Search Documents

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 2010

By H. R. Beard

The citrate process for sulfur dioxide emission control was developed in pursuit of the Bureau of Mines goal of minimizing the adverse environmental impact of mineral-processing operations. This publication describes the gas analysis procedures used during development of the process. The research required the capability to analyze SO2, H2S, CO, CO2, COS, volatile hydrocarbons, NO, NO2, O2, N2, and H2. The methods described include gas chromatography, electrochemical detection, infrared spectroscopy, and the use of a computer program to predict the product composition in complex reactions. Laboratory and pilot plant applications are discussed.

Jan 1, 1979

By G. E. McElroy

This paper3/ is one of a limited series being prepared by the Bureau of Mines to supplement a more extensive series on mining and preparation methods in the various mining districts of the United States. It describes ventilation methods and practices at the anthracite collieries in the Northern field of the anthracite measures of Pennsylvania as obtained by personal inspections in twenty of the larger collieries during 1933 and 1934 and from supplementary information furnished then and later by operating officials. This field is one of the four major divisions - Northern, Eastern Middle, Western Middle, and Southern - into which the anthracite deposits of Pennsylvania are naturally divided, and constitutes, in plan, a slightly bowed lens, about 60 miles long, and that extends from Forest City on the north through Scranton, Pittston, Wilkes-Barre, and Nanticoke to Shickshinny on the south with a. maximum width of 6 miles. It is the oldest and largest producing field of the four, and has produced continuously from 1S09. The total anthracite production for the State reached a peak of about 100,000,000 tons a year in 1917, but in recent years production has averaged about 50,000,000 tons, of which somewhat over half comes from this Northern field. The operations of three of the largest producing organizations in the State are almost wholly included in this field, as well as about half of the operations of two others of the six largest producers, It comprises the first 14 of the 25 numerically designated anthracite State inspection districts.

Jan 1, 1937

By J. R. Nettle

A method has been developed in the laboratory for successfully electro-refining titanium metal. Refining is accomplished in e fused-salt electrolyte using offgrade metal as the anode and collecting the purified metal at the cathode. The characteristics and requirements of the various alkali chlorides tested as electrolytes are discussed in relation to relative ease of purification and serviceability. The various types of cells designed and tested for electrorefining are illustrated and their method of operation discussed. The individual advantage of each cell and the purpose for which it was designed are reviewed. The magnitude of the cathode current density was found to depend largely upon the quantity of soluble titanium chloride in the electrolyte. The physical condition of the anode also greatly affected the cathode current density.

Jan 1, 1957

By Frank A. Peters

The Bayer process treating Jamaican bauxite was evaluated from an economic standpoint, using standard estimating methods and published data, to present a reference point for cost estimates for nonbauxite alumina processes. The estimated operating cost for a plant producing 1,000 tons of alumina a day is $47.96 per ton of alumina when charging $8 per ton for bauxite and $2.30 per hour for direct labor. The estimated fixed capital cost is $46 million.

Jan 1, 1966

By Edward D. Thimons

Inflatable stoppings are currently marketed for production use, and numerous mining companies have become interested in using such stoppings in rescue and recovery operations. The Bureau of Mines therefore evaluated the concept of using inflatable stoppings in emergency situations. The stoppings tested by the Bureau were 12-foot-diameter spheres inflated with a blower operated by a small battery pack. Experiments were conducted with the stoppings in a full-scale wooden mine model to evaluate their ability to withstand sliding or slipping at various internal and differential pressures, puncture resistance, various inflation techniques; and internal leakage from the stoppings. The stoppings were then installed and tested in the Bureau's Safety Research Coal Mine at Bruceton, Pa., to determine their effectiveness as mine air barriers. Despite some encouraging results obtained with the model and in-mine studies, the stoppings did not perform well in two operating metal mines where they proved difficult to erect and inadequate as air barriers.

