Search Documents

By J. J. Jakowsky

[The legislation in many States against the present method of producing carbon-black by the incomplete combustion of natural gas, and the continually increasing demand for gas for otter purposes, indicates that the supply of carbon-black may Gradually be decreased and that new methods for its production, utilizing a greater parentage of the carbon in the has should be developed. In the course of investigations of the effects on hydrocarbons of high voltage discharges, it was noted that under certain conditions natural gas could be decomposed and that carbon-black could be produced. The effects of several tyres of electrical discharges on natural gas have, accordingly, been studied' in order to find out the fundamental factors underlying the reactions and their possible influence in the recovery of a greater part of the carbon content of natural gas than is now possible. Present commercial plants using natural gas for the manufacture of carbon-black recover from 0.9 to 1.5 pounds of carbon-black per thousand cubic feet of gala consumed, or less than 5 per cent of the total Gabon in the gas: It should be noted, however, that the, present methods involve heating the gas to incandescense by burning it as a luminous flame, and a considerable part of the gas is thus consumed as a source of hest. If this heat can be supplied from some other source, or if a more efficient method of applying the energy con. tamed in part of the gas, to the decomposition of the rest of it, can be worked out, then a greater yield of carbon-black per thousand cubic feet of gas care be expected. The present abort paper contains a brief summary of tie investigations so far conducted upon natural gas.]

Jan 1, 1922

By H. S. Kalman

A table of factors, for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, is presented. By use of the table the volume of helium in a container, at base conditions of 14.7 psia and 70° F, can be calculated from the observed pressure and temperature of the helium and the known internal volume of the container. The table covers a pressure range from a to 4,500 psia in 10 psi increments and a temperature range of 0° to 120° F in 2° increments. The calculation of volume requires a single multiplication, using a factor from the table and the known internal volume of the container. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1963

By H. S. Kalman

A table of factors, for rapid, accurate calculation of the volume of pure helium in cylindrical steel containers, is presented. By use of the table the volume of helium in a container, at base conditions of 14.7 psia and 70° F, can be calculated from the observed pressure and temperature of the helium and the known internal volume of the container. The table covers a pressure range from 0 to 4,500 psia in 10 psi increments and a temperature range of 0° to 120° F in 2° increments. The calculation of volume requires a single multiplication, using a factor from the table and the known internal volume of the container. A discussion and evaluation of the accuracy obtainable and a derivation of the formula used (which takes into account compressibility of helium, thermal expansion of steel containers, and the stretch of steel due to internal pressure) are presented. An example showing how the table can be used is given also.

Jan 1, 1963

In order to reduce waste and improve resource conservation, mine planning, and development, the U.S. Bureau of Mines is investigating the effects of multiple seam interactions associated with longwall coal mining. Field investigations were conducted at a mine located in Boone County, WV, where a longwall panel was operating subjacent to room-and-pillar workings in an overlying seam. To assess the effects of overlying workings on longwall headgate stability, the Bureau gathered various geotechnical information at this minesite. Headgate pillars and entries were instrumented and monitored to study their behavior during side-abutment loading as the longwall panel approached and passed beneath the overlying room-and-pillar developments. The two operations are separated by 800 ft of interburden, and although interactions between operations separated by this distance are uncommon, geomechanical measurements indicate the occurrence of an interaction. These measurements show that convergence on the headgate entries was most adverse subjacent to barrier pillars in the overlying mine. Pillar measurements indicate that side-abutment pressure increases were slightly greater than predicted values. Several factors related to both geology and mine design, believed responsible for this large interactive distance, are discussed.

