Search Documents

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the non-condensable gases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of Gases produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills. The study required a complete extraction of all the hydrogen sulphide from the gas stream after it left the water-cooled distillate condensers and before the gas stream entered the charcoal absorber for removing the light naphtha. In devising the method it was necessary to take into account a constant variation of velocity, pressure, and percentage of sulphide in the total gas stream coming from the still. Ordinarily, the quantitative determination of hydrogen sulphide in gas is made by analyzing small samples taken at regular intervals. This estimation can be accomplished by use of the Bunts gas burette as modified by Tutriler, or by a similar method. In the industries where the flow of gas is constant and of uniform composition, this practice is sufficiently accurate for plant control. For experimental work where many variables have to be taken into consideration, as in the case at band; these methods are not applicable.

Jan 1, 1931

By A. F. Cohen

When location guidelines are followed in choosing sites for fixed point velocity transducers for use in underground coal mine monitoring, mine air turbulence intensities <11% are generally expected at those sites. The objective of this Bureau of Mines investigation to determine the effect of turbulence intensities <11% on vortex shedding sensors and transducers. Measurements were made at velocity levels of interest for underground coal mine monitoring use (?200, ?500, ?1,000, ?1,500 ft/min). The effect of grid-produced turbulence intensities (2% to ?14%) on the output of vortex-shedding air-velocity transducers was less than ±10%.

Jan 1, 1985

By Deborah A. Kramer

An economic and technical evaluation of a proposed process to recover alumina by leaching calcined kaolinitic clay with sulfurous acid is presented in this Bureau of Mines report. After the insoluble portion of the clay has been removed by leaching, monobasic aluminum sulfite is precipitated from the pregnant leach solution by partial hydrothermal decomposition. Further heating completes the decomposition to an impure alumina hydrate. This intermediate is purified in a modified Bayer process, which includes dissolving the alumina hydrate in a caustic solution at high temperature and pressure, then decreasing the temperature and pressure to precipitate alumina trihydrate. Calcining the trihydrate produces the alumina product. A cost estimate was prepared for a plant producing 1,000 tons of alumina per day, 350 d/yr. The estimated operating cost is approximately $475 per ton of alumina. This is substantially higher than a comparable estimated operating cost for the Bayer process of $250 per ton of alumina. The proposed process does not appear economically attractive, even as a method to modify a current Bayer processing plant to use a kaolinitic clay feed. High capital costs and high energy requirements make the process prohibitively expensive.

Jan 1, 1983

By S. H. Katz, J. J. Bloomfield

In studies of mine and tunnel ventilation conducted by engineers of the Bureau of Mines , various smokes are used to determine flow of air , direction of the currents , and the rate of mixing . The instrument for generating streams of sulphur trioxide (SO ) smoke , shown in the drawing herewith, has been found helpful , convenient and practicable for such purposes ; it is also especially useful in some places where fire for generating smokes is not permissible . The apparatus consists simply of a glass tube containing fuming sulphuric acid on granular pumice stone , attached to a rubber syringe bulb . When a squeeze of the bulb blows air through the tube , a stream of dense white smoke evolves, which follows and makes visible the air currents . The tubes after preparation are hermetically sealed to prevent deterioration . When ready for use , they are easily broken open at a file scratch for the purpose on both tips , and inserted into a rubber nipple at the bulb . Sometimes it is of advantage to attach them to a longer rubber tube leading to the bulb . Tubes of the size shown (about 1/2 inch outside diameter by 5 inches long) are usually sufficient for the needs of a day . Thereafter they cease to fume because the acid absorbs moisture from the air and looses its effectiveness . Smaller sizes of tubes and larger have been made , but the size shown has proved most practicable . Immediately after a person has finished using a tube it should be buried or disposed of in a place where it will not be touched by shoes or clothing, or come in contact with wooden floors , furniture , or metals , because the acid , which will eventually leak from the tubes , is highly corrosive . -- Reports of Investigations , Department of the Interior , Bureau of Mines .

