Search Documents

By Harold P. Rue

The problem of removing hydrogen sulphide from natural gas has become within the last few years one of major importance to the natural gas and petroleum industry. Several gas fields in the United States produce natural gas containing hydrogen sulphide, and a number of oil fields produce gas which contains hydrogen sulphide. 3 The percentage of hydrogen sulphide in natural gas produced in these fields varies from a fraction of 1 per cent t6 as high as 20.5 per cent by volume. 4 Hydrogen sulphide is probably the most toxic gas associated with natural gas,5 and from the standpoint of health and safety it is important that the hydrogen sulphide be removed if the gas is to be used for domestic purposes. Hydrogen sulphide, besides being toxic and therefore a hazard to animal life, is under certain conditions an active corrosive agent and very destructive to equipment. 6 The annual loss caused by the corrosive action of hydrogen sulphide on equipment amounts to hundreds of thousands, perhaps millions, of dollars. 7 The largest percentage of natural gas produced in the United States comes from wells which also produce oil. This associated gas invariably carries with it light fractions of petroleum, which when separated from the gas, condense to the liquid form at ordinary temperatures and pressure. Commercial application is made of this natural condition, and "wet gas" is processed to obtain so-called natural gasoline by employing the principles of absorption, adsorption, or compression and subsequent expansion accompanied by cooling. In the manufacture of natural gasoline from wet gas which contains hydrogen sulphide, if this contaminating gas is not first removed, some of the hydrogen sulphide may oxidize to form free

Jan 1, 1932

The contract objective was to evaluate sources of airborne quartz and research control methods that would assist underground mine operators in complying with respirable dust standards which have been reduced because of quartz in the dust exceeding five percent. The work involved: Phase I -evaluate sources of quartz dust at the roof bolter work location; Phase II -evaluate the relationship between the quartz content of the coal and adjoining rock strata and quartz exposure at the roof bolter and continuous miner locations Phase III -conduct laboratory tests to determine performance parameters for roof bolter dust collector systems. The underground surveys for Phases I and II determined: (1) the continuous miner typically is the greatest source of quartz exposure for the miner and roof bolter operators when single-split ventilation is utilized, (2) a statistically significant relationship be­tween quartz content in face material and operator exposure was not determined and data suggested mining equipment and procedures may be more critical. The Phase III lab tests indicated the use of dust hog-type bits, filter cartridges, maximized collector airflow, and reduced bit rpm should be utilized to minimize dust liberation at the roof bolter.

Jan 1, 1985

By Irving Hartmann

The Bureau of Minas has been charged by the Congress with the responsibility for administrating the provisions of the Federal Coal-Mine Safety Act. One of the important duties of bureau inspectors under this act is to determine whether proper measures are taken to prevent mine explosions, which in moat miner includes Judea adequate rock dusting The investigation made after the explosion in Orient No. 2 mine, December 21, 1951, showed that much information is lacking on the adequacy of current rock-dusting and duet-sampling practices in the United States. To obtain such information, an intensive sampling survey was conducted by the Bureau in an Indiana coal mine. This paper summarizes the more Important findings from this survey, describes special samplings at several Pennsylvania coal miners, and discusses related studies in the Bureau's Experimental coal mine.

Jan 1, 1954

By Karl R. Becker

A variety of commercial detonators (fuse type and electric instantaneous and delay types) were subjected to impact and thermal stimuli to determine initiation stimulus levels and the dominant parameters in resistance to initiation. In the impact trials the detonators were impacted along their length to find the most sensitive region; threshold initiation limits obtained for these regions ranged from 3.47 to 20.82 joules (2.6 to 15.4 ft-lb). The friction sensitivity of the explosive component was an important parameter in determining sensitivity; various construction features of nonexplosive components played a role as well. In the thermal sensitivity trials, the detonators were heated from ambient to 100° C at an average rate of about 1.0° C/min, and thereafter at 0.5° C/min until they exploded; the explosion temperatures observed ranged from 121° to 188° C. These temperatures correlated quite well with the reaction temperatures of certain characteristic explosive components used by different manufacturers. The data also indicated an effect of confinement on explosion temperatures of detonators.

