Search Documents

By G. E. McElroy

[The ventilation of development faces In nines for diluting Gas or dist concentrations and, in hot nines for providing air-motion cooling effect, by fan-pipe units discharging high-velocity steams of air close to the face, is an important phase of mine ventilation. The effectiveness of such units depends largely on the air-flow distribution between the pipe discharge and the face, n subject on which little definite information is available. A study of the air flow from grills into rooms3/ has provided some basic data, but under conditions so different from mine fan-pipe installations in development ends that the data are of doubtful application to mine installations, owing to differences in air-flow conditions.]

Jan 1, 1940

By L. F. Heising

The Bureau of Mines evaluated 191 composites from the central Mesabi Range, Minn., chiefly by reductive roasting and magnetic separation. After reductive roasting and magnetic separation at minus 325 mesh, 28 composites produced concentrates that contained an average of 66.0 percent iron with less than 10 percent silica. Recovery of contained iron was over 90 percent. Natural magnetic material in excess of 5 percent was present in 142 composites. Trial flotation tests were used to evaluate three samples unresponsive to reductive roasting and magnetic separation procedures, and satisfactory concentrates having low silica contents (averaging 6.6 percent) were achieved.

Jan 1, 1965

By William L. Crentz

Early in the nineteenth century, coal from Clearfield County entered the eastern commercial market. Ashley reports that coal was moved down the Susquehanna River by ark from Clearfield to Columbia, a distance of 260 miles, as early as 18o4. Around 1850, the famous Moshannon or Lower Freeport bed was discovered. Several years later the Moshannon Basin was developed extensively, and the coal from this area soon acquired an enviable reputation as a high-quality industrial fuel. Today much of the original Moshannon Basin coal is worked out, and the Lower Kittanning bed has replaced the Lower Freeport bed as the principal source of production in southeast Clearfield County. With depletion of the thick underground deposits, the importance 'of Clearfield County as a coal Producer would have diminished rapidly, if it had not been for strip mining the thinner beds. About 60 percent of the coal produced in the county is strip-mined, and the trend toward this mining method is expected to continue as the older underground operations are exhausted. Many strip mines are working in beds that are too thin to be recovered economically by any other method.

Jan 1, 1952

By W. R. Hardwick

This paper describes block -caving methods and practices of the Bagdad Copper Corp. in Yavapai County , Ariz . It is one of a series being prepared by the Federal Bureau of Mines on mining methods , practices , and costs in various mining districts of the United States . The story of the Bagdad caving operation is of particular interest because the ore body was not as thick as at other mines where the method had been successful . At Bagdad the caving method worked very well as a smallscale operation of 300 tons per day but was abandoned when production was increased to 2,000 tons per day . The Bagdad mine is in western Yavapai County , Ariz . , about 22 miles northwest of Hillside , a station on the Phoenix -Ash Fork branch of the Atchison , Topeka & Santa Fe Railway system ( fig . 1 ) . Copper ore now is mined by open -pit methods . The ore is concentrated , and the concentrates are trucked to Hillside and shipped by rail to a custom smelter . Some molybdenum sulfide is produced as a byproduct . This report gives a brief history of the district , describes the ore de- posit , and outlines the methods of prospecting , exploration , and estimation of ore . Development and former underground mining , including stope preparation , stoping , and transportation , are described . Extraction of ore , production rates , miscellaneous operations related to mining , wage and contract systems , and method of concentration are described . The final section discusses mining costs . The underground mine was visited by the author several times between 1937 and 1942 , and some information has been drawn from personal notes . The property again was visited in June 1957 , and maps and plans for this paper were furnished by the company at that time ; they have been edited to conform with Bureau of Mines format . The underground mine could not be visited then because it had been closed in 1948 when open -pit mining was begun .

