Search Documents

By R. V. Ramani, J. Qin

"In this paper, the results of a research study on airborne dust transport in a full scale simulated longwall face are presented. The simulated longwall face was set up in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines to conduct experiments under controlled conditions. The controlled parameters in the experiments were the dust dispersion rate, dust size distribution, density of the dust, air velocity, and the rate of travel of the dust generating source. The analyses of the experimental results on mass concentrations, particle size distributions, and real-time respirable dust concentrations are discussed. There are definite spatio-temporal trends between the location of the shearer, the concentration at any location in the face, and the dust generation rates. The size-consist and density characteristics of the source dust, the air velocity in the face, and the air leakage into the gobs all affect the concentration. INTRODUCTIONA detailed experimental study on the characteristics of longwall dust cloud in operating longwall faces has been reported by Ramani, Qin, and Jankowski (1991). The study indicated that there are several important factors whose effects on dust transport in longwall faces need to be further investigated. In an operating longwall face, the effect of these parameters could not be easily isolated as control over the affecting parameters is not readily possible. In a simulated longwall face, however, these parameters can be controlled. Therefore, as a follow-up to the field study, a series of controlled experiments were conducted in a full scale simulated longwall face in the Lake Lynn Laboratory mine of the U.S. Bureau of Mines [Qin, 1992]. Specific aspects which were addressed during the experimental design phase included determining the types of samples to be collected, selecting proper instruments to collect these samples, and developing detailed sampling and time-study plans to correlate the dust concentrations with face activities. Two types of dust--anthracite and bituminous--were used. Dust dispersion rate into the air as well as the source dust particle size distribution were documented. Control was exercised over both air velocity at the face and air leakage along the longwall face. During experiments, the dust source was moved to simulate the shearer movement at operating longwall faces. Detailed descriptions of the design of experiments, experimental results, and data analyses follow in the subsequent sections."

Dec 1, 1996

By Harry W. Campbell

A Bureau of Mines investigation identified no mineral deposits in the Lost Creek RARE II area. Sand and gravel has been mined from alluvial flood plain deposits just outside the RARE II boundary. An oil and gas lease application which includes the eastern portion of the RARE II area is pending. Abundant basalt in the area can be crushed and used as aggregate; but it could not compete with similar deposits in more favorable locations, or with cheaper substitutes such as volcanic cinders or sand and gravel which are available outside the study area closer to major markets. No indication of coal or geothermal energy resources was found. INTRODUCTION Location and Access The Lost Creek RARE II area encompasses 8,300 acres (3,400 ha) of Lassen National Forest in north-central California, about 20 mi (30 km) north of Lassen Peak. The closest city is Redding, California, 50 air mi (80 km) southwest. Peripheral access is provided by State Highway 89 passing near the western RARE II boundary (fig. 1). The Pacific Crest Trail traverses the western margin of Hat Creek Rim adjacent to the eastern boundary of the area.

Jan 1, 1983

By L. J. Kane

Conventional methods for determining the size of dust suspended in a gas require that agglomerates (clusters of particles) first be broken into particles, but in evaluating industrial dust-removing equipment the size of the agglomerates as they actually exist in the gas stream is far more important. This paper presents results of an investigation by the Federal Bureau of Mines to develop methods for determining the size of dust agglomerates suspended in a gas stream. The studies are part of the Bureau's continuing research on synthetic liquid fuels. The size and size-distribution of agglomerates as they exist when the gas reaches the filter was determined by using a membrane filter in conjunction with a dust count under a microscope. A membrane filter is a cellulosic sheet about 150 microns thick containing millions of holes per square centimeter--holes of uniform diameter that run directly through the sheet without interconnection.