Jan 1, 1975

By J. H. Field

Results of studies by the Federal Bureau of Mines on a pilot-plant scale for removing hydrogen sulfide and carbonyl sulfide from gas mixtures by the hot carbonate system are given in this publication. Gases containing up to 10 pet. hydrogen sulfide and 48 grains carbonyl sulfide per 100 cu.ft. were treated. In most tests carbon dioxide also was present and was removed simultaneously with the sulfur compounds. Because the rate of absorption of hydrogen sulfide is much more rapid than that of carbon dioxide over a wide temperature range, selective removal of hydrogen sulfide occurred in the bottom section of the absorber near the point of gas entry. Hydrogen sulfide was removed to pipeline specifications with carbonate solutions by using split-stream flows in the absorber and regenerator.

Jan 1, 1960

By Alan G. Mayton

A prototype end-cab shuttle car (SC) design has been developed to improve protection and address ergonomic concerns of the SC operator in low coal mines. The new design features an end cab transversely mounted to the SC and equipped with a closed-circuit video system. The end cab was retrofitted to a low-coal SC and evaluated in surface trials at the U.S. Bureau of Mines. During surface trials, test operators evaluated the end-cab SC relative to visibility; cab features-space, seating, controls, and operator position; tramming-inby, outby, and turning corners; and dumping. Trials were conducted using 12 test subjects; 6 were experienced SC operators. Results of the trials were promising. Of the experienced operators, the only operator with low-coal experience gave the new design the highest rating. Four experienced operators rated the end-cab design "better" to "much better" than a standard center-driven, side-cab SC for visibility when tramming, protection from roof and rib hazards, and no change in seat position with direction of travel. This report discusses research to modify a used 21SC JOY SC, retrofit the SC with the Bureau-developed end-cab, and evaluate the retrofitted end-cab SC in surface trials.

Jan 1, 1993

By John J. Sammarco

This U.S. Bureau of Mines report describes the research effort and results for a computer-assisted appendage control system of a Joy 14CM continuous mining machine. The cutter head (shear), gathering head, conveyor, and stabilizer jack are the appendages. Positional control of each appendage is accomplished by specifying the desired position to the appendage control computer, which uses appendage position sensor data. Appendage movement is actuated until the desired position is attained as determined by control algorithms. A description of the sensors, mechanical and electrical interfaces, data acquisition and control (DAC) system, experimental method to determine appendage response characteristics (range of motion, start and stop delay times, and movement rates), and their application to the position control loop algorithms are presented. Also, the test results for the shear in an unloaded (free space) and loaded (cutting) condition of the shear are presented.

Jan 1, 1991

By F. E. Joyce

This paper describes the development of a process for producing manganese and iron pellet concentrates from low-grade manganiferous iron ores of the Cuyuna range by a two-stage sulfatization-reduction roast. First, the manganese minerals (7.5 percent manganese) were converted to water-soluble manganese sulfate by roasting in sulfur oxide gases at 700° C, then, the hematitic iron minerals (31 percent iron) in the hot sulfatized are were reduced to magnetite with simulated reformed natural gas in the temperature range of 350° to 425° C. Batch tests were made in a 3-inch-ID by 6-inch-long, gas-heated, stainless steel retort, and continuous countercurrent experiments were performed in a 2-inch-ID by 10-foot-long, electrically heated shaft furnace. Manganese sulfate was removed from the roasted product by leaching with water, and over 90 percent of the manganese was recovered in an oxide product (65 percent manganese) obtained by precipitation, drying, and thelmal decomposition of the sulfate. An iron oxide concentrate (60 percent iron) with an iron recovery of 75 percent was obtained from the water-insoluble residue by magnetic separation.

