Search Documents

By C. A. Kumke

The Korean crisis and the cessation of Russian manganese-ore shipments to the United States in 1950 reemphasized the almost total dependence of the domestic steel industry on foreign supplies for metallurgical-grade manganese ore. In this emergency, Congress authorized the Bureau of Mines to undertake experimental mine and process development work on the known large reserves of low-grade manganese ore in the Artillery Mountains region in Mohave County, Ariz. The objective of the work was to obtain the basic mining and metallurgical data needed to make specific plans for initiating exploitation of the deposits within 3 years if high-grade foreign ore could not be obtained during the emergency. The manganese deposits of the Artillery Mountains region are in an area of about 25 square miles on the north side of the Bill Williams River in southern Mohave County. Lasky, of the Federal Geological Survey, has estimated reserves at 175 million tons of manganiferous material assaying 3.5 to 4 percent Mn. Although the man¬ganese occurs in various Tertiary and Quaternary formations as both bedded and fissure vein deposits, the more important syngenetic deposits are found in upper and lower manganiferous zones in the sedimentary beds of playa and alluvial fan origin that constitute the Chapin Wash formation.

Jan 1, 1957

By Ralph B. Youtz

This paper describing mining methods at, the Eighty-Five mine of the Calumet and Arizona Mining Co., Valedon, N. Mex., is one of a series being prepared by the United States Bureau of Mines on mining methods, practices, and costs in the various mining districts in the United States. The Eighty-Five mine is in southwestern New Mexico, 3 miles southwest of Lordsburg, Hidalgo County (see fig. 1). The mine produces normally 7,000 to 8,000 tons per. month of silicious copper-gold-silver ore, and employs approximately 200 men underground and 40 on-the surface. Mining is done by shrinkage and cut-and-fill methods.

Jan 1, 1931

By A. J. Barry

A method was developed for testing the anchorages obtained with 3/4-inch, expansion-type, headed bolt and shell assemblies. The apparatus is a modification of that used in testing -inch-diameter, slotted-type bolts. Four makes of expansion-type shells were used in 64 tests made in sandstone and shale roof. The results show that for 3 makes of shells the anchorage effectiveness is independent of the installed land, and for the fourth make of shell a better anchorage is obtained when instilled at a load of 8,000 pounds. The results also show that deformation of the expansion plug influences the majority of the anchorages obtained with two makes of shells. This deformation causes a larger increase in displacement for a given added increment of load. The data from 48 of the 64 tests were combined to establish a relationship between average displacement and increase in bolt load (above the installed load). This relationship can be used to evaluate the anchorage effectiveness of any 3/4-inch-diameter, expansion-type, headed bolt and shell assembly tested in the field.

Jan 1, 1956

By E. A. Johnson

The Bureau of Mines determined the effect of slag additives on copper solubility and the distribution of typical impurity elements between copper-iron matte and silica-saturated fayalite (iron silicate) slag at 1,250° C, in CO-C02 atmospheres with 10 pct S02. Small additions (<10 pct) of CaO, A1203, and MgO were shown to decrease copper solubility in the slag. Additions of CaO increased the solubility of bismuth and tellurium in the slag at lower matte grades. Al 20 3 additions decreased the solubility of tellurium in the slag, but increased that of bismuth at lower matte grades. A1203 additions increased the solubility of both at lower matte grades. With no additives, matte grade did not affect the solubility of bismuth in slags, whereas increasing matte grade resulted in a slight decrease in the tellurium solubility in slag. Additions of CaO or As203 alone to the slag increased selenium and arsenic distribution to the matte, but had little or no effect on antimony distribution; whereas small MgO additions decreased antimony distribution to the matte but had no effect on arsenic and selenium distribution. In slags with no additives, selenium distribution to the matte increased with increasing matte grade, while that of antimony decreased and that of arsenic was unchanged.

