal mines: 1. The Federal Mine Safety Code fur Bituminous Coal and Lignite Mines of the United States was issued originally by the Director of the Bureau of Mines on July 24, 1946, after consulting with management and labor representatives of the coal-mining industry. The code has been used by Federal coal-mine inspectors while inspecting bituminous-coal and lignite mines as a basis for determining the existence of unhealthful and unsafe conditions and practices in these mines. A revised code was issued by the Secretary of the Interior on October 8, 1953, after further consultations with representatives of management and mine workers and was incorporated by reference in the 1952 and subsequent bituminous -coal wage agreements. The agreement of May 29, 1946, between the Secretary of the Interior, acting as Coal Mines Administrator under authority of Executive Order 9728, and the United Mine Workers of America, covering bituminous-coal and lignite mines in Government possession, charged Federal coal-mine inspectors with the responsibility of making periodic investigations of the mines and reportin; to the Coal Mines Administrator any violations of the Federal Minis Safety Code. Federal coal-mine inspectors also had temporary authority to close mines found to be imminently dangerous, but such authority under Executive Order 9728 was removed on June 30, 1947, when Government control of the mines was terminated.

Jan 1, 1960

By H. A. Thorne

This paper describing the mining practices at the Chino mines at Santa Rita, Grant County, N. Mex., is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Nevada Consolidated Copper Co., Chino mine's, operates an open-cut copper mine at Santa Rita, Central mining district, Grant County, N. Mex. This mine is located about 16 miles east and slightly north of Silver City, the county seat. The ore is-transported in standard railroad cars by the Atchison, Topeka & Santa Fe Railway Co., approximately 10 miles to Hurley where it is milled. The concentrated are shipped approximately l'70 miles over the same railroad to the smelter of the American Smelting and Refining Co., at El Paso, Tex. (fig. 1)

Jan 1, 1931

By L. R. Burdick, J. F. Barkley

"The agglomerating index of coal is an index based upon the nature of the coke residue left when the standard volatile-matter determination of the well-known proximate analysis is made. In this determination a small amount of coal is heated in a container to about 950° C. (1,742° F.), at which temperature the volatile matter is driven off, leaving a coke formation. The coke residues for various coals are quite different in physical structure: and, for some time past, work has been done on studies of the nature of these residues in connection with the coking of coal. In 1934 Gilmore, Connell, and Nicolls proposed use of the agglomerating index for indicating the dividing line between noncaking coals and those having weakly caking properties. 4/ Its use was adopted in the standard classification of coals by rank as a requisite physical property index to differentiate semianthracite from low-volatile bituminous coal and also high-volatile ""C"" bituminous from subbituminous ""A"" coal, as shown in table 1, the standard coal classification adopted by the American Society for Testing Materials and the American Standards Association. 5./In studying the agglomerating properties of coals based on the coke residue the Bureau of Mines has adopted the notation given in table 2. Coals that in the volatile-matter determination give a coke residue either in the form of an agglomerate button that will support a 500-gram weight without pulverizing or a button that shows swelling or cell structure are considered to be agglomerating."

Nov 1, 1938

By Paul W. Johnson, Ralph C. Kirby, Frank A. Peters

An evaluation is presented for a process designed , on the basis of published work , to extract alumina as potassium alum from clay using sulfuric acid and potassium sulfate . The silica residue is separated by filtration . Ferric iron is reduced to ferrous iron , and the alum is crystallized from the solution , leaving the ferrous iron in solution . The alum crystals are separated from the solution and redissolved for feed to autoclave decomposition . In an autoclave the alum is partly decomposed to a basic alum , recovering five - ninths of the sulfuric acid and two - thirds of the potassium sulfate without using an acid plant . The basic alum is decomposed by calcining , and the potassium sulfate is then removed by washing with water . Operating costs for a plant producing 1,000 tons of alumina a day are estimated at $ 96.15 per ton of alumina . The fixed capital cost is estimated at $ 155 million . This process is not competitive under current economic conditions with the production of alumina from bauxite by the Bayer process . Improvement in leaching , basic alum decomposition , and washing could reduce the costs and improve the product which contains some potassium .

