Search Documents

By D. E. Kirby

In line with the Bureau of Mines' goal of providing technology to maintain a supply of minerals adequate to meet national economic and strategic needs, a method for recovering chromite from lateritic materials was investigated. Laterites are a large resource of Ni, Co, and Cr, critical metals of which the United States has insufficient domestic sources. A roast-leach method was developed by the Bureau to extract nickel and cobalt from domestic laterites. A concurrent effort was made to recover chromium from either unprocessed laterites or the leach residues. This report characterizes laterites and laterite leach residues. It describes a chromite recovery procedure using conventional industrial beneficiation equipment for sizing, low-intensity magnetic separation, and gravity concentration. Concentrates containing 20.0 to 22.4 pct Cr (29.0 to 32.7 pct Cr203) and with a 1.6:1 to 1.9:1 Cr-Fe ratio were recovered from laterites and residues containing 1.3 to 2.5 pct Cr with recoveries exceeding 50 pct. Because of their low grade and fine size, these concentrates would be suitable for preparing chromium chemicals. The direct beneficiation of laterites for chromite recovery resulted in the minerals containing nickel and cobalt concentrating in slime products. No iron oxide coproducts of acceptable grade were recovered from either laterites or residues.

Jan 1, 1982

By Paul C. McWilliams

The U.S. Bureau of Mines has, primarily through its contract program, used large-scale centrifuges to determine design criteria for tailing embankments. The centrifuge runs were made at two installations, the University of Cambridge, Cambridge, England and Sandia National Laboratories, Albuquerque, NM. The major problems considered were as follows: slope stability of embankments, modeling erosion and seepage, use of the phreatic surface level to ascertain the validity of centrifuge modeling, and the effects of compaction and weathering on a tailings embankment. This report summarizes the results of the four test series conducted at University of Cambridge and Sandia National Laboratories. A review of prior centrifuge applications to mining problems is included. Consideration is given to future centrifuge application to mining problems in both soil and rock mechanics.

Jan 1, 1989

By C. Ozgen Karacan, William P. Diamond

In This Chapter [Measuring the gas content of coal Predicting gas emissions based on geologic and coal reservoir property data Determining the gas storage capacity of coalbeds and other gas-bearing strata Methane drainage borehole monitoring to forecast the remaining gas-in-place and the influence on mine emissions Forecasting gas emissions during mining as a function of mining parameters and Gas emission prediction based on numerical simulation] This chapter provides guidelines for determining the gas content of coalbeds, estimating the gas-in-place, and predicting gas flow and emissions before and during coal mining operations. The techniques are discussed briefly in the following sections. However, detailed information on the techniques is provided in the cited references. INTRODUCTION Coalbed methane, if not properly controlled in the underground mine environment, is a safety concern due to the potential risk for an explosion. This is a particular problem during longwall mining, where the high rate and volume of coal extraction can result in the release of large amounts of methane from the mined coalbed and other adjacent gas-bearing strata. The variability and potential hazards of these sometimes unexpectedly high gas flows provide the impetus to develop methods to predict methane emissions into the underground workplace. A forecast of the volume of gas that might be released during coal mining is helpful for designing ventilation systems and for implementing optimum methane drainage strategies to help mitigate expected gas emission problems. A complete assessment of the need for methane drainage prior to mine development generally requires both an empirical and a theoretical approach. If there are active mines in the general area with similar geologic conditions and coal characteristics, a review of gas problems in those mines provides an initial insight into the level of gas emissions to be expected at a new location. In addition, relatively simple methods exist to determine the in situ gas content (volume of gas per unit weight of coal) of the coalbeds in a particular mining area, as well as the gas-in-place (volume of gas in the coalbed(s) within a defined geographic area).

