Search Documents

By R. D. Leitch

Tests have recently been conducted by the Bureau of wines on the ignition hazard of exposing heated filaments of electric mine lam bulbs in an explosive mixture of methane and air. This investigation was undertaken in order to settle a question that had arisen in connection with the safety of miners? electric lamps. For several years, in view of former studies made by the Bureau and reported in Bulletin 524, the fact that the heated filaments of even low voltage, lour candlepower bulbs constitute a danger was generally accepted by the Bureau's engineers. These early tests, as well as subsequent tests, were conducted with Pittsburgh natural was as the testing medium.

Jan 1, 1925

By Henry W. Busch

Determination of the aldehyde content of Diesel-engine exhaust gas has proved rather cumbersome and unsatisfactory when carried out in its entirety in field investigations; therefore, studies were conducted with a view to developing methods by which samples might be collected in the field and trans-ported to the laboratory for analysis. Experience also indicated that aldehyde samples collected in water solution and then transported to the laboratory sometimes underwent serious changes in composition if several days elapsed between sampling and analysis. Polymerization of the aldehydes, which takes place readily in dilute aqueous solutions, may have been the cause of such changes. Because of these difficulties, experiments were conducted to find a suitable stabilizer or preservative for dilute aqueous solutions of the aldehydes that occur in Diesel-engine exhaust gas, so that in field studies a known volume of gaseous sample might be collected and brought into contact with water, and the resulting solution of aldehydes analyzed in the laboratory at some later time with reasonable certainty that the results would represent the composition of the original sample,

Jan 1, 1949

By R. K. Koch

The vapor pressures of liquid molybdenum and liquid zirconium were determined by the Langmuir free-evaporation method. An electron-beam furnace with a water-cooled copper crucible was used for melting. Temperature was measured with a two-color ratio pyrometer. The vapor-pressure data led to the following equations: [log p (atm) = 5.429 - 28,380 T for liquid molybdenum in the range 2,890° to 2,990° K, and log p (atm) = 6.521 - 30,940 T for liquid zirconium in the range 2,229° to 2,795° K.] Third-law evaluations of each data set gave mean heats of sublimation (298.15° K) of 157.6 ± 1.8 kcal/mole and 148.4 ± 2.4 kcal/mole for molybdenum and zirconium, respectively, where the uncertainties are two standard devia¬tions. Second-law standard heats of sublimation determined from sigma plots and tabulated enthalpies were 143.5 ± 2.7 kcal/mole and 149.2 ± 3.8 kcal/mole for molybdenum and zirconium, respectively. The better agreement in heats of sublimation for zirconium is attributed to the 566° K temperature range studied which permitted a more accurate definition of the vapor pressure curve than could be obtained from the 100° K span for molybdenum. This supposition was verified by making a sigma-prime plot which utilized solid vapor pressure data for molybdenum to extend the evaluation range by 800° K. This gave a standard heat of sublimation of 155.2 ± 1.6 kcal/mole which is in good agree¬ment with the third-law value. The plot also gave a standard entropy of sublimation (298.15° K) of 35.73 ± 0.48 eu.

Jan 1, 1968

By R. F. Abernethy

A modified Unterzaucher method was applied to the direct determination of oxygen in coal. Coal samples were pyrolyzed in a nitrogen atmosphere, and the gaseous oxygen compounds liberated were converted to carbon monoxide by a platinized-carbon catalyst at 9000 C. After passing over heated copper and through a tube containing soda-asbestos and magnesium perchlorate, the purified carbon monoxide was oxidized to carbon dioxide by iodine pentoxide--liberating an equivalent amount of iodine. The iodine was titrated with 0.02 ~ sodium thiosulfate; in a few tests the weight of carbon dioxide produced was determined. Direct oxygen determinations of coal included organic oxygen from the coal substance, plus a small quantity of inorganic oxygen derived principally from carbonate minerals and from combined water of silicates in the mineral matter. The influence of mineral matter on the direct oxygen determination was investigated by testing (1) untreated coal, (2) demineralized coal from which most of the mineral matter except pyrite was removed by treatment with hydrofluoric and hydrochloric acids, and (3) coal samples treated with dilute hydrochloric acid.