Jan 1, 1982

By Hylton R. Brown

Although extensive research has been carried on to determine the factors affecting the explosibility of carbonaceous dusts, as much has been published on coal-dust and grain-dust explosions recent reports of loss of life and property in explosions if metal dusts emphasize the lack of information on the extent of the dust-explosion hazard in plants manufacturing or handling; aluminum, magnesium, or zinc powder, as well as other metal or mineral dusts. Early investigators believed that only the carbonaceous dusts formed explosive mixtures with air, and it was not until near the beginning of the present century that the explosibility of certain metal and mineral dusts was recognized generally. In his book, entitled "Fire and Explosion Risks," published in 1904, Von Schwartz called attention to such hazards. Many vague references to metallic-dust explosions are found in the literature, such as "a severe explosion of aluminum dust occurred in the Middle West several years ago," but very little information seems to be available on the extent of the hazard, the number of explosions, or the amount of loss caused by explosions in pants handling metallic or mineral dusts or powders other than those of a carbonaceous nature. A search of the records of insurance companies, rating bureaus, fire underwriters,and fire-protection associations as well as the files and records of Government agencies has been made to obtain authentic data on explosion losses. To indicate the extent of the hazard a summary of laboratory tests covering the explosibility of certain metal dusts, with brief reference to their uses and Methods of manufacture, and the data compiled from the information available on losses are presented in this publication.

Jan 1, 1941

By Forrest T. Moyer

The overall injury experience, excluding officeworkers, at metal mines and mills during the period 1961-63, reported by operators, was 174 fatal and 11,357 nonfatal disabling work injuries during an aggregate worktime of 451 million man-hours. These injuries occurred at a frequency rate of 25.55 per million man-hours, comprising 0.39 for the fatal and 25.17 for the nonfatal injuries. The combined severity rate of the disabilities was 3,779 days lost or charged per million man- hours, consisting of 2,314 for the fatal and 1,465 for the nonfatal injuries. The average severity of all disabilities during 1961-63, was 148 days per injury. The number of days lost and/or charged, ex- cluding officeworkers, at metal mines and mills during the period 1961-63, was 1,440,000 days charged to fatal injuries and 661,290 days lost from nonfatal injuries. An average of 70,966 men were at work daily. The outstanding cause for fatal injuries was the fall of rock or ore from the back, while most of the nonfatal injuries were caused by handling materials, slips or falls of persons, machinery, falls of rock or ore from back and side, and haulage. Injury experience at primary nonferrous smelters, refineries, and reduction plants during 1961-63, excluding officeworkers, was 23 fatal and 3,214 nonfatal disabling injuries during a total work- time of 277 million man-hours. The injuries occurred at frequency rates of 0.08 per million man-hours for the fatalities and 11.61 for the nonfatal disabilities. The severity rate for all injuries of 1,085 days lost or charged per million man-hours comprised 498 for fatal and 587 for nonfatal injuries. The number of days lost, excluding officeworkers, at primary nonferrous smelters, refineries, and reduction plants during 1961-63 was 138,000 from fatal injuries and 162,385 from nonfatal injuries, An average of 34,938 men were at work daily an active plant days during the three year period. The injury experience for officeworkers at metal mines and mills during the period 1961-63 was 20 nonfatal disabling work injuries, (there were no fatal injuries reported), during an aggregate work-time of 28,694,244 man-hours. These injuries occurred at a frequency rate of 0.70 per million man-hours. There were no fatal injuries reported for officeworkers at non-ferrous smelters, refineries, and reduction plants during 1961-63, but seven nonfatal injuries were reported during an aggregate work-time of 30,814,772 man-hours. The frequency rate for these injuries was 0.23 per million man-hours for this period.

