Search Documents

By J. A. Eisele

The Federal Bureau of Mines is engaged in a continuing program on the recovery of alumina from domestic source materials. Of the six processes being studied, current efforts focus on HCl leach of clays. A key step in the HCI process is the removal of iron from the aluminum chloride leach liquor. This was accomplished .by solvent extracting the iron with a tertiary amine in kerosine to which decanol was added as a phase modifier. In a mixer-settler operation, iron in the raffinate was reduced to <10 ppm in two extraction stages from a feed containing 1.4 gil Fe. Iron was stripped from the organic phase in three stages with dilute HCl.

Jan 1, 1976

By J. M. Goris

Cable bolt supports are becoming an important ground control technique in underground mines in the United States and Canada. They show great versatility and are adaptable for use with many mining techniques, they have high load-carrying capacities, they can be installed in small areas with low roots, and they are cost effective. Investigators in a number of research institutes in North America have conducted studies to assess the material and support properties of cable bolts, evaluate their support capabilities under various mining conditions, and provide design criteria for using cable bolt supports as roof control systems under varying mining conditions. While conducting these studies, personnel have collected important information on the history, application, performance, and economics of these supports. This U.S. Bureau of Mines report documents this information so that ground control personnel unfamiliar with cable bolt supports can gain an understanding and appreciation of their use. A comprehensive bibliography of technical information on cable bolt supports was selected by the authors and is also presented.

Jan 1, 1994

By Gerald T. Homce

Data from the U.S. Bureau of Labor Statistics show that 89 water well drillers died on the job between 1992 and 2002, and 28 of these deaths were electrocutions (Figure 1). In fact, elec­trical accidents are the leading on-the-job killer of water well drillers. The use of electricity is such an integral part of our lives that we usually take it for granted, but if we don?t understand or choose to ignore the hazards associated with electricity, the results can be deadly. Why is electrical shock so dangerous? If the voltage (of a shock) is sufficient to drive electrical current through your body, just 10 milliamps of cur­rent (1000 milliamps = 1 amp) can cause muscles to contract and prevent you from releasing an energized wire or tool in your grip. As little as 30 milliamps of current can paralyze your breathing, and 75 milli­amps can cause your heart to stop pumping blood (ventricular fibrillation). As a comparison, a small bedroom night-light draws about 30 to 60 milliamps. Other factors influence how severely you?ll be shocked if you touch a live electrical circuit, such as the path electrical current takes through your body and how long it flows, as well as your body weight. How much voltage is needed to drive electrical cur­rent through your body? Not much! Generally, any power source at 50 volts AC or higher is considered dangerous.

Jan 1, 2008

By W. C. Holliman

This report on the characteristics of commercial aviation gasolines is one of a series of such reports. It presents compilations of&apos; inspection data furnished on their products by 15 manufacturers of commercial grades of aviation gasoline and special data obtained in Bureau of Mines laboratories on 68 samples of these gasolines. Data are presented for 18 samples of grade 80, 20 of grade 91/98, 21 of grade100/130, and 9 of grade 115/145 aviation fuels. The gasolines are designated January 1948 production, although some of the samples actually were produced at a later date.

Jan 1, 1948

By J. W. Sterner

The Bureau of Mines conducted studies on four makes of Japanese automobiles, three 1981 and one 1982 model years, received from three manufacturers to determine if their materials composition would present problems to the current technology used to process junk automobiles for metal recovery. One of each make of automobile was hand-dismantled to determine the materials composition. In addition, two nearly identical automobiles of each make were shredded at a commercial operation where all metal products and rejects were collected for analysis to determine metal and nonmetal distribution. The average weight of the four automobiles to be dismantled, less batteries, tools, and fluids, was 1,938.3 lb. The weight was distributed as 1,472.9 lb. ferrous and 115.6 lb nonferrous metals, 275.2 lb combustibles, 72.3 lb noncombustibles, and 2.3 lb electrical components. The dismantled automobiles, less gas tanks, fluids, tools, wheels, tires, and batteries, which were all removed from the automobiles that were shredded, contained an average of 1,389.1 lb ferrous and 101.6 lb nonferrous metals, 305.7 lb nonmetals, and 2.3 lb electrical components. In comparison, materials collected from the shredded automobiles averaged 1,304 lb ferrous metals, 80 lb nonferrous metals, and 341 lb landfill materials. There were no materials used in the manufacture of the late model Japanese automobiles that should present handling or processing problems to the steelmaking or secondary metal recyclers.