Jan 1, 1959

By Alan R. Buehler

In 1986, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied part of the 256,430-acre Alvord Desert and part of the 22,240-acre East Alvord Wilderness Study Area (OR-002-074 and OR-002-073A, respectively), in order to evaluate their identified mineral resources. The study areas are located in Harney and Malheur Counties, OR, about 25 mi northeast of the small village of Fields. There are no mines, prospects, or identified mineral resources inside the study areas. Basalt flows within the study areas contain chalcedony-lined vugs and banded agate which may be of interest to rock hounds. An ignimbrite flow contains perlitic material, but crystalline contaminants make it unsuitable for commercial uses. Lacustrine (lake) sediments contain diatomite and clays, and evaporite crusts contain boron too low grade to profitably mine. Small quantities of common opal and petrified wood occur which might be of possible interest to rock hounds. Some of the petrified wood is black, free of fractures, and polishes well; it may be suitable as backing material for soft, thin, and brittle gemstones, such as precious opal. The lacustrine sediments also contain black, fetid layers which have above background, but economically insignificant concentrations of zinc, cobalt, nickel, barium, iron, manganese, aluminum, and potassium. Large quantities of fine-grained dune sands within the study areas are too far from markets for economic consideration. Ephemeral streams in the study areas contain small amounts of placer gold of no economic interest. The western portions of both study areas are reported to have moderate favorability for occurrences of natural gas, and both study areas are reported to have high favorability for the occurrence of geothermal resources. As of December 1986, oil and gas leases covered 3,100 acres in the study areas.

Jan 1, 1987

By F. J. Palumbo

An electronic color-sorting machine was tested for recovering colorless glass concentrates from mixed glass products. The tests were made using glass recovered from unincinerated (raw) urban refuse and residues resulting from the incineration of refuse. The results of the study revealed that concentrates analyzing about 86 percent colorless glass could be recovered from mixed unincinerated glass containing 54 percent colorless glass material. Recovery of the colorless glass was about 62 percent. Color sorting the incinerated glass was somewhat more difficult. Multiple-stage processing was required to recover 59 percent of the colorless glass material in a product analyzing 89 percent colorless glass. The feed material analyzed 41 percent colorless glass.

Jan 1, 1971

By Victor R. Spironello

Applications of three experimental design techniques to smelting operations are explained. The report describes a factorial design using three variables at two levels, a fractional factorial design which investigates seven variables, and response-surface methodology for optimization of electric- furnace smelting processes. These methods may be applied with a minimum of trials and at little expense. Further, the writer knows of no reasons why the same methods could not be applied to other operations as well, such as steelmaking.

Jan 1, 1970

[This is the eighth in a series of reports on properties of commercial motor fuels, made in accordance with a cooperative agreement between the Cooperative Fuel Research (C.F.R.) Committee and the Bureau of Mines of the United States Department of the interior. The fir t report gave data on motor gasolines sold during the winter of 1935-36.3/ The present report, covering 1,679 simples, represents the products of US companies plus those from the Pacific coast, witch were averaged by the Pacific Coast Technical Group before being submitted and arc published exactly as they were submitted. The three groups of data on samples of regular, premium, and third-grade gasolines are averred separately. the, number of samples and brands representing each grade are as follows: Regular price, 869 samples, 76 brands; premium price, 452 sample, 45 brands; third-grade 358 samples, 52 brands. In this report the same marketing districts are retained as were used in the preceding report, and as for as possible the actual sampling points in each area are indicated on table 1.]

Jan 1, 1940

By Thomas E. Green

A combined solvent extract ion-spectrophotometric method for the determination of as little as 1 ppm of copper in tungsten metal or tungstic oxide has been developed and evaluated. Metallic samples are converted to tungstic oxide by treatment with hydrofluoric and nitric acids. The oxide is then dissolved in sodium hydroxide, and the copper is extracted as the colored neocuproine complex. Total elapsed time for the analysis is approximately 1-1/2 days; however, actual working time for a group of six or eight determinations is less than 4 hours. Precision at the 2-ppm level is better than 0.1 ppm.

Jan 1, 1963

By W. J. Long

The gradual depletion of high-grade mineral deposits and the necessity for development of lower-grade deposits together with the increased demand for nonmetallic minerals has increased the importance of the ore-dressing field during recent years. There is strong need for development of new ore-concentration methods and-machines to keep pace with the constant changing of marketing specifications and requirements resulting owing to the many new uses made of mineral products by the metallurgical industry.