Jan 1, 1960

By G. R. Hopkins

[Apparent progress in fuel economy at petroleum refineries, as measured by the average amount of .seat units required to refine a barrel of crude oil, received a set-back in 1935, when the average rose to 562,00 B. t. u., compared with 562,000 B.t.u. in 1937 (see fig. l). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 wan the decline in total runs to Invariably the average requirement increases when crude ins to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries arc masked by the degree to which the capacity is utilized. Additional crude runs give lower average e heat requirements in two ways - first, because they are mane with the c expenditure of comparatively small amounts of auxiliary heat, and, second, because the additional runs generally represent simple topping operations. In 1938 crude runs, to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938 .]

Jan 1, 1939

By G. L. Oldwright, Virgil Miller

"The data presented in this paper were collected at the smelter of the Consolidated Mining & Smelting Co. of Canada Limited, Trail (Tadanac), Brithish Columbia. The authors are greatly indicated to S.G. Blayrock, vice president and general manager; James Buchman, smelter superintendent; and the staff members mentioned in Report of Investigation 3243. The authors are exceedingly grateful to George Murray, assistant smelter superintendent, for his keen interest, suggestions, and help in carrying out this investigation.INTRODUCTIONThe methods of charign the blast furnaces at Toole and Kelloggs were noted in Report of Investigations 2957 and 3094 respectively. Report of Investigations 2957 cited (4 to 9 inclusive) Hofman's Metallurgy of Lead (p. 226) and the work of A.S. Dwight, Thompson and Sicka, the staff of the Engineering and Mining Journal, and L.D. Anderson, N.F. Collins, in The Metallurgy of Lead (Chas. Griffin, London, 1910) also gives (pp. 247 254) the principles that he believes govern the successful charging of the blast furnace."

Dec 1, 1934

By G. R. Hopkins

[Apparent progress in economy at petroleum refineries, as measured by the average amount of hest units required to refine a barrel or crude oil, received a set-back in 1938, when the average rose to 567,000 B. t. u., compared with 562,000 B. t. u. in 1937 (see fig. 1). The primary factor in the rise in average heat requirement's per barrel of crude oil refined in 1938 was the decline in total runs to Invariably the average requirement increases when crude inn to stills decline, and vice versa. In other words, annual gains in fuel efficiency at refineries are masked by the degree to which the capacity is utilized. Additional crude runs give lower average heat requirements in two grays first, because they are mane with the expenditure of cc-comparatively small amounts s of auxiliary heat, and, second, because additional runs generally represent simple topping operations. In 1938 crude runs to stills declined 1.6 percent (from 1,183,440,000 barrels in 1937 to 1,165,015,000 barrels in 1938), but the total heat consumption declined only 0.4 percent, or from. 663,866 billion B. t. u. in 1777 to 660, 56 billion in 1938.]

Jan 1, 1939

By Edward A. Barrett, Kathleen M. Kowalski-Trakofler

This paper discusses the application of a training intervention that uses degraded images for improving the hazard recognition skills of miners. Method: NIOSH researchers, in an extensive literature review, identified fundamental psychological principles on perception that may be employed to enhance the ability of miners to recognize and respond to hazards in their dangerous work environment. Three studies were conducted to evaluate the effectiveness of the degraded image training intervention. A model of hazard recognition was developed to guide the study. Results: In the first study, miners from Pennsylvania, West Virginia and Alabama, who were taught with the aid of degraded images, scored significantly better on follow—up hazard recognition performance measures than those trained using traditional instructional methodologies. The second and third studies investigated the effectiveness of the training intervention at two mining companies. Data collected over a3—year period showed that lost—time injuries at mines in Alabama and Illinois declined soon after the training intervention was instituted. Impact on Industry: Further exploration of the hazard recognition model and the development of other interventions based on the model could support the validity of the steps in the hazard recognition model.