Jan 1, 1966

By S. J. Aresco

The Bureau of Mines has been active in promoting the purchase of coal for Government use under specifications that define the requirements in terms of heating value of the coal, expressed in British thermal units, and the composition as shown by proximate analyses. To these, when required, are added the ash-softening temperature, the free-swelling index, and the Hardgrove grindability index. Under most of these specification contracts the bidders guarantee the quality of the coal, and that guaranteed by the successful bidder becomes the standard of his contract. The deliveries are sampled in accordance with instructions4/ issued by the Bureau of Mines, the samples are analyzed in the Bureau laboratory to determine whether the coal is of the quality guaranteed by the contractor and, if it is not, a price adjustment is made. Analyses of the delivered coal and tipple samples (samples collected at mine tipples as coal is being loaded into railroad cars or trucks) provide valuable data for use in evaluating future bids. In addition, the continuous sampling of coal as delivered is a check on the practical results obtained in burning the coal.

Jan 1, 1957

Electric power curtailments resulting from the coal strike, required Noranda Aluminum, Inc. to shut down its 140,000 ton-per-year (tpy) primary aluminum smelter at New Madrid, Mo., and layoff 308 workers. Other primary aluminum production facilities affected by the coal strike included the Aluminum Company of America plant at Evansville, Ind. which shut down half of one potline; the Eastalco Aluminum Co., smelter at Frederick, Md., which cut production by 7 percent; and the National-Southwire Aluminum Co. plant at Hawesville, Ky. which cut production by 6 percent. Alumax, Inc. announced that construction had started on a 91,000 tpy potline at the Eastalco primary aluminum smelter. The new potline will be owned 65 percent by Alumax and 35 percent by Mitsui & Co. Ltd. Howmet Aluminum Corp., which currently owns 50 percent of the existing 176,000 tpy facility, has the option of becoming a 50 percent owner of the third potline in 1982. Construction of the new line was scheduled to be completed in 1980.

Jan 1, 1978

By W. M. McKewan

This U.S. Bureau of Mines report discusses wire ropes used for hoisting in U.S. mines. The in-formation presented was extracted from a large body of data compiled by the U.S. Mine Safety and Health Administration (MSHA) using a data base management system (DMS). Further, these extracted data were then manipulated to provide tables of data that show the types and amount of wire rope used for hoisting. This report describes the different types of wire ropes and how a DMS can be used to manipulate MSHA's wire rope inventory data. The data indicate that more 1-1/4-in-diam ropes, 6x27 construction ropes, and right lang lay ropes are used in U.S. mines than ropes of any other diameter, construction, or lay type.

Jan 1, 1991

By John P. Conway

This Bureau of Mines investigation was undertaken to determine the feasibility of lock-bolt support in Tertiary-gravel material. Pull tests were performed on five types of rock-bolt anchors to determine their optimum anchorage capacity. Four of these anchors are commercially available; the fifth, an explosive-anchor bolt, was developed by the Bureau of Mines. To increase anchorage capacity, epoxy grout was used with several of the commercial types of bolt. Tests showed that sufficient anchorage could be obtained by employing epoxy-resin grout with the commercially available wedge bolt, or by using the explosive-anchor bolt. Also estimated are bolt spacing and cost of a rock-bolt support system.

Jan 1, 1971

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By George T. Motock

The author prepared the following report as the result of a trip to Germany in the summer of 1945 for the Technical Industrial Intelligence Commitee Subcommittee on Metals and Minerals. The purpose of this committee, which functions under the Joint Intelligence Committee of the Joint Chiefs of Staff of the United States Armed Forces and of which the Bureau of Mines

Jan 1, 1946

By Rollie P. Dobyns

The K.M.A. reservoir was discovered to be oil bearing at a depth of 3,719 feet on March 11, 1931. Extensive development, however, was not begun immediately, because the discovery well had a low initial daily oil production, and market conditions for oil were unfavorable. Development of the field progressed slowly for the next 6.5 years. In the latter part of 1937, a wildcat well approximately 2 miles southwest of the discovery well was drilled on a magnetometer high and completed with an initial flowing production of 2,018 barrels of 430 A.P.I.-gravity oil in 12 hours. Rapid development of the southwestern part of the K.M.A. field was begun immediately and continued until over 700 wells were drilled and approximately 12,500 acres proved oil productive. Because of the large size of the entire K.M.A. field, this report is limited in scope to the southwestern part only, and the discussion that follows pertains to this area only. The closing date for production statistics is August 1, 1949. The K.M.A.? structure is a complex anticline having a maximum closure of 250 feet, and the K.M.A. formation is composed of sediments that grade from limestone through sandy lime and limy sand to sandstone with thin streaks of shale. Two "distinct members of the K.M.A. formation, zone I and zone II, are oil productive. Core analyses indicate the average porosity to be 16.5 percent for zone I and 16.1 percent for zone II. A relationship was established from core data, which showed the correlative permeabilities to be 42.1 millidarcys for zone I and 39.5 millidarcys for zone II, whereas the arithmetical averages of the permeabilities were 84 millidarcys for zone I and 216 millidarcys for zone II. Connate-water saturations were 17.5 percent for zone I and 20.0 percent for zone II. The porosity-saturation method, using a thickness-correction factor, was employed to calculate the volume of 168.1 million barrels of stock-tank oil initially in place in the reservoir. Analyses of the reservoir oil indicate that, although the initial reservoir pressure was 1,750 p.s.i., the original reservoir oil was saturated to only 1,300 p.s.i., at which pressure 1 barrel of stock-tank oil contained 525 cubic feet of ea~ in solution.