Jan 6, 2006

Eliminate accidental tramming of a cleanup tractor. Approach A switch was installed in the operator's seat cushion to pre-vent the cleanup tractor from tramming without an operator in the driver's seat. How It Works The operator must be seated, and the Forward/Reverse Switch (that controls tramming direction) must pass through the NEUTRAL position before the vehicle will tram. See Figure 1. A pressure-sensitive seat cushion switch, a solid-state relay, and a double-contact relay were added to the control circuitry of an S & S BMUAT -88 cleanup tractor to create this tramming interlock. The weight of the operator on the cushion closes the seat cushion switch (Figure 2, A). This activates the solid-state relay (B), which completes the initial circuitry. Moving the For- ward/Reverse Switch (C) to NEUTRAL energizes the coil in the double-contact relay (D) and closes both contacts. One contact completes a sustaining circuit which keeps the double-contact relay energized. The second contact transfers power to the remaining contacts within the Forward/ Reverse Switch. These circuits are shown in greater de- tail in Figure 2.

Jan 1, 1978

By John Hays Hammond, James Douglas, J. PARKE CHAN- NING, W. R. Ingalls, J. R. Finlay

The committee making this report, consisting of Walter Renton Ingalls (chairman), J. Parke Channing, James Douglas, James R. Finlay, and John Hays Hammond, was originally appointed at a meeting of the American Mining Congress at Denver, Colo., in No- vember, 1906. The object of this appointment was the drafting of a modern law governing quarrying and metalliferous mining which could be recommended to the several States for adoption, in the hope that the passage of such a uniform law by the mining States would tend to lower the number of fatal and serious accidents. The first step of the committee (the personnel of which has re- mained unchanged from the beginning) was to procure copies of existing laws from the officials of the several States of the Union. With the assistance of the Engineering and Mining Journal, copies of the laws of Great Britain, the Transvaal, New South Wales, Victoria, Queensland, Western Australia, Tasmania, New Zealand, and certain European countries were also obtained. The replies to the inquiries made at that time developed the fact that a number of States in which mining was carried on had no laws at all. Other States were found to have elaborate provisions regulating coal min- ing, but none applying to metalliferous mining. Still other States were found to have miscellaneous and unrelated provisions passed at odd times, seemingly as the result of the occurrence of some dis- aster or other.

Jan 1, 1915

Prevent collisions between large mine-haulage trucks and smaller vehicles parked in areas not visible to the haulage-truck operator, Approach Two electronic systems were developed to detect the presence of vehicles in the blind areas of a parked haulage truck. The systems can warn haulage truck operators of presence of vehicles that are blocked from view. The systems do not apply for trucks in travel. How It Works The systems use electronic transmitting techniques-one system is based on low-frequency radio waves and the other on very-high-frequency radio waves. Each system requires that a signal transmitter be mounted on the smaller vehicle to be detected. Continuous signals from this transmitter are sensed by receiving antennas mounted on the right front and rear of the large haulage truck. Upon receiving a signal, the receiver energizes warning lights and a buzzer in the cab of the haulage truck, alerting the operator to a possible collision hazard. Detection distance is adjustable, depending upon the size of the haulage truck, but a minimum of 30 feet was the design goal.

Jan 1, 1990

By Eric S. Weiss, Deno M. Pappas, Timothy M. Barton

During the past few years, the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health (NIOSH) has been evaluating developments in sealant support systems from a ground control perspective. The proper selection and use of a sealant material can significantly enhance ground control which may result in a decrease in worker related injuries due to ground falls. The purpose of this paper is threefold: to briefly review the current state-of-the-art technology in shotcrete and membrane developments, to evaluate the preliminary findings of a long-term underground study of various types of sealant materials, and to examine installation practices that are critical for an effective sealant material. The underground study utilizes NIOSH’s Lake Lynn Laboratory Experimental Mine to evaluate the long-term performance of several types of shotcrete and membrane materials. Sealant performance to date have been evaluated on a regular basis over a two year period. Although the study is still ongoing, critical mining practices were identified that may seriously effect the bond of the sealant materials to the mine roof and rib; most notably, the importance of scaling and thorough cleaning of the rib prior to application. Also, results froman extensive series of Schmidt Hammer tests found that the shotcrete increased in strength by 70% during the humid summer months.

