Search Documents

By P. G. Pigott

This Bureau of Mines laboratory research demonstrated that building bricks meeting ASTM specification C62-66 for grades SW and MW of FBS-type bricks can be produced from waste copper mill tailings. Waste tailings from accumulations at Magna, Utah, Anaconda, Mont., and Hayden, Miami, and San Manuel, Ariz., were dry-pressed into bricks, and the products were tested in accordance with ASTM Designation C67-66 on sampling, and testing of brick. An evaluation derived from pilot-plant production of similar brick at the Coal Research Bureau of West Virginia University indicated the production cost to be about $34 per 1,000 bricks. Utilization of such mill tailings on a commercial scale would eliminate the need for digging new pits for brick raw material production, conserve natural resources, and simultaneously remove potential sources of air pollution.

Jan 1, 1971

By Jack L. Henry

A laboratory and a pilot-plant-scale investigation has been conducted by the Bureau of Mines to examine possible sources of nitride defects in the production of magnesium-reduced titanium sponge. The production of alpha-stabilized nitride inclusions in hot-rolled titanium plate from air contamination of sponge during its manufacture has been experimentally demonstrated. Magnesium-reduced sponge prepared from air-contaminated magnesium or when contaminated by an air leak during reduction, vacuum distillation, or inert gas sweep, shows very large variations in nitrogen content. Refractory nitrides, delta TiN and epsilon Ti2N have been identified in this sponge. The highest incidence of inclusions resulted from sponge that was reduced by air-contaminated magnesium and from sponge subjected to air contamination during the vacuum distillation cycle and during helium sweep. Air contamination of sponge during the reduction cycle was not nearly as effective in producing inclusions. Tests showed that color and texture may not be reliable criteria for locating defects during sponge inspection. Maintenance of good vacuum-tight integrity, filtration of molten magnesium prior to charging into the reduction retort, and mechanical attrition of sponge to pulverize and disperse nitrides are suggested as practices to lower inclusion incidence in commercial titanium ingots.

Jan 1, 1974

By Robert B. Worthington

This investigation was undertaken to develop a more efficient copper smelting practice that would help meet the increasingly stringent antipollution standards. Continuous smelting to copper and a 0.8-to 5-percent copper slag using pure oxygen has been demonstrated for several hours at a time in a unique double furnace, which was devised to overcome the heat losses inherent in a laboratory furnace. The use of pure oxygen to effect the smelting and conversion of copper sulfide concentrate in a single unit to produce blister copper and a very high S02 concentration provides a much reduced gas volume for more economical and thorough sulfur recovery. Although the process was successfully demonstrated for several hours at a time, extended test work using longer runs will be required to balance the system and to obtain test data for adequately demonstrating its technical feasibility.

Jan 1, 1973

By David C. Grant

In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated.

Jan 1, 1985

By McHenry Mosier

The application of diamond drills for blast holes is limited to the special Job of extracting floor and stope pillars, and therefore their operation is intermittent. The zinc ore drilled occurs in metamorphosed dolomitic limestone. The mining method is sublevel open-stoping on 200- foot lifts. Ample fresh air is provided by mechanical ventilation. Diamond drilling blast holes began in August 1944. Drills were mount- ed on a 3-inch quarry bar. The contract price for labor for operating equipment owned by the company was $0.23 per foot. The diamond bits were cast-set at the factory in a sintered tungsten matrix. Bit replacement costs were $0.15 to $0.20 per foot drilled. The feet drilled per bit ranged from 87 to 258. The feet drilled per diamond-drill shift ranged from 121 to 129. Holes were loaded with 60-percent special gelatin dyna- mite and fired electrically. In percussion drilling, the estimated feet drilled por machine shift with hand-held sinkers was 65. The tons broken per machine shift averaged 40 throughout the mine. Detachable bits have been adopted recently. The principal advantage of diamond-drilling blast holes at the Balmat mino is the extraction in a safe manner of ore not minable by short-hole drilling. The principal disadvantago is the greater cost per foot of holo in comparison with percussion drilling.