Jan 1, 1967

By E. D. Gardner

During the summer of 1935 a plan was proposed by which the Government should establish custom sampling plants for gold and silver ores in the mining districts of the West, where the construction of such plants would be justified as an unemployment relief measure. It was known that in many districts prospectors and small operators had small lots of smelting ore that could not be marketed for lack of sufficient capital to get out enough ore at a time to make carload shipments to distant smelters. Moreover, considerable ore of milling grade was available in many districts in which there were no custom milling facilities. It was felt that. accurate sampling and the classification and consolidation of small lots of ore produced from prospects and small mines, with quick cash returns to the shippers on a nonprofit basis, would stimulate the working of small gold and silver properties: Idle mines would be put to work, and there was a possibility that some of the prospects could be developed into regularly producing mines. Each sampling plant was to be centrally located so as to serve the greatest possible number of mines and prospects. Wherever possible, the plants were to be built on a railroad, is ore of smelting grade accumulated, it was to be shipped to a smelter in carload lots. Where a plant was not on a railroad, smelting ore was to be trucked to the railroad after being sampled.

Jan 1, 1936

By J. W. Horne

The United States Bureau of Mines in cooperation with the State of Colorado at the University of Colorado has conducted experiments to determine the amount and composition of the noncondensable cases evolved when crude shale oil is distilled under pressure. Hydrogen sulphide is one of the components found in the complex mixture of uses produced by the distillation of shale oil under pressure. This paper deals with the apparatus and method used in determining the amount of hydrogen sulphide evolved in the laboratory experimental cracking stills.

Jan 1, 1931

By O. C. Blade

This report on the properties of aviation gasolines and aviation jet fuels produced in the United States during 1955 was made under a co-operative agreement between the American Petroleum Institute and the Bureau of Mines of the United States Department of the Interior. Analytical data are presented for 116 samples of aviation gasoline and for 38 samples of aviation jet fuel. The analyses were made on samples typical of the manufacturers&apos; 1955 production in their laboratories and the results submitted to the Bureau of Mines for compilation. The products of 20 manufacturers of aviation gasolines and of 16 producers of aviation jet fuels are represented.

Jan 1, 1956

By W. A. Dunkley

During the past year and a half the Western United Corporation of Aurora , Illinois , has been distributing carburetted water ges from its Lockport , Ill . , plant , to an extensive territory , under an initial pressure ranging up to 90 lb.. per sq. in . The most distant distributing point on the system is at Harvard , Ill . , about 35 miles from the plant.. The territory supplied is approximately 85 miles long and 35 miles wide , the total mileage of rains being 1223 , or approximately 24 per cent of all the gas trains in Illinois outside the city of Chicago .

Feb 1, 1923

By E. J. Lintner

This paper is one of a series being prepared by the United States Bureau of Mines describing clay mining, crushing, and grinding methods and costs at various operations throughout the United States. These papers are designed to disseminate technical information regarding methods used. The cost tabulations represent local operating expenditures only and not total production costs. It is recognized that in many instances publication of total production costs may cause embarrassment to the individual operator as well as to the industry as a whole. On the other hand, operating costs are essential to a technical discussion and study of the methods employed. The attention of the reader is called specifically to this differentiation in order that no misunderstanding of the scope of the cost tabulations shall ensue. The following report deals with the methods employed by the Malvern Clay Co., Malvern, Carroll County, Ohio. The author wishes to acknowledge the assistance of the following persons: H. C. Ross, vice-president and general manager, and H. C. Dormer, secretary and treasurer.

Jan 1, 1937

By W. L. Hunter

This report describes results of beneficiation and smelting studies conducted by the Federal Bureau of Mines on chromite samples from the Emma Belle and Seiad Creek prospects in the Seiad Creek area, northern California. Samples were chosen from this area because the ore is typical of disseminated types that represent a sizable domestic reserve. The two samples were similar in composition, and both responded in like manner to gravity beneficiation. As the ore was banded, considerable coarse gangue was rejected in laboratory sink-float from a minus-3/4-inch, plus-6-mesh fraction without excessive chromium loss at a medium density of 3.32. An average of 85.6 percent of the chromium was recovered in the sink product, which analyzed 35 percent chromic oxide (Cr203). Tabling yielded concentrates containing 49 percent or more Cr203; however, recoveries, ranged from only 33 to 45 percent. A combination of tabling and electrostatic separation of the table middlings showed that the chromium recovery could be increased to about 73 percent; the composite concentrate averaged 53 percent Cr203.

