Search Documents

By R. H. Nafziger

The Bureau of Mines evaluated 18 domestic titaniferous materials with widely varying compositions, mineralogy, and physical properties in electric-arc furnaces, Techniques were devised to recover both the titanium and iron values contained in these materials so that the reliance of the United States on foreign sources of higher grade ilmenites and rutile might be decreased. Most of the tested titaniferous materials responded well to lower grade or byproduct reductants, such as bituminous coals, charcoal, and coke breeze. Sufficient slag fluidity was realized by maintaining from 8 to 12 wt-pct iron in the slags; no contaminating fluidizers were required. Fluid slags containing up to 79, 70, and 54 wt-pct Ti02 were realized from east coast ilmenites, a rock ilmenite, and a titaniferous magnetite ore, respectively. A carbon-lined furnace shell is recommended for minimum slag contamination. Good results also were obtained during extended submerged-arc furnace tests.

Jan 1, 1980

By Mackenzie Burnett

This program was initiated by USBM to quantify the respirable dust problem caused by the use .of roadheaders in underground metal/nonmetal mines with special emphasis on this problem in uranium mines. The contract called for the development of methods or equipment to alleviate the respirable dust and to implement the solution in a mine. Attempts to quantify the dust problem were made in the following way: survey of MSHA records, survey of state mine enforcement agencies, survey of mine records, dust measurements taken at two mines using roadheaders. The results of this study are not conclusive due to very limited and sometimes less than useful data; however, the study does indicate that a serious dust problem could and may exist. If and when roadheader use becomes more popular, it is almost certain that development of dust control procedures and equipment will be necessary. This contract was concluded without developing this equipment since only one roadheader is currently in use in an American uranium mine and the mine prefers not to participate in the program at this time. This report discusses the available data concerning respirable dust problems and presents a solution which can potentially help to solve the problem. The solution requires the use of blowing ventilation, on-board dust extraction at the source, and filtration, as well as continued use of water sprays. The on-site tuning of such a system is necessary to demonstrate the degree of improvement possible.

Jan 1, 1981

By Staff

A major emphasis of the U.S. Bureau of Mines is to perform research on the prevention of fatal accidents at mining operations. The leading cause of fatalities in the underground coal mining industry is groundfalls. This proceedings volume presents several new developments that are helping to prevent fatalities and reduce injuries by groundfalls. The papers focus on the problem from two different perspectives. About half of the papers present information and techniques that can be used to train and motivate miners to protect themselves from groundfalls. The other papers explain how to identify and respond to various geologic conditions that affect the stability of the mine roof. Of the 95 groundfall fatalities that occurred during 1986-90, 75% took place in Kentucky, West Virginia, and Virginia. The rate of groundfall fatalities was much higher at small mines. During 1986-90, the rate of groundfall fatalities at mines employing fewer than 20 people was 4.3 times higher than the rate for larger mines. Because so many groundfall fatalities are occurring at relatively small mines in the southern Appalachian coalfields, many of the papers focus specifically on the needs of this category of mine operations.

Jan 1, 1992

By D. E. Emerson, C. G. Kirkland, E. M. Frost

An apparatus has been developed for determining the helium content of gases containing 40 percent or more helium . It utilizes activated coconut charcoal at liquid nitrogen temperatures to adsorb constituents other than helium in the mixture . Series of analyses have been run where the mean deviation was less than 0.05 percent helium . Twenty or more analyses can be made in an 8- hour day .

Jan 1, 1964

By Edmund S. Leaver

[In previous reports 5/ of ore-testing studies standard methods of conduction tests with precious-metal ores selected as representative of certain mining districts were discussed in considerable detail.]