Jul 1, 1923

By N. N. Moebs

The atmosphere in part of an air-sealed coal mine was monitored continuously through a drill hole for oxygen content to determine the effectiveness of sealing a mine against the entrance of air and the major force that caused the phenomenon of mine breathing through the overburden. The differential pressure across the seal and the barometric pressure on the outside also were recorded. A general correlation, obtained between the oxygen level, differential pressure, and barometric pressure, indicates that changes in air pressure are the cause for periodic replenishment of the oxygen in the mine. Mine effluent quality was determined by conditions in many sections of the mine and could not be related to the oxygen level at the drill hole.

Jan 1, 1972

By W. E. Miller, G. S. Scott, G. W. Jones

"An important activity of the Bureau of Mines is the promotion of safety in mining and industry. In connection with these activities, the Bureau determines the explosion hazards of combustible gases, liquids, and solids and investigates means by which explosions may be eliminated or reduced in violence.The limits of inflammability and ignition temperature of combustible gases, vapors, and solids are of practical importance because such materials can be manufactured, transported, and used with greater safety, provided the range of concentrations and temperatures that cause explosions are known.Many organic compounds, which until a few year ago were merely laboratory curiosities, are now being manufactured in large quantities owing to the national emergency, particularly those chemicals entering into the manufacture of synthetic rubber, a product that is playing a major role in the Government program of national defense. This re Jolt gives results relative to the limits of inflammability of styrene and its ignition temperature in air and oxygen. This combustible liquid is now used extensively in the manufacture of synthetic rubber."

Mar 1, 1942

By Edward D. Thimons

Several types of inflatable stoppings, developed under Bureau of Mines contract for use as mine air barriers during underground production, have been tested by the Bureau. All of the stoppings tested showed significant internal leakage initially but, in all but one stopping, the leaks were sealed with limited effort The stoppings were tested underground in two western noncoal mines under production conditions. The results from the Colorado molybdenum mine showed the stoppings to be generally unsatisfactory for daily mine usage if they are deployed near blasting areas or in locations where near-perfect air seals are required. They were very susceptible to blast damage and seldom were better than 90 percent efficient as air barriers. However, stoppings tested in the New Mexico uranium mine were located substantially distant from any blasting. Because slight leakage past the stoppings was acceptable, they proved very satisfactory in that application.

Jan 1, 1976

By P. R. Moyer

"INTRODUCTION The Federal Explosives Act (55 Stat., 863), as amended, was passed by Congress on December 26, 1941, and became effective immediately; it amended the Act of October 6, 1917 (4o Stat., 385). The purpose of the Act was to regulate the manufacture, storage, use, and possession of explosives in order to prevent sabotage and to assure that explosives and ingredients would not fall into unauthorized hands. Under the provisions of the Act, the Director of the Bureau of Mines was authorized to administer its provisions under the supervisions of the Secretary of the Interior.EXPLOSIVES-CONTROL DIVISIONTo administer the Act, necessary personnel were employed in accordance with the appropriation made from a special presidential fund and later by Congress, and the Explosives Control Division was organized as a part of the Health and Safety Branch of the Bureau of Mines constituting the fourth division of that branch. A central office was established in Washington, D. C., and field offices were designated largely at the offices of the Health and Safety Branch throughout the country, and 50 explosives investigators were employed and assigned to work from these offices under the direction of the district engineers of the eight districts into which the United States is divided by the Health and Safety Branch. The territory assigned to each investigator was based on the approximate amount of explosives stored in that area; however, smaller territories were assigned to investigators stationed near the Pacific coast, which was indicated as critical by the armed forces."

Mar 1, 1947

By O. C. Blade

This report on the properties of motor fuels sold through service stations in the United States was made in accordance with a cooperative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. By agreement with the American Petroleum Institute, identification of the items is confidential. It presents analytical data for 3,924 samples, representing the products of 116 companies. The samples were collected during June, July, and August, 1954. As in previous surveys, the gasolines covered by this survey include those from both large and small suppliers, The data were obtain& by laboratories of various refiners, motor manufacturers, and chemical companies and submitted to the Bureau of Mines for compilation, A list of the National Motor-Gasoline Survey reports published during the past 10 years is given on page 5.