Jun 1, 1947

By R. S. Dean

[Methods s of preparing the manganese metal that has been used in chemical and metallurgical investigations have passed through a cycle. Most of the investigations made e before the turn of the century, used Moissan's pyrophoric man manganese.3/ This material was made b; electrolysis into a mercury cathode and distillation in vacuo. The material was essentially pure, and investigations in which it was employed (with proper precautions against oxidation) led to accurate results on tie intrinsic behavior of metallic manganese.]

Jan 1, 1941

By William C. Cooley

[Data from t.-raturs on each hydr,ne has been assembled on the- data sheets whichw6ed in this Appandin. Dai_iis are provl_ od for ::amines or hydraulic s-ctions in the USSR (TDPhw~s), 8 in ASR (Kuzbass) , 1i-gin i, 1 in 7in China, i in Japan, and l in C~n- i.Ata sheetsiov tion prepared for mines in New Zealah_~sddered very rele¬ vant, nor forf !aA of information. In aW,!~.F in : --- C=SR for tiara ShoeLS ara 1palAwdl satinieral mines have operac- ~ - re Manned about which very limited data exist as folloos:]

Jan 1, 1975

By E. A. Rowe, G. H. Keith, B. D. Jones

An evaluation of electrowon tungsten powder was made by comparing its characteristics with conventional hydrogen - reduced tungsten powder . Electrowon tungsten powder was investigated with respect to particle size and shape , apparent density , flow rate , compressibility , green strength , and sintering characteristics . In addition , its chemical purity , absolute density , and purification by melting were determined . Significant findings were higher flow rates and better compressibility than hydrogen - reduced tungsten powder . However , the large particle size peculiar to the electrowinning process effectively prevented conventional sintering to a high- density material . The possibility of producing high - density material , using a new technique of hot swaging sheathed sintered - tungsten compacts , was demonstrated by the achievement of densities of 92 percent of theoretical .

Jan 1, 1965

By S. J. Broderick

[The term "nonmetallic minerals,? as commonly used in the mining industry, refers to those minerals of industrial importance that are mined essentially for uses other than for the metals contained. The field comprises several hundred minerals of industrial importance, of which 70 have been adequately described in the textbook Industrial Minerals and Rocks.3/ A few of the more important nonmetallic products are sand and gravel, salt, phosphates, clays, refractories, linestone, and cement materials. Some of tic minerals, such as bauxite and pyrolusite, have both metallic and nonmetal is applications, but in this report only the nonmetallic mineral phases are considered. In the organic field of nonraetallics only coal is considered, as, the, others - petroleum, natural gas, natural bitumens, and hydrocarbons - are of no importance in water softening.]

Jan 1, 1941

By G. W. Jones

"INTRODUCTION As part of its work in promoting safety, the Bureau of Mines is investigating various means of eliminating or mitigating the explosion hazards of combustible gases encountered in mining and industry. Information has been obtained and a procedure developed whereby the explosibility of many complex gaseous mixtures may be calculated in a rather simple manner without the necessity of performing laborious laboratory experiments. An earlier publication 3/ described the method of determining by calculation the limits of inflammability of gaseous mixtures, including methane, hydrogen, carbon monoxide, nitrogen, carbon dioxide, and oxygen. The information published in the above report permitted calculation of the limits of inflamnability of such gases as are liberated by mine fires, gases from explosives, automobile exhaust gases, gases present after mine explosions, blast-furnace gas, and other gases of similar type.Gases liberated in certain potash mines in the western part of the United States sometimes contain ethane, in addition to the gases named. An investigation was made to obtain data from which the limits of inflammability of such gaseous mixtures could be determined by calculation. 4/Similar data have been Published covering all types of natural gases containing wide ranges of concentration of nitrogen and carbon dioxide.5/"