Jan 1, 1973

By James A. Whelan

The Bureau of Mines sponsored research studies of variables in rotary drilling, done in the Department of Mineral Engineering, University of Minnesota. By studying carefully controlled drilling with good instrumentation, it was hoped to obtain a better understanding of rock failure during drilling and of the stresses in drill bits during drilling. Experimental procedures and equipment are described. From these studies it was concluded that 1. Thrust requirements, other things being equal, are proportional to the total length of cutting edge in the bit. 2. Data from penetrating a wedge into rock under thrust only are not directly applicable to rotary drilling. 3, In rotary drilling the initial wear on a bit greatly decreases penetration rate under any given set of conditions; however, after initial wear the effect of wear on penetration rate is reduced. 4. An increase in rotary speed increases the overall penetration rate but decreases the penetration per revolution. 5. An increase in thrust increases the overall penetration rate and the penetration per revolution. 6, Torque on a drill bit is proportional to both penetration rate and bit diameter. 7. For small-diameter holes full-hole drilling will save both drilling time and energy compared with pilot drilling followed by reaming; for large-diameter holes pilot drilling-reaming is advantageous in both respects,

Jan 1, 1962

This report is the 23d in a series summarizing research and technologic work by the Federal Bureau of Mines on coal and related investigations; it is the fifth report to be issued on a calendar-year basis.2/ Publications by Bureau personnel in 1958 are cited;3/ in addition work in progress during the year is briefly described. To conserve our reserves of coal the Bureau of Mines conducts a program concerned with the development of fundamental information on coal characteristics and behavior, and the improvement of technology related to its production and utilization. The ability to anticipate and meet future demands for coal depends on a number of factors: (1) Knowledge of reserves from a stand- point of both quantity and quality; (2) the development of improved mining methods, health and safety measures, and preparation techniques that will insure its most efficient exploitation; and (3) knowledge of the controlling factors in efficient use of coal in combustion, carbonization, gasification, direct and indirect hydrogenation, and other new processes. The Bureau is concerned with each of these areas.4/,5/

Jan 1, 1960

By Joseph M. Pugliese

This work was done by the Bureau of Mines to provide quarry operators with an uncomplicated, first-approximation method for designing blast patterns, considering geologic structure, and to show the valid use of the technique by comparing drill and blast pattern dimensions used in the quarry with those determined by the presented method. The author visited 12 limestone and dolomite quarries in Ohio (Adam, Crawford, and Highland Counties), Wisconsin (Milwaukee, Racine, and Waukesha Counties), and Minnesota (Fillmore, Olmsted, and Wabasha Counties); observed the blasting practices; studied the major geologic features; and after discussion with the quarry managers, foremen, and blasters, compared the quarry blasting patterns with those as calculated by the empirical formulas (after R. L. Ash), with geologic structural considerations. When geologic structure such as bedding, jointing, folding, and caves, as well as explosive properties and field performance characteristics are accounted for in a manner suggested by the research, the presented empirical formulas may be used as a good first approximation. The included steps in planning a blast design and generalized blast patterns should be of help to the quarry operator. Design changes are recommended for those quarries where problems are occurring.

Jan 1, 1972

By Jean M. Kenney

Frequencies of haulage-related accidents in metal and nonmetal surface mines for the years 1988 through 1990 were investigated and compared with those of non-haulage-related accidents. This study was part of the U.S. Bureau of Mines program to improve mining haulage safety. Data were obtained through the U.S. Bureau of Mines Accident Data Analysis (ADA) program. The chi-square test was used to compare frequencies of haulage-related and non-haulage-related accidents for each of the following variables: degree of injury, age, total number of years of mining experience, and shift time. Significance was determined for degree of injury between haulage-related and non-haulage-related accidents. Age of injured did not vary significantly between haulage-related and non-haulage-related accidents, but total number of years of mining experience was found to be significant. Shift time for the accident proved to vary significantly between haulage-and non-haulage-related accidents. Events causing injury for haulage-related accidents were tabulated, and the most frequent determinants of haulage-related accidents were identified. Accident descriptions for both fatalities and permanent disabilities were studied, and the primary causes of these accidents were identified. These findings suggest that haulage-related jobs are among the most dangerous when considering accidents experienced by all workers in the metal and nonmetal surface mining work force.

Jan 1, 1993

By Donald O. Capstick

In 1981, U.S. Bureau of Mines personnel conducted a survey of claims and prospects in the Wheeler Ridge RARE II area to determine if mineral resources or potential for resources exists at deposits in the area. Results of Bureau of Mines investigations indicate the area contains no identified mineral deposits. However, the geologic setting at the Round Valley Peak Prospect near the center of the study area is considered to be favorable for the discovery of tungsten resources with associated molybdenum and copper. Tungsten deposits, should they be present, would be expected to occur at depth in tactite at or near the calcareous rock-granite intrusive contact. Sand, gravel, and stone deposits in the area are not considered to be resources because equal or better quality material is available closer to major markets. INTRODUCTION The 16,200-acre (6,560 ha) Wheeler Ridge study area is 11 mi (18 km) northwest of Bishop, California, on the eastern flank of the Sierra Nevada range. The John Muir Wilderness adjoins the study area's western boundary (fig. 1).