Jan 1, 1955

By Eric S. Weiss

The National Institute for Occupational Safety and Health (NIOSH) and the Mine Safety and Health Administration (MSHA) conducted joint research to evaluate explosion blast effects on typical U.S. mine ventilation stoppings in the NIOSH Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM). An innovative Australian-designed brattice stop-ping was also evaluated. After mine explosion accidents, MSHA conducts investigations to determine the cause(s) as a means to prevent future occurrences. As part of these postexplosion investigations, the condition of underground stoppings, including the debris from damaged stoppings, is documented as evidence of the approximate strength and the direction of the explosion forces. The LLEM data showed that a typical dry-stacked and coated solid-concrete-block stopping survived a total explosion pressure of ~6.7 psi (~46 kPa) and was destroyed at a total explosion pressure of ~7.6 psi (~52 kPa). In comparison, a typical dry-stacked and coated hollow-core concrete block stopping survived a total explosion pressure of ~3.4?4.3 psi (~23?30 kPa) and was destroyed at a total explosion pressure of ~3.6?5.2 psi (~25?36 kPa), depending on the length of the pressure pulse and the value of the pressure-time integral. A typical steel panel stopping design survived a total explosion pressure of 0.8 psi (5.5 kPa) and failed at a total explosion pressure of 1.3 psi (9 kPa). The LLEM data also showed that an obstacle blocking the path of a pressure wave resulted in a higher reflected pressure at the obstacle. An 8-in (20-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~26 psi (~180 kPa); this stopping was not tested to failure. A 6-in (15-cm) thick wet-laid solid-concrete-block stopping coated on one side survived a total explosion pressure of ~14 psi (~97 kPa) and was destroyed at a total explosion pressure of ~25 psi (~172 kPa). An innovative Australian woven cloth stopping survived an explosion pressure of 4.0 psi (27 kPa) and was destroyed at an explosion pressure of ~6.1 psi (~42 kPa). These results will help investigators determine the approximate explosion forces that destroy or damage stoppings during actual coal mine explosions.

Jan 1, 2008

By Guthrie. R. K., H. B. Hill

"INTRODUCTION During the early 1920's world-wide attention was attracted to a group of oil fields (Mexia, Wortham, Currie, Richard, and Powell) later known as Mexia-Powell fault-line fields in Limestone, Freestonne, and Navarro Counties, Tex. Enormous yields of high-gravity oil from the wells in these fields resulted in drilling campaigns that quickly surpassed all previous records for rapid, intensive development of productive areas. The discovery of oil in the Mexia filed in September 1921 was followed quickly by the finding of oil in the Currie field in October. In January 1923 oil was discovered in the Powell field; in February 1924 the Richland field, midway between Currie and Powell fields, was brought in; and in November 1924 oil was discovered in the Wortham field, situated between Mexia and Currie fields. Each of the fileds was developed rapidly: wells were spaced closely and had high initial production; production peaks were reached early in the producing lives of the fields; subsequent decline was rapid, and there was early and rapid encroachment of edge water.In 1927 Bureau of Mines engineers, in their investigations a engineering conditions in oil,completed a preliminary study and published a mimeographed report 4/ on underground conditions in the Wortham field, and in 1928 they reported on production and development problems in the Powell Field. 5/ field."

