Search Documents

By Charles F. Weber

Premature blasts of charges of explosives have caused many deaths in anthracite mines, and the causes of many of the blasts were not determined satisfactorily. Investigators often found fairly high potential differences between such metallic objects as rails, pipes, conveyor lines, or sheet-iron chutes in the working place where an accident had occurred. At one mine where a premature blast occurred in a rock tunnel, one workman was killed and two others were injured, and several days later a potential difference large enough to explode an electric squib was detected between the compressed-air pipe and the track rail; the voltage fluctuated and appeared to change with the movement of a locomotive. At another mine, a. workman was killed when a primed cartridge that he was about to load in a blast hole exploded in his hand. During the investigation, a potential difference was found between the conveyor line and the sheet-iron chute. During a 5-year Period, 61 fatalities and 771 nonfatal injuries were caused by explosives accidents in anthracite mines, and one of the chief causes of these accidents was premature blasts.

Jan 1, 1950

By Jack Wasserman, Don Wasserman, Gretchen Hinton, Logan Mullinix, Shekar Khanal

Human testing has always been a needed way to provide information on the effects of vehicle vibration, however, the manner of testing has not reflected the real situations of driver’s hands on a steering wheel and a seat with back support and driving tasks. The typical system have used a standard sinusoidal excitation rather than the typical types of road – truck excitations The new truck driver training simulators provide the combination of road roughness, speed effects, cab environment and individual tasks. The system has a full six axis simulation potential. The simulators have the protection of the individual by a combination of two ways for the individual to stop the motion as well as an operator with visual capability who can stop the testing. The closed simulator, shown in Figure 1, has the potential for providing motion during the operation.

Jan 6, 2006

By Clete R. Stephan, Mark J. Schultz, William A. Slivensky, Eric S. Weiss, Kenneth W. Jackson

he Pittsburgh Research Center (PRC)~ and the Mine Safety and Health Administration (MSHA) are participating in a research program to evaluate the strength characteristics and air leakage resistance of seals and water trap designs for use in underground coal mines. This program is being conducted at PRC's Lake Lynn Laboratory near Fairchance, Fayette County, PA. Seals designed with a 40-cm-thick polymer (polyurethane) and aggregate core between two dry-stacked (no mortar) concrete block walls (coated on out by sides) withstood a 138-kPa pressure pulse while maintaining acceptable air leakage rates. Similar seal designs utilizing a 97-cm-thick, 91-kg/m7-density, polymer-only core did not survive; however, a 5 1 -cm-thick, 203-kg/mi-density, polymer-only core seal successfully withstood the explosion pressures. Evaluations of cellular concrete seal designs have shown that a two-pour slurry injection technique did not adversely affect the strength of the 1.2-m-thick seals when subjected to a 138-kPa pressure pulse. Two seal designs utilizing low-density cementitious block have also been evaluated with successful results. In addition to seal strength tests, various 15- and 30-cm-diam U-shaped water trap pipes and a water trough design were evaluated under explosion conditions and were shown to be inadequate when evaluated under worst-case conditions. Simple modifications to the various water trap designs were successfu1 in preventing the passage of explosion flame through the trap.

Jan 4, 1996

By Vance G. Leak

A technique for recovering copper and steel from metallic scrap has been developed by the Bureau of Mines based on preferential melting in molten salt baths at 1,150° to 1,250° C, The molten salt, preferably barium chloride or calcium chloride, both minimizes oxidation of the metals and promotes heat transfer. Cleanest separations (0.01 percent copper remaining in iron) have been achieved by pretreatment (dipping or spraying) with sodium sulphate or sodium silicate, which alters and coats the surface of the iron to inhibit the alloying or brazing with copper. An economic evaluation of the process was carried out on six combinations of sweating media and inhibiting reagents. On the basis of the postulated model, a cost of about $0.20 per pound of copper recovered has been determined for the sweating treatment operation.

Jan 1, 1973

By Irving Hartmann

When permissible explosives are used in coal mines according to the procedure recommended by the Bureau of Mines they are relatively safe, and no mine explosions are known to have resulted from this type of blasting. However, unsafe blasting practices - the use of nonpermissible explosives or the improper use of permissible explosives - have caused many serious disasters. In fact, such unsafe practices constitute the third most important cause (exceeded only by electricity and the use of open lights and smoking) of coal-mine explosions in the United States. During 1929-1947, inclusive, 81 explosions, resulting in 475 fatalities, were ascribed to unsafe blasting. The hazards of black powder, dynamite, and other nonpermissible explosives in coal mines have been recognized for many years, and attention has been called to this in numerous Bureau of Mines publications. Not only can these explosives ignite namable gas-air mixtures readily, but they can also ignite coal dust, as has been illustrated repeatedly in tests and at educational public demonstrations at Bruceton and elsewhere.

