Search Documents

By L. Y. Sadler

The Bureau of Mines conducted a study Lo determine the loss in weight of silica (Si02) volatilization from low-alumina (A1203) refractories used as hot face liner materials in such process equipment as coal gasifiers, synthesis gas transfer lines, and ammonia plant secondary re-formers. Small specimens of 80-and 40-pct-A1203 brick and 95-pct-SiO2 brick were exposed to steam in high-pressure furnaces at pressures of up to 1,000 psig and temperatures up to 1,400° C for periods ranging up to 120 h. Weight losses from the 40-pct-A1203 brick after 40 h of exposure were highest, 2.75 pet at 1,400° C and 1,000 psig. The rate of weight loss had dropped to near zero after 80 h of exposure at all temperatures. No relationship between total silica content of the specimen and weight loss could be established nor did scanning electron microscopic examination of the specimens before and after exposure identify specific regions (e.g., surface) suffering a disproportionate share of the silica loss. It was concluded that minor silica volatilization is likely to occur, if at all, at temperatures of less than 1,000° C and pressures below 1,000 psig, and that low-alumina refractories should be used as dry-ash coal gasifier hot face linings.

Jan 1, 1986

By D. S. Kingery

Owing to changes in State mining laws, the Maryland Bureau of Mines requires all mine foremen to have a thorough, practical knowledge of mine gases and the limitations and use of recognized gas-detecting devices. This requirement involves immediate training of second-grade mine foremen and aspirants to qualify them for certification under the new law. Cooperation of the Federal Bureau of Mines was requested, and a plan for training was discussed and adopted. The methods used in Maryland aroused unusual interest by participating individuals, and the final results were very satisfactory. Consequently, it is thought that this plan will be of interest and assistance to other organizations faced with the need for such training.

Jan 1, 1952

By G. R. Hopkins

According to reports as of January 1, 1931, the total daily charging capacity of the cracking plants, hoth completed and under construction, in the United States amounted to 1,950,781 "barrels, an increase over the previous year of 14 per cent. The total daily capacity of the operating plants amounted to 1,594,990 "barrels, or 82 per cent of the grand total, the capacity of the in¬ operative plants was 244,661 "barrels, or 12 per cent of the total, while the capacity of the plants under construction amounted to 111,130 "barrels, or 6 per cent. In comparison with a year ago, these data indicate a decline in the total capacity of the plants "being "built "but show material increases in the capacity of "both the other two classes. The increase in total inoperative capacity and the decline in construction in 1930 undoubtedly resulted from un¬ satisfactory economic conditions. The total number of cracking units completed or under construction on January 1, 1931, totaled 1,863 as compared with 2,002 the previous year and with a high of 2,559 on June 1, 1926. During the period between June 1, 1926, and January 1, 1931, the total charging capacity of the cracking plants has more than doubled, but the number of units has shown a material decline. This condi¬ tion has been brought about largely through the dismantling of many Burton still of small capacity and through the tendency to increase the size of the new units The "largest unit that can be identified in this survey has a daily charging capacity of 10,000 barrels, but undoubtedly there are some that would exceed this in size. Texas, with a total of 575,300 barrels, ranked far ahead of the other States in charging capacity, and was followed in order by California, Indiana, Oklahoma, and Pennsylvania. Indiana, with only five refineries, ranked third in cracking capacity, which illustrates the importance of the Chicago district as a gasoline-producing center. Not all of the States showed a gain in capacity during the year; in fact, four of them, namely Illinois, Louisiana, New York, and Oklahoma, reported a decline.

Jun 1, 1931

By Hal J. Kelly

A number of problems that developed in processing the halloysitic clays of eastern Washington and northern Idaho were investigated by the Bureau of Mines. The deflocculating effect of tetra sodium pyrophosphate is compared with several other compounds, and on the basis of current theory, the advantage of sodium pyrophosphate as a deflocculating agent is explained. The adsorption of the sodium ion by clay in a clay"-water system was established by a radioactive tracer technique, and the deflocculating action of sodium pyro- phosphate was postulated. The effective dispersion of the halloysitic clays was limited by the occurrence of tightly bound aggregates of small, individual crystals. Disaggregation of the agglomerates was investigated by liquid extrusion and ball milling of dilute slurries and by extrusion of the clay in a plastic state. The greatest increase in the production of small particles was by high? pressure liquid extrusion.