Jan 1, 1963

By W. H. Oppelt

The continuous gasification of lignite in an externally heated alloy-steel re-tort was investigated by the Bureau of Mines, Grand Forks, N. Dak., from 1945 to 1951. The main objective of the long-term experimental program was to obtain data on the mechanical performance of this type of gasification retort, particularly the alloy-steel heat-transfer surface of the retort, when operated on large pilot-plant scale. At the same time, extensive experimental data were obtained concerning the effect of process variables and the effect of a limited number of design modifications on gasifier performance. In the period covered by this progress report 4 pilot-plant runs totaling 2,879 hours of operation were completed with the rolled-plate, 310-alloy reaction tube. Over 30 million cubic feet of gas, having H2-CO ratios from 2.1 to 4.4, was made by the partial gasification of 636 tons of 1-1/2-by 3/8-inch natural lignite. Rates of gas generation were from 8,200 to 14,300 cubic feet per hour. Three of the four runs were carried out with the lowered gas offtake or continuous-annulus design modification of the gasification retort. In the final run of the series, gasification of lignite from seven different mines in North Dakota and Saskatchewan, Canada, was investigated at similar combustion-space temperatures and lignite and steam feed rates.

Jan 1, 1955

By J. K. Whyatt

The U.S. Bureau of Mines conducted an overcore stress measurement on the 5300 level of the Lucky Friday Mine, Mullan, ID, to investigate the stress regime around an experimental stope in a rock-burst-prone mine. The result indicated a stress field with unexpected magnitude and orientation [s 1 ?135 MPa (19,600 psi) oriented S 80° W). An unusual amount of rock-burst activity was encountered during subsequent excavation. A careful review of the overcore data suggested the overcore strain measurements were valid. Moreover, concentrated rock-burst activity suggested that the measured stress field did exist, but was localized and therefore did not represent the far-field in situ stress field.

Jan 1, 2010

By Peter Grandstone, D. A. Jessup, D. B. Taliaferro

"INTRODUCTION Water flooding of oil sands in Texas as a means of secondary recovery of oil has been practiced mainly in the north-central part of the State, which includes the old shallow fields in eight counties, extending south through Wichita and Clay Counties on the Red River into Brown County.The Texas Railroad Commission, is empowered ""to promote conservation and prevent waste in the drilling, completion, operation, and abandonment of oil wells"" and ""to issue regulations necessary for fulfillment of these ends,"" granted The Texas Co. the first permit to inject water into the oil-bearing sand on December 7, 1935. The permit was granted after the Commission had conducted a number of hearings, which were attended by many operators interested in that method of secondary recovery. Through December 31, 1944, the Commission had granted 50 permits for water flooding. Of that number, 45 permits were issued for projects in north Texas, the remaining 14 being distributed throughout west and south Texas. By the end of 1944, there were 33 active and 5 abandoned water-flooding projects in the North Texas area, as is in figure I.Oil production in the North Texas area started in 1904 from the shallow sands (ranging from 100 feet to 800 feet in depth) of the Petrolia (or Henrietta) field in northern Clay County. Development was rapid and unrestricted during the boom period from about 1911 to 1918, and considerable waste of both produced oil and reservoir energy resulted."

Jul 1, 1946

Possible consequences of continuing internal political unrest and the imposition of foreign sanctions raise concerns about the traditional reliability of the Republic of South Africa as a major world supplier of important minerals. A recent Bureau of Mines' technical report (Open File Report 76-86) examined the impacts of temporary peacetime disruption scenarios for six key materials and mitigating options. Because of South Africa's dominant producer position for these minerals (except for cobalt), expansion of primary production capacity outside of South Africa is not a short term mitigative option. However, prospects of a longer term disruption would likely spur investment in capacity expansion in alternative Market Economy Country supply sources. This report identifies the resources, production costs, and burdens that would be placed on alternative MEC producers of chromium, cobalt, gold, manganese, and platinum-group minerals if South Africa's production were subject to a long term; disruption. When long term supplies from South African deposits are discounted, more than a few years reserves were found only for cobalt and manganese. Even for these two minerals, higher sustained prices would be required to increase manganese production capacity and to support means of cobalt transportation not through South Africa.

Jan 1, 1986