Jan 1, 1952

By J. E. Murphy

Purification of samarium metal by sublimation and by vaporization from a low-melting metal flux, at the same temperature, were compared. Vaporization proved more effective for removing impurities such as magnesium, calcium, and manganese. Recovery of samarium, however, is more rapid by sublimation because of its constant rate of distillation.

Jan 1, 1970

By N. A. Gokcen

This Bureau of Mines report reviews and summarizes recent studies of the rates of chlorination of aluminous resources with CO and C12 mixtures with and without COC12. No reaction mechanism could be obtained from the existing results; however, diffusional barriers in the gas and solid layers probably control the chlorination rate in thermogravimetric experiments. Fluidized beds of particles smaller than 0.1 mm appeared to show very little solid layer diffusional barrier. For optimum chlorination the particle size should probably be less than 8 mm, the calcination temperature approximately 700° C, and the chlorination temperature from 650° to 750° C. Relatively rapid chlorination with COC12 in thermogravimetric experiments was attributed partly to the simultaneous supply of reductant and chlorinator by one gas to the sample reaction site. Comparable results for chlorination of fluidized beds with COC12 are not available. Equimolar mixtures of CO and C12 produced the optimum rate of reaction. Addition to the calcine of 10 to 20 wt-pct NaCl accelerated the rate of chlorination, and addition of SiC14 to the gas mixture decreased the rate of chlorination of SiO2 drastically, but at the expense of chlorination of significant fractions of Al2O3. Further research in various areas is suggested.

Jan 1, 1983

By Robert L. Lappi

Volume I of this report described the demonstration of cross-ridge mountaintop coal mining. This document, Volume II, is intended for use as a supporting document to Volume I. This report describes the MATHMINE Mine Simulation System, a modularized software system used to support the demonstration of cross-ridge Mountaintop coal mining. The MATHMINE Mine Simulation System was used to generate mine plans for coal extraction at lowest cost. The functional details, data requirements and output of the software system are detailed here. The computer program was written in FORTRAN. One module which generates resource location data required the use of SAS?.

Jan 1, 1984

By Raghoottma S. Pandurangi, Mohindar S. Seehra

"The interaction of amorphous 1ilica particles with several hydrogen bonding agents (H2O, C2H5OH, C7H2NO) was investigated by monitoring the changes in the bulk and surface IR vibrational modes of silica using photoacoustic spectroscopy. It is argued that the intensity of the silanol band at 3747 cm-1 provides (an inverse) quantitative measure of the interaction or surface groups, along with the shift in the broad hydroxyl band, the interaction following the order C7H2NO > C2H5OH > H2O. Index Headings: Silica; Surface vibrational modes; Photoacoustic spectroscopy; Hydrogen bonding agents.INTRODUCTIONThe use of m spectroscopy to study the adsorption on solid surfaces is well documented in the literature.1 2 For example, hydroxylation of a clean silica surface results in the formation of the free silanol group Si-OH, with a sharp IR band near 3747 cm-1• Further hydroxylation produces a broad band near 3500 cm-1, which is believed to result from various hydrogen-bonded silanol bands leading to a multilayered surface structure of few nm.3-5 Earlier studies had indicated a relationship between the surface silanol band and various chemical activities of silica such as cytotoxicity, 7- 9 catalysis, 10-12 and others.13 Recent studies from our group14-in which the intensity of the silanol band and cytotoxicity of silica, heat-treated at various temperatures up to 1095°C, were investigated have provided a strong correlation between cytotoxicity and intensity of the silanol band.Coating of silica by PVPNO (polyvinyl-2-pyridine N-oxide with the empirical formula C7H8NO), a strong hydrogen bonding agent, is known to reduce the cytotoxicity of silica, presumably by chemically blocking the silanol groups from phospholipids.15 This interaction of the hydrogen bonding agents with the silica can be studied by m spectroscopy, and Knozinger16 and Rouxlet and Semples11 have used transmission m spectroscopy to study the effect of various chemicals on the surface IR modes of silica. However, one of the major disadvantages of transmission IR spectroscopy is that the sample preparation (grinding and mixing with KBr and pelletizing) usually distorts the surface modes (see, e.g., Ref. 14) and there is always a doubt about the effect of the sample preparation on the measured properties. In recent years, photoacoustic (PA) spectroscopy has become the technique of choice for studying the IR spectra of samples in their natural state, since no sample preparation is necessary.18•19 Moreover, according to a recent paper, 20 the relative intensity of the surface modes in PA spectroscopy of silica particles is much higher than that in transmission FT-IR spectroscopy. Consequently PA spectroscopy is ideal for studying the surface chemistry. In this work, we have used PA spectroscopy to investigate the interaction of three hydrogen bonding agents (C7H8NO, C2H50H, and H20) with the silica surface by monitoring changes in the surface m modes. Our results show that the surface IR modes get perturbed to a larger extent than the bulk IR modes in interaction with the hydrogen bonding agents. Moreover, whereas in the earlier studies, the shift of the broad silanol band near 3500 cm-1 was used as a measure of the interaction with hydrogen bonding agents,16•17 here we show that the relative decrease in the intensity of the sharp silanol band near 3747 cm-1 also serves as a quantitative parameter for the relative surface coverage and surface modification. Details of this work are given below."