Jan 1, 1984

By Liming Yuan, Charles D. Litton

This paper presents experimental results for conveyor belt flame spread from tests conducted in a small-scale tunnel. The purpose of this study is to investigate the effects of belt type, ventilation velocity, belt surface-to-roof distance and ignition source power on the flame spread properties. The tunnel used was 4.9 m long by 0.46 m square with the ventilation velocity ranging from 0.7 to 3.2 m/s. The ignition source was an impinged methane jet burner with heat output ranging from 7 to 21 kW. The belts tested included non-fire resistant rubber belts, fire-resistant rubber belts, fire-resistant neoprene belt and fire-resistant PVC belt with belt samples measuring 0.23 m wide by 2.5 m long. Experimental results show that with a ventilation velocity of 1.02 m/s all conveyor belts could be ignited, and that with sufficient ignition source power, flames spread the full length of the belt sample. The data showed a coupling effect of the ventilation air velocity and the belt surface-to-roof distance on the flame spread rate. For instance, flames could not spread with a ventilation velocity higher than 1.52 m/s and a surface-to-roof distance of 0.22 m. The use of the measured CO/CO2 ratio as an indicator of combustion stoichiometry is also discussed.

By James W. Miller

An investigation was begun by the Bureau of Mines in 1948 to determine the preparation characteristics of American coals. Results of the investigation were planned to be reported on a county basis and from the data developed, to determine: (a) Which coals either as mined or after beneficiation by conventional preparation are chemically suitable under present standards for producing metallurgical coke; (b) Which coals require special and more intensive treatment in preparation than is now practiced; and (c) Which coals cannot be considered potential sources of metallurgical coke, regardless of preparation. This report is one in this county series that describes the preparation characteristics of the coals of Perry County, Ky.

Jan 1, 1956

By N. P. Kripakov

The Bureau of Mines has developed a unique new mine design procedure to determine the changing static load distributions imposed on under-ground support structures during the mining cycle. The procedure reduces the complexities associated with analyzing a three-dimensional problem. A combination of the multiple-seam displacement-discontinuity model and a two-dimensional finite-element window model produces refined results for a specific area of interest by assuming displacement compat-ibility between models. Input to the procedure includes the geometry of mined-out areas in up to two adjacent seams, the rock mass characteris-tics of the surrounding geology, the in situ stress conditions, and the mining sequence. The displacement-discontinuity program calculates ex-pected loadings for mine structures affected by the mining cycle and/or by overlying or underlying seams. Pseudoelastic finite-element analysis using a yield-factor approach determines the stability of coal pillars by simulating the degree and extent of nrogressive rib failure and sub-sequent load transfer. Application of the procedure is demonstrated on a field problem. In-duced stress changes predicted from the numerical model analysis are in reasonably good agreement with stress measurements obtained from an instrumented chain pillar affected by remnant workings in an upper seam.

Jan 1, 1988

By Jon C. Volkwein

The Bureau of Mines, Foster-Miller Inc., and Beaver Creek Coal Co. have evaluated the ability of a new system to ventilate a 40-ft-deep cut. A remote-control continuous-mining machine, in a 7-ft-thick seam, with exhausting brattice was fitted with an improved sprayfan system plus additional forward and reverse pointing sprays. Static and dynamic tests using tracer gas were conducted in a full-scale model and under-ground to measure the effectiveness of exhaust face ventilation for various deep-cutting mine and spray configurations. When compared to a lO-ft primary ventilation brattice, the extended-cut spray system consistently provided better face ventilation at all configurations up to and including a 40-ft brattice setback. The system also provided good dust protection and visibility for the machine operator. Another safety advantage is the elimination of the need to set temporary roof supports to maintain the ventilation brattice.

Jan 1, 1985

By Lewis M. McNay

Description of methods employed and cost data are given for surface-mined land reclamation in Moraine State Park, Butler County, Pa. This project was conducted under the authority of the Appalachian Regional Development Act; a total of 177 acres of land was rehabilitated for specific land use purposes. The use of large equipment expedited the project work, and similar results could be anticipated on similar reclamation programs.