Aug 1, 1943

By N. A. Eilertsen

Among the numerous Low-grade manganese deposits in eastern Aroostook County, Maine, the Dudley deposit near Mapleton in the northern district is one of the few known to contain an appreciable tonnage averaging above 10 percent manganese. The ore body, consisting of stratified manganiferous hematitic shale, is over 5,000 feet long and ranges in width from 30 to 175 feet. The deposit was extensively explored during 1942-44 by the Manganese Ore Co., a subsidiary of M. A. Hanna Co. of Cleveland, Ohio. Data obtained from this work were made available to the State and Federal Geological Surveys for estimating ore reserves. An estimate by the Maine Geological Survey, using a 10-percent manganese cutoff and to a depth of 200 feet, shows 609,000 long tons of manganese metal in material averaging 12.6 percent manganese. By lowering the cutoff limit to 5 percent manganese, the estimate was increased to 919,000 long tons of metallic manga¬nese in material averaging, 10.4 percent manganese,

Jan 1, 1957

By Walter D. Holland

This document is one of a series of instruction guides developed to help instructors present health and safety training courses to workers in the metal and nonmetal mining industry. This course is intended to provide above ground metal and nonmetal mining employees with training which will assist them in performing their work safely and healthfully. A document entitled, "Airborne Contaminants in Above Ground Metal and Nonmetal Mining and Processing Work Areas," is used as a manual for the students during the course. The unique features of the teaching guide are thumb rules for recognizing hazardous situations, candidate contamin¬ants for each work area and descriptions of control devices and work procedures.

Jan 1, 1977

By Peter K. Mathison

The U.S. Bureau of Mines has developed a hydrologic monitoring system for in situ leaching operations. This system records and displays flow and pressure information from sensors located in leachant injection and recovery wells. Continuous monitoring of hydrologic conditions is important during leaching operations because hydrologic factors such as aquifer permeability, solution injection rates, injection pressure, and solution recovery rates interact and change over time. This hydrologic monitoring system has been tested in an underground setting at the Cyprus Casa Grande copper mine. The system consists of hardware and computer software components and includes two Bureau-developed software applications. This publication describes the implementation of the hydrologic monitoring system and the software developed at the Bureau in support of in situ leaching research.

Jan 1, 1994

By W. E. Miller, Kennedy. R. E., G. W. Jones

"INTRODUCTION Ethyl mercaptan (CH3,CH2SH), a combustible organic liquid of the thioalcohol type, is employed at an odorant in many types of fuel gases and dangerous atmospheres, which in themselves are devoid of characteristic odors, to give warring against leakage of such gases or atmospheres into places where they might constitute health or explosion hazards.Ethyl mercaptan has a penetrating disagreeable odor resembling that of onions, garlic, hydrogen sulfide, or rotting cabbage, that exceedingly low concentrations of it can be detected. The of odorants as a beans of detecting leakage of gases and atmospheres has been investigated extensively by chemists and engineers of the Bureau of Mines, and numerous reports as to its value have been published."

Jun 1, 1942

By W. S. Landers

This report presents a study by the Federal Bureau of Mines of technical factors related to the production of special carbon and tar from selected Wyoming coals. Certain Wyoming high-volatile bituminous and subbituminous coals were processed in bench-scale apparatus to determine potential carbonization yields and in pilot plant retorts to produce sufficient char and tar for testing. These tests have shown that a critical selection of coal is necessary when the coal is processed for a specialized carbon. Generally high yields of tar are obtained from low-temperature carbonization of Wyoming high-volatile bituminous and subbituminous coals, and the yield of tar usually increases with increase in rank within this range of coals. The production and evaluation of industrial carbons from Wyoming coals by using pilot plant and bench-scale techniques is part of the continuous program of upgrading western coals. It has been found that: 1. Most Wyoming coals are nonagglomerating and may be carbonized in fluidized systems. Chars produced in pilot plant retorts at low temperatures contain about 17 to 23 pct, residual volatile matter and are easily ignited. These chars appear suitable as power plant fuel. The tar-plus-light-oil yields range from 14 to 40 gal./ton of raw coal processed. 2. Wyoming high-volatile coals produce a slightly smaller and somewhat weaker coke than currently mined Western United States high-volatile coals used commercially as blending stock in metallurgical coke production.

