Search Documents

By Nunna Malakondaiah

Plant samples collected from the mined sites of Beulah, Center and Zap and the test sites of North Beulah 1, North Beulah If, South Beulahh and Center were analyzed for their nutrient concentrations. The vegetation from the mined areas generally showed lower concentrations of Na, P and Cu and failed to meet the nutritional requirements for beef cattle as defined by National Research Council (minimum requirements are: Na, 600; Cu, 4; P, 1800 µg/g dry weight). Plants from Beulah showed generally higher concentrations than from Center or Tap. Tissue concentrations of K varied significantly between sites for 5 species due to the low tissue concentrations at Center. Deficiencies are difficult to isolate as the sampling was done in mid-summer and generally during that season the tissue concentrations tend to decrease in several species. All of the plant species at the unmined sites, with the exception of western wheatgrass at Zap, had lower concentrations of P than the minimum nutritional requirements for beef cattle. Sodium concentration was low but Cu was marginal to adequate in plant species at the unmined sites. Concentrations of K, Mn and Cu in western wheatgrass were greater at Center than at Zap while the opposite was true of the concentrations of Zn, Cu and P in blue grama and Cu in green needlegrass. Amending the spoil with slack at North Beulah I decreased the concentrations of Zn, Cu and P in wheatgrasses grown on spoil from 0-2, 5-10, and 20-25 foot depths, respectively. In general, the mean tissue K+/Na+ ratios were greater in plants on slack amended spoils, primarily due to the reduced Na concentrations in the tissue. At North Beulah II test site, only wheatgrasses grown on spoil amended with slack showed significant increase in K and decrease in Na and Mn concentrations. At South Beulah test site which received 12" topsoil over graded spoil, leonardite amendment decreased P concentrations in all of the grasses as compared to control, whereas fertilizer treatment increased the same. Nutrient concentrations were lower in both fescue and needlegrass with leonardite treatment and higher with fertilizer treatment although not significantly different from control. The concentrations of Ca, Mg, Na, Fe, Cu and N in grasses grown on topsoil at Center test site were significantly higher than on slack amended spoil. Legumes grown on topsoil at Center site contained higher concentrations of P than those grown on spoil; there were no significant effects due to slack on spoil or topsoil. The data presented in this report act only as an indication of between-treatment and between-species differences in tissue composition of plants harvested in mid-summer season. With respect to the nutrients analyzed, since none were found to be toxic, the cattle can safely feed on the vegetation of these mined areas.

Jan 1, 1982

By Virgil J. Stachura

The Bureau of Mines has investigated techniques and instrumentation that measure accurately the airblast overpressures from surface mine blasting. The results include equivalencies between broadband research instrumentation and commercially available impulse precision sound levels meters measuring: root-mean-square, peak, fast, slow, impulse, A and C weighting, C-weighted sound exposure level (CSEL), and "linear" (flat) response. These values were obtained from field measurements and broadband FM tape recordings of production blasts at area and contour coal mines, limestones quarries, and iron mines. Frequency response was determined for 14 commercial systems.

Jan 1, 1981

Publicize the valuable information resources covering research conducted by the U.S. Bureau of Mines (USBM) and other federal laboratories that may be of interest to USBM customers. Access to this information is important for promoting further research and in transferring the technology to the end user. USBM Information Resources The USBM serves as the Nation's premier agency for mining- and minerals-related research. In sharing the benefits of this research with American industry and the American people, the USBM supports information systems outlining this vast array of technical knowledge. The USBM is dedicated to making its technology readily available and will continue to expand its electronic communications capabilities. The following resources provide instant access to USBM information. U.S. Bureau of Mines Bulletin Board. The Bulletin Board is a free service accessed by computer modem. All that you need are a computer, a modem, and communications software. The telephone number for the Bulletin Board is 202-501-0373; for information on using the system call 202-501-0406. Use X-modem protocol set to 1200, 2400, or 9600 baud, 8 data bits, and 1 stop bit (8,N,1). The information on the system can be viewed or downloaded. This service includes the following: announcements on Bulletin Board and other USBM activities; mineral news, features, and press releases from the Bureau's Office of Public Information; a list of recent publications and articles by USBM authors; mineral commodity data and Mineral Industry Survey reports; USBM Technology News, concise factsheets announcing milestones in USBM research and technology; a current list of computer products available from the USBM and the National Technical Information Service (NTIS); and a listing of cooperative research opportunities with the USBM.