Jan 1, 1990

By W. C. Hudson

"The McLeod sand pits, on the northeast side of the Little Ocmulgee River in Wheeler County, Ga., opposite Lumber City in Telfair Co., were examined by the Bureau of Mines under its war program of Investigation of Critical and Essential Minerals. The pits are about a quarter of a mile above the bridge, which is half a mile above Lumber City. Mrs. A. T. McLeod of Lumber City owns the land, including the pits. The property was inspected by an engineer of the Bureau of nines on March 8, 1945, on recommendation of Capt. Garland Peyton, director, Division of nines, Mining, and Geology of Georgia.The Mcleod pits are at the northwestern extremity of a mile-long series of old pits that were worked from about 1900 until the 1920's. The burning of the spur railroad bridge connecting the pits with the Southern Railway at Lumber City stopped mining operations. The pits on the south-east, or opposite, side of the Glennwood Road from the McLeod pits were first worked by F. L. Hinson and later, in 1921, by Mrs. n. H. Mobley. The glass sand was shipped to Tallapoosa, Ga., and Chattanooga, Tenn., where it was used in the manufacture of bottles for soft drinks. Some of the sand was used as molding and construction material. The sand was mined by hand shoveling it into wheelbarrows, which were unloaded on freight cars. The pits were partly refilled with overburden, so that it is impossible to estimate even roughly the amount of sand excavated.Analyses of samples of glass sand made years age3/ and later in 19404/ roughly check those made by the Bureau of Mines laboratory, except that in the former the iron oxide content usually was greater, attaining a maximum of 0.72 percent.The sand pits are in a valley slightly more than a quarter of a mile wide that lies along the northeast side of the Little Ocmulgee River. The land is either flat or marked by ridges only a few feet high. . A rather thick growth of scrub trees covers most of the valley. The surrounding country consists of gently rolling farm lands. The altitude of the valley is not known, but, judging by its distance from the seashore, it probably is about 200 feet. In addition to the Glennwood highway, which crosses the valley, several old sand roads lead to the pits."

Apr 1, 1946

By Laxman S. Sundae

A U.S. Bureau of Mines designed and fabricated in-seam tester (1ST), retrofitted with a dust shroud, was used to establish a respirable dust index (RDI) and to determine cutting forces from a variety of bit types in four coal mines and a salt mine. Results from cutting tests at four coal mines showed that radial bits required the lowest cutting force and the least specific energy. Generally, for each conical bit the RDI and cutting force increased when the included bit tip angles increased from 70° to 90°. During field tests it was not possible to measure the total quantity of respirable dust produced by each cut; therefore, attempts were made to determine the amount of dust that became airborne from each test cut. The test results show that the quantity of airborne respirable dust is very erratic and cannot be related to bit type. Two statistical methods were employed to analyze RDI, but no correlation was found between the RDI and bit type. Despite scatter in test results for RDI, significant difference was found in RDI generated in four coal seams. In general, RDI increased with the increased cutting force for each coal seam from mine 1 through mine 4.

Jan 1, 1989

By Richard C. Rice

Laboratory and field data for wire ropes typical of constructions used in underground mine hoisting were obtained, screened, encoded and analyzed statistically. The statistical analysis of data for hoist ropes retired from service showed that rope remaining strength (or, conversely, strength loss) can be predicted with good accuracy if several nondestructive measures of rope damage are assessed. Found to be most important was the outer-wire corrosion rating, the electromagnetic (EM) nondestructive-inspection technique used for predicting strength loss, and the rope diameter reduction. Signs of rope deterioration such as broken wires or damage were also important indicators of strength loss. Based on the results of this investigation, a number of recommendations are presented that promise to yield better rope inspection and retirement criteria which will in turn lead to improved safety and efficiency in underground mine-hoist systems.