Jan 1, 1976

By Larry L. Anderson

Enormous quantities of organic wastes are produced each year in the United States. The total amount is in excess of 2 billion tons and at least 880 million tons of this is moisture- and ash-free organic material (dry organic solids), representing a potential energy source of significant magnitude that is not being utilized. Bureau of Mines scientists have developed methods for converting these wastes to convenient energy forms. This report itemizes and evaluates for the first time in detail the quantities and sources of moisture- and ash-free organic material contained in manure, urban refuse, industrial wastes, sewage solids, and agricultural wastes in the United States. Furthermore, estimates are presented for amounts of organic wastes collected or concentrated. The potential for fuel, either oil or gas, from both the total organic wastes generated and those collected or concentrated is also estimated.

Jan 1, 1972

By Norma R. Golumsic

Gasoline and other liquid fuels may be obtained from coal by direct and indirect hydrogenation.3/ The direct process, usually termed the coal-hydro-genation or the Bergius process, was patented in Germany by F. Bergius in 1914 and developed to a commercial stage by the inventor and I. G. Farben-industrie. From a chemical point of view, the coal-hydrogenation process consists of adding hydrogen to the complex coal molecules and removing oxygen so that its chemical constitution is changed to that of petroleum, whereupon the coal substance liquefies, yielding an aromatic crude oil. In the indirect-hydrogenation process, known as the Fischer-Tropsch process (invented by Franz Fischer and Hans Tropsch in Germany), coal, lignite, or natural gas is first converted to water gas, a mixture of carbon monoxide and hydrogen. This mixture of gases, in proper proportion and after suitable purification, is then passed over a solid catalyst at relatively low pressures (1 to 20 atmospheres) and temperatures ranging from 180° to 260° C. The products obtained are gasoline, Diesel oil, liquefiable gases, and paraffin wax.

Jan 1, 1946

By Forrest T. Moyer

The National Safety Competition was inaugurated in 1925 by the Bureau of Mines, U.S. Department of the Interior, in cooperation with the Explosives Engineer. In the first nationwide contest, 210 mines and quarries were enrolled. In 1962, the thirty-eighth anniversary of the competition, 910 mines and quarries were enrolled. These participating plants were worked a total of 133,292,989 man-hours. Of the enrolled plants, 415 achieved injury-free operations for the year, the largest number of perfect safety records in the history of the contest.

Jan 1, 1964

By James T. McCartney, Joseph D. Davis

For more than 10 years coke-oven technologists have been investigating the expanding properties of coal on a scale larger than that afforded by laboratory test tubes. Koppers 4/ was among the first to realize that coals can not be differentiated satisfactorily with respect to expansion in coke ovens by the simpler test-tube methods; in his first method 80 grains of fine coal were coked in a cylinder heated from the bottom, so that the zone of fusion (plastic layer) advanced from the bottom to the top. The scale of test was too small; it has been modified by other investigators, but without significant improvement in practical application of the results. Somewhat later Koppers and Jendne 5/ experimented with a small-scale coke even, one wall of which was movable, in which the layer-coking in a coke oven could be simulated closely. This oven was heated from both sides. Their results with this oven showed a peak in the time-pressure curves near the end of the coking, period when the two plastic layers, advancing from opposite walls, meet. They also found that although the smaller oven was heated from one side only and did not show the Pressure peak characteristic of two-sided heating, it still gave results entirely too high. Russell built an oven similar to the movable-wall oven of Koppers and Jenkner and compared results obtained in it on Beckley expanding coal with these obtained on the some coal in the Altieri 7/ small-scale apparatus. Both tests were conducted at the same constant pressure, but heating was from two sides in Russell's oven and from one side in the Altieri tester. Russell found that the two types of test gave comparable results under constant pressure conditions even though the heating procedures were quite different. He showed later, however, that a "borderline" coal 8/ that contracted in the Altieri tester at constant pressure developed a peak pressure of 4 pounds per square inch in the movable-wall oven heated from both sides at constant volume. He concluded from this that testing at constant volume gave results more accurately indicative of dangerous expansion tendencies than those at constant pressure. He also found that heating from both sides in this oven gave higher pressure than heating from one side only.