Jan 1, 1963

By Alan J. Fejes

As part of its mine subsidence research program, the Bureau of Mines and the American Electric Power Co. cooperated on a study, conducted at the Price River Coal Co. No. 3 Mine, directed toward developing the capability to estimate the surface subsidence resulting from longwall mining in a geologic, topographic, and mining environment common to coalfields in the Western United States. Subsidence was monitored at the No. 3 Mine over two adjacent longwall panels. The subsidence study area was reduced when the two planned panels were reduced in length because of equipment failure and a mine fire. Subsidence was measured for 21 months. Subsidence continued for 6 months after mining had been completed. A maximum of 2.2 ft of subsidence occurred over the two longwall panels mined at an overburden depth ranging from 300 to 1,500 ft.

Jan 1, 1986

By Robert E. Barieau

In the design of plants to separate helium from natural gas, it is necessary to estimate the enthalpies of the various streams at various positions in the process. This Bureau of Mines report surveys the various methods that have been used to determine enthalpies and gives information on the organizations with such capabilities. The minimum information required for developing an enthalpy diagram is presented, and the relative merits of the various methods are discussed. It is concluded that methods that require no mass flow rate or energy measurements are to be preferred.

Jan 1, 1965

By K. D. Plants, J. H. Holden, L. F. Willmott

Pulverized high- volatile A bituminous coal was gasified with oxygen and superheated steam in a pressure - gasification pilot plant equipped for steampickup feeding . The pilot plant operated satisfactorily at relatively high steam- to - coal ratios , but steam- to - coal ratios could not be reduced much below 0.5 lb / lb without condensation of steam or softening of the coal . Carbon gasified , gas composition , and coal and oxygen requirements were essentially the same as for a pilot plant equipped with a fluidized coal feeder . Average results from the pilot plant equipped for steam- pickup feeding were coal requirement , 37.3 lb/M ( 1,000 ) scf of CO + H₂ produced ; oxygen requirement , 358 scf /M scf CO + H₂ produced ; and carbon gasified , 87.7 percent .

Jan 1, 1964

As shown in Table 9, consumption has risen steadily for the period November through April, reaching its highest level since June of 1974. Imports remained at a relatively high level in spite of decreased imports from Zaire and Belgium-Luxembourg. Award prices for cobalt sold by the General Services Administration on June 17, 1976 ranged from $5.058 to $5.41211 per pound of contained cobalt. The high bid was about $1 per pound above the current market price set by the major sales agent in the U.S. for cobalt on April 15, 1976. COPPER: Eight domestic producers on July 1 hiked refined copper prices by 4¢ to 74¢ per pound for cathode and to 74.625¢ for electrolytic wirebar. New York Commodity Exchange (COMEX) June pricing of prompt contracted copper averaged 70.6¢, with daily quotes registering between 67¢ and 72.5¢ per pound. In June, London Metal Exchange (LME) cash wirebar prices averaged 70.3¢, trading between a low of 65.5¢ and a high of 73.6¢. End of the month copper stocks totaled 108,758 short tons for the COMEX and 539,350 metric tons for the LME.

Jan 1, 1976

By Charles R. Harrison

The purpose of this study and resulting development of the training program, "Safety--Let's Make It Happen" was to determine the relation of concepts to the development of desired Health and Safety behavior. After extensive pre-contract study, it was hypothesized that improved acceptance and understanding of the Federal Coal Mine Health and Safety Act of 1969 could possibly contribute to the reduction of accidents. Second, in order for an individual to accept and understand the Act, he or she must have a working knowledge of its purposes and application. Third, acceptance and understanding of the Act, necessary to protect the individual from negligence, was imperative. Fourth, an actual operating company could provide the base in which to test these hypotheses in a meaningful manner and develop this type of training program. Six assumptions were agreed upon before embarking on this study and training program development. (1) In the cognitive process, a concept introduction into an individual's personality may result in a behavior quite different than if he or she had been exposed to a different concept.

Jan 1, 1977

By Michael Hamilton

Mineral resources have been identified at two properties in the Ten takes RARE II area (table 1). Commodities consist of copper and silver. The deposits, in the northwest part of the study area, are hydrothermal and associated with fissure veins that developed along northwest-striking faults within the Precambrian Purcell Lava. In addition to the identified resources, there is high potential for additional copper-silver resources at these properties and moderate potential for copper-silver-lead-zinc-bariun resources at five others (table 2) in the portion of the study area that is underlain by the Purcell. There is no evidence that significant mineralization occurred in strata above or below the Purcell.