Jan 1, 1983

By W. S. Landers

In contrast to the large fund of information available on the carbonizing properties of Eastern U.S. coals, the experimental data available for most Western U.S. and foreign coals are meager. To supply some self-consistent data, the Bureau of Mines conducted 220 low-temperature carbonization assay tests at 500° C. in a laboratory-scale carbonization apparatus. The results are included in this report. The U.S. coals tested are from Alaska, Arizona, Colorado, Illinois, Montana, New Mexico, North Dakota, Pennsylvania, Ohio, Texas, Utah, and Wyoming. Assays were also made on coals from Canada, Ecuador, France, Greece, India, Mexico, the Philippine Islands, Thailand, and Yugoslavia. In addition, one assay of pine sawdust and one assay of a peat from Ireland are reported. Prediction equations were developed relating the yield of products of carbonization obtained at 500° C. in the assay unit to the proximate and ultimate analyses of the coals. The equations for predicting the yields of tar plus light oil, char, and gas, and the heating value of the gas, are considered good, each equation having a multiple correlation coefficient of 0.90 or higher. The equation predicting volume of gas obtained upon carbonization is considered as fair, with a multiple correlation coefficient of 0.84. A reproducibility study of the assay made on 10 replicate samples of a subbituminous coal indicated that the standard deviation of the individual products was 0.31 percent or less.

Jan 1, 1961

By C. K. Man

Coal dust explosions are routinely conducted within the full-scale experimental mine at the National Institute for Occupational Safety and Health (NIOSH), Pittsburgh Research Laboratory?s (PRL) Lake Lynn Experimental Mine (LLEM) to meet the needs of numerous safety and health research programs. Many of these explosion tests over the years involved igniting different coal dust and limestone rock dust mixtures (up to 80% by volume rock dust). Following four more recent tests, floor dust samples have been collected and analyzed using the alcohol coking test and scanning electron microscopy (SEM) and the results compared to estimate the flame travel.

Jan 1, 2009

By Jeanne A. Zimmer, Brad Smith, Steve Viles, Andrew B. Cecala

A recent report evaluating silica exposure levels in the metal/nonmetal mining industry noted that bag packaging and loading are some of the occupations at the greatest risk. In addition to dust problems, the bag-stacking process is labor intensive, making lost-time injuries common due to back fatigue and strains. During the bag-stacking process, a significant amount of dust can be generated, mainly from product on the outside of the bags and from dust escaping the bag valve upon impact of the bag on the pallet. In an effort to address dust-exposure and back-fatigue issues, Malvern Minerals Co., Hot Springs, Ark., made two major improvements to its ground silica stacking facility. First, the company purchased a semi-automated bag palletizing system (Figure 1). With this system, the bag stacker does not lift the bags, but slides them across a metal table. Small jets of air exit through perforations in the table top (similar to an air hockey game), allowing workers to more easily slide each bag into the proper position. After each layer of bags is completed, the table slides open, and the entire layer of bags is loaded onto an underlying pallet. The table then closes, readying it for another layer of bags. After the entire pallet is loaded, the unit delivers the pallet to a shrink wrap and forklift pick-up area. In addition to this semi-automated palletizing unit, Malvern Minerals purchased an Overhead Air Supply Island System (OASIS) to lower the bag stacker's dust exposure. The OASIS takes outside air, directs it through MEASURING RESPIRABLE DUST The bag stacker's respirable dust exposure was monitored using a RAM-1 instantaneous dust monitor to evaluate the impact of the various changes on the palletizing process and dust-control equipment. The bag stacker wore a vest that held the 10-mm Dorr-Oliver cyclone, which classifies the respirable portion of dust. Flexible tygon tubing was used to connect the cyclone to the RAM-1 dust unit, allowing the bag stacker to perform the palletizing process with minimal interference. The RAM-1 measures respirable dust concentrations by light scattering with a sensing chamber. This device closely simulates gravimetric measurements when calibrated for a specific dust. This instrument is ideal for comparative evaluations, as was the case in this study. Since the RAM-1 is not an MSHA-approved instru¬ment for dust compliance sampling, the dust concen¬trations listed in this article should be used as a com¬parative value of respirable dust concentration and not to determine actual dust concentrations from a com¬pliance standpoint.