May 1, 1942

By R. V. Ramani, K. Bode

"IntroductionThe theory of particle dispersion and deposition in turbulent flow is important to many fields of science and engineering. Dispersion has been studied in some detail since the early fifties (Taylor, 1954; Fischer, 1967; Osipov and Grekov, 1968; Skobunov, 1970 and 1973; Klebanov and Martynyuk, 1974). A broad research effort has also been underway in studying the mechanics of dry particle deposition. Friedlander and Johnstone (1957) proposed a theory, according to which particle deposition from vertical pipe flow could be described by an eddy diffusion transport followed by a final flight to the surface. There have been numerous revisions and additions to this original theory (Owen, 1960; Liu and Agarwal, 1974; Liu and llori, 1974; El-Shobokshy and Ismael, 1980) The mining process essentially consists of breaking in situ materials and transporting them out of the mine. An inherent characteristic of this process is the generation of fine particles. Fine airborne particulates are associated with a number of threats to the health of the miners; fine coal dust can also result in mine-wide catastrophic incidents such as dust explosions. For these and other reasons, it is important to understand the behaviour of airborne dust particulates, particularly their generation, entrainment, transport, dispersion, and deposition in the mine environment for their control.Mine related studies on dispersion and deposition have been few. Yet, several studies of gas and dust dispersion, diesel exhaust contamination, and methane ingress into mine workings have recognized the need for developing reliable parameter values for fundamental understanding of the phenomena (Da""Yes and Slack, 1954; Hodkinson, 1957; Hodkinson and leach, 1958; Mass and Wildschut, 1966; Airey, 1969; Courtney et al., 1986; Stefanko, Ramani, and Thakur, 1974; Stefanko, Ramani and Kenzy, 1977; Bhaskar, 1987, Bhaskar and Ramani 1990; Qin and Ramani, 1989; Shankar and Ramani, 1990)."

Dec 1, 1995

By Thomas L. Ochs

The Bureau of Mines is investigating the fundamental behavior of electric arcs in electric furnace operations. The electric arc is a poorly understood phenomenon. If the arc in a steelmaking furnace can be more carefully controlled, it should be possible to increase heat transfer to the melt, reducing both electrical and acoustical noise. As a first step toward a better understanding of the are, voltage and current signals from operating furnaces were analyzed. The results of the initial analysis show that instrumentation used in monitoring and controlling furnaces, such as meters and strip-chart recorders, gives incomplete or erroneous information to the operator and therefore leads to less than optimal control. Advanced instrumentation and analysis techniques, such as the waveform analysis used in these investigations, can improve the understanding of operation and the control of electric furnaces. This report describes the instrumentation and the numerical analysis methods used and compares these methods with standard metering and recording techniques.

Jan 1, 1986

From time to time the Bureau of Mines has interpreted and applied certain provisions of the Federal Coal Mine Safety Act and Federal Mine Safety Codes, primarily for the guidance of Federal Coal Mine Inspectors. Although interpretations of the Act have appeared in the Federal Register, the Code interpretations and practical applications have not been published. In response to many requests from representatives of the coal-mining industry, the Bureau is publishing this information to promote better understanding of those provisions that may be misinterpreted or misapplied. INTERPRETATIONS AND APPLICATIONS Two Federal Mine Safety Codes are discussed in this report, namely the Federal Mine Safety Code for Bituminous-Coal and Lignite Mines of the United States, Part 1, and the Federal Mine Safety Code, Anthracite Mines of the United States, Part 1. In this circular the word Codes refers to both directives; Code* refers to the code for bituminous-coal and lignite mines; Code? refers to the one for anthracite mines. Act* refers only to bituminous-coal and lignite mines.

Jan 1, 1963

By Robert C. Gabler

Three filter cloth fabrics commonly used in drains for coal waste embankments were tested by the Bureau of Mines for clogging behavior and deterioration under simulated field conditions. The objective was to provide guidelines for the mining industry for the proper selection and use of filter cloths to assure safer embankments at mine waste disposal sites. The filter cloths were tested with three coal waste samples in stand-pipes used to simulate coal mine waste disposal environments. Two of the cloths showed a tendency to become clogged with fines from the wastes. One waste caused clogging by precipitating an iron-silicon compound on the test cloths. No apparent cloth deterioration resulted from exposures to the simulated coal waste environments. (The exposures ranged from 2 to 12 months.) In other tests, exposures to waters in the pH range of 2 to 12 and to reagents used in coal-preparation plants resulted in insignificant or no deterioration, as measured by tensile strength. However, long exposures to sunlight (ranging from 4.6 to 6 months) caused major deterioration in two of the cloths (86-and 98-pct losses in tensile strength) and slight deterioration in the third cloth (9-pct loss in strength).