Jan 1, 1948

By R. L. Grant, R. W. Van Dolah, N. E. Hanna

An experimental investigation was conducted to assay the relation between natural gas concentration and ignitibility of the gallery atmosphere . Both the gas concentration representing maximum ignitibility and the relationship between certain properties of the explosives and their incendivity are discussed . The data show that variation in the natural gas content in the gallery can have a highly significant effect on ignitibility of the gallery atmosphere ; maximum ignitibility of the atmosphere by permissible explosives occurs with approximately 8.1 percent natural gas . The study also shows that incendivity of a permissible explosive cannot be determined only by its detonation velocity , oxygen balance , or ballistic mortar strength . However , for similar type explosives , trends observed indicate that their incendivity increases with detonation velocity or bulk strength . Additionally , for underoxidized explosives studied here , the more negative the oxygen balance the less incendive was the explosive within a class defined by salt content .

Jan 1, 1963

By E. G. King

This report contains experimentally determined heat-content values for cerium dioxide and Columbium (niobium) dioxide in the temperature range from 298° to 1,800° K. There are no previous similar data for Columbium dioxide, and those for cerium dioxide have an upper limit of 373° K. The heat-content and corresponding entropy-increment data are presented in tabular form. Equations were derived to represent the heat contents and heat capacities. The data for cerium dioxide are entirely regular, but those for columbium dioxide show two previously unreported anomalies at 1,090° and 1,200° K.

Jan 1, 1961

By Oliver Bowles

"Underground operation.In its broader sense the term ""mining"" is applied to all processes whereby raw materials are taken from the earth to be used as sources of mineral products. In a more restricted sense ""mining"" is applied to underground operations as contrasted with open pit work designated as quarrying. The tern is used in the restricted tense in this paper; for it relates to the exploitation of limestone deposits by modern methods of underground operation rather than by open pit methods.Present tendency toward miningIt may seem to some readers that a paper on mining limestone will find little general interest among lime plant operators, for only a limited number of them have yet resorted to this means of procuring raw materials. It is noteworthy, however, that a growing tendency exists toward underground operation, for one by one quarry owners are faced with increasing difficulties in open pit operation. It seems desirable, therefore, for operators to keep closely in touch with this gradual change in process, to inquire into the underlying causes, to compare costs, and to study the effects of the change in method on subsequent steps in calcining the stone to produce lime."

Mar 1, 1924

By T. L. Joseph

"IntroductionThe efficiency of ore reduction in the blast furnace and fuel requirements depend upon the degree of uniformity with which reducing gases can be distributed through the stock column and upon the permeability of individual pieces of ore and sinter. If the ore is fine, the major problem in reduction is to get the ascending gas stream to the surface of the ore-Hard, dense ores of low permeability, mined in coarse sizes, tend to improve the permeability of the bed, but unless they are crushed to the proper size they reach the hearth unreduced.Surveys by the Bureau of Mines have shown conclusively that the gas distribution in the upper three fourths of the furnace is far from ideal. Furnace lines, top design, and methods of charging are important, but more thorough size preparation of the ore is necessary to eliminate size segregation at the stock line, which inevitably leads to non-uniformities in gas distribution.Because of the quantity of sinter now produced close study of the characteristics which determine its behavior in smelting is warranted. As the use of concentrates increases agglomeration will become more of a necessity. Improvements in the physical character of the ore burden are particularly important to plants using coke of poor physical quality. In addition to aiding reduction, improved physical properties of the ore burden will permit the use of higher blast heats, which is equally important.Reduction Tests on Fine Sizes of SinterPrevious reduction tests on minus 0.742— plus 0.525--inch pieces of commercial sinters revealed large differences in porosity and reducibility. The results have been published in a former report. 3 Although the physical properties of the sinter, particularly porosity, were found to be of major importance in determining the rate of deoxidization, it appeared that certain chemical properties of the sinter appreciably retarded the reduction of sinters high in silica. This was attributed to the presence of fayalite, which has been identified by Schwartz and by Luyken and Kraeber4 as an important constituent of sinter. Although furnace operators and metallurgists have assumed that iron silicate is more difficult to reduce than hematite or magnetite, definite data on the reduction characteristics of this material were not available. Tests were undertaken, therefore, to develop a method for de-termining the amount of iron silicate present in sinters so that its effect upon reduction could be observed."