Jan 1, 1990

By J. C. Kerkering, S. M. Miller, P. C. McWilliams

Researchers at the U.S. Bureau of Mines investigated the use of close-range photogrammetry and subsequent stereo digitizing to obtain data from rock fracture roughness profiles. The photogrammetric process yielded results that were acceptable but somewhat inferior to those obtained by a mechanical profilometer. On the basis of this study, further pursuit of photogrammetry as a data collection method in mining is proposed. Fractal geometry was investigated as a means of measuring the roughness of rock fracture profiles. Four fractal algorithms were used: divider method, modified divider method, box method, and spectral method. A comparison of the methods gave ambiguous results. Brown's modified divider method provided the best means of obtaining the fractal dimension. Shear strength estimates were obtained using the parameters of the modified divider method and Myers' Z, measure. Because of differences in results when comparing the different ways of obtaining the fractal dimension, future users of fractals in studies of rock fractures are advised to cross-check their results carefully.

Jan 1, 1993

By Frank M. Vodoklys

This is the final report on Contract H0220049 covering the period from 27 April 1972 to 30 April 1974. The objective of the contract was to develop and evaluate materials and methods to achieve post explosion identification of explosives reliably and economically through the use of phosphor coded grains incorporated into the explosive during its manufacture. A coding system of two spotting phosphors and seven coding phosphors was successfully developed during the execution of the contract. The ability of the coded grains to survive detonation in many different types of explosives was demonstrated and the complete code was extracted from a single 100 micron post-explosion fragment. A method was established for testing grain strength to correlate with field test results and an optical system was designed for extracting the code from the grains. Also in fulfillment of the contract requirements a laboratory method for manufacturing the coded grains was established and ten one-pound samples, each with a different code, were fabricated. Finally, a method was developed for applying a coating of polyethylene to the grains to prevent sensitization of the tagged explosives and the ten one-pound samples were coated and delivered to the Bureau of Mines.

Jan 1, 1974

By Paul Hughes

This paper describes a focus of work presently being conducted at the Rock Mechanics Research Group at the University of British Columbia. The underhand method under consolidated fill ensures a high recovery under an engineered back that is comprised of cemented rock fill and/or cemented paste fill. This method of mining has been employed successfully in mines throughout North America as a method of mitigating exposure to the operator having to work under a seismically active ?back?. This paper reviews design methodology in the placement and analysis of sill mats with reference to site observation coupled with on going numerical and analytically derived solutions.

Jan 1, 2006

By Bruce Rock

A continuous mining machine was redesigned for the installation of an integrated illumination system. The illumination system was designed by first calculating the theoretical number of luminaires required to meet the Federal Illumination Standards. Luminaires initially were placed using isointensity diagrams. A darkroom was used for "fine tuning" and demonstrating that the system met the illumination requirements. The luminaire mounts were installed on a machine underground. The performance of this illumination system was monitored in the working environment of an operating coal mine. Design changes were made as necessary during this evaluation period to improve the system.

Jan 1, 1979

By M. C. Malamphy

A general description of the activities and results of bauxite investigation by the Bureau of Mines at its bauxite project in Saline and Pulaski Counties, Ark., has been given in Report of Investigations 4251. In this volume and in a series of Reports of Investigations immediately following the factual data obtained during the project are reported. The data are accompanied by maps showing the location of holes drilled and the deposits developed. Each area upon which work was done is reported by half townships. Each bauxite deposit investigated was assigned a name and a number for ready reference and identification, and its location und name are shown on the appropriate half-township map.-The description of each half township is followed by a description of each deposit developed in that half township. The 14 half-township maps and 77 detail maps of the bauxite deposits in this eeri88 of reports give the locations and numbers of all the holes drilled on the project except the deep holes drilled to test the geophysical anomalies. The locations of those holes show on figure 13 in volume 1 (R. I. 4251). The descriptions of the deposits developed are followed by complete detailed logs of the drill holes. Many of the widely spaced exploratory holes did not discover bauxite of minable thickness and grade. The pertinent information obtained from the widely spaced exploratory drill holes has been summarized and tabulated, and a table tor each half township is given with the discussion covering that area.

