Search Documents

By Edward L. McHugh

Digital camera and computer technologies can be used to monitor mine slopes and provide real-time warning of rock falls. NIOSH researchers assembled a surveillance system using low-cost video cameras and computer software from the security industry to test its effectiveness. The system is designed to signal an alarm when motion is detected and to record images of the scene. Masking can restrict motion detection to specific areas within the camera view; sensitivity is adjustable. The time-stamped images provide a record that can help reconstruct and quantify an event. Video motion detection can augment standard monitoring methods to increase safety in surface mines.

By L. A. Neumeier

The Bureau of Mines evaluated the properties of zinc alloys containing 25 to 40 wt pet Al and 0 to 0.7 pet Mg. Microstructures, hardness, and tensile properties were evaluated for material as extruded at 285° C, solution treated at 300° to 400° C, and subsequently aged at 100° to 200° C. The alloys without magnesium are characterized by low hardness and strength with high tensile elongation and reduction in area. It was verified that magnesium effectively retards the Zn-Al eutectoid transformation below 275° C and markedly increases hardness and strength with decreases in ductility. Solution treating at 350° C results in large grain sizes and gross embrittlement. Subsequent aging of the Zn-Al-Mg alloys at 200° C restores ductility substantially and stabilizes the structures, but strengths are considerably reduced. Combined strength and ductility properties are better for the as-extruded condition than for any heat-treated condition. There is usually little advantage in overall tensile properties from increasing magnesium above 0.1 pct.

Jan 1, 1971

By J. B. Gayle

Coke-pushing difficulties have been the subject of much controversy but relatively little scientific investigation. Nevertheless, continuing pushing difficulties can greatly decrease the life of a coke oven and should therefore be considered in the selection of the blend and operating conditions used for coke production. The present Federal Bureau of Mines investigation was undertaken to correlate results of previous investigators and to supplement these results to the limited extent practical by us of an experimental slot-type oven. To this end, pushing pressures have been determined routinely for Tuscaloosa oven tests conducted during the past 10 years. Nevertheless, the accumulated information remains incomplete in many respects, and in view of the recognized inadequacies of the data, publication is now undertaken only because of the scarcity of published information on this important problem and the discontinuation of carbonization studies with this oven.

Jan 1, 1961

By C. A. Herbert

During the fiscal year ended September 30, 1932, there were 27 fatalities in the coal mines of Indiana. Four of this number occurred in small mines employing less than 10 men, over which the State Inspection Department has no jurisdiction. In addition to these coal mine fatalities, an explosives accident in a clay mine resulted fatally to one man. Tables 1 and 2, which follow, list the fatalities as to cause and occupation. Table 1. - Fatal accidents by cause, fiscal year ended September 30, 1932 [ ]

Jan 1, 1933

By Gregory J. Chekan

As part of the initial investigation and validation of a new boundary-element formulation for stress modeling in coal mines, the underground stresses and displacements at two multiple-seam coal mines with unique stress problems were modeled and predicted. The new program, LAMODEL, calculates stresses and displacements at the seam level and at requested locations in the overburden or at the surface. Both linear elastic and nonlinear seam materials can be used, and surface effects, multiple seams, and multiple mining steps can be simulated. In order to most efficiently use LAMODEL for accurate stress prediction, the program is first calibrated to the site-specific geomechanics based on previously observed stress conditions at the mine. For this calibration process, a previously mined area is "stress mapped" by quantifying the observed pillar and strata behavior using a numerical rating system. Then, the site-specific mechanical properties in the model are adjusted to provide the best correlation between the predicted stresses and the observed underground stress rating. Once calibrated, the model is then used to predict future stress problems ahead of mining. At the two case study mines, the calibrated models showed good correlation with the observed stresses and also accurately predicted upcoming high stress areas for preventive action by the mines.

Jan 5, 1999

By Paul S. Schopf

The results of an experimental investigation into the possible use of medium energy acoustic fields (130 to 140 dB) to precipitate 1 to 10 micron particles is presented. The aerosol was produced with a LeMer generator using oleic acid and nitrogen. The sound field was a sinusoidal standing wave field in an acrylic tube, with light transmission data used for concentration determination. The results showed collection efficiencies of up to 80% on 2 micron particles with a residence time of 11.8 seconds at a sound pressure level of 139 dB re 2x10-5 N/m2. A discussion of the possible turbulent mechanism is made, as well as review and comparison with others? work.