Jan 1, 1952

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By Manuel Gomez

The Bureau of Mines used data from 31 core samples to develop prediction equations for evaluating chemical and carbonization properties of six seam units in a lignite deposit approximately 2 miles wide and 8 miles long in the Wilcox Formation of central Texas. Statistical response surfaces, based on core analyses, were computed for 14 parameters indicative of lignite quality. These computed surfaces, and their mathematical equations, can be used to predict values of the selected properties of the lignite seams at any desired surface coordinate position between core hole locations. The wide range of application shown by this study indicates that the methods of statistical regression analysis may be useful to evaluate large deposits of lignite or higher rank coal.

Jan 1, 1969

By J. W. Eckerd

The crushing of chestnut-size (1-5/8 by 13/16 inch) Pennsylvania anthracite in four commercial crushers (impact) jaw) hammer-mill) and gyratory types) was studied by the Bureau of Mines to determine which could produce the largest proportions of buckwheat Nos. 1 and 2 sizes (9/16 by 3/16 inch). Single pass dry and wet crushing techniques and the effect of stage crushing were evaluated. Calculations were made to show the effect of closed-circuit reduction on production rates and yield of the various sizes. The data show that the gyratory crushers produced the greatest percentage of the desired sizes. A ring-type hammer mill produced the greatest tonnage of buckwheat No.1 and rice (14.9 tons per hr.) during dry grinding tests) but the yield of these sizes was only about 55 percent) as compared with 62 to 70 percent for the gyratory crushers. The impact and jaw crushers produced the smallest amount of buckwheat and rice and the largest quantity of oversize material.

Jan 1, 1960

By Mark I. Copeland

The formation of A1203 dispersoids 0,14 and less in size in dilute iron-aluminum alloys by internal oxidation in wet hydrogen and dispersion strengthening of iron by application of the technique to iron powder were found to be feasible by the Bureau of Mines. In flowing H2-1.5 H20 gas, A1203 dispersoids 0.1w and less in size formed (at 650° to 750° C) in Fe-l and 2 Al sheet material but not in Fe-3 or 4 Al alloys. With higher temperatures and/or higher H2O/H2 volume-ratio gases, A1203 and FeA1204 dispersoids >0.14 in size formed in all the sheet materials- Minus 100-mesh Fe 2 Al powders were internally oxidized under conditions that promoted formation of fine A1203 particles in sheet material, and then the oxidized powders were hydrogen reduced, sintered, extruded, and evaluated. During internal oxidation, fine A1203 dispersoids formed within the powder grains, and coarse FeA1204 particles formed on the powder surfaces and grain boundaries. The FeA1204 content was essentially eliminated during sintering by reacting with the unoxidized aluminum that remained in the center of the larger internally oxidized powders. The tensile strength at 800° C depended upon the aluminum-oxygen weight ratio of these elements in the extrusions and reached a maximum of 17,000 psi. The stress-rupture strengths at 800° C of the better alloys were comparable with those of type 310 stainless steel.