Jan 1, 1948

By W. R. Huff

Yield stress and plastic viscosity values, determined from shear rate-shear stress relationships, were found to be a linear function of coal concentration for coal-water slurries containing 40, 45, 50, and 55 weight-percent of powdered coal. In the laminar region, the flow is described by an equation derived from the fact that the square root of the shear stress varied linearily with the square root of the shear rate. In the turbulent region, the friction factor was found to be inversely proportional to the velocity to the 0.12 power.

Jan 1, 1965

By J. A. Herbst

During the last decade it has been established that conventional flotation control strategies based on classical control theory result in significant increases in grade, recovery, and operating-cost savings. In the current report a description of an advanced model-based control philosophy is presented. The derivation and verification of a simplified flotation model is described. The implementation of a Kalman filter for estimation of unmeasured variables for input to controllers is discussed. Several control strategies using the model-based approach are described, emphasizing the nonlinear nature of the flotation plant. Expected trends in the implementation of such model-based flotation control strategies in the future are discussed.

Jan 1, 1986

By L. F. Heising

The Bureau of Mines evaluated 191 composites from the central Mesabi Range, Minn., chiefly by reductive roasting and magnetic separation. After reductive roasting and magnetic separation at minus 325 mesh, 28 composites produced concentrates that contained an average of 66.0 percent iron with less than 10 percent silica. Recovery of contained iron was over 90 percent. Natural magnetic material in excess of 5 percent was present in 142 composites. Trial flotation tests were used to evaluate three samples unresponsive to reductive roasting and magnetic separation procedures, and satisfactory concentrates having low silica contents (averaging 6.6 percent) were achieved.

Jan 1, 1965

By W. M. Nabors

As part of a program to promote conservation and efficient utilization of petroleum resources, Bureau of Mines engineers at the Morgantown (W. Va.) Petroleum Research Laboratory are studying secondary oil-recovery projects in the Appalachian region. The increasing demand for petroleum and its products and the increasing cost of exploratory drilling tend to emphasize the importance of improving the recovery of oil from known petroleum reserves. Published reports setting forth the pertinent facts of these operations may help others to profit by the experience. This report presents the results of a study of secondary-recovery methods used in West Virginia by the Piedmont Oil and Gas Co., the Ryan Oil Co., and Water floods , Inc., on their Roane County leases in the Walton and Clover Rush Run pools. The principal oil-producing horizon underlying the area studied is the Big Injun sand, at approximately 2,000 feet. The sand is often referred to as blanket sand because it underlies much of the State and is oil-productive in many localities. Most of the pools in the area were discovered during 1907 to 1910 and were similarly developed and operated.

Jan 1, 1960

By W. M. Dressel

In producing feed for a lead blast furnace, concentrates analyzing 70 to 80 pct Pb are sintered to produce a physically acceptable low-sulfur product which contains only about 50 pct Pb. Mixtures of PbS with varying amounts of SiO2, CaO, Fe 20., and ZnS were heated in an oxidizing atmosphere at 1,000° C; the products were cooled and examined to determine the problems involved in producing sinter with substantially higher lead levels. Microscopic and electron microprobe studies of the above products as well as experimental and commercial sinters indicate that sinters consist essentially of lead silicates, lead-zinc silicate, calcium zinc silicate, and spinel (ferrite). Lead oxide and lead sulfate areas appear to result from insufficient mixing of the materials prior to sintering. The data give an insight into the process and show that sintering results from a complex interaction of all constituents and that sintering is not simply a matter of diluting the mixture to control the oxidation of lead sulfide.

Jan 1, 1975

By D. J. Bauer

A primary amine extraction system was investigated for fractionating a cerium-group, lanthanide sulfate mixture. Addition of diethylenetriaminepenta-acetic acid (DTPA) to the amine extraction system resulted in separation factors as high as 5.4 for lanthanum-cerium, 8.0 for cerium-praseodymium, 3.7 for praseodymium-neodymium, and 7.0 for neodymium-samarium. In multistage studies on a cerium-free lanthanide mixture, 96 percent of the lanthanum was recovered with a purity of 95 percent.