By Philip E. Sanker

The Bureau of Mines conducted small-scale batch and semicontinuous tests on the reduction of zinc sulfide with iron according to the reaction ZnS + Fe ? FeS + Zn to determine reaction kinetics in the temperature range 1,000° to 1,400° C and to investigate the potential use of a scrap iron reductant. Batch tests indicated that a temperature of at least 1,300° C with a 1:1 mole ratio of Fe to ZnS is needed for good zinc recovery. Semicontinuous tests were conducted, using four zinc concentrate samples, containing various percentages of copper, cadmium, and lead, which were reacted with iron and iron contaminated with iron oxide and tin in an externally heated graphite furnace. Analysis of the zinc metal and FeS matte reaction products showed cadmium to be entirely in the zinc metal, copper to be in the FeS matte, and lead to be about 60 pct in the zinc metal and 40 pct in the matte. Tin reported to the matte, and none was detected above the O.OS-pct level in the zinc. Sulfur dioxide was not detected in the offgas when up to 20 pct of the iron was replaced by Fe203.

Jan 1, 1976

By Richard J. Mainiero

The U.S. Bureau of Mines in cooperation with Jim Walter Resources, Inc. (JWR), Brookwood, AL, evaluated the use of sheathed explosive charges in breaking up large stones that can jam the feeder¬breaker or pan conveyor on longwalls and halt operations. Use of the sheathed charge reduced the downtime of the longwall panel to 15 to 30 min as compared with the 1 to 2 h required to drill and shoot the stone. Firing the sheathed charge at the face caused no significant damage to Iongwall equipment. Use of the sheathed charge also represented an improvement in safety by eliminating the exposure of miners to the inherent hazards of the face for extended periods of time. Another benefit, which is difficult to quantify, is the elimination of the temptation to shoot mudcaps or adobes, which is illegal in U.S. underground coal mines.

Jan 1, 1990

By Paul L. Russell

This property has been examined several times in the last few years , and findings have been reported . In the fall of 1942 , the author supervised sampling both lode and placer deposits . The ore was beneficiated , and the results obtained are incorporated in this report . stia The Morgan Group , which comprises seven unpatented mining claims and the Black Cat placer claims , was purchased by the Manganese Products Corp. from H. D. Hill of Hatch , N. Mex . , and Dr. A. C. White of Hot Springs , N. Mex . Arthur L. McRowe , 876 27th Avenue , San Francisco , is president of the corporation , and David Fewer, 824 Times Building, Long Beach, is treasurer . J. T. Murray is in charge of operations .

Feb 1, 1947

By L. J. E. Hofer, J. L. Snyder, J. N. Barn, J. E. Chilton, W. E. Thomas

Various silicone materials have been proposed for use in mining environments. The catalytic methane sensors now employed are poisoned by silicone vapors. Activated charcoal and carbon cloth adsorbents will increase the sensor lifetimes in an environment containing significant silicone vapor concentrations. The results of a study of catalytic methane sensor operation with adsorbent materials in hexamethyldisiloxane-air mixtures are reported. Sampling techniques developed for measuring silicone vapor content of mine atmospheres are described.

To improve the ventilation of large-opening under-ground stone mines by using stoppings made from stone left in place. Background Underground stone mines typically use large room-and-pillar openings with little ventilation control. Stone miners may be exposed to contaminants that include silica dust, diesel particulate matter (DPM), exhaust gases, nuisance dust, and face shot (blasting) fume gases. The health risks from breathing these fine particles and toxic organic materials are well documented. Although contaminants such as dust or diesel exhaust can be some-what controlled at the source, the escaping contaminants are often diluted and removed from work areas using ventilation with minimal controls. In many cases, current mine ventilation practices use trial-and-error techniques to improve ventilation. The growing realization of the importance of a healthy work environment along with increased regulations will require many stone mines to implement new ways to improve ventilation. In-place stone stoppings are one option. Mine air flows from one point to another because of a pressure differential between those points. This pressure differential is established using a mechanical fan in conjunction with separations (stoppings) between high-pressure (intake) and low-pressure (return) airways. The separation of intakes and returns is an important concept that is used in most other types of mines. Normally, air moves through underground stone mines with minimal control technology. Fans are placed in locations where they are thought to be most beneficial, and intakes are not separated from returns. In a few smaller underground stone mines, proper ventilation can be achieved with a few strategically placed fans. However, as these mines increase in size, moving adequate quantities of air through-out the mine becomes harder, and separation of intakes and returns becomes a problem. Building traditional mine stoppings to separate the intake and return airways in entries with a cross-section area often exceeding 800 ft2 is difficult. The stoppings must be able to withstand both the dynamic pressure from face shots and the static pressures created by the fans. Construction and maintenance difficulties, as well as high costs, are the main factors preventing these traditional mine stoppings from gaining wide acceptance by the stone mining industry.

Dec 1, 2002