Jan 1, 1941

By G. R. Hopkins

For several years prior to about the middle of 1928 both the number and capacity of natural-gasoline plants showed a steady increase; this resulted from a material gain in the supply of casinghead has due to the discovery of a number of flush fields with relatively high gas-oil ratios. From 1928 to date some form of proration has been continually in force, with a consequent curtailment in the supply of wet gas. This decline in available gas and a severe decrease in prices, due largely to the increasing competition of light refinery products, has eliminated virtually all of the weaker units during the last 5 years, with the result that the number of plants declined from 1,155 on January 1, 1928 to 19035 on January 1, 1930, to 909 on January 1, 1932, and then to 859 on January 1, 1934, The struggle of the small high-cost producers to exist is illustrated further by the trend in the number of shut-down plants, which has increased from 36 on January 1, 1930 to 100 on January 1, 1932 and to 128 on January 1, 1934. The increase in the number of plants prior to 1929 resulted in a material gain in the total capacity, but the decline in number between 1929 and 1932 was not followed by a corresponding decrease in capacity, as gains resulting from the construction of a few very large plants overbalanced the loss due to the dismantling of a large number of small ones. However, the low prices of 1932 and 1933 supplied little incentive for new construction, and the total capacity declined in approximately the same ratio as the number. Thus the total capacity declined from 11,387,000 gallons daily on January 1, 1932 to 13,060,000 gallons daily on January 1, 1934, Of the latter 9,181,000 gallons (91 percent) represented the capacity of the operating plants and 679,000 gallons (9 percent) the capacity of the idle plants.

Jan 1, 1934

By J. W. Eckerd

This report describes an investigation of the technical feasibility of using a conventional commercial-size (10-ft. i.d.), rotating grate, dry-ash-removal type gas producer to make producer gas from chestnut-size bone anthracite. Test instruments were installed, and some minor changes were made in the equipment to handle the large quantities of materials expected. Extensive tests, lasting about 4 weeks, were planned, using 35 to 50 percent ash chestnut anthracite bone. However, operations were suspended after 8 days when it became apparent that to use this type of fuel satisfactorily substantial changes in equipment and operating procedures would be required. Nevertheless, enough data were obtained to indicate that gas could be produced continuously and routinely from bone coal in this type of producer whenever conditions justified the necessary development work.

Jan 1, 1960

By Oliver C. Ralston

The growing popularity of perlite (sometimes spelled pearlite) as a raw material for thermal expansion into pumicelike products in the Western States has prompted a preliminary investigation of the properties of such material and the problems that want solution to put a perlite industry on a firm foundation. The Bureau of Mines is undertaking the gathering of data and the solution of these problems, and the following paper records some of the available information. and the promise of the material, with some comparisons of advantages of the various competing lightweight aggregates that can be made from siliceous volcanic glasses and rocks containing entrapped or dissolved water that causes their expansion on' quick heating to their softening points. This new industrial rock has caught the fancy of the mineral industry in the western States because it has Fume advantages over natural pumice. Chemically, it is typified as rhyolitic in composition, and one may find obsidian, rhyolite, pumice, pumicite, and perlite from the same vant and contemporaneous in origin. The material need not be rhyolite but should be a siliceous or acid lava and contain 2 to 5 percent water still in "solution" in the rock. On quick heating to the softening temperature the material puffs, due to conversion of the contained eater into bubbles of steam. Slow heating causes gradual release of the imprisoned water by decrepitation and. cracking and-results in, very little puffing. Perlite is often in the form of ovoid volcanic bombs formed by explosive eruption of large masses of lava into the air, where they, quickly cool, with escape of little of the contained water, exceptt perhaps for a hollow interior. Since they cool in layers they have an onion-type structure and a pearly luster from interference of light between the. layers, which is' the origin of the name "perlite." Perlite may occur in intruded flows that have been quickly cooled and partly expanded but retained most of their magmatic water content. Obsidian may be the same lava cooled quickly under conditions that prevented crystallization of feldspars and other minerals, leaving the volcanic glass that may or may not retain all of the original contained water.

Jan 1, 1946

By Albert E. Long

During the summer and fall of 1948 the Bureau of Mines, in cooperation with the U. S. Geological Survey, conducted 6xperiments in diamond core drilling in the Phosphoria formation in southeastern Idaho and southwestern Wyoming. Nearly all of the diamond core drilling in the Phosphoria formation has been done by mining companies interested in finding and developing phosphate-bearing beds amenable to stripping. The recovery of sludge; and enough core (usually 30 to 60 percent) to identify certain marker beds produced by current drilling practices meets both the primary requirement of mining companies in determining depth of overburden and their secondary need to determine the phosphate content of relatively thick minable units whose general composition and nature are already fairly well established.