Jan 1, 1960

By B. H. Clemmons, B. G. Saunders, R. H. Stacy

"INTRODUCTION This investigation was undertaken to determine the response of Birmingham (Alabama) red-iron ore to heavy-medium concentration. Specifically, the work involved a study of the efficiency of the process in separating coarse gangue diluents from the ore and an endeavor to evaluate the potential economic results. The investigative work was not intended, nor is it to be construed, to be adequately exhaustive in scope to enable immediate plant construction. Rather, the primary objective was to determine the grade of ore that could be produced by heavy-medium treatment and the resulting indicative or tentative benefits to be derived from such treatment. The latter, in turn, would determine the merits of the more exhaustive study that would be required for an ultimate decision on the heavy-medium treatment of the ores.The problem of avoiding excessive contamination of red-iron ores by shale and/or ferruginous sandstone has been before the operators of the iron mining industry of the Birmingham, Alabama, district for many years. Within the last two decades, increased mechanization of mining methods has increased this contamination to a considerable degree. In fact, general utilization of scraper loading and other mechanical methods of mining, in conjunction with small increases in the natural insoluble content of the ores, in some cases has actually resulted in the production of ""acid"" or excessively insoluble ore, where ""basic"" or excessively lime ores were produced formerly.The contaminating materials are derived largely from roof spells and natural parting seams in the ore, a condition that to some extent has been aggravated by the irregularity of the ore beds. The latter have been subjected to both primary and secondary folding in many places. Considerable faulting has taken place, also. In many localities these conditions render virtually impossible complete avoidance of ore contamination from the over and underlying sandstones and shales. However, in a few localities, where the ore beds are less disturbed and shale partings are absent, mining can and is being accomplished with relatively little dilution."

May 1, 1948

By G. W. Grove, H. R. Burdelsky, F. E. Griffith

"INTRODUCTION The work of using a system of air locks in unsealing a mine in Ohio following a fire probably was one of the outstanding jobs of its kind in a medium-thick coal bed.The fire in this mine, thought to have been of electrical origin, was discovered at about 1:30 a.m. on December 11, 1941. Forty-four men were working in the affected section at the time; 5 escaped unassisted, and 37, who had barricaded themselves, were rescued. The bodies of two men, who had succumbed after breathing fumes given off by the fire, were brought part way out of the mine before it became necessary to seal the mine.Direct attempts to extinguish the fire with water were abandoned when hazardous amounts of 'carbon monoxide, methane, and other inflammable gases were detected in return air passing through the main haulageway and escape-way of the mine.The mine was completely sealed on the surface at about 8 p.m. on December 12, 1941, with the two bodies remaining in the mine. Sixteen days after the mine had been sealed, the two bodies were recovered. This was accomplished by air-locking through a partitioned-off stairs compartment of a ventilation shaft. This work was done under adverse barometric and atmospheric conditions.A method for collecting representative air samples from the immediate fire area was used successfully by utilizing a vacuum pump on about 10,000 feet of existing water line that had been broken near the fire area.The immediate fire region was sealed, and confined to a relatively small area; the remainder of the mine was recovered, and operations were resumed February 9, 1942, or 59, days from the time of sealing the mine on the surface. This recovery was made by air-locking the main entries inby from the shaft and No. 2 right-face entries.The distance between air locks averaged about 500 feet, and as each new set of seal stoppings and air locks was completed, the old or outby seals were taken out and the area between was ventilated. In ventilating this area, it was often necessary to use line curtains to direct the air into dead-end places."