By A. Wahab Khair, W. M. Devilder

"This paper presents an analysis of fragment size distribution and characteristics of fracture surface in coal cutting using a rotary coal cutting simulator. Coal cutting by a drum type continuous miner was simulated in the laboratory. A series of tests along both the face and butt cleat direction of coal under different operating and in-situ conditions were performed. In each experiment the cut surface was photographed microscopically and the coal cuttings were collected and sized. Data were used to show how and to what extent various parameters effect size distribution of the coal cutting and how this correlates with the characteristics of the fracture surface. This study resulted in establishing a number of distinct correlations between the size distribution and fracture surface. These correlations were primarily based on the degree of interaction between adjacent bits and the amount of bit-coal interaction taking place on the cutting path. Some of the major results of this study are as follows:Zones of bit-coal interactions proved vital toward understanding the effect the conical bit has on the fragmentation process. This in turn led to the identification of areas which are responsible for the production of fines and generation of respirable dust.The various parameters employed in the coal cutting experiments which showed a strong effect on the coal fragment size distribution were: bit type, bit spacing, depth of cut, in-situ stresses, and cleat orientation. Bit angle and cutting head velocity exhibited the least effect and no correlation was established.From this study it is obvious that the key to achieving efficient coal fragmentation is to limit the degree of bit-coal interaction that takes place throughout the bit path while causing maximum interaction between adjacent bits. Accomplishing this not only increases the percentage of large fragments produced but limits the amount of secondary crushing that takes place in the bit path thus resulting in decreasing fines and consequently, the amount of respirable dust generated.Over 2,000 continuous mining machines (introduced in the 1950's) equipped with conical bits or point attach bits account for well over half of the United States' production from underground coal mines. Today, competition in the coal industry has increased, due mainly to coal market conditions and legal restrictions, thus placing an emphasis upon increasing production, efficiency and health/safety of the workers. Mine operators are always interested in finding the most efficient performance of continuous mining machinery to produce the largest amount of size of coal at the lowest cost. An increase of fine material sent to the cleaning plant can seriously overload the plant to the extent that plant efficiencies deteriorate significantly (1). Also, the difficulty and expense of cleaning very small particles often cannot be done economically and thus, thousands of tons of coal are sent to the refuse pile because of costly or ineffective cleaning facilities. It has been said, ""the efficient extraction of coal or rock implies breakage into a size range that contains a minimum quantity of very small sizes"" (2). All known fragmentation theories concur that more fragmentation requires more energy (3). So, the importance of reducing fines is already evident from an outlook upon efficiency.Now, let's consider another view point., duet generation."

Jun 1, 1988

By Thomas E. Marshall, Michael Dunn, L. J. Prosser, Anthony T. Iannacchione

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) examined and characterized conditions at a majority of the underground stone mines in the United States. Observations at these mines revealed a limited degree of roof monitoring beyond visual inspection and sounding. When monitors are used, they typically require the miner to measure movement at the roof. If conditions are unstable, the mine rmay be in a hazardous situation while recording data. Based on this scenario, researchers surmised that a simple, inexpensive monitor with the capability of recording data at a distance from the mine roof would be a safer way to gain the information. Additionally, more widespread use of monitors could potentially lead to better understanding of roof movement in general. A monitor to meet this need was designed, tested, and subsequently improved as experience was gained in its’ use at a number of underground stone mines. The Roof Monitoring Safety System (RMSS) can provide an initial indication of movement in roof beams. By understanding and measuring roof movement in underground mines, the potential for injuries and fatalities to mine workers from falls of ground can be reduced. Also, officials at a mine with a history of data are better prepared to make a decision on remedial actions in the event of ground falls. This paper will outline the evolution of the RMSS and how it can be used in a comprehensive proactive ground control safety program. Also included is a case history describing how the RMSS was used in an evaluation of the effectiveness of a mechanical impact scaling machine at an operating limestone mine.