By William P. Diamond

Ventilation has long been the primary means of controlling methane emissions in underground coal mines. However, as mining has progressed into gassier areas of U.S. coal basins, supplemental means of methane control have become of interest, if not a necessity, for continued safe and productive mining operations. This paper describes the history and technology of methane drainage in the United States and other countries. The methane drainage technology developed in European countries is a valuable resource since their longer history of mining has already forced mine operators to deal with methane emission problems only now being experienced in the United States. Methods for assessing the need for methane drainage and the data required for planning and implementing an appropriate system are reviewed. The effectiveness of the various technologies for reducing methane emissions underground and/or the in-place gas content of individual coalbeds is illustrated with case studies. In addition to the safety and productivity gains to be realized from methane drainage systems, the potential for commercialization of coalbed methane is discussed.

Jan 1, 1994

By H. Carroll

An ozone detector was built and evaluated for its applicability in smog-chamber studies. The detection method is based on the reaction of ozone with ethylene and the measurement of resultant chemiluminescence. In the first phase of evaluation, the detector's response to ozone was studied as a function of several instrument parameters, and optimum conditions were defined for the maximum and most stable responses to ozone. In subsequent evaluations, the method was checked for sensitivity, precision, and interferences and was compared with two alternative methods. Results showed the chemiluminescence method to be acceptably sensitive and precise for smog-chamber studies and superior to the Mast ozone meter and KI (colorimetric 1 percent neutral-potassium iodide method) methods in that it is specific for ozone.

Jan 1, 1972

By Charles Vaught, Kathleen M. Kowalski

Safety and health professionals from all sectors of industry recognize that training is a critical element of an effective safety and health program. A major concern in the mining industry is how to train both an aging workforce and the expected influx of new miners and mine managers as older workers retire. Thus, a review of some of the basic principles of adult learning may be helpful to mine trainers. This paper discusses the principles of adult learning based on research in education and psychology. It stresses the importance of taking a systems approach to training, focusing on the relationship between the environment and technology, and understanding how workers interact with both. The authors argue that the principles of adult learning and a systems approach are fundamental to the delivery of effective training in the mining industry. Examples of training programs developed by the Pittsburgh Research Laboratory of the National Institute for Occupational Safety and Health are presented within two broad performance domains: routine and nonroutine skills. Basics of curriculum development are also briefly presented to provide the mine trainer with a template for program development.

Jan 1, 2002

By William L. Porter

From the first day of new miner training until the day they retire, mine workers will experience changes due to the normal aging process. It is an unfortunate fact of life that many age-related changes result in diminished physical, sensory, or cognitive capabilities. Of course, workers also gain a tremendous wealth of experience, knowledge, and insight as they age, making them a vitally important resource for their company. Effective leveraging of this precious resource requires both an appreciation of the changes that occur with age and an understanding of methods that can be used to reduce the injury risk that may result. The purpose of this training is to provide the information necessary to accomplish these objectives. Aging workers may not necessarily have a higher injury risk overall; however, the effects of a musculoskeletal injury (MSI) on older workers may be more extreme. MSHA data show that not only does the percentage of MSIs increase when workers are over age 30, so does the number of days lost per injury, as shown in the graph below [MSHA 2005]. [ ] Protecting the safety and health of aging workers requires matching the demands of the job to worker capabilities. This means reducing or eliminating risk factors for injuries, such as heavy lifting, awkward postures, static postures, repetitive movements, and/or vibration exposures. In other cases, it may mean improving visibility or streamlining processes. Designing jobs to accommodate the changing capabilities of older workers will not only reduce injury risk for older workers, it will have the added benefit of protecting younger employees as well.

Jan 1, 2008

By A. J. Farstad, R. F. Kehrman

Characteristics of metal/non metal mines were evaluated to determine the suitability of applying the U.S. Bureau of Mines electromagnetic location system to the problem of locating trapped driers in metal/non metal mines. Statistical distributions of mine depths and overburden conductivities show that the existing USBM EM system is inadequate for most metal/non metal mines. Alternate approaches to trapped miner location in deep mines were identified and subsequent field tests were conducted at six (6) mines to evaluate their feasibility. The approach considered to be the most promising is one which utilizes the existing manpack transmitting system, modified slightly for a dual frequency output, in conjunction with a sophisticated signal processing receiver on the surface. The main advantage of staying with a "through the earth" approach is that the underground equipment can be kept simple, easily maintained, light- weight and inexpensive.