Oct 1, 1947

By James P. Bennett

The Bureau of Mines investigated the effect of refractory oxide additions, introduced in soluble form, on the high-temperature properties of 90- and 98-pct-MgO brick. Brick samples were soaked in solutions containing Al, Ca, Cr, Co, Fe, Mg, Mn, Mo, Ni, Si, Sr, Sn, Ti, or Zr ions. Additions to 98-pct-MgO brick did not generally result in statistically significant property improvements. Statistically significant improvements were noted in hot modulus of rupture (MOR), slag resistance, and spalling resistance of the 90-pct-MgO brick for additions of Al, Mg, or Sn. High-temperature performance of treated 90-pct-MgO refractories was equal to or approached that of 98-pct-MgO brick. The marked improvements due to tin were obtained with additions of only 1.14 wt pct Sn02.

Jan 1, 1985

By E. F. Foerster

The Bureau of Mines used a diphenyl ether calorimeter to determine the heat contents of natural and synthetic blast-furnace slags. For solid slags, enthalpy (HT-H298) at 1,448° to 1,680° K ranged from 282.1 to 348.5 cal/g (±3 percent); liquid slag values were 400.1 to 514 cal/g (±3 percent) in the temperature range between 1,626° and 1,890° K. Experimental results for liquid slags were 14.3 to 16.2 percent higher than the enthalpies calculated from thermodynamic tables; values for solid slags ranged from 5.3 percent lower to 3.9 percent higher than calculated values. Experimental results for liquid synthetic slags ranged from 14.9 to 24.3 percent higher than the calculated enthalpies; values for solid synthetic slags were from 1.0 to 3.4 percent higher.

Jan 1, 1967

By F. G. Miller

[Petroleum technoloF;istz and 1 rot-re s s ive OT e:?ztors. con stantl;, are striving to increase the percentage of oil that y to recovered from reservoir rocks throe::;:: wells. The exhaustive studies that have been made of the function of natural r:; as in t h-_ T r odI action of oil, for cx<n.mTnle, have aidedd of.erators greatly in incroasin,&apos; the q-:Arrntity of oil recovered from reservoirs. i.rtural gas dissolv3d in ar--d otinerwwisa &apos;1s&apos;.,ocintjd under rre3suro with oil in roscrvoir roci.s, howover, i:; not the only source of energy available for moving oil through sa&apos;:&apos;l to wells. l becoming "reservoir-energy conscious&apos;t engineers hr-vo -d o^.rued t}:-Lt in many petroleum reservoirs the edgewater flanking t -,e oil accum.-,lation conetitutos a potential source of onergy capable, tL-ou;_h rro? gr control, oil&apos; increasing oil-recovery efficiencies materially. i o ]enter is ti-.-,, on-cronchinunt of water into the oil- and gas--fillod ?art of the reservoir considered as an evil to be combatted by devious mot&apos;:r:ci :i,.t r,ttL er a natural conseque::c4, incident to the withdrawal of oil nna gas from the wells, that nay be T.usod advantrt eou ;ly in lonr`t}toning tr e r&apos;lowin g lift of wells a.nd, i norcas in:; the economic recovery of oil and Little is known about the by which water off: oratos in driving nil throe:gh reservoir roc:-.:,, nd i:. a scorcity of rubli:;Lad informs-¬t .on nn rates of :)Ov.:m.,:- t of : r.tcr ..at v:1:11 res,-_lt in ^r i-nu oil recoveries. Bureau of :fines engine_:? ; - reciate. the r,aucity of scientific knowledge or. the &apos;test methods of a,r.lying the natural water arive to in¬crease oil-recovery efficiencies ant ,i.;?l __-itir?,~ ting irties that will, they hope, Contribute to t.1&apos;.e T ros?Jr.t. small _ %nd of information now av tilable on tt:e cubjoct. This r».crt a oyno-.::is or brief comrilnt.ion of r,ublished data and thought accuinulnt.~d so far, to la)or;~.tory ox-:erimnntrr¬tiorn and, further rosoarch on the z_rrinciplos unri;rlyir..g the natr.rr+1 eater drive no it nffocts oil recovery. :Lie writer:: Lore that t.i.c cx-nositiorn of a?rzilable inforr-at ion i rcs?r.toi in the rernrt r .-II .i ,.1rtt cor_jt_-i:ctive tho.-_.I_t and efforts loadir,-z to -:ard more con.r .ote extraction n;&apos; o tl from reservoirs.]