Jan 1, 1949

By M. N. Plis

This report describes the initial results of long-range research on bit life conducted by the Bureau of Mines. Three commercial bit designs -a round-nose radial, 60° conical, and 90° conical with tungsten carbide (WC) inserts -and five experimental bits were tested. Four of the experimental bits were radial designs using polycrystalline diamond compact (PDC) inserts. The fifth was a 90° conical with an oversize WC insert. Bits were worn on a high-silica sandstone typical of coal mine roofs. The bits were mounted on a 34-in-diam drum section that provided a bit speed of 565 ft/min. Cutting forces were measured on a modified vertical slotter using a three-axis force dynamometer and recorded on an FM magnetic tape recorder. Changes in cutting forces, bit weight, and airborne dust due to gradual abrasive wear and catastrophic insert failure are presented. Tabulated and graphed data, photographs of the progression of bit wear, and selected qualitative visual and auditory observations of the bits taken throughout the experiment are found in the appendixes. The results show that bit life ranged from approximately 16,000 ft for the WC round-nose radial bit to over 125,000 ft for a PDC round-nose radial. Performance, in terms of bit life, cutting forces, wear rate, frictional sparking, machine vibration, and noise was in general best with the PDC bits, followed by the rotating WC bits, with the nonrotating WC bits (round-nose radial and locked 60° conical) being the worst. The results show variations in the included tip angles of new conical bits have an insignificant influence on bit performance when the effects are averaged over the life of the bit. In addition, new bits were generally found to entrain more primary respirable dust for a given cutting distance than worn-out bits. It is hypothesized that this is due to the difference in frictional behavior between new and worn bits. The results from these tests are being used in the Bureau's cutting system model (CSM).

Jan 1, 1988

By Victor Kalcevic

A gas-flow retort for thermal processing of oil shale to recover shale oil was developed by the Bureau of Mines at its Oil-Shale Demonstration Plant, Rifle, Colo., from 1948 to 1952. The retort is a crossflow gas-to-broken-solids heat exchanger. The heating medium is the gas produced in the shale retorting process. The gas is heated in specially designed stoves outside the retort and recycled to the retort. Oil shale from the Mahogany ledge section of the Green River formation in northwestern Colorado was the material processed. Indicated maximum oil recoveries for 20-to 25-gallon-per-ton shale in a l2-inch-thick shale bed and a 20-inch bed are 96 and 91 weight-percent of Fischer assay, respectively. Heat requirements for maximum recovery are 600 to 750 B.t.u. per pound of shale. Properties of the recovered shale oil are affected slightly by shale-bed thickness and extent of retorting. Oil recovery from oil shales assaying over 30 gallons per ton is lower than that from leaner shales.

Jan 1, 1959

By Richard I. Barnhisel

At the Sinclair Study Site it was found that the deeper the soil the greater the yield of corn, soybeans, wheat, alfalfa, and timothy. Yields at this location were generally lower than those at the Alston Surface Mine. At Alston the non-prime land treatments generally produced greater yields for all crops than did the prime farmland treatments, however, the intermediate soil thickness, 20 cm topsoil over 40 cm of subsoil, gave the best yields, provided it's subsoil had been limed. From a chemical point of view, acidic spoils do not need to be buried by 120 cm or 4 feet of soil, provided adequate lime is applied to these spoils as a barrier prior to placement of good quality topsoil and only forage crops are to be grown. The burial depth must be increased to as much as 75 cm when grain crops such as corn or soybeans are to be grown. This response to burial depth appears to be related to water storage needed by the crop and not due to toxic effects of the spoils. A conventional farm tractor-mounted subsoiler increased yields of soybeans and corn the first one or two years, but the effect was diminished with time. Subsoiling did not produce significant increases for alfalfa or wheat. However, ripping with a bulldozer produced significant yield responses, especially for corn and soybeans, that have lasted for at least three years. The ripping effectively reduced the bulk density at least within the zones through which the ripper had passed. Liming the upper 20 cm of subsoil significantly increased yields of alfalfa, corn, and soybeans. There also appeared to be an interaction between this lime treatment and soil depth. Yields of some grain and forage crops may be high enough to meet target levels for bond release for prime farmland. Based on the present study, one should not expect corn yields to be high enough to meet bond release. This statement should not be considered final since the experiment is not complete.