Jan 1, 1984

By Leland A. Yerkes

Refining aluminum from crude aluminum alloys by the subhalide reaction was investigated to develop a method of producing aluminum by means other than electrolysis of its oxide. The best materials and design for the apparatus and also optimum operating conditions, including temperature, pressure, vapor flow rate, and composition of alloy charge were studied. In the subhalide process, aluminum-trihalide vapor reacts with aluminum in the alloy under high temperature and low pressure, forming volatile aluminum monohalide which reverts to aluminum metal and aluminum trihalide on cooling. The only halide used in this investigation was aluminum trichloride. The crude aluminum-silicon alloys used as the principal raw material contained from 21.9 to 36 percent aluminum, and significant quantities of iron and titanium. These alloys were produced by direct electric smelting of clays. Graphite tubing that was heated by an induction coil proved to be satisfactory material for the laboratory reactor chamber, Enclosed in an insulated glass or quartz pipe, the reactor was used in both vertical and horizontal positions with various baffle and tray arrangements for directing the trihalide vapor both over and through the alloy. Aluminum trichloride vapor was generated in the sublimer at one end of the glass pipe, passed into the reactor where contact was made with the crude alloy, and aluminum monochloride gas was formed. When the gaseous mixture of aluminum monochloride and unreacted tri-chloride passed out of the reactor and entered the condenser, the gases were cooled to 900° C. or less, causing the monochloride to disproportionate into aluminum and aluminum trichloride vapor. The aluminum was deposited on the condenser walls while the aluminum trichloride vapor was carried out of the condenser and into the opposite end of the glass pipe where it solidified on the cooled copper coils.

Jan 1, 1961

By Alan D. Hartman

The U.S. Bureau of Mines, under a Memorandum of Agreement with the American Society of Mechanical Engineers (ASME), established design criteria for a facility to melt residues from municipal waste combustion. This facility, which is available to potential users on a cost-sharing basis, is also applicable to a variety of inorganic waste materials from smelting or melting operations. The design consists of a mechanical feed handling system, electric arc melting furnace, fume-offgas handling system, and thermal oxidizer for final offgas treatment. Screw conveyors and a bucket elevator deliver up to 2,000 lb/h of minus I-in material to a three-phase electric arc melting furnace. This unique 800-kV?A furnace has a water-cooled shell and roof to minimize interaction of the melt with the refractory lining. The volume of the hearth below the slag taphole is approximately 1.2 st of steel. The furnace is sealed, allowing atmosphere control within the furnace and fume duct by nitrogen or inert gas injection. A jet-pulsed baghouse removes particulate from the offgas and serves as an acid gas scrubber. The clean offgas is heated to 1,800° F for 1 s in a propane-fired thermal oxidizer before being vented to the atmosphere.

Jan 1, 2010

By V. A. Marple, K. L. Rubow

"4.1 IntroductionIn previous chapters impactors have been described as useful instruments for classifying particles by their aerodynamic diameters and for measuring particle size distributions. These impactors can be used most reliably if the user has some understanding as to how the impactor classifies particles and what parameters are important in this classification process. This understanding can best be obtained by a theoretical inspection of inertial principles.This chapter reviews the most recent theoretical impactor work and the latest theoretical efficiency curves. Procedures are then given for using these efficiency curves in the design and evaluation of cascade impactors. Finally, several examples are given comparing theoretical and experimental efficiency curves, pointing out when the theory can be used with great confidence and when the theory should be used only as a guideline.Due to the rather simple principle of operation of an inertial impactor (i.e., the impingement of a jet of particle-laden air on a flat plate) the impactor readily lends itself to theoretical analysis. Three notable works in the early 1950,s were those of Davies and Aylward (1951), Davies et al. (1951), and Ranz and Wong (1952).Davies and Aylward (1951) used a method of conformal mapping to obtain an analytical solution to Euler's equation for the flow of a frictionless fluid through a rectangular impactor. Numerical calculations were then carried out whereby the equations of motion of the particles were solved in a stepwise manner, leading to a determination of the efficiency curves. Since this theory assumed potential flow, the effect of Reynolds numbers on the characteristics of the impactor could not be determined.Ranz and Wong (1952) used an approximate flow field to calculate the efficiency of both round and rectangular nozzle impactors. In the vicinity of the stagnation point, the flow field was assumed to be that of frictionless stagnation flow. Here, the resulting equation of motion for the particles was found to be in a form similar to equations for free vibration with viscous damping. Therefore, the known solutions of the vibration equations were applied directly to the problem and the efficiency curves calculated. This solution technique, however, could not take into account the various geometric variations such as the jet-to-plate distance in the determination of the efficiency curves.The work of Ranz and Wong (1952) was later modified by Mercer and Chow (1968) and Mercer and Stafford (1969) so that the rather simple flow fields of Ranz and Wong (1952) could be used to account for various jet-to-plate distances. The same techniques, however, were used to determine the impactor collection efficiency curves."