Jan 1, 1961

By M. C. Irani

The Bureau of Mines, in cooperation with the Mine Safety Appliances Co., has developed a continuous-recording methanometer utilizing a catalytic combustion detector. The methanometer, which is presently operating at 22 exhaust fans at 14 mines in the Eastern coalfields, is reliable and simple to install, operate, and maintain. The instrument and the details of its installation and calibration are described. Analytical data obtained by infrared spectrophotometer and gas chromatograph are presented to substantiate its re liability.

Jan 1, 1974

By W. I. Nelson

This paper describing the mining practices at the Engels mine is one of a series being prepared by the United States Bureau of Mines on mining practices, methods, and costs in the various mining districts of the United States. The Engels Copper Mining Co. operates two mines about 3 miles apart in Plumas County. Calif. Both mines send ore to the same mill, and the methods of the larger, or Engels mine, are described in this paper. Between 800 and 1,000 tons of 1-3/4 to 2-1/2 per cent copper ore are mined daily from this mine by a shrinkage method. Connection is made with the Western Pacific Railroad at Paxton by the Indian Valley Railroad, which is 22 miles long and operates a daily mixed train to the mine.

Jan 1, 1930

By H. C. Fuller, J. H. Jacobs

"Manganese ore from Metals Reserve stock piles at Deming, N. Mex., Cushman, Ark., and Philipsburg, Mont., were processed in the Bureau of Mines pilot plant at Boulder City, Nev., to determine their suitability for the production of electrolytic manganese. Manganese was produced successfully from all of the ores.The ores, crushed and ground to minus 33-mesh, were roasted in a Skinner furnace to reduce the manganese and were then leached with spent electrolyte, from the cells, containing sulfuric acid. Acid-leach extractions of 96 percent on Deming, 89 percent on Cushman, and 97.5 percent on Philipsburg ores were obtained. Neutralization of leaches with ammonia results in the highest manganese extraction; but Cushman and Deming leaches could not be neutralized with ammonia, because the amount required was more than enough to maintain the proper ammonium sulfate concentration. A combination of ammonia and calcine was used. However, ammonia was satisfactory for neutralization of Philipsburg leaches. Sulfuric acid needed for make-up was as follows: Deming, 0.380 pound per pound of manganese extracted when neutralized with ammonia and calcine; Cashman, 0.402 pound per pound of manganese extracted when neutralized with ammonia and calcine; Philipsburg, 0.594 round per pound of manganese extracted when neutralized with ammonia alone.All of the leach slurries settled well enough to be separated and washed in countercurrent thickeners.Impurities were precipitated with hydrogen sulfide and removed by filtration. Cushman ore solution contained only- small amounts of impurities and required 0.055 gram of hydrogen sulfide per liter of solution for purification. Deming and Philipsburg solutions contained large amounts of zinc and required 0.55 and 0.65 gram of hydrogen sulfide per liter of solution, respectively.Electrodeposition was satisfactory on all three ores and current efficiencies of 62 to 66 were obtained.A process for the production of electrolytic manganese has been developed by the Bureau of Mines, first on a laboratory scale4/ and then on a semicommercial pilot-plant scale.5/ At first the- pilot plant operated on ore from the Three Kids mine near Las Vegas, Nev., to determine the practical features of the process on ore of this type. Since completing the work on this ore, the pilot plant has been used for processing other domestic ores to obtain engineering data and other economic information regarding the amenability of such ores to the process."

Sep 1, 1946

By E. Morrice

The metallurgical laboratory data developed in this study indicate an improved electrowinning process for producing higher purity cerium ingot. A typical sample of the Reno electrocerium contains 99.9 weight-percent cerium and the following impurities: Total other rare-earth elements, less than 0.04 percent; iron not detected; silicon and aluminum, less than 0.02 percent each; calcium plus magnesium, less than 0.01 percent; carbon, 0.01 percent; oxygen, 0.002 percent; hydrogen, 0.0003 percent; and nitrogen, 0.0015 percent.

Jan 1, 1960