Jan 1, 1968

By E. R. Cole

Bench-scale research at the Bureau of Mines has resulted in the successful development of a combination electrorefining-electrowinning method for recycling all the lead in scrap batteries. The method reduces energy consumption and eliminates toxic emissions, in contrast to present pyrometallurgical smelting, and the lead produced is pure enough for use in maintenance-free batteries. Anodes cast from molten lead scrap were electrorefined in 1-and 2-liter plastic cells using an electrolyte composition of 70 g/l Pb and 90 g/l free H2SiF6 (fluosilicic acid). Both reagent-grade and waste H2SiF6 were used. Cathode starting sheets were made from refined lead. Aloes, and later bone gelatin, and calcium lignin sulfonate addition agents were employed. The sludge remaining after separation of the lead metal was treated in a two-step leaching operation to solubilize the lead for recovery by electrowinning. Conditions for electrowinning were essentially the same as for electro-refining, except that insoluble Pb02-Ti (lead dioxide-coated titanium) anodes were used. The best results for both electrorefining and electrowinning were obtained with a current density of 170 amp/m2 and a cell temperature of 25° to 35° C. Cathode purity ranged from about 99.9 to 99.99+ pct Pb. Maximum energy consumption after 3 days, for electrorefining and electrowinning, was 90 and 700 kwhr per metric ton of refined lead, respectively.

Jan 1, 1981

By Wm. F. Netzeband

The purpose of this paper is to present to the operators, in other districts a detailed description of the ruining method used and the results obtained to exploiting one of the zinc-lead deposits of the Kansas-Oklahoma-Missouri district. No. 1. mine is located in the heart of the town of Picher in the extreme northeast corner of Oklahoma. HISTORY The first prospect drilling was done at No. 1 mine late in-1914, and shaft sinking was started early in 1915. Sufficient ore was developed to start construction of the mill in April, 1016, Production begin in August, 1916, and the mine s been producing, except for short periods, to the present time. The property was originally a 40-acre tract, but additional properties have been consolidated with the original one until the mine now covers 200 acres.

Jan 1, 1929

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By Israel Liebman

The Bureau of Mines conducted an investigation to determine those factors that are significant in affecting the velocity of flames propagating along the boundary separating gaseous fuel and air. In addition the aerodynamic motion of the gases in the vicinity of such interfacial flames was delineated. Parameters in the study included flammable zone thickness, flammable zone concentration of gradient, fuel type, and position of the flame relative to various environmental surfaces. Of all these factors, the flammable zone thickness and burning velocity of the stoichiometric mixture were found to have the most significant effect on the flame speed. Notion of the gases in the vicinity of the interfacial flames was examined by particle track and interferometric techniques. The relative velocity of the interfacial flame with respect to the unburned gas on the central streamline was found to equal the burning velocity of a stoichiometric homogeneous fuel-air mixture. In addition, it was observed that the composition of the lean fuel-air mixture at the boundary of the combustion zone appears to be less than that defined as the fuel's lower flammable limit.

Jan 1, 1968

Develop a curved ray geotomographic program with constraints to counteract non-uniqueness in order to improve the reliability of seismic tomographic imaging of geological structure in mining regions. Background Seismic tomography provides a two-dimensional image (tomographic reconstruction) of the distribution of the seismic velocity in geologic structures using measured travel times of seismic waves crossing the area. It can provide a more complete representation of features be¬tween boreholes than other crosshole processing methods that measure only average properties or borehole logging methods that measure properties only near each borehole. Seismic tomography has many mining applications. They include locating geologic structures of contrasting seismic velocity, detecting fractured regions where the seismic velocity is low, and monitoring solution injected above the water table where the increase in saturation increases the seismic velocity. Thus, tomographic imaging techniques show great promise for detecting and locating geologic hazards that affect the productivity, safety, and environment of mining operations.

Jan 1, 1992