Jan 1, 1970

Lower the respirable dust expo? sure of longwall shearer operators Approach Use improved water sprays on the shearer machine to direct the dusty air toward the face. In laboratory tests and actual mining conditions, the shearer-clearer has proved to be an effective dust control technique. Recent field experience however, has indicated that not enough technical information is available on proper installation of the improved shearer-clearer. This Technology News will provide details of the Improvements made to the shearer-clearer and provide guidelines for installing the system. How It Works The shearer-clearer system consists of several strategically-mounted water sprays and one or more passive barriers. The sprays redirect the airflow around the shearer into both a clean and a contaminated split. The sprays confine the contaminated split or dust cloud to the coal face, allowing the shearer operators to remain in the clean split on the walkway

Jan 1, 1986

By Frank L. Hess

Vanadium, although widely spread in minute quantities through the crust of the earth, is found in few places sufficiently concentrated to be economically mined and prepared for use. Most rocks carry from a trace to a few hundredths of a per cent of vanadium oxide, and coal ash may carry about as much as the rocks, Much of the "coal" quoted in the literature as carrying vanadium has been asphaltite, and in other ccal the vanadium is of late introduction. The ash of the petroleums, though usually present in very small quantity, may carry a large percentage of vanadiun, so that production of vanadium from it has been seriously considered. Naturally the ashes of soze asphaltites similarly carry vanadium.' The great deposit at Minasragra, Peru, to which further reference will be made, is probably an altered asphaltite. Ilmenite and cther iron minerals usually carry vanadium 10 and some has been saved from the minette ores of France. 11 Many veins that carry lead copper and zinc minerals also carry a little vanadium, which, especially if the veins are in a comparatively dry region, such as the southwestern United States, northern Mexico, Northern Rhodesia, Southwest Africa, or Spain, collects in the oxidized parts of the veins as vanadinite,

Apr 1, 1932

By H. S. Caldwell

Molten zinc, condensed from zinc vapor, was used by the Federal Bureau of Mines to leach aluminum from an aluminum-silicon alloy made by carbothermic reduction of silicious aluminum ores. Zinc requirements were minimized by re-fluxing condensed zinc in a low-pressure, Soxhlet-type distillation unit. The minimum ratio of zinc used to aluminum in the crude alloy was approximately 2:1. When the system pressure was reduced from atmospheric pressure to 100 microns or less, the rate of aluminum extraction increased by a factor of 20. Leaching rates were much higher when the zinc vapor was condensed directly on the crude alloy than when molten zinc was passed over the alloy in the absence of appreciable zinc vapors. Observations indicated higher extraction efficiencies from crude alloys containing greater amounts of iron. Complete extraction was obtained with negligible loss of zinc. Assuming complete removal of zinc, the aluminum products will contain 1 to 6 percent silicon and about 0.5 percent iron plus titanium. The leached crude-alloy residue is a highly friable spongelike material containing about 80 percent silicon, several percent iron and titanium, with the remainder aluminum. This extraction method has been patented (Patent 2,810,637) and assigned to the Government. Research and development investigations are continuing at the College Park Metallurgy Research Center.

Jan 1, 1961

By William C. Larson

A study was conducted by the Bureau of Mines to provide quarry operators with information regarding (1) the effects of jointing and bedding on rock fragmentation when bench blasting in two small-scale (2.5-ft) limestone benches, and (2) the successful use of inexpensive equipment and field techniques to determine the orientation and spacing of joints and bedding separations within the quarry. Using inexpensive equipment, such as a pocket transit and steel and paper tapes, joint and bedding separations were mapped and their frequencies measured. Results from two small-scale bench blasts in the Stewartville member of the Galena limestone formation showed that when the row of vertical blast-holes was oblique to the vertical joint orientations, the backface expression was outlined by two relatively large triangular protrusions (joint surfaces). In this blast, part of the rock burden was unbroken. When the line of vertical blastholes paralleled a predominant joint set, all of the rock burden was broken and displaced. The thickness of fragments that had been displaced by a blast correlated with the observed bedding thickness in the bench.

Jan 1, 1974

By E. G. King

THIRD-LAW entropy data for zirconium-containing compounds are sparse. Kelley a lists entropies at 298° K. for the oxide, tetrachloride, nitride, and silicate, as well as for the metal. The present paper presents heat capacities between 51° and 298° K. and entropies at 298.15° K. for the zirconates of the alkaline-earth metals-calcium, strontium, and barium. The authors believe magnesium zirconate does not exist as a stable compound at room temperature. Entropies of formation from the constituent oxides also are given. MATERIALS The materials used in this investigation were synthesized and analyzed in the Berkeley Laboratory of the Bureau of Mines. Calcium zirconate was prepared by heating an intimate mixture of reagent-grade calcium carbonate and pure zirconia for 30 hours between 1,200° and 1,300° C. and for 32 hours between 1,400° and 1,500° C. As part of the heating schedule, the sample was ground and mixed seven times. Periodic analyses and minor adjustments of composition were made. Analysis of the final product gave 31.19 percent calcium oxide (theoretically 31.28 percent) and 68.67 percent zirconia (theoretically 68.72 percent). The X-ray diffraction pattern agreed with that in the ASTM catalog.