Jan 1, 1979

By Wilbur I. Duvall

Surface vibrations of ground, rock, and structures resulting from blasting or other sources are often measured with portable seismographs. These instruments are usually supported by a three-point mount or tripod which is simply placed on a horizontal surface on which vibration levels are to be measured. The rigid-body motion of a tripod-supported seismograph is considered from the point of view that there should be no slippage of the feet with respect to the surface and none of the feet should leave the surface as a result of imparted motion. From these studies the following design criteria are deduced which assure that the seismograph will respond accurately to vibration levels as large as 1/2 g.:3/ First, the coefficient of friction between the feet and the surface on which the instrument rests should be as large as possible, preferably approaching unity; second, the center of gravity of the instrument should be vertically above the centroid of the three-point mount; and third, the vertical distance between the center of gravity of the instrument and the centroid of the three points of contact with the surface should be less than the perpendicular distance between the centroid point and anyone of the three sides of the triangle formed by the three points of contact. Portable seismographs that do not satisfy these conditions should be clamped to the surface if vibration levels above 0.1 g. are to be recorded.

Jan 1, 1961

Roof falls continue to be the greatest single safety hazard faced by underground coal miners. During 1996-99, 44 coal miners lost their lives in rock falls, and nearly 2,400 were injured. In addition, nearly 6,000 noninjury roof collapses were reported. Roof supports are installed to protect the miners, but support system failures contributed to most of these incidents. Reducing the terrible toll taken by ground falls continues to be a major goal of research by the National Institute for Occupational Safety and Health (NIOSH). The purpose of these proceedings is to provide the mining community with a comprehensive survey of coal mine roof supports. Drawing on many years of research undertaken by the NIOSH Pittsburgh and Spokane Research Laboratories, this volume describes what types of support are available, how they work, and when they should be used. The major subjects covered include roof bolts, standing roof supports, cable supports, and longwall shields. Some special topics are also addressed, including an analysis of roof fall accident statistics, techniques for better skin control, material handling considerations, and longwall mining through recovery rooms. This proceedings volume also contains information on several important new technologies, which are described here for the first time: •Guidelines for selecting roof bolt length, pattern, and capacity that were derived from statistical analysis of the roof fall experience at 37 underground mines; •A new design method for longwall tailgate supports; and •A technique for measuring loads developed within cable bolts. The papers in these proceedings were presented at open industry briefings conducted by NIOSH on New Technology for Coal Mine Roof Support. The briefings were held in Norton, VA, Charleston, WV, Evansville, IN, Tuscaloosa, AL, Price, UT, Glenwood Springs, CO, and Washington, PA. The papers were also presented at the Mine Safety and Health Administration (MSHA) Preventative Roof-Rib Outreach Program (PROP) Seminar, which was held at the National Mine Health and Safety Academy near Beckley, WV.

Jan 10, 2000

By Carl Sunderman, Steve Signer

Researchers at the National Institute for Occupational Safety and Health (NIOSH) have developed several new tools for evaluating roof support performance. A miniature data acquisition system (MIDAS) was developed that can collect readings from up to 16 strain gauges at regular time intervals and store the readings for later retrieval. Three LED lights change from green to yellow, then red, based on the reading levels and/or rates of change of rock movement. This feature can be used to warn miners of rock instabilities. The system can be used with any strain-gauged support (resin bolt, friction bolt, cable bolt) or with a newly developed rock strain strip (ROSS) developed by NIOSH to measure rock strain. A ROSS is grouted in a hole drilled adjacent to the rock support to be evaluated; the deformed shape of the ROSS provides anchorage on either side of the strain gauges. Data from both laboratory tests and field evaluations are presented that describe the capabilities of both the MIDAS and ROSS instruments.