Jan 1, 1983

By C. C. Hwang

The Bureau of Mines formulated a method for calculating the concentration of entrained dust from a dust deposit by a turbulent gas stream. In particular, a diffusion equation is used to calculate dust concentrations in a channel following an explosion. Dust leaving the channel walls was treated as originating from stationary or moving, and single or multiple material sources. Formulas and sample computations for various types of dust sources in circular and rectangular channels are given, based on experimental entrainment rates. The analysis predicts the dust concentration as a function of time and channel space. The results appear to agree with the physical characteristics of explosion-driven dust dispersion in a O.6-m-diameter, 50-m-long explosion tunnel. The analysis is also applied to simultaneous and consecutive dispersion of coal and rock dust from simulated coal mine surfaces (walls, floor, roof, and ribs).

Jan 1, 1974

By Tignor E. M.

The Brenneman oil field in Grant District, Hancock County, W. VA., was selected for study by Bureau of Mines engineers because it was typical of many of the smaller petroleum reservoirs in the Appalachian region. In 1906, E. W. Marland & Co. discovered the Brenneman field by drilling a well that readied the oil-bearing .Berea sandstone at a depth of 750 feet and initially produced 200 barrels of oil a day. Most of the oil-productive area (348 acres) of the field was developed in a comparatively short time, and the initial daily production rates of some of the wells were as high as 1,000 barrels of oil a day. Although the field was a prolific producer of oil for several years, it was abandoned in 1923 when the production rate was less than 1,000 barrels of oil a year and 705,000 barrels of oil had been produced. Secondary-recovery operations were started in the Brenneman field in 1927 after useable old wells had been repaired and unsatisfactory wells had been plugged; drilling of new wells was started in 1929. The peak of the redevelopment program was reached in 1942 when 92 oil-producing wells and 26 injection wells were in use; both air And mixtures of air and natural gas were used for injection purposes. It is estimated that approximately 357,000 barrels of oil, equivalent to 1,030 barrels per acre, 105 barrels per acre-foot, 8.5 percent of the total pore volume, or 11.9 percent of the original oil in place will be produced as a result of gas-injection secondary-recovery operations. Engineers of the Bureau of Mines Petroleum Field Office, Franklin, Pa., are studying secondary-recovery projects in the Appalachian region as a part, of the Bureau's secondary recovery research and are reporting these studies so that others: can profit by the experience gained from the operations. In common with most of the other Appalachian oil fields, there was no natural water drive in the Brenneman field. The estimated oil saturation in the Brenneman reservoir at the end of economic gas-injection operation indicates that additional oil might be recovered economically by water flooding and that a pilot flood would be warranted.

Jan 1, 1950

By W. L. Anderson

Standard tellurium analytical procedures were modified to obtain the greater sensitivity needed to support a survey of tellurium resources by the Bureau of Mines. Resulting volumetric and spectrophotometric methods for determining tellurium in all types of tellurium-containing materials are described. Sample decomposition and preliminary separations of interfering selenium, gold, and silver are the same in both procedures. The volumetric method is applicable to samples containing a minimum of 10 parts per million of tellurium, In this method the tellurium is reduced to elemental form, and the colloidal suspension is titrated with 0.01 normal iodine solution. The weight of sample for analysis, from 0.25 to 10 grams, should be selected so that the sample contains 0.1 to 5 milligrams of tellurium. To insure accuracy, duplicate samples should be run and the results averaged, particularly on samples of low tellurium content: The limit of determination is 0,001 percent tellurium, which is equivalent to 0.1 milligram of tellurium when using a 10-gram sample. The spectrophotometric method is particularly applicable to low-tenor materials containing from 0.5 to 50 parts per million of tellurium. Up to 10 gram samples are required for making accurate determinations in the low-concentration range. The sample used should contain between 5 and 100 micrograms of tellurium. The turbidity of a colloidal suspension of tellurium prepared from such a sample is determined in a spectrophotometer .t at a. wave-length of 440 millimicrons, and this value is compared with those of standard samples containing known amounts of tellurium.