Jan 1, 1995

By Edward L. McHugh, Louis J. Denes, Jami M. Girard

A prototype portable hyperspectral imager that operates in the visible and near-infrared ranges of the electromagnetic spectrum was field tested at an open-pit mine. The tests were sponsored by the Spokane Research Laboratory, National Institute for Occupational Safety and Health, as part of an investigation of remote sensing technologies for use in detecting and monitoring conditions in surface mines that could lead to catastrophic slope failure. The spectro-polarimetric imager, built at the Carnegie Mellon Research Institute, employs an acousto-optical tunable filter (AOTF) to control wavelength, a phase retarder to measure polarization signatures, and a digital camera and computer to capture data. The spectral range of the instrument is 450 to 1000 nm at 10-nm intervals. High-resolution hyperspectral images of highwalls, outcrops, hand samples, and drill core were collected in the field. Spectra from the images closely matched those of specific minerals present and were used to classify the images. The field tests were designed to examine the feasibility of using spectral imaging to assist in compiling objective geologic maps of mine highwalls and other hazardous slopes. Results illustrate the capability of the method to discriminate materials within the image, validating the concept of simplified spectral imaging. A contributing factor in many slope failures is the presence and distribution of mechanically incompetent, clay-rich altered rock in slope faces. Spectral features of clays and other minerals are more distinctive in the short-wave and mid-infrared part of the spectrum; the capabilities of the instrument need to be extended into this range to apply the AOTF-based technology to common geologic materials. A field-portable hyperspectral imager could find broad application in remotely identifying diverse materials from solids and coatings to gases.

By H. J. Heinen

The Bureau of Mines, investigated a cyanidation-carbon adsorption technique for extracting gold from arsenopyrite concentrates. Agitation leach experiments were conducted on 85-pct-minus-35-mesh gravity concentrates containing 21.8 oz gold and 6.4 oz silver per ton. Results obtained in leaching the concentrates showed that 96.9 pct gold and 90.7 pct silver extraction could be achieved in 96 hours of agitation. Gold and silver were recovered from the resulting pregnant solution by exposure to granular activated carbon in a countercurrent system. Carbon loadings of 2,556 oz of gold and 502 oz of silver per ton were achieved. These loadings are significantly higher than heretofore thought practical.

Jan 1, 1980

By T. W. Beck

The National Institute for Occupational Safety and Health (NIOSH) conducratory and field tests to evaluate the effectiveness of dust collector bags for reducing dust liberation and operator exposure from a roof bolter’s dust collection system. The laboratory tests evaluated the bag’s effectiveness to contain dust and the effect on canister filter loading in both a bag and bagless condition. The dust emissions from the collector’s exhaust were also measured in each condition during laboratory testing and show that nearly 100% of the test dust fed into the collector was captured by the dust bags. Loading and pressure drop on the dust collector’s canister filter is greatly decreased when using the bags, enabling longer periods of drilling without filter removal/cleaning. The field results showed that, even though dust standards were met, respirable dust in exhausted emissions was reduced around the bolter. Laboratory and field results show that benefits from use of the bags are realized in all areas of operator exposure.

By M. J. Ackerman

This study was undertaken to make a comparison between the cost of mining coal under roof bolt and under conventional timber methods of roof support. Studies were made at 14 mines in Pennsylvania, eastern Ohio, and northern and southern West Virginia. At each mine data were obtained for sections of the mine where the physical conditions, mining equipment, and mining systems were similar. Coal, recognized as one of the basic industrial fuels, is very competitive with other fuels, and management, in order to protect and enlarge its market, must be continually alert to find more efficient methods of production. Continuous production of coal is desired by all operators but never obtained. In mechanized mining the performance and production vary with operating time, which can be interrupted by many variable factors, such as condition of the roof, method of roof support, condition of equipment, water, ventilation, power, transportation, efficiency of operating crew, and supervision.

Jan 1, 1961

By K. R. Dorman

To further investigate the potential of precast concrete sets as a support medium for underground mines, the Bureau of Mines designed a five-piece precast concrete drift set for a small opening and tested it to destruction in a straining frame. Twenty-seven tests were made with three sizes of members using three loading conditions. In addition, six tests were made with sets in a distorted configuration, Test results and typical failure patterns are presented. A comparison of results with those previously reported for the three-piece set shows the five-piece set supports considerably larger total loads than does the three-piece set of equivalent cross section designed for the same size of opening. Recommendations are made for improvements in design.

Jan 1, 1969

By H. R. Pierce

Bureau of Mines engineers end others have endeavored to deter-nine a fundamental method for gauging the capacity of gas wells to deliver gas under different pressure conditions. Their studies show that for accurate gauging two factors must be determined: (1) The actual pressures at the face of the sand in the well (usually referred to as "at the sand"), acid (2) the relation between such pressures and the rates. of flow of c as through the sand. This paper, the first of a series, describes a method of attacking the problem of determining the actual pressures at the sand by means of observations of pressures and volumes at the well head.