Jan 1, 1983

By D. R. Wilburn

The Bureau of Mines investigated the potential availability of magnesium from 45 properties in market economy countries (MEC's). The 38 significant deposits evaluated have demonstrated resources of approximately 29 billion short tons (st) magnesium-bearing material containing 416 million short tons (MMst) magnesium oxide (MgO). Using data it gathered, the Bureau determined the magnesium production potential for each property including a 15-pct rate of return on invested capital. Total and annual availability assessments for the next 30 yr were completed for magnesium (Mg) metal, deadburned MgO, and caustic calcined MgO. At a January 1984 market price of $1.34/Ib Mg metal, the properties evaluated could economically produce an estimated 13 MMst Mg metal. At a market price of $400/st nonmetal magnesium product, these properties could economically produce 109 MMst deadburned MgO and 43 MMst caustic MgO. These properties could produce approximately 301,000 st Mg metal, 3.0 MMst deadburned MgO, and 430,000 st caustic MgO annually at current full production levels and 1984 market prices until at least the year 2000. Total 1984 MEC production assessed in this study was 153,000 st Mg metal and 4.3 MMst nonmetallic MgO products.

Jan 1, 1986

By H. M. Cooper

The determination of moisture in coal is an empirical test, because the time, temperature, and equipment are specified. The essential features of the equipment and details of the procedure are given in A.S.T.M. Designation: D271-44.:2. According to the specifications, the following features should be incorporated in the equipment used: 1. Oven must have uniform temperature in all parts. 2. Oven must be constructed with minimum of air space. 3. Oven must have means of changing the air two to four times per minute. 4. Air must be dried over sulfuric acid (sp. f-7. 1.84). The analytical procedures governing most of the nation's coal purchases are those given in A.S.T.M. Standards referred to above. These standards are general arid of such scope as to cover all ranks and types of coal. In cases where only the moisture is required, a faster method than the standard procedure is desired.

Jan 1, 1948

By Frank E. Williams

This Bureau of Mines report deals with the urbanization of Tucson, Ariz., a southwestern city with an arid environment. Zoning regulations concerning known aggregate sources are described, and information relating to projected needs for the urban area is furnished. History of growth is outlined not only for the local aggregate industry, but also for the entire urban area. Past conditions are pointed out and background material for future conditions is provided.

Jan 1, 1967

By Howard J. Pincus

The purpose of the study is to investigate the effects of fracture fillings and associated alteration on the mechanical behavior of rocks. Experimental results are presented for 98 specimens from the Climax mine, which were tested since the annual report (May 1973). The conclusions reached are based on both these results and those reported in the annual report. The locations studied are the Climax and Henderson mines in Colorado and the San Manuel mine in Arizona. The rock types studied from each location are from: 1) Climax, medium-grained granite, fine-grained granite, granite porphyry, schist, and gneiss; 2) Henderson, rhyolite porphyry; 3) San Manuel, quartz monzonite and quartz monzonite porphyry. A description of the rocks was made including: color, texture, mineralogy, composition and fabric of fracture fillings, density, apparent porosity, and optical diffraction patterns. Unconfined and triaxial compression tests were run on the Climax and San Manuel specimens. Sonic velocities were measured during the compression tests; Shore sceleroscope hardness was measured before the compression tests. Conclusions are that some relation appears to exist between compressive strength and the following properties and features for all specimens: dynamic Young's modulus, sonic velocity, density, rock composition, slope of velocity curve, composition and fabric of fracture fillings-veinlets, and apparent porosity. There appears to be some relation between compressive strength and Shore scelerscope hardness for the quartz monzonite (San Manuel). A relation appears to exist between texture and compressive strength and the extent of failure on fracture fillings for schists, gneiss, and fine-grained granite (Climax). The amount of swelling clays (montmorillonite, hydromicas, etc.) present in the rock and the relative number of fractures in which they constitute of major portion of the fracture fillings are related to the strength of the rocks. Possible tests for checking the amount of these clays present is presented including saturation, dyes, and X-rays. A useful index relating to rock strength, as revealed in this study, is the presence of swelling clays in detectable abundances. These clays can be detected in the field with a simple wetting and striking test; in the laboratory they can be detected by X-ray and dye methods.