Jan 1, 1986

By Henry P. Wheeler

As recently as 1915, helium was available only in very small quantities at a cost equivalent to $2,500 per cubic foot. It was a laboratory curiocity, and its properties were of interest to a limited number of scientists (11).3/ During the past 30 years, however, helium has grown from a plaything of scientists to a factor of importance in the prosecution of the recent war. Navy blimps filled with nonflammable helium proved to be more than a match for German submarines operating in the Atlantic. American bombers were able to fly unheard-of distances to drop bombs on Tokyo, Nagoya, Yokahama, and other Japanese cities because they had been made lighter with magnesium, arc-welded in a helium atmosphere. The Army utilized helium-filled radio-sonde balloons to obtain vital information concerning weather conditions affecting D-day invasions and other military maneuvers.

Jan 1, 1946

By Alfred Bellows

The objective was to develop and design a remotely operated temporary roof support system that provides a safe working environment between a freshly cut coal face and the last line of permanently supported roof in which to perform roof bolting activities. This system was to take the form of a retrofit package which could be adapted to a majority of the bolters currently in service. The result is an integrated piece of hardware which will retrofit onto virtually all single boom bolters by removing the drill boom and relocating and modifying the hydraulic controls. The system is composed of three basic components: a pair of cantilevered roof supports which reach forward to the desired line of support, a mast type drill unit for drilling holes and torquing bolts, and a transverse slide assembly to carry the drill from hole to hole across the entry without relocating either the bolter or the roof support. A converted bolter not only provides a much safer operation but is projected to increase the production speed as well as reduce the manpower required to operate a section.. This improvement in productivity is shown to make the job of retrofitting a bolter cost effective in less than two months and provide a potential profit thereafter. Based on the findings presented in this report it is recommended that a proto-type be built and tested in an underground coal mine to demonstrate its effectiveness.

Jan 1, 1976

By ALICE V. Petar

Through the courtesy of the State Department, the Bureau of Mines has received a compreensive report on the jede industry of Burma, pre- pared by American Consul Winfield H. Scott, Rangoon, Burza. This mater- ial is the main basis for the present circular, although free use also has been made of reports on the jede industry in China and Germany by consular officers in those countries, to whom footnote credit is given. The word "jade" is said to be derived from the Spanish "piedra de ijada" (hijada) meaning, literally, "stone of the side," as jade was supposed to cure pains in the side; nephrite (a jade mineral) was named from the Greek word meaning kidney, because it was formerly warn as a re- medy for kidney diseases. To the Burmeso, jade is known as "Kyauksein," or green stone, and to the Chinese, all varieties of the material are referred to as "Yu" or "Yu-chi", According to Confucius, jade was symbolical of. justice, harmony, intelligence, and humanity, and the Chinese of today believe that by using ornaments made of this stone, the wearer is. protected from the "evil eye" as well as from diser.se. Ornaments of carved jade were known to the ancient civilizations of Mexico and Peru and to the peoples of other sections. of Central and South America, Jade ornaments also have been found in the lake dwellings of Switzerland and in Crete; thile in China, as far back as the Chou dynasty (B. C. 1122 B. C. 255) it was used in the production of various classes of precious vessels and as insignia of rank.

Jan 1, 1936