Reduce shaft sinking costs and workers exposure to mechanical hazards, drill dust, blast dangers, and fumes. Approach Replace drilling and blasting by using a large, cab-mounted impact breaker suspended from the bottom work deck of the galloway. How It Works The pneumatically actuated impact breaker is positioned by an articulated boom con-trolled from an operators cab. The breaker delivers 2,000 ft-lb blows that fragment the rock at the shaft bottom. Mucking is accomplished by a backhoe bucket on an articulated boom mounted on the cab. See photograph. The mucked material can be removed either by dumping into a previously drilled borehole or by being lifted out in a muck bucket as shown in the drawing. Positioning of the breaker, rotating the cab around its vertical axis, and moving the cab support frame around the perimeter of the shaft are all controlled by one joystick. Separate controls position the mucker boom, which can be swung horizontally through a 180° degree arc towards either side of the cab. Because the cab can be rotated to any position around its vertical axis, and can also be moved in a horizontal circle around the shaft, virtually any position on the bottom of the shaft can be reached by the breaker and mucker.

Jan 1, 1981

By Arnold P. Pipilen

In a study of the principal factors affecting the transport of coal-water mixtures through a centrifugal pump and a pipeline, the interrelation between solids concentration, velocity, and pressure drop was established for a bituminous lump coal (minus 2 inch) in concentrations up to 48 weight-percent. An optimum concentration was found to exist for maximum capacity of a given pipe-line, and for minimum energy requirements per ton of coal. Coal size degradation by particle fracture took place in the pump; abrasion and attrition to form fines took place in both pump and line. A novel system of studying flow of solid-liquid mixtures in pipelines by the determination of relative sound intensities was developed.

Jan 1, 1966

By R. Karl Zipf

A method is presented for creating realistic numerical models for practical coal mine ground control. The method includes procedures to collect the necessary mechanical input parameters from a geologic core log, procedures to set up a model, and procedures to interpret calculation results. The input parameters come from a detailed geologic core log and extensive point load tests of estimate rock layer strength. A suite of material property input parameters is proposed that allows the user to go from core log to numerical model inputs. Rock bolt anchorage properties are also linked to the material properties of each geologic layer in the model. Following this procedure leads to very realistic calculations of the rock failure process and rock support system behavior. These calculations in turn enable realistic comparison of the effectiveness of alternative rock support systems.

Jan 5, 2007

Reduce well construction and operation costs associated with in situ leach mining while increasing mineral recovery. Approach To accommodate the size of centrifugal pumps presently in use, in situ leaching production wells are typically drilled to 6 inches in diameter, while monitor wells are drilled to measure 4 inches in diameter. However, in order to reduce the cost of drilling these larger diameter wells and to increase recovery, the Bureau has developed jet pumps which have smaller diameters than centrifugal pumps of the same capacity. This allows both production and monitor wells to be drilled smaller. Bureau estimates indicate that the cost of drilling a 3-inch-diameter production well at in situ leaching operations would be about 35 percent less than the cost of a 6-inch well. Similarly, the cost of drilling a 2-inch-diameter monitor well would be about 26 percent less than the cost of a 4-inch well. Such significant savings in the cost of drilling these wells would effect a substantial reduction in total capital cost. Use of the new jet pumps can also increase the percentage of recovery because less costly wells allow closer well spacings, improving the distribution of the leach solution. How the System Works After the borehole is cased, the new small-diameter jet pump, along with piping and accessories, is installed and connected to a centrifugal pumping unit on the surface. High-pressure water from the surface pump is forced through a nozzle into the venturi of the jet type pump injector. This jet action lifts the leach and mineral-bearing solution to the surface.

Jan 1, 1984

To separate complex mineral mixtures according to their dielectric properties. Approach Develop a laboratory-scale continuous dielectric separator to separate mineral mixtures by exploiting their difference in dielectric properties. How it Works Dielectric separation is de-fined as the separation of particles based on their dielectric properties. The uniqueness of the Bureau's continuous separator, called the ?Rotating Drum Dielectric Separator,? is that it contains a high-voltage electrode con-figuration. The drum electrode consists of a series of coaxial parallel wires mounted on the outside surface of an Insulated cylinder. The screen electrode Is a wire mesh, quarter cylinder positioned outside and coaxially with the drum electrode. The drum electrode is placed in a liquid of dielectric constant K with the liquid level just above the drum's axis. The screen electrode is completely Immersed

Jan 1, 1981