Jan 1, 1938

By Joseph M. Pugliese

The U.S. Bureau of Mines has produced a generic in situ copper mine design manual, which contains a computerized cost model for in situ copper oxide mining. The model specifies (1) site-specific parameters, which must be quantified for mine design, (2) a method for minesite design based on those parameters, and (3) a procedure for assessing economic viability for the mine design. The menu-driven computer program performs calculations for developing commercial mine design specifications, as well as capital and operating costs. The default values are based on 1986 dollars, and indices for updating costs are included. The program also provides discounted-cash-flow rate of return (DCFROR) and allows for sensitivity analyses for an in situ mining operation at any specific undisturbed copper oxide deposit. This report is to be used with the 1990 version of the computer program, which has been made user friendly. It describes the flies, tutorial, input phase, help function, and monitor display of all calculated values and of the DCFROR table. The monitor-displayed discounted initial value of investment and annual operating costs are defined. The dual rate-of-return situation and sensitivity analyses are also briefly discussed. Information is provided on obtaining the computer program on diskette.

Jan 1, 1991

By J. E. Allison

As part of a Bureau of Mines research program to conserve critical and strategic metals, an aqueous electrodeposition method for preparing stainless-steel-type coatings was studied. Chromium powder (averaging 3 J1.m diam) was suspended in a ferrous-nickelous sulfate electroplating bath and occluded in the electrodeposited Fe-Ni alloy matrix. Subsequent heat treatment of the resulting composite coating formed the ternary alloy. The occlusion process was affected by the quantity of Cr powder suspended in the electrolyte and by the microstructure and composition of the electrodeposited matrix. Coatings containing up to 21 wt pct Cr were deposited from an electrolyte containing 20 vol pct suspended Cr powder. Heat treatment at 1,100° C for 8 h homogenized the composite coating. Deposition of 44Fe36Ni20Cr alloy coatings (250 J1.m thick) on AISI 1020 carbon steel rods, followed by heat treatment, provided complete protection of the carbon steel during exposure to a boiling 65-pct-HN03 solution. Corrosion rates of 0.6±OA mm/yr for the coating in the boiling HN03 approximate that of 304 stainless steel. Practically shaped electroforms have been prepared by the coating method.

Jan 1, 1989

By Edwin M. Murphy

Methods are described for filling underground cavities remotely with dry material pneumatically injected through a borehole to seal openings, prevent air movement, and reduce subsidence; this often brings underground fires under control by limiting the access of air. Large-scale tests were made in the Bureau of Mines Experimental Coal Mine, Bruceton, Pa., in an operating mine, and in an abandoned Pennsylvania mine. Supplemental trials were made aboveground in galleries and in the laboratory. The parameters studied include horizontal and inclined passageways, obstructions in the entry, water leakage into the borehole, dry material, and grout and slurry mixes. The materials studied were fly ash, crushed and pulverized limestone, and sand. Best results were obtained with dry fly ash, though satisfactory seals were obtained with the other materials. When a borehole is dry and ends at an open void, casing is not necessary. If more than 5 gpm of water flows in the borehole, if the void contains loose debris, or if coarse material is injected, a material feedpipe should be inserted through the borehole. Fly ash was most suitable for remote filling because of its low angle of repose (8°) and its good flow characteristics. The depth of borehole through which the fly ash is injected has no appreciable effect on the filling operation.

Jan 1, 1968