Jan 1, 1972

By D. E. Banks, J. K. H. Ma, Y. Rojanasakul, J. Y. C. Ma, C. J. Malanga

There is evidence to suggest that cell injury induced in alveolar macrophages (AM) following phagocytic activation by silica particles may be mediated through changes in intracellular free calcium [Ca 2+}. However, the mechanism of silicainduced cytotoxicity relative to [Ca2+], overloading is not yet clear. To provide a better insight into this mechanism, isolated rat AMs were exposed to varying concentrations of crystalline silica (particle size< 5 µm in diameter) and the fluctuation in their [Ca2+]; and cell integrity were quantitatively monitored with the fluorescent calcium probe, Fura-2 AM, and the membrane integrity indicator, propidium iodide (Pl). Results from this study indicate that silica can rapidly increase [Ca2+]; in a dose-dependent manner with a characteristic transient calcium rise at low doses (<0.1 mg/ml) and an elevated and sustained rise at high doses (>0.1 mg/ml). Depletion of extracellular calcium [Ca 2+]0 markedly inhibited the [Ca2+]; rise (˜90%), suggesting that Ca2+ influx from extracellular source is a major mechanism for silica-induced [Ca2+]; rise. When used at low doses but sufficient to cause a transient [Ca2+]; rise, silica did not cause significant increase in cellular Pl uptake during the time of study, suggesting the presevation of membrane integrity of AMs under these conditions. At high doses of silica, however, a marked increase in Pl nuclear fluorescence was observed. Depletion of [Ca 2+] 0 greatly inhibited cellular Pl uptake, induced by 0. 1 mg/ml or higher doses of silica. This suggests that Ca 2 + influx, as a result of silica activation, is associated with cell injury. Indeed, our results further demonstrated that the low dose effect of silica on Ca 2+ influx is inhibited by the Ca2+ channel blocker nifedipine. At high doses of silica (>0.1 mg/ml), cell injury was not prevented by nifedipine or extracellular Ca2+ depletion, suggesting that other cytotoxic mechanisms, i.e., nonspecific membrane damage due to lipid peroxidation, are also responsible for the silica-induced cell injury. Silica had no significant effect on cellular ATP content during the time course of the study, indicating that the observed silicainduced (Ca2 ... ); rise was not due to the impairment of Ca2 + -ATPase pumps, which restricts Ca2+ efflux. Pretreatment of the cells with cytochalasin B to block phagocytosis failed to prevent the effect of silica on [Ca2+]; rise. Taken together, these results suggest that the elevation of [Ca2+]; caused by silica is due mainly to Ca2+ influx through plasma membrane Ca2+,channels and nonspecific membrane damage (at high doses). Neither ATP depletion nor Ca2+ leakage during phagocytosis was attributed to the silica-induced [Ca2+]; rise.

Nov 1, 1995

By D. Harrington

Springing or chambering of deep drill holes is common practice in some quarries. It involves definite hazards from premature explosion during placing of the springing charges or the final charge due chiefly to heating of the bottom of the holes by the successive exploding of the springing charges or, in some instances, from burning of paper or other material following detonation of the explosives The danger is either unknown or disregarded in many instances by those who place the charges in the holes. Disregard of this hazard probably is, at least in part, responsible for the far too high fatality and injury rate due to charging explosives and premature slots in quarry work. Awareness of the danger&apos; should result in elimination or at least of material decrease in injuries from this cause.

Jan 1, 1941

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968

By E. D. Gardner

During the summer of 1935 a plan was proposed by which the Government should establish custom sampling plants for gold and silver ores in the mining districts of the West, where the construction of such plants would be justified as an unemployment relief measure. It was known that in many districts prospectors and small operators had small lots of smelting ore that could not be marketed for lack of sufficient capital to get out enough ore at a time to make carload shipments to distant smelters. Moreover, considerable ore of milling grade was available in many districts in which there were no custom milling facilities. It was felt that. accurate sampling and the classification and consolidation of small lots of ore produced from prospects and small mines, with quick cash returns to the shippers on a nonprofit basis, would stimulate the working of small gold and silver properties: Idle mines would be put to work, and there was a possibility that some of the prospects could be developed into regularly producing mines. Each sampling plant was to be centrally located so as to serve the greatest possible number of mines and prospects. Wherever possible, the plants were to be built on a railroad, is ore of smelting grade accumulated, it was to be shipped to a smelter in carload lots. Where a plant was not on a railroad, smelting ore was to be trucked to the railroad after being sampled.

Jan 1, 1936

By Roy E. Peterson

The Bureau of Mines conducted an investigation to produce metallized pellets from domestic iron ore superconcentrates using lignite and subbituminous coal as reductants. Feed materials for the metallizing process consisted of commercially indurated iron oxide pellets and green pellets prepared from upgraded domestic concentrates with graphite or limestone as internal additives. Durability of the green pellets during metallization was investigated in tests conducted in a 7-inch-ID rotating drum furnace. Test results indicated that the major cause of pellet disintegration with the concentrates used was the tumbling action during reduction rather than forces generated within the pellets. In larger scale tests made in a 34-inch-ID by 35-foot-long kiln, the previously indurated pellets were metallized with lignite at 1,030° C with little disintegration. A 96-percent level of metallization was obtained in pellets having an average compressive strength of 420 lb. In subsequent, similar tests using green pellets containing graphite or limestone, pellet disintegration was more severe, with 10 to 40 percent of the feed being lost as dust. The surviving pellets had metallizations ranging from 88.3 to 94.4 percent and compressive strengths ranging from 60 to 68 lb.

Jan 1, 1976