By Z. J. Fink

Ultraviolet-visible and infrared emission spectra from propagating methane-coal-dust-inhibitor mixtures have been obtained in a 0.2-by 0.2¬by 5.3-m vertical duct over a range of flame speeds from 2 to 100 m/sec. Results serve as a basis for the design and evaluation of thermal radiation detectors for triggered barriers that suppress ongoing mine explosions. Of particular significance is the large continua superimposed on the methane-air spectra when small amounts of coal dust are present and the variation of emissivity with infrared (IR) wavelength in dust flames. In conjunction with the spectral measurements, studies of flame speed, particle size, gas sampling plus thermodynamics, and dust sampling are presented and discussed in order to gain insight into the more fundamental aspects of propagating explosions. Sampling results have shown that only a near-stoichiometric amount of dust is consumed in the flames studied even though initial concentrations are five times stoichiometric. Difficulty in propagating coal-dust inhibitor flames of realistic mine characteristics in a cold-walled laboratory duct has been encountered. A simplified analysis of the flame zone utilizing spectral and sampling results indicates that the stability of slowly propagating flames is more dependent upon thermal radiation than upon convection losses to the walls. It is predicted that thermal radiation losses will make any measurements of coal dust burning velocities, "quenching diameters," or flammability limits more apparatus dependent than those corresponding to gaseous fuels.

Jan 1, 1974

By F. N. Kissell, C. M. McCulloch, Maurice Deul, J. R. Levine

The methane content of virgin bituminous coalbed can now be measured accurately in the field with exploration core samples from vertical boreholes. The gas content of the coal per unit weight can be used either to design a mine ventilation system or to determine if degasification of the coalbed will be necessary before mining, and to determine the gas resources in the coalbed. The equipment necessary to conduct the test costs less than $50. The gas content of the coal in place in the ground is determined by summing the gas lost from coring, gas measured during desorption, and the residual gas in the coal. Upon removal from the borehole, the core sample is placed in an airtight container and desorbed for several weeks until the desorption rate is below 0.05 cm3/g for 5 consecutive days. The gas lost from the core while it was being cored and the residual gas are estimated by a new graphical method. The amount of gas remaining depends upon whether the coal is friable or blocky. Friability appears to relate to the depth of the sample below the surface, fixed carbon percentage, Hardgrove grindability index, and proximity to tectonic disturbance. Friable coals emit nearly 96 pct of the total gas during desorption whereas a blocky coal emits only 60 pct of its total gas. Coalbeds that are ill defined as to their blocky or friable nature must be tested in the laboratory for unambiguous analysis.

Jan 1, 1975

By D. L. Boreck

Thick coal seams are common in the Western United States, Many seams are over 50 it thick (some are over 200 ft thick) and are too deep to extract using surface methods. Currently, such deposits are developed using standard "eastern" mining methods which only extract a few feet of total seam thickness, often rendering the remaining coal unminable with current technology. Novel methods that increase thick-seam recovery have been developed and are currently being used in Europe. These methods--high-face single-pass and multislice longwall, longwall caving, and hydraulic mining--have great potential for use in the United States. Successful use of these methods is an objective of the Bureau of Mines. Their use requires, among other things, a full evaluation of geologic features common to thick coals. The objective of this report is to present and summarize those features that will affect the introduction of the methods into thick-seam mines in the Western United States. The geologic elements delineated are three-dimensional configuration of the seam, cleat development, joints and fractures, roof and floor lithology, and faulting.

Jan 1, 1986

By T. T. Campbell

This investigation was undertaken by the Bureau of Mines to determine if high-purity ductile molybdenum of uniform quality can be prepared by bomb reduction techniques. Molybdenum trioxide (Mo03) and mixtures of molybdenum dioxide (Mo02) and trioxide were reduced by magnesium in closed steel bomb reactors. Very high pressures in excess of 5,000 p.s.i. developed during magnesium reductions of Mo03. The addition of calcium oxide to the bomb charges caused a significant reduction in pressure. Reaction efficiencies higher than 95 percent were obtained during magnesium reductions of either Mo03 or mixtures of Mo02 and Mo03, but high pressures were encountered when the charges contained from 30 to 60 percent Mo02. Reaction efficiencies were usually low (less than 80 percent) when the bomb charges contained more than 40 percent Mo02. The charges with the best composition considering operating pressure, yield, and purity contained from 10 to 30 percent Mo02. The addition of small amounts of carbon to the reaction charges was helpful because some deoxidation occurred during the reduction and also during subsequent arc-melting of the regulus metal. The purity of the bomb-reduced, arc-cast molybdenum metal ranged from 99.2 to 99.8 percent and in some instances the metal contained as little as 5 parts per million oxygen.