Jun 1, 1934

By D. Harrington

Fine ventilation was discussed. much more 15 to 20 years ago than it is now, yet today there are tendencies in connection with ,-line ventilation (in fact, numerous ventilation systems have been installed in recent years) indicating that the lessons learned by bitter experience in the past either have been forgotten or lave not been brought to the attention of the present generation. Possibly, the mining min of today considers that conditions have changed so much that experiences of the past cannot be repeated today. At any rate, it seems desirable to restate some of the principles of mine ventilation that were understood more or less in the past and to call attention to some danger in connection with present-day trends or practices.

Jan 1, 1939

By Naoki Hosoya, Setsuo Maeda

This paper addresses establishment of an experimental system for measuring biodynamic response (BR) of hand-arm system at the NIIH in Japan. BR measurement system at the NIIH is nearly equivalent to NIOSH installed system. The feasibility of the system is examined through the apparent mass (AM) measurement of the empty handle and a set of calibration masses. Apparatus The grip force was measured by using the handle shown in Fig. 1. The handle has two force sensors (KISTLER, 9212) and one accelerometer (PCB, 356A12). A low-pass filter with 5 Hz cut-off frequency was used to the grip force from measured force signal. Figure 2 shows BR measurement system in this study. The push or pull force at the handle was measured by using the force plate (KISTLER, 9286AA). The grip force and the push / pull force were displayed on a monitor. The shaker (IMV, VE-100S) is used to vibrate the hand-arm system along the forearm axis (Zh direction) (ISO 10068, 1998; ISO 5349-1, 2001). In most situations force actions for operating tools are expressed by grip, push, pull and combined these actions. These actions can be simulated in the test system. AM was obtained by performing H1 estimator in the PULSETM system (B&K, 3109) and it is denoted at the one-third octave band center frequencies. [ ] Methods In order to investigate the reliability of the system, AM measurement of the handle was performed. It is assumed that the handle is rigid in the upper limit of adoptive frequency range in this study. This assumption is validated in AM measurement of the empty handle. A pseudo-random vibration in the frequency range of 10 to 1,250 Hz was used and its amplitude is 1.0 (m/s2)2/Hz with a flat power spectral density (PSD) in the experiment. Measured AM includes the mass effect of the measuring cap in a subject experiment. Compensated apparent mass AMc(?) is obtained by Eq. (1) 1-2.

Jan 6, 2006

By E. P. Youngman

At the time of the preparation of the monograph upon the mining legisla- tion of Newfoundland, by the Imperial Institute of London, the existing local statutory law (as distinct from case laws and the applicable English acts) con- sisted of the following legislation: 1. Chapter 129 of the consolidated statutes, entitled "Of Crown Lands, Timber, Mines and Minerals," as amended by the Crown lands act, 1928. 2. Chapters 131 and 132 of the consolidated statutes (acts relating to mines regulation and rewards for discovery of minerals, respectively). 3. Crown lands act, 1918, as amended by the crown lands (amendment) act, 1921. 4. The Labrador Act, 1927. 5. The Crown royalties act, 1927. 6. Crown lands act, 1928, together with rules and regulations issued thereunder.