Jan 1, 1983

By Richard L. Jenkins

Systematic sampling, in reconnaissance fashion, of the continental shelves of the United States to define favorable areas of offshore mineral deposits, is one of the long-range marine mineral; programs of the U.S. Department of the Interior. In mid-1966 the Department of the Interior launched its Heavy Metals Program to stimulate domestic output of gold which is in serious short supply. The program is jointly conducted by the Geological Survey and the Bureau of Mines.

Jan 1, 1968

By C. W. Smith

Research was conducted to evaluate the effectiveness of a well-point dewatering system in conjunction with a french drain to intercept waste impoundment leakage while reducing the volume of waste water requiring treatment. A well-point dewatering system composed of 585 production wells was installed around the perimeter of a leaking impoundment that previously used only a french-drain system for leakage control. The placement of the well-point system was designed to intercept and remove the leakage from the groundwater before the contaminant reached the french drain. Groundwater monitoring at this site revealed that after a period of approximately 40 days the well-point dewatering system had stabilized and effectively prevented the further spread of contamination to the french drain.

Jan 1, 2010

By J. R. Thoenen

In Progress Report 1,4/ a number of facto mere demonstrated and conclusions drawn from experimental tests and records made during commercial blasting operations at a number of quarries. For example, the tests showed (1) that vibrations received on outcrops were of comparatively

Jan 1, 1938

This Bureau of Mines publication contains the texts of the four papers presented at the May 6-7, 1980, seminar on the role of overburden analysis in surface mining. Coverage includes the geologic distribution of pyrite and calcareous material and its relationship to overburden sampling, overburden sampling and analysis, use of soil-overburden data in mine planning and development, and minesoil classification.

Jan 1, 1981

Objective: To continuously monitor, display, and record concentration levels of respirable coal mine dust in mines to an accuracy of ±25% with a 95% confidence level for at least 30 days without servicing.

Jul 1, 1997

By P. T. Brooks

Mineral nodules from the ocean floor represent a vast potential source of manganese, nickel, cobalt, and copper. Process development studies to devise methods for recovering these metals were conducted by the Bureau of Mines using two types of nodules--relatively low-grade calcareous nodules from the Atlantic Ocean and higher grade siliceous nodules from the Pacific Ocean. Ammoniacal carbonate leaching of reduced nodules appeared to have the best potential for processing the calcareous nodules, but the method proved to be impractical for recovering manganese. Extraction of 90 percent or better of the nickel, cobalt, and copper showed the technique to be attractive for recovery of these metals. The siliceous nodules appeared amenable to a process that starts with either a sulfur dioxide leach or a sulfation roast followed by a water leach to dissolve the soluble sulfates.

Jan 1, 1971

By A. R. Taylor

Using solution calorimetry, the following heats of reaction were determined: (1) NaCN(c) + 1/Cu20(c) + 129H20(l) ? CuCN(c) + NaOH?128.5H2O ?H = -13.44±0.10 kcal/mole, (2) HCN(2) + NaOH?128.5H20 ? NaCN(c) + 129.5H20(l) ? = -2.52±0.02 kcal/mole. From these reactions, the heats of formation for CuCN(c) and HCN(2) were calculated to be 22.7±0.4 kcal/mole and 24.9±0.4 kcal/mole, respectively. Reaction 2 was made to check the consistency of literature values for heats of formation of HCN and NaCN. Adiabatic calorimetric measurements between 10° and 400° K showed the entropy and heat capacity of CuCN(c) to be 21.51±0.06 eu and 14.58±0.04 cal/mole deg, respectively, at 298° K. A broad anomaly in the heat capacity was found in the temperature range 285°-320° K. The heat of transition associated with this anomaly was less than 1 cal/mole, the sensitivity of the measurements.

Jan 1, 1971