Jan 1, 1972

To improve the level of hearing protection by providing workers with an inexpensive, easy-to-use device to check earplug fit. Background Approximately 30 million workers are exposed to hazardous noise on the job, placing them at risk of permanent hearing loss, tinnitus, and other disorders. Although the preferred solution is to eliminate noise through engineering controls or to reduce noise exposure through administrative controls, hearing protectors are critical when noise is unavoidable. Studies of hearing protector users have shown that average protection values in the real world are much lower than the labeled noise reduction ratings determined in laboratories with trained and motivated subjects. Even worse, many hearing pro­tector users get virtually no protection at all because of poor fit. The studies also show that users have a harder time achieving adequate protection levels with earplugs than with earmuffs. It?s difficult for users to tell if earplugs are working well just by looking at them. A more accurate approach is to check how much they block or ?attenuate? noise. Earplugs vary in their attenuation characteristics, with most providing a maximum of 20?35 decibels of noise reduction when worn correctly. Any earplug that?s suitable for use in noisy settings will attenuate noise by at least 15 decibels. Personal fit testing is an effective way to help hearing protector users improve the fit and protection levels of the devices. However, existing fit-testing systems are expensive and unsuitable for use at many industrial worksites.

Dec 1, 2008

By R. Duncan Gardner

This paper describing the mining practice at the Harmony mine, Baker, daho, is one of a series being prepared by the Bureau of Mines on mining practices, methods, and costs in the various mining districts in the United States. About 150 tons of copper ore containing 4 per cent copper, 0.001 ounce gold, and 0.1 ounce silver, is being produced daily from the Harmony mine by the shrinkage method of mining. The ore is taken by an aerial tramway 1/3 mile long to the mill, where it is concentrated. The concentrate is shipped 8 miles by truck to the railroad and thence by rail to Utah for smelting.

Jan 1, 1930

By Floyd G. Anderson

Bureau of Mines studies show than an electronic counter can be used for determining just concentrations from midget impinger samples collected in bituminous coal mines. A sample correlation coefficient of 0.91 for data obtained using the electronic counter and the Bureau of Mines microprojector procedures indicates a significant linear relationship between the methods. The electronic counter provides better counting precision and reduces analytical time.

Jan 1, 1968

By Mark R. Pettitt

Noise surveys conducted in underground coal mines have consistently indicated that auger mining machines subject the operator and helpers to excessive noise exposure. The machine cutting heads have been identified as the primary noise source. This report documents the research program conducted to (1) investigate the nature of the cutting head noise problem, (2) develop noise control concepts, (3) devise in-mine survivable techniques to implement the noise control concepts, and (4) build and demonstrate prototype reduced-noise auger miner cutting heads. The dynamic forces generated during coal cutting by the brittle fracture of coal are predominently low frequency. The low-frequency (less than 1500 Hz) structural response of the cutting head, therefore, determines the noise radiated by the cutting head. The most feasible methods of reducing the cutting head low-frequency response are to increase both the structural stiffness and the low-frequency damping. A technique was devised to achieve these goals. The standard plate helix was replaced by a sand-filled hollow helix of triangular cross section, and the core diameter was increased with an attendant reduction in helix depth. Extended in-mine tests demonstrated the operational capability of the reduced-noise auger cutting heads. The simple noise control concepts are valid for all continuous miner cutting heads. The sand-filled hollow helix technique, which achieved a 10 dB(A) noise reduction for the auger, can be used on any helix-bearing Cutting head.

Jan 1, 1983

By Alla D. Mah

The heat of formation of scandium sesquioxide (Sc203) has not been measured previously, and existing values for gallium sesquioxide (Ga203) are subject to large uncertainties. As a consequence, thermodynamic calculations involving these oxides hare lacked scientific exactness. This paper reports newly determined values of the heats of formation of gallium and scandium sesquioxides at 298.15° K., by combustion calorimetry. The corresponding free energies of formation are derived from heat and entropy data.

Jan 1, 1962

By J. R. Welty

High-temperature thermodynamic data have, in recent years, become increasingly important for the extractive metallurgist. The extraction of metals from their ores previously was based on trial and error methods, involving hours of testing and often costly equipment fabrication. Using thermodynamic data it is frequently possible to predict the feasibility of a proposed metallurgical process as well as the optimum operating conditions for the process with reasonable accuracy. Such predictions can save consider-able tim~ and expense. Widespread use of thermodynamic analyses has been handicapped by lack of dependable experimental data. Investigators, notably K. K. Kelley (4)4. have devoted many years to determining and compiling such data. These investigators, although prolific in their production of thermodynamic values, have been unable to meet all the needs of industry and other branches of science. This becomes obvious when one considers the aeronautical and nuclear fields, in which previously unimportant, therefore uninvestigated, substances have become of prime importance.