Jan 1, 1962

By Gregory Molinda

Historically, coal miners have known that roof shales can deteriorate in contact with humid mine air, causing massive roof falls and injuries from falling rock. It is critical to recognize rocks prone to weathering and to adequately support these rocks in order to ensure the long-term stability of the openings. In a recent study, NIOSH has used a wet/dry cycling test to determine the moisture sensitivity of over 800 specimens of roof rock from 25 U.S. coal mines. Fireclays and some gray shales are the most moisture-sensitive. Rocks with disturbed bedding, in contrast to flat-bedded rocks, are also more sensitive to water. Black shales are relatively un-reactive to moisture and serve to protect more reactive gray shales above. Mines that have roof rocks with moisture-sensitivity indexes above 40% can experience slaking roof conditions, and many require high coverage surface controls. Three case studies are presented in which the moisture-sensitivity index is correlated to roof conditions underground, and can be used to indicate long term deterioration. Engineering measures are described to control moisture-sensitive roof. In one case, roof screen not only reduces injuries from rock fall but also is shown to reduce roof falls. Keywords: coal mining, roof control, slaking, roof support, rock falls

Jan 1, 2008

By M. J. Kovalik

The effects of the process variables on the production of chemical coke on a chain grate stoker, a type of traveling grate, were studied. Six bituminous coals, ranging in volatile matter from 16.7 to 43.8 percent, were successfully carbonized, yielding chemical coke with acceptable physical properties. The coke yields were dependent on the volatile-matter content of the coal. The air fuel ratio had the most marked effect on the yield and characteristics of the resultant coke, and the general furnace performance. Results can only be predicted; the actual yield and quality of coke obtained from any given coal can only be determined by actual tests using the optimum processing variables to obtain a coke with minimum volatile-matter content and to retain as much of the fixed carbon in the original coal as possible.

Jan 1, 1967

By S. P. Howell

The Bureau of lines as repeatedly called attention to dangerous practices in the transportation and opening of kogs of black blasting powder. In 1914 Diwin Higgins (Prevention of Accidents from Explosives in Metal inos, Miners' Circular 19, Bureau of Mines, p. 15) stated "canisters should always be opened by removing the bung. To use a pick or other sharp tool for cutting a hole in the canister is dangerous. After the necessary amount of powder has boon taken out, the canister should be kept closed. The powdor should always be handled at a safe distance from an open light." In 1919, Geo. S. Rice (onthly Statement of Coal line Fatalities for June, 1919, Bureau of Mines, pp. 16 to 18) calls attention to the dangers that arise in underground transportation and handling of explosives, and calls special attmtion to the danger of hauling explosives in motor trips; the unnecessary risk involved in hauling men on the trip at the same time, and the necessity of keeping open lights away from black blasting powder. In 1919 the writer (Sensitiveness of Explosives to Frictional Impact, Tech. Paper 234, Bureau of Mines, pp. 13, 15) called attention to the fact that black blasting powder is not as sensitive to frictional impact as the nitro-glycerin dynamites and the gelatin dynamites. Black powder may be ignited by direct impact and the writer believes that this may occur without presupposing a preliminary spark. It is well known, however, that black blasting powder is very sensitive to ignition by spark flame, or heated materials, and these may be produced by an electric current, by an open light, by incandescent particles from a pipe, cigar, or cigarette, by the tearing of metal sheets or scraping of metal against metal, and possibly, by other means. -- The above discussion will serve to introduce a newly recognized hazard the ignition of black blasting powder by the forcible opening of kegs with wodden tools. The details of three accidents in which kegs of black blasting powder ex- ploded instantly when a wooden tool was driven forcibly through the top of the kegs are as follows: 1. In 1915, a powder man employed by a coal mining company stated that he was opening a 25-pound log of black blasting powder by driving a hole in the top with a wooden sprag when the powder in the leg ho was opening ignitod. This caused the ignition of fifty-two additional 25-pound logs of the powder, and the fatal burning of this and another powder man. The ono making this statement lived five hours after the explosion.