Dec 1, 1944

By P. D. Lohn

The objective of this program was to develop nozzle designs to maximize the effective cutting length of a water jet. The results of the theoretical program directly support the Bureau of Mines Borehole Mining Program and their experimental program to improve the rock cutting capability of water jets. The borehole geometry requires turning the flow by 90 degrees and accelerating through the nozzle within a restricted length. Several suggestions for turning the flow are offered. The borehole space limitations constrain nozzle length, to the extent that a standard 13-degree tapered nozzle (6-1/2 degrees half angle) is too long to fit in the borehole, at production flow conditions. The design technique developed is computationally economical and enables examination of a large number of shapes and flow conditions. The nozzle design is based on design criteria of minimization of boundary layer thickness at the nozzle exit and minimization of the possibility of separation and cavitation. Six flow conditions, including pressures to 4500 psi and flow rates to 400 gpm, were examined, Best shapes were determined for all flow conditions. The best shape for a borehole reining application consists of an initial 4th degree polynominal (quartic) at the entrance followed by a straight section with a twenty degree (half-angle) taper at the exit.

Jan 1, 1976

By Forrest T. Moyer

In conjunction -with the statistical survey of the lime industr-.r in 1939, by the Bureau of Hines, producing companies reported the lime-fuel ratios attained in their plants according to type of kiln and kind of fuel. Each ratio, expressed as the number of pounds of lime burned by a unit quantity of fuel, was weighted according to the tonnage of quicklime pro- . duced at the reporting plant and grouped with similar data from other plants, so that an average ratio for each type of fuel and,kiln could be calculated. By this method the variables trat affect ratios of individual plants are more or less equalized, and the computed average lime-fuel ratios provide a fair measure of kiln and fuel efficiencies during 1939.

May 1, 1941

By W. W. Roepke

The linear cutting system, developed by the U.S. Bureau of Mines, uses geometric principles developed by Cardan to produce a nearly constant cut depth. The new system has been extensively tested in a synthetic material under laboratory conditions to verify mechanical capability and to identify operational characteristics. Comparisons between 15-rpm linear cutting and 50-rpm rotary cutting systems show significant improvement in respirable dust entrainment, product size distribution, and energy usage. Respirable dust is reduced by as much as 90 pct. Recovered product showed a 67-pct reduction in -0.32-cm (-1/8-in) material and a 200-pct increase in +5.08 cm (+2 in) material. Average power was reduced by 66 pct for the linear cutting. Because the bit cutting paths differ between linear and rotary cutting, it was necessary to compare the two at the same cut depths and bit types. These comparisons show that low revolution per minute rotary cutting entrains about the same amount of respirable dust as the linear cutting system, but the average shaft torque may be 55 to 130 pct greater for the rotary system.

Jan 1, 2010

By William W. Adams

Accidents to men employed in the quarrying and related industries of the United States were more numerous, absolutely and relatively, in 1937 than in 1936. Fortunately, the entire increase was in the category of nonfatal injuries, as accidents causing death declined in number and in proportion to the number of man-hours worked. Employment increased. More men were employed, more man-days and man-hours were worked, and the average employee had more hours of work than in 1936. Reports covering all commercial operations showed that 84,094 men were employed an increase of 5.1 percent over 1936. The number of man-hours of work performed by the industry was, 158 millions, an increase of 7.6 percent. Seventy-seven men were killed by accidents, a, reduction of 14 from the year before, and 6,348 men were injured and disabled for more than the remainder of the day on which the accident occurred, 11 percent more than in 1936. The fatality rate of 0.49 per million man-hours of exposure in 1937 compared favorably with the rate of 0.62 for the previous year, whereas the non-fatal-injury rate of 40.10 was 3.2 percent higher than the rate of 38.87 for 1936.

Jan 1, 1940

By J. A. Organiscak

Two types of airflow splitting methods for improving longwall dust control were investigated by NIOSH's Pittsburgh Research Laboratory. These methods included a translucent mesh barrier and a staged spray barrier system to confine the shearer-generated dust to the coal extraction side of the longwall face while maintaining a cleaner split of airflow on the opposing worker walkway side of the longwall face. The translucent mesh barrier was shown to provide notable dust control effectiveness up to 60 m downstream of the shearer in both the laboratory experiments and a longwall field evaluation, provided the mesh barrier remains relatively parallel to the airflow. The staged spray barrier system showed marginal dust control effectiveness in the laboratory and subsequently was not field tested.