Jan 1, 1962

By R. W. Van Dolah

The feasibility of formulating cap-sensitive slurry explosives for use in underground mines with potentially flammable gas atmospheres was examined. Formulations containing aluminum metal as sensitizer and sodium chloride to reduce incendivity were prepared; some were cap-sensitive and had adequate air-gap. Flaked aluminum metal rather than the atomized type proved to be the more effective sensitizing agent of the formulations tested for incendivity in the large gallery of the Bureau of Mines, some were found to be suitably nonincendive.

Jan 1, 1968

By Susan E. Brink

The first step in determining whether Mn can be recovered by in situ leaching is to develop and test a selective lixiviant. Two column leach tests and one core leach test Were conducted by the U.S. Bureau of Mines on Mn oxide ore using aqueous sulfur dioxide (SO2) as the lixiviant. The column tests showed that aqueous S02 could selectively dissolve available Mn oxides from calcite-rich ore in a heap leach system. However, the core test showed that calcite gangue side reactions can have pronounced negative effects on the likelihood of successful in situ leaching of a calcite-rich ore with aqueous S02. Petrographic and geochemical analyses showed that both Mn (IV, III) oxides and calcite were dissolved. The abundance of dissolved Ca caused precipitation of gypsum. Acid consumption by calcite dissolution caused a rise in pH that caused the SO/S species to shift to S032-(sulfIte), which hindered reductive dissolution of Mn oxide. Gypsum precipitation did not affect complete leaching of the rock fragments in the column tests; however, it plugged the natural permeability in the core. Manganese recoveries were high for the column tests and low for the core test.

Jan 1, 2010

By A. F. Baker

Laboratory flotation of synthetic coal-pyrite mixtures and high-pyritic-sulfur coal indicated that ferric chloride (FeCl3), aluminum chloride (AIC13), chromium chloride (CrCl3), and cupric sulfate (CuSO4) are potential pyrite depressants. For each metal salt there appeared to be a range of pH values and optimum concentration for selectively depressing pyrite in coal flotation. Pyrite was depressed in the pH range from 4.5 to 7.0 with ferric chloride, from 5.8 to 7.0 with aluminum chloride, from 6.4 to 7.1 with chromium chloride, and from 6.4 to 7.4 with cupric sulfate. Best separation of pyrite from coal was achieved in flotation solutions containing from 2 X 10-5 to 5 x 10-5 mole/ liter of each salt. In solutions containing excess salt concentrations, coal was also depressed. These Bureau of Mines tests demonstrated on a laboratory scale that, in solutions containing 4 X 10-5 mole/liter ferric chloride and from 1 x 10-4 to 2 x 10-4 mole/liter sodium hydroxide, the pyritic sulfur content of a Lower Freeport bed coal sample could be reduced from about 2.51 percent to less than 0.60 percent with recoveries of over 83 percent. The depression of pyrite appears to be due to the adsorption of positively charged colloidal metal hydroxide at the pyrite-solution interface. This hypothesis is supported by zeta potential determinations which showed that suspended coal and pyrite particles in solutions containing metal salts are positively charged in the pH range where depression occurs.

Jan 1, 1971

By J. B. Gayle

The Bureau of Mines sole-heated oven has been used for studying coal expansion for some 20 years. During the period before 1940 emphasis was placed on studies of the mechanism of coal expansion and the effects of variations in operating conditions on the results. Since 1940 emphasis has shifted to a survey of the expansion properties of various coking coals. Because additional information concerning a number of unsolved problems in connection with the earlier studies appeared highly desirable, this investigation of the use of sole-heated ovens for studying coal expansion was undertaken. The principal findings, in order of their discussion in the text, may be summarized as follows. 1. Expansion results for binary blends of coking coals exhibit nonadditive behavior, both positive and negative deviations from additive behavior being noted, depending on the particular coals tested. Additive behavior can be achieved, however, either by charging the blend components in separate layers (which indicates that the observed phenomena are not characteristic of the particular expansion oven used) or by testing relatively coarse sizes of coal (which suggests that the effects of crushing on the expansion properties of coking coals may be even more complex than is generally recognized).