Jan 1, 1929

By W. T. Wertman

A research program to aid development of better and more efficient methods for producing petroleum and increasing its ultimate recovery from underground formations is an integral part of the work of the Bureau of Mines on conservation of the Nation's natural resources. Economic, efficient production of recoverable oil and gas from a reservoir depends to a great extent upon the best and most accurate information that can be obtained from a study of the reservoir rock and its fluid contents. Information on oil and water saturation is pertinent and essential in wildcat, extension, and pool wells for good reservoir operations and prediction of performance. This report presents results of an investigation by the Bureau of Mines of core recovery and degree of drilling-fluid contamination occurring during cable-tool coring operations using oil-base mud. Representative core samples were obtained from 6 major oil-producing sands in 8 fields of West Virginia, Pennsylvania, and New York. Field-mixed, oil-base drilling mud was used for the first coring test, and lightweight, premixed oil-base mud, with an organic chloride tracer added, was used in coring eight other wells. Tracer analyses were made to determine contamination of core by drilling-fluid filtrate. Core analyses, including oil and water content and minimum interstitial water-saturation tests, were made on selected core samples to compare and evaluate water saturations determined by the two methods.

Jan 1, 1958

By G. N. Schrauzer

Work has been carried out in the development and testing of carbon monoxide (CO) detection devices which use silica-gel impregnated with metal salts. If carbon monoxide is present, the ?detection gel? (the treated silica-gel) changes from a yellow to a blue-green or blue color. The detection gel "regenerates", i.e., returns to its original yellow color, within 4-24 hours after removal from air containing CO. The detection gel exhibits a threshold of CO response which can be adjusted over a wide range of CO concentrations, typically from 50-500 ppm in air. The preparation of detection gel using salts of palladium, molybdenum and copper is described. Also reported are the results of testing the detection gel&apos;s response to carbon monoxide under varying conditions of temperature and humidity and in the presence of some potentially interfering gases. Low levels of hydrogen sulfide (~ 5 ppm)1 nitrogen dioxide (< 7 ppm), and acetylene (> 200 ppm) were found to affect the detection gel. Temperature and humidity were also found to affect the detection gel&apos;s response. Increasing temperature shortens the gel?s response time while increasing the humidity delays the gel?s response and alters the threshold of the gel. A brief discussion of the further research and development necessary to stabilize the detection gel?s desirable characteristics is included. Descriptions of testing equipment and procedures are covered in detail.

Jan 1, 1978

By William A. Beck

"The Piedmont Manganese Belt extends from Taliferro County, Georgia, 70 miles in a northeasterly direction through Greenwood County, South Carolina, and conforms with the trend of the Piedmont Province. The total area of the belt is reported to be about 1,000 square miles, and the maximum-width is about 24 miles.Manganese has been known to exist in the belt since 1845. M. Tuomey mentioned a deposit in the Edgefield district on Hard Labor Creek in South Carolina in a report on the geology of South Carolina published in 1848.Ore was first mined about the time of the first World War, when the Colley mine, near Lincolnton, Ga., was. Opened. The only operation in the area at present is that of the Abernathy & Kehaya Mining Co., at McCormick, S. C.The geographical position of the belt is from west longitude 82° 57’, north latitude 33° 39' to west longitude 82° 06', north latitude 34° 08'. The towns of Washington and Lincolnton, Ga., and McCormick and Greenwood, S. C., are in or near the belt.An exploratory project of the Bureau of Mines was started on the McCormick, S. C., deposit in April 1944, and trenching, test pitting, and hand-auger drilling-were done on a small scale until early in October 1944. (Fig. 1.) In November 1944 work was begun on a property 12 miles north of McCormick, known as Parsons Mountain, which is leased to M. H. McKnight by the United States Forest Service. From March 15 to March 24, 1945, work was done on the property of Mrs. H. B. Ross, which is known as the Morgan farm.The Abernathy & Kehaya manganese mine contains what is locally known as the Dorn gold mine; mineral rights on the property were owned by M. G. & J. J. Dorn, Inc."

Apr 1, 1946

By R. L. King

This report describes a method for designing and constructing ground beds that has been developed under the sponsorship of the Bureau of Mines. The procedures for designing and constructing a driven-rod ground bed with a resistance of 5 ohms or less are given. Some of the theory of soil resistivity and fall-of-potential resistance measurements is included. Results of a bed constructed at the Bureau of Mines mine car roadway are presented.