Jan 1, 1960

By T. L. Muldoon

The bagging of dry pulverized products using fluidized air packers creates severe respirable dust problems in many surface mining operations. During bag filling, excess air and product blows by the bag valve/nozzle interface. After bag ejection, dust blows out of the bag valve. During conveying and handling dust is released from the bag valve and dirty bag surface. Overexposure of the bagging machine operator and bag handlers is common. This report describes the development and testing of a new dust control system for bagging machines. The system features a new bag clamp design to reduce product blowby during filling. A controlled vacuum system removes excess air from the bag before ejection, eliminating the problems after bag ejection and during conveying and handling. The system has shown significant reductions in dust exposure for both bag machine operators and bag handlers. These reductions are achieved with no significant effect on total mill productivity.

Jan 1, 1985

By Thomas R. Bur

The patterns of variation of the 21 anisotropic elastic constants with direction arc presented for all of the symmetry systems that are normally expected to occur in rocks and in the constituent minerals. The exception, which is not discussed, is the triclinic system for which no elastic constants are available. Variations are shown for rotations about the principal axes by means of polar graphs. These include graphs for all of the n-fold symmetry axes possible for elastic symmetry and thus make it possible to visualize variational patterns for rotations about any n-fold axis. Variations throughout space are shown by means of equal area projections for the only constants (those relating axial stress to axial strain) that are uniquely defined by a single closed surface. For those unfamiliar with the compliance (Sij) and stiffness (cij) coefficients, the variations that can be shown by Young&apos;s modulus (E), Poisson&apos;s ratio (v), and shear modulus (G) are also given.

Jan 1, 2012

By Robert F. Droullard

The Bureau of Mines has investigated techniques of using gross alpha or beta detectors to continuously measure working levels. Both methods measure radioactive particulates collected on a filter paper using a constant airflow. Inherent-error studies indicate a value of about ±3 percent for the gross alpha method and about ±8 percent for the beta method in typical mine atmospheres. However, the beta method avoids problems associated with alpha detectors and is therefore more useful. Applications of these continuous working-level detectors include work area monitoring of exposure levels in underground openings, such as mines and caves, and calibrating personal dosimeters exposed over extended time intervals.

Jan 1, 1977

By Michael J. Friedel

As part of an investigation aimed at improving the health and safety and competitiveness of the mining industry, the U.S. Bureau of Mines evaluated the application of common offset radar profiling, using a 250-MHz ground-penetrating radar (GPR) system, for the detection of fractures in igneous rock. A series of radar reflection surveys were conducted to detect and delineate the extent of fracturing at various granodiorite and gabbro quarries and outcrops located in Minnesota. The application of radar profiling for detecting joints, sheeting fractures, shear zones, and depth to water table was demonstrated to be feasible with minimal processing. Radar reflection interpretations were verified by visual inspection of the rock mass and field mapping of local structure. The radar reflection section provides a simple, rapid, and cost-effective means for mapping of shallow (less than 10 m) small-scale fractures (greater than 0.25 cm) in igneous rock masses (characteristic of velocities between 0.061 m/ns for gabbro and 0.125 m/ns for granodiorite). Depth or distance estimates to fractures are within 10 pct of the actual, and time-shift compensation is necessary only when topographic irregularities exceed 30 cm.

Jan 1, 2010

By Isaac A. Zlochower, Michael J. Sapko, Eric S. Weiss, Kenneth L. Cashdollar

This paper describes dust explosion research conducted in an experimental mine and in a 20-L laboratory chamber at the Pittsburgh Research Laboratory (PRL) of the National Institute for Occupational Safety and Health (NIOSH). The primary purpose of this research is to improve safety in mining, but the data are also useful to other industries that manufacture, process, or use combustible dusts. Explosion characteristics such as the minimum explosible concentration and the rock dust inerting requirements were measured for various combustible dusts from the mining industries. These dusts included bituminous coats, gilsonite, oil shales, and sulfide ores. The full-scale tests were conducted in the Lake Lynn experimental mine of NIOSH. The mine tests were initiated by a methane-air explosion at the face (closed end) that both entrained and ignited the dust. The laboratory-scale tests were conducted in the 20-L chamber using ignitors of various energies. One purpose of the laboratory and mine comparison is to determine the conditions under which the laboratory tests best simulate the full-scale tests. The results of this research showed relatively good agreement between the laboratory and the large-scale tests in determining explosion limits. Full-scale experiments in the experimental mine were also conducted to evaluate the explosion resistance characteristics of seals that are used to separate non-ventilated, inactive workings from active workings of a mine. Results of these explosion tests show significant increases in explosion overpressure due to added coal dust and indications of pressure piling.