By M. J. Sapko

The U.S. Bureau of Mines has developed a portable meter for measuring the component concentrations in binary dust mixtures whose constituents have different optical reflectivities. The meter has been successfully tested with coal dust-rock dust mixtures taken from coal mines in Europe and the United States and fluorinated-carbon mixtures that change from carbon black to pure white during fluorination. Additional study has also substantiated the theoretical expressions used in the design of the meter.

Jan 1, 2010

By W. A. Grosh

The Piquette Mining and Milling Co, operates a zinc mine and concentrating mill in the Upper Mississippi Valley zinc-lead district near Tennyson, Wis. The principal ore mineral is zinc sulfide, which occurs in limestones and dolomites of the Decorah formation. Exploration in the district is by churn drilling from the surface. An adit at the base of the ore zone provides access to the mine. A room-and- pillar mining method with irregular pillars is used. Drilling is done with Jumbo-mounted drills. The broken ore is loaded by crawler-mounted front-end loaders into diesel-powered trucks for haulage direct to the mill.

Jan 1, 1959

By Frank E. Cash, Max S. Petersen

"INTRODUCTION Explosives have been used in ever—increasing amounts since gunpowder was invented. For hundreds of years only low explosives of the deflagrating type were used, and they were fired by means of a flame or hot object. Ben¬jamin Franklin first ignited gunpowder from a distance in 1751 by means of an electrostatic spark. Further efforts to develop a satisfactory electrical method to ignite explosives from greater distances were overshadowed by the invention of safety fuse in 1831, as this offered a relatively simple and inexpensive means of firing explosives.The discovery and introduction of high explosives of the detonating type and the invention of the fulmitate of mercury blasting cap about the middle of the nineteenth century provided the needed impetus for inventors to develop means of firing the cap by electricity. The original high-tension igniter, following Benjamin Franklin's experiment in which the detonating compound was ignited by a spark, was discarded in favor of a low-tension igniter, in which the detonating compound was ignited by a heated wire. The past 2 decades have seen considerable improvement in the design and construction of electric detonators to make them safer and more efficient, yet in spite of the improvement it is estimated that less than 50 percent of the explosives used in industry today are ignited or detonated electrically. The trend, however, is toward the use of electric methods. In recent years numerous-mining companies have introduced electric blasting exclusively at their mines as a means of improving safety and efficiency."

Sep 1, 1946

By M. J. Ferrante

The Bureau of Mines recovered rhenium powder from scrap tungsten alloy containing approximately 25 percent rhenium. Oxidation of the scrap at 950° C separated volatile rhenium heptoxide from tungsten trioxide. Minor amounts of tungsten, iron, and nickel were removed by selective precipitation from a rhenium solution from which was recovered crystalline ammonium perrhenate. Experimentation showed that hydrogen reduction of minus 325-mesh ammonium perrhenate at 1,000° C produced rhenium powder averaging 2.1 microns in size (Fisher Sub-Sieve method). The powder contained <50 ppm of total metallic impurities and 1,070 ppm of total interstitial impurities. Sintered compacts had a density of 95 percent of theoretical. Approximately 96 percent of the rhenium contained in the scrap alloy was recovered.

Jan 1, 1969

By John R. Parker

Work places of an underground coal mine are required (30 CFR 1719) to be illuminated while self-propelled equipment is used. Permissible machine mounted systems have been developed and applied satisfactorily to many mining operations. However, some low seam and thin seam equipment has been difficult to illuminate because reliable, direct current systems and compact, low output, low glare luminaires were not available. This program resulted in the design and prototype construction of compact, low glare luminaires and AC and DC power systems, particularly suited to resolving illumination problems on low and thin seam mining equipment. Design objectives were based on enhancing the prospects for thin seam illumination solutions through definition of a product which could challenge markets enjoyed by higher glare luminaires and through reduction of technical risks associated with any new product development as well as the MSHA certification process.

Jan 1, 1982