Jan 1, 1959

By Paul M. Tyler

One by one new metals come to share the burden of modern industry. Long before the Christian era potters and glass workers employed fine and costly blue pigments that contained cobalt. Cobalt blue class has been found in the tombs of the Egyptians and in the ruins of Troy, and many of the colors used by the ancient Greeks and Romans contained cobalt. The ancients, however, were apparently unaware that the colors they used were caused by cobalt, and it was not until late in the 17th century that the existence of the element was recognized, Writers in the Middle Ages referred to "cobalos" as an evil spirit that haunted mines and caused trouble to the miners. Subsequently the German worms "Kobold," meaning goblin, came to be applied to any baffling mineral and particularly to minerals that resembled ores but failed to yield metal when smelted. Even to-day there is something of an air of mystery about cobalt, and a medieval cloak of secrecy still surrounds many of the metallurgical processes employed in its production. "Zaffre" was mentioned about the middle of the sixteenth century by Biringuccio, and in 1735 the metal war, first prepared by G. Brandt. To preparation of cobalt compounds, however, must have been carried on in at least a small way ever since the opening of the silver-cobalt deposits of Schneeberg in 1470. By 1790 there were 25 works engaged in the industry, rust of them located in Saxony, but the total output of these works probably did not exceed 300 tone of cobalt annually, mostly in the fore of smalt. The smalt which contained approximately 6 per cent cobalt was sold in Venice in 1520 at about 16 cents a pound. A few refineries in Holland supplied the Irish linen trade, contributed a farce amount to the Dutch linen industries, and alto provided smaller quantities for the manufactuer of litmus in Holland. A complete description of the early [histor,] of the cobalt industry in Saxony, is given by Mickle in the Deport of the Bureau of Mines of Ontario, vol. 19, 1913, pt. 2, pp. 234-251.

Jan 1, 1930

By Robert M. Becker

The evaluation of existing rock stresses from measurements of the change in diameter of a borehole that is stress relieved by overcoring has become a common practice, The stress evaluation has been generally based ,on isotropic relations whereas rock in varying degrees is anisotropic. A plane elasticity solution for a circular hole along one axis of an orthotropic medium is adapted for evaluation of in situ stress from borehole deformation measurements. A consistent triaxial testing approach for determining elastic properties of the overcore is also outlined. Comparison of isotropic with anisotropic interpretations of the state of stress show that large errors in evaluation may occur if the anisotropic character of the rock is neglected.

Jan 1, 1967

By Martin Harper

This paper concludes a five year program on research into the use of a portable X ray fluorescence (XRF) analyzer for analyzing lead in air sampling filters from different industrial environments, including mining, manufacturing and recycling. The results from four of these environments have already been reported. The results from two additional metal processes are presented here. At both of these sites, lead was a minor component of the total airborne metals and interferences from other elements were minimal. Nevertheless, only results from the three sites where lead was the most abundant metal were used in the overall calculation of method accuracy. The XRF analyzer was used to interrogate the filters, which were then subjected to acid digestion and analysis by inductively coupled plasma optical emission spectroscopy (ICP OES). The filter samples were collected using different filter holders or "samplers" where the size (diameter), depth and homogeneity of aerosol deposit varied from sampler to sampler. The aerosol collection efficiencies of the samplers were expected to differ, especially for larger particles. The distribution of particles once having entered the sampler was also expected to differ between samplers. Samplers were paired to allow the between sampler variability to be addressed, and, in some cases, internal sampler wall deposits were evaluated and compared to the filter catch. It was found, rather surprisingly, that analysis of the filter deposits (by ICP OES) of all the samplers gave equivalent results. It was also found that deposits on some of the sampler walls, which in some protocols are considered part of the sample, could be significant in comparison to the filter deposit. If it is concluded that wall deposits should be analyzed, then XRF analysis of the filter can only give a minimum estimate of the concentration. Techniques for the statistical analysis of field data were also developed as part of this program and have been reported elsewhere. The results, based on data from the three workplaces where lead was the major element present in the samples, are summarized here. A limit of detection and a limit of quantitation are provided. Analysis of some samples using a second analyzer with a different X ray source technology indicated reasonable agreement for some metals (but this was not evaluated for lead). Provided it is only necessary to analyze the filters, most personal samplers will provide acceptable results when used with portable XRF analysis for lead around applicable limit values.

Jan 1, 2007

By E. G. King

An earlier Bureau of Mines report4 provided low-temperature heat-capacity and entropy data for three sodium vanadates. This report continues the study of vanadates by presenting analogous data for three crystalline calcium vanadates - calcium metavanadate (CaV206), calcium pyrovanadate (Ca2V2O7), and calcium orthovanadate (Ca3V208). No similar data for these compounds have been published previously. MATERIALS All three vanadate samples were prepared by the Bureau of Mines by heating stoichiometric mixtures of reagent-grade calcium carbonate and vanadium pentoxide.5 Calcium metavanadate was prepared at 610° to 660° C. A stoichiometric mixture was heated for 17 days with intervening grindings, mixings, and adjustments of composition, as shown necessary by chemical analysis. The final analysis gave calcium oxide, 23.48 pct. (theoretical, 23.57 pct.) and vanadium pentoxide, 76.32 pct. (theoretical, 76.43 pct.). The sample also contained 0.11 pct. acid-insoluble matter. The X-ray diffracton pattern showed no lines of free calcium or vanadium oxides. No X-ray diffraction patterns were found in the literature for any of these substances.

Jan 1, 1961