Sep 1, 1920

By H. P. Hermance

The Ore Hill zinc-lead mine in Grafton County, N. H., was investigated by the Bureau of Mines from March to July 1943 and from August to October 1944. Fourteen holes with an aggregate bore of 4,899 feet were diamond-drilled, the old workings were unwatered and sampled to an inclined depth of 250 feet, and the tailings dumps were surveyed and sampled. The deposit at the Ore Hill mine comprises a bedding-plane vein of massive sphalerite and galena with subordinate chalcopyrite and pyrite in a series of interbedded metasedimentary and metavolcanic schists about one-quarter mile east of their contact with the intrusive Baker Pond gneiss. The property was first opened about 1850 and was active at times to 1914. Production records are not available, but the output is believed to have been considerable. In 1944, leasers recovered a marketable mica product from mica schist from the dumps and certain outcrops. This report describes the work performed in the Bureau's investigation and presents the data obtained.

Jan 1, 1948

By J. E. Miller

This paper reports experimental determinations by the Bureau of Mines of compressibility factors to 4,000 pounds per square inch absolute (p.s.i.a.) for helium at temperatures from -10° to 130° F. and for 16 helium-nitrogen mixtures at 70° F. This information is needed for computing accurate discharge volumes and is necessary for determining an average-density value for use in orifice-meter formulas. In thermodynamic calculations, several functions of the compressibility factor with pressure and temperature are required. The data in the original publications (6, 8)5 of this study have been reexamined and have been given a more comprehensive treatment. The recalculated compressibility factors are higher by approximately 0.2 percent because in the earlier work a linear relationship between the compressibility factor of helium and pressure was assumed.

Jan 1, 1961

The general nature of the special constructional features that are required to provide safety from explosion hazards on machines approved as permissible by the Bureau of Mines is fairly well known to mining men who are at all interested in safety. These requirements are outlined in the schedules under the provisions of which the investigations of such machines are conducted. Also, the method of conducting inspections and tests of such machines has been described in Bureau of Mines Bulletin 305, Inspection and Testing of Mine Type Electrical Equipment for Permissibility, published in 1929. A more detailed knowledge of the special safety features of a particular machine is often useful and sometimes essential for inspectors, safety engineers, maintenance men, and engineers in selecting machines for a particular application. Three bulletins that give information of this nature have been-published by the bureau, viz., Bulletin 313, Permissible Storage-Battery Locomotives and Power Trucks. Bulletin 343, Permissible Coal-Handling Equipment. Bulletin 382, Permissible Coal-Cutting Equipment. Report of Investigations 3309, Permissible Electrically Operated Air Compressors, which contains similar information, was issued in August 1936, and a Report of Investigations 3326, Permissible Electrically Operated Room Hoists, was issued in January 1937. Thus, the present paper is the third to give detailed information concerning permissible machines of types not included in bulletins, and covers all the rock-dust distributors approved prior to October 1, 1936.

Jan 1, 1937

By W. W. Weller

Heat-capacity measurements of sodium dimolybdate (Na2Mo207) and sodium ditungstate (Na2W207) were conducted over the temperature range from 51° to 298° K. The entropies of the two compounds at 298.15° K were calculated from the heat-capacity values and were used, in conjunction with other entropy data, to evaluate the entropies of formation of the compounds from their constituent elements and oxides.

Jan 1, 1963