Jan 1, 1963

By Yael Miron

The presence of pyrite (FeS2) in coal can cause or contribute to several problems for the coal mining industry. These problems, which include spontaneous combustion, roof falls, floor heave, and accidental explosions in coal surface mining when ammonium nitrate fuel oil (ANFO) explosives are used, result from pyrite oxidation. Pyrite oxidizes exothermically in the presence of air and moisture to form a large variety of products, including hydrated ferrous and ferric sulfates, and sulfuric acid. Some of the products are reactive chemicals and strong oxidants. The volume of many of these oxidation products exceeds the original volume of the pyrite; as a result, the adjacent coal disintegrates and its surface increases, rendering it more susceptible to oxidation. The heat from pyrite oxidation raises the temperature of the adjacent coal, accelerating the oxidation and self-heating rates of the coal. These combined chemical, physical, and thermal effects are the cause of the aforementioned problems. When ANFO is used in surface coal mines and contacts ferrous sulfate, a highly exothermic reaction ensiles. Additional hazards are fires or explosions caused by the frictional ignition of methane when the pyrite in the coal is struck by a cutting bit during mining.

Jan 1, 1994

By J. H. East

"INTRODUCTION .Very little information regarding coal mining in Spain has been published in the American technical press, and few people realize the extent of this industry or the conditions under which coal is mined. The information in this publication was collected in 1945 and consists of personal observations in Spain, statistics, and other data of a, general nature obtained from official sources.Spain produces bituminous coal, lignite and anthracite, but the total tonnage mined is less than the national requirements. Before the war, an appreciable tonnages coal was imported from Great Britain under the Anglo-Spanish treaty, which rebated import duties and effectually prevented competition from any other foreign source. The war stopped the major part of the important of British coal and caused rapid expansion of the domestic sources, but this was not sufficient to supply the industrial demand. Coal that formerly was not acceptable to industry because of quality is now mined and marketed. The Government, allocates the better-grade bituininous coal to the various industries in accordance with the national importance of the work in which they are engaged; for example, the railroads are allotted 100 percent of their requirements, but cement companies can obtain only 25 percent.The Government offered to inducements to increase the production of coal of any class, but the larger part of the increased tonnage obtained was in inferior grades; as a result, the lignite production was taxed, while a bonus was paid for bituminous-coal production in excess of the 1942 tonnage.The anthracite and bituminous-coal areas were severely damaged during the Civil War and many experienced miners migrated to the lignite mines in eastern Spain. This has resulted in an acute shortage, particularly the Province of Oviedo where the most important bituminous-coal deposits are located."

Jan 1, 1947

By R. V. Ramani, R. Bhaskar

"The control of respirable dust in mines has been given paramount importance due to the health and safety implications associated with fine dust. The understanding of the temporal and spatial behavior of dust has been recognized as essential for increasing the efficiencies of the existing control techniques and for developing new control strategies. Mining-related studies in this area are, in general, limited. They are also mostly experimental. Some mathematical and computer analyses have been attempted. In this paper, first a review of the mathematical studies performed in the last three decades in this area is presented. Second, a mathematical model for analyzing dust flow in mines is proposed. The model takes into account a number of factors affecting dust transport. It incorporates varying dust generation source strengths and dispersion, deposition, and coagulation of dust in mine airways. Finally, application areas for the model are discussed. A computer program based on the mathematical model has been developed. The program will output the dust concentration in the mine atmosphere as a function of time and distance from the source. The amount of dust deposited on the sides, roof, and floor of the airway is also determined.IntroductionAn airborne dust cloud is a complex system containing particles of varied size, density, shape and state of aggregation. The behavior of the particles is dependent on a number of complex physical mechanisms, often opposing in nature. The net interaction results in the ambient concentration. This size dependent behavior of particles contrasts with that of gases, an area quite widely studied.The term aerosol is used to describe clouds of microscopic and submicroscopic particles in air such as chemical smoke or particulate matter released from smoke stacks. An aerosol system can be regarded as an arbitrary element of volume filled with gas and suspended particles of possible highly variable physiochemical nature. The parameters that are used to describe an aerosol system include concentration, mass average velocity and particle mass and radius. In characterizing such systems, several assumptions are made. Among these is the assumption that particles are smooth, inert and rigid spheres. Again, for example, when the particles are in transport, the possibility of collision exists. As a result of the collision, the particles may coalesce to form larger particles. The probability of sticking is considered a known quantity (lady, 1970). In this paper, the application of the principles used in aerosol systems is explored for the study of the transport and deposition of fine coal dust in underground mines."