Oct 1, 1932

This publication summarizes the in-house and contract research and development projects programed for fiscal year 1981 by the Bureau of Mines under its Minerals Environmental Technology activity. The document provides a mechanism for interested parties, including potential contractors, to gain insight into ongoing and projected work of the Bureau?s environmental research efforts. Research to identify and correct environmental problems associated with mining and metallurgical operations has long been an integral part of the Bureau's mission. The environmental research and demonstration activities of the Bureau were consolidate in 1979 with the formation of the Minerals Environmental Technology program, which is directed toward the elimination or reduction of environmental problems associated with the extraction and processing of minerals. Among the efforts underway are development of data and technology for assessing the potential environmental impact of minerals development, for monitoring minerals extraction operations, and for establishing viable reclamation requirements on abandoned mine lands; development and demonstration of technology 'or control of environmental disturbances during minerals extraction operations; development and demonstration of land reclamation and mine closure techniques to restore or enhance the productive use of mined lands; development of engineering techniques that incorporate state-of-the-art mining environmental technology in the design and planning of minerals extraction operations; development and demonstration of new mining systems that greatly reduce or eliminate the adverse environmental impacts of minerals extraction; and providing the technologic base for Federal, State, and local establishment of environmental standards for mining operations. Included in the minerals-processing-related work are projects to clean mineral-processing waters: demonstrate a Bureau process for scrubbing SO from powerplant stack :;as; recover dissolved minerals from process streams; stabilize discarded dusts, slags, and tailings: remove hazardous contaminates from byproduct wastes; reduce generation of waste solids; and improve metallurgical process engineering to eliminate pollution. Approximately $21 million was appropriated for this work in fiscal year 1981.

Jan 1, 1981

By E. J. Gleim

The importance of "good voltage," especially for direct-current systems in coal mines, is not always fully appreciated. From the practical aspect there are three viewpoints from which low voltage may be considered, namely: (a) its effect upon operation of electrical equipment, (b) its effect upon cost of maintenance and power, and (c) its effect upon safety in the mine. The design of electrical motor-driven equipment usually is based upon a given or assumed constant value for the voltage of the system; consequently, when there is an appreciable drop below this value, unsatisfactory operation is likely to follow. In the case of shaker conveyors, for example, one manufacturer has pointed out that these conveyors must be operated at a certain definite speed if maximum output is to be secured. As shunt motors are used in the conveyor drives, either a rise or fall in voltage will produce corresponding changes in speed and thus seriously affect the efficiency of the conveyor. The introduction of automatic control for mine equipment has been greatly retarded because the relays, contactors, and other special devices required have failed to function properly when attempt was made to operate them on systems subject to variable and low-voltage conditions.

Jan 1, 1937

By Lijun Xu, Jan M. Mutmansky

"Mutmansky, J.M. and· Lijun Xu, 1989. Some observations on particulates collected in underground coal mines using diesel and non-diesel equipment. Min. Sci. Technol., 9: 207-218.The results obtained when sampling twenty underground coal mine sections, each in a different mine, are outlined. The sampling effort was oriented toward a detailed characterization of coal mine dusts and thus eight-stage Anderson Model 298 impactors were used as the primary collection instrument. This instrument allowed a fairly detailed size distribution for each of the particulates sampled. Because four of the mines used diesel outby equipment and/or diesel shuttle cars at the face, it is possible to make some comparisons of the particulate distributions in diesel versus non-diesel mines.One of the more interesting results is the pattern that exists in mines lising diesels only for outby utility haulage. Particulates in these mines seem to be consistently heavy in the fine size ranges, perhaps being of significant concern to the industry. While no definite conclusions can be drawn from the limited data, a more detailed study of particulates may provide a better picture of particulate loadings.IntroductionThe subject of particulate emiss1ons from underground diesel equipment is currently a very important topic as health concerns and regulation of diesel particulate emissions have created new environmental problems for mine operators. The amount of particulate matter originating from diesels has not been extensively measured and problems of differentiating coal and mineral dust from diesel particulates make existing data questionable.However, it is necessary to make an assessment of the problem in order to solve it. It is known that particulates from diesel engines are solid aerosols formed in the combustion process. Technically, this places the particles in the category of fumes. It is also known from tests where no mineral dust could be a factor in the measurements that about 90% of diesel particles are less than 1 µm in aerodynamic diameter [3]. To measure the diesel component of a coal/diesel particulate to measure, Johnson et al. [2] have developed procedures for utilizing laser Raman spectroscopy. The determination of diesel content in a coal/diesel mixture is difficult due to the chemical similarity of the two organic materials. However, laser Raman spectroscopy, which is often used for identification of organic materials, has potential if the Raman spectra for the two materials are different and unique. The study concluded that an accuracy of ±~% could be achieved for mixtures containing up to 55% diesel particulate. The method is relatively complex and would need further development for routine application."

Jan 1, 1990