Jan 1, 1974

By Robert L. Montgomery

Heats of solution of samarium (III) oxide and chloride in hydrochloric acid and of samarium (III) oxide, sulfate, and hydrated sulfate in sulfuric acid were measured. The heats of solution of this hygroscopic oxide are larger than those from the literature, probably because of more complete removal of water in the present study. From the literature value for the heat of combustion of samarium, the heats of formation of samarium (III) chloride and sulfate are -244.18 ± 0.41 and -928.5 ± 1.6 kcal./mole, respectively. The heat of hydration of the sulfate is -34.7 ± 1.0 kcal./mole. The heats of formation of other samarium com-pounds have been recalculated, using the new data.

Jan 1, 1959

By F. J. Bailey

"In the fall of 1919, the U.S. Bureau of Mines began an inquiry as to the possibility of utilizing airplanes in conjunction with its rescue work, for quickly transporting engineers and oxygen rescue-apparatus to mine disasters.It was realised that this proposed use of airplanes has serious limitations, and if it were feasible, that the Bureau would have to rely on the cooperation of the established aviation fields of the U. S. Air Service for furnishing airplane service. Therefore Van. H. Manning, Director of the Bureau of Mines, under date of October 28, 1919, wrote the Director of Air Service outlining the rescue and first aid organization of the Bureau, the location of headquarters of district engineers, the distribution of safety cars and stations, and other essential details, and asking whether the Air Service could cooperate with the Bureau in the event of serious mine disasters. Major-General Charles T. Menoher, Director of Air Service, responded that the Air Service would be glad to cooperate insofar as possible, and designated those Air Service stations nearest the district engineers' headquarters, which might be best able to assist.The Bureau of Mines has ten mine rescue cars and eight mine safety stations distributed throughout the mining regions of the United States. The cars are each equipped with sets of oxygen mine-rescue breathing-apparatus and first-aid supplies. The car personnel consists of a mining engineer, surgeon, foreman, first-aid miner, clerk and cook. A foreman miner is in charge of each station and at five of the eight stations are mine safety trucks. The work of the cars and stations is two-fold; (1) Assisting in rescue and recovery work at mine disasters, and (2) training miners in mine rescue and first-aid methods, and in investigations looking to prevention of mine accidents. The country is divided into nine safety districts, with nine district engineers in charge."

Apr 1, 1920

By Lucia Kuizon

The Antimony RARE II area is underlain principally by Mesozoic igneous rocks associated with the Sierra Nevada batholith. The San Andreas fault zone is near the southern boundary. Metallic mineral deposits are associated with the fault zone. These deposits were formed from magmatic solutions, and tend to be along shears and fractures within the country rock. Marble and dolomitic marble deposits occur in Paleozoic roof pendants or inclusions in the Mesozoic intrusive rocks in the area (Troxel and Morton, 1962, p. 52).

Jan 1, 1982

By Don Belsher

Work on contract H0272007 is summarized for the period of 1 February 977 to 1 February 1978. The initial evaluation of two potential systems for the location of well casings, voids, and tunnels in coal are described. The pulse measurement equipment used for the evaluation of the antennas selected possible use with a pulse time domain system and an FM-CW system is described. A TEM horn antenna design potentially suitable for use with these systems is given. An operational comparative analysis between various antenna types is presented.

Jan 1, 1978