Jun 1, 1988

By Raymond B. Ladoo

"The talc and soapstone deposits of Vermont have been worked more or less continuously for nearly 100 years, but all of the early efforts seem to have been directed toward the production of slabs for foot warmer, and other similar uses. Altho soapstone of good quality occurs at several places, much of the material first utilized was really talc and was not massive enough to be cut successfully. The grinding of talc in Vermont seems to have commenced in about 1902 and has shown continuous growth since that time. Statistics compiled by the Geological Survey in Mineral Resources of the ,United States show that the production of talc in Vermont has increased, from 8,978 short tons valued at $65,525 in 1905 to 93,960 short tons valued at $625,150 in 1917. Until 1917, New York was the leading producer in both tonnage and value with Vermont second, but in 1917, Vermont took the lead in tonnage produced, although not in value, with a production of over 47% of the total tonnage produced in the United States and over 35% of the world's pro-duction. This increase in production will probably be continued, though possibly at decreased rate, for the reserves of talc In Vermont are large.Active talc mines and mills in Vermont are found in four districts: Chester, Windsor County; Rochester, Windsor County; Waterbury, Washington County; and Johnson, Lamoille County, These mines and mills are distributed as shown in the following table:While there are a great many other known deposits of talc and soapstone in Vermont, some of which have been worked, those listed above are the only ones which have survived and are producing on a commercial basis. The closing down of many mines and quarries, for example, those at Perkinsville, Stockbridge, Reading, Cavendish, and Athens, has been attributed to several causes. Of these causes the most important seem to be exhaustion of the deposit, poor grade, long haul to the railroad, poor management due to lack of knowledge of mining methods and failure to consider talc mining strictly as a business proposition. The companies which are now operating with greatest apparent success are those which have realized the present and future possibilities of their industry, and have invested sufficient capital in both equipment and personnel to establish their companies on a firm business basis."

Sep 1, 1919

By L. B. Berger

In this investigation, the ampoule type of carbon-monoxide (CO) detector which is manufactured under license of U. S. Patent 1,644,014 (October 4, 1927) was tested for sensitivity and reliability. This detector was devised primarily for examining the air of manholes and sewers for possible dangerous contamination with CO before workman enter those places, but dine to the simplicity of the device it may have a more general usage for examination of atmospheres which are known or suspected to be contaminated with CO. Some of the suggested uses are the examination of the air in garages, tunnels, mines, around blast furnaces, gas plants, and in the home.

Jan 1, 1930

By D. J. Singleton

Erosion corrosion of 12 alloys in phosphoric acid waste water was studied by the Bureau of Mines. Tests were conducted on oblate spheroids or cylindrical specimens in 12-and 60-cm-diam ball mills by grinding phosphate rock in gypsum pond water with a starting pH of 1.6. For comparison, tests were conducted while grinding phosphate rock in plain water. Static corrosion tests in gypsum pond water also were conducted. For all alloys, the wear by erosion-corrosion (milling with gypsum pond water) was greater than the sum of erosion (milling with water) plus static corrosion. Erosion-corrosion wear was about 1,500 to 3,000 mpy for the alloyed white cast irons, 1,000 to 1,400 mpy for commercial steel ball material and type 316 stainless steel, and 600 to 900 mpy for nickel-base alloys and a high-manganese, nitrided stainless steel. Alloy costs per unit of phosphate rock 'processed favor a low-alloy, high-carbon steel or a high-manganese, nitrided stainless steel.

Jan 1, 1985

By John M. Gomes

The Bureau of Mines investigated two techniques for removing CaO from scheelite (CaW04) prior to electrolysis. In the first technique, a crude tungstic oxide (WO3) containing 0.15-percent lime (CaO) was prepared by digesting scheelite concentrates in hot hydrochloric acid. This oxide was used as cell feed to produce tungsten of 99.9-percent purity. The second technique used a high-temperature, two-phase separation, resulting in extraction of 99 percent of the WO3 in the halide-tungstate phase, while 90 percent of the CaO was retained in the silicate phase. Tungsten of 99.9-percent purity was deposited from the halide-tungstate melt after B203 and NaPO3 were added to form an electrolyte. The two methods were compared with a previously developed technique of depositing tungsten from scheelite concentrate fed directly to the electrolytic cell.

Jan 1, 1971