Jan 1, 1978

By Thomas E. Doerfler

Information and data related to the occurrence of fatalities due to major disasters in metal/nonmetal underground mines were analyzed. Standard statistical methods were used to estimate the probability of occurrence of major disasters, and to examine the relationship of disasters to injury statistics published annually.

Jan 1, 1980

Reduce accidents associated with handling of the electrical trailing cable and the water hose on mining equipment. Approach Two reels were mounted on a loading machine to store and release the lines as required during face operations. How It Works A hydraulic motor, which is actuated by a treadle valve in the operator&apos;s cab, controls the reel on which 50 feet of electrical power cable is stored. A spring motor resists unwinding of the other reel on which 50 feet of water hose is stored. Both reels are mounted on the right rear of the loading machine. See Figure 1. Following common mining practice, the cable and hose are anchored to fixed points at the first intersection outby the face. Tramming forward causes the cable and hose to be pulled from the reels. Depressing the treadle valve causes the electric cable reel to turn and wind-in any slack in the cable. The spring tension on the water hose reel automatically rewinds the water hose when the loader is trammed in reverse.

Jan 1, 1978

By J. R. Thoenen

In Progress Rerort 1,4/ a number of facto were demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

By J. H. East, R. S. Sanford, W. M. Traver, W. S. Wright

"INTRODUCTION This report describes the results obtained from a diamond-drill exploration project performed by the Bureau of Mines on the nickel deposits of the Yakobi Island, Alaska. The Federal Geological Survey 6/ completed a detailed geologic study and mapped the area during the summer of 1940, and a Bureau of Mines examining engineer 7/ made a preliminary examination of the deposits in June 1941, at which time core drilling was suggested as the logical means of determining the extent and grade of the deposits. Equipment and supplies were unloaded on the beach at Yakobi Island on October 21, 1941. The drills were moved to Bohemia Basin, where actual drilling operations wore begun under the direction of a Bureau of Mines engineer 8/ on November 7, 1941. Two core-drill holes were completed on December 7, 1941. Upon the request of the drilling contractor, operations were recessed owing to severe winter conditions. Work on the project was resumed April 27, 1942, under the direction of another Bureau of Mines engineer 9/ and was completed August 15, 1942. During the 1942 season, 13 core-drill holes were completed, and 10 surface pits and a tunnel were sampled. A total of 5, 191 feet of core-drill hole was drilled in 15 holes during the entire project. The results of drilling and sampling form the basis of this report."

Jan 1, 1948

By Albert L. Toenges

EARLY in 1949, the Economic Cooperation Administration requested the Bureau of Mines to assign a coal-mining engineer to study milling conditions in Greek lignite mines; to make recommendations for the introduction of methods and practices that should increase production and decrease the cost of mining; and, from the results of a geological reconnaissance by geologists of the United States Geological Survey, to suggest plans for the development of mines to supply fuel for a thermal power plant, Albert L. Toenges was assigned to this investigation and arrived in Athens, Greece, March 15, 1949. The study of mining operations and the geological reconnaissance (which was made by W. G. Pierce and X. M. Denson, geologists, United States Geological Survey) Were conducted concurrently. The Geological Survey will publish the results of its investigation separately. Washability studies of lignites from Aliveri and Kimi were made at the Central Experiment Station of the Bureau of -Mines, Pittsburgh, Pa. The lignite fields mentioned in this bulletin are shown in figure 1.

Jan 1, 1951

By Russell R. Trengove

The Strawberry tungsten mine is in the Jackass Mining District, in an isolated portion of eastern Madera County, near the southeast corner of the Yosemite National Park. The deposit was discovered in 1941, and production started in 1943 when the mill was completed. With the exception of 1946 and 1947, production has been continuous. The area in the vicinity of the mine is granite containing islands of sedimentary beds highly altered by metamorphism that resulted from the intrusion of acid igneous rock. Schoelite occurs in almost vertical lenses of tactite between the limestone and the granite.

Jan 1, 1949

By L. B. Berger

Tests and observations of a Diesel-powered locomotive used for under-ground haulage, in a-clay mine were made by representatives-of the Bureau of Mines .primarily to determine the composition of the exhaust gases produced by the engine under actual haulage conditions-and to determine the effects of the operation on the quality of the mine atmosphere. In addition to ascertaining these conditional t proved interesting to analyze the test, data in regard to certain other performance, characteristics of the engine. This report presents results of tests of the mine locomotive, prefaced by a brief resume of the performance characteristics of Diesel engines to facilitate discussion.

Jan 1, 1948