Search Documents

By M. P. Board

The U.S. Bureau of Mines, under a cooperative agreement with Hecla Mining Co., conducted a rock mechanics study at four widely spaced horizons in a deep mine shaft in northern Idaho. The objective of the project was to measure and analyze rock deformation and lining behavior during construction of a deep shaft in a high in situ stress field within an isotropic rock mass. Rock mass displacements were monitored with multiple-position borehole extensometers. Liner stress and strain were measured with concrete pressure cells and embedment strain gauges. This report discusses the general trends and magnitudes of data from the four test sites, and relates the data to a proposed anisotropic constitutive model for the rock mass. A design procedure is then outlined for specifications of liner thickness and support installation sequences for future shaft sinking.

Jan 1, 1989

By M. M. Gilkey

Pegmatites in Colorado occur for 150 miles along the Front Range (eastern-most range of the Rocky Mountains) from Larimer County on the north to Canon City on the south, and west into the Gunnison area. Many of the deposits have been classified. Minerals found in the various dikes include beryl, scrap and possibly punch mica, lithium-bearing minerals, columbite-tantalite, feldspar, and several rare minerals. Pegmatites are abundant in the Crystal Mountain district in Larimer County. About 5 miles south of the Crystal Mountain district and often identified with that district is the Hyatt pegmatite area. The Hyatt Ranch deposit has attracted particular attention because of the comparatively high beryl con-tent of the upper part exposed in opencut workings.

Jan 1, 1960

By Richard L. Ash

Introduction The blasting capabilities of commercial explosives are often rated according to their loading densities and detonation velocities. Both the density and velocity are relatively easily measured, the values of which can be used for determining the approximate detonation pressure developed by an explosive during any given set of blasting conditions (1-5). Knowledge of the actual rate of detonation attained at all points along a charger's length also is considered to give a good indication of how well the explosive is functioning. Many factors affect the density and velocity and have been thoroughly discussed by various authors (4, 6-12). For recording velocities several methods are available, but the resistance-wire, or probe, continuously recording technique has the distinct advantage of providing a record of the complete progress of an explosive reaction from the time it first initiates. Figure 1 is a copy of a typical record obtained by the procedure with certain significant information indicated. The theory and applications of the method are extensively covered in the literature so need not be reviewed for this report (13-18). Only the specific equipment and procedure employed for this investigation are presented.

Jan 1, 1973

This report is the 26th in a series summarizing Bureau of Mines research and technologic work on coal and related investigations and the 8th of these reports to be issued on a calendar-year basis.1 It reviews briefly work in progress during 1961, and it provides references to publications by Bureau personnel during 1961 and also to a few older papers that were not cited in prior reports of this series. Details about some of the researches mentioned may be obtained by referring to the publications cited in the footnotes or in the further list in the Bibliography; other phases of work are reported here for the first time and will be covered in more detail by later publications.

Jan 1, 1963

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and 2-year time periods during 1990-1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 1, 2004

By Maria I. De Rosa

This report analyzes mine fires for all U.S. underground and surface coal mining categories by state and2-year time periods during 1990–1999. Risk rate values are derived, and ignition source, methods of fire detection and suppression, and other variables are examined. The data were derived from Mine Safety and Health Administration (MSHA) mine fire accident publications and verbal communications with mine personnel. The analysis will provide the National Institute for Occupational Safety and Health, MSHA, and the mining industry with a better understanding of the causes and hazards associated with mine fires and will form a basis for future fire research programs.

Jan 9, 2004

Under contract from U. S. Bureau of Mines, Harza Engineering Company in cooperation with Eastern Associated Coal Corporation, conducted a ground control study of two mechanized longwall panels at the Federal Number 2 Mine. The mine is located in Northern West Virginia, and the coal is mined from the Pittsburgh Coal Seam. The prime objective of the study was to collect data which will aid in the proper selection of the longwall supports system and to control the entry caving problem. Instruments installed in the mine were borehole pressure cells, convergence recorders, roof sag recorders, horizontal roof strain indicators, differential floor movement systems, and lateral roof and floor movement systems. Instruments installed on the surface, above the instrumented longwall panels, consisted of slope indicator system, vertical bed settlement probe system and shear displacement detecting system. A comprehensive surface subsidence study was conducted in conjunction with the instrumentation. In addition to the instrumentation and monitoring, special tests were conducted to determine the bearing capacity of the roof and floor rocks, in situ modulus of coal, roof and floor rocks, and response of borehole pressure cells to ground stress. Cores of coal measure rocks were collected for the physical property tests. Face observations were made to detect various roof behavior parameters under the different jack setting pressures. This report essentially describes the instrumentation work, special tests and presents the data collected.

Jan 1, 1976

By Clarence O. Babcock

This Bureau of Mines publication presents guidelines for mining near surface and underground bodies of water. The guidelines were based on information developed under contract in three phases of study, as follows: (1) Collection and documentation of data from worldwide sources; (2) application of existing guidelines, foreign, Federal, and State, to case histories of previous inundations; and (3) development of recommended guidelines for underground coal mining near bodies of water aimed at maximum efficient utilization of underground coal resources consistent with minimizing inundation hazards. While the contract guidelines were for the mining of coal seams, they may also be used for mining any tabular sedimentary mineral deposit. Tables are given for the determination of the size of coal pillars needed; for other bedded deposits, similar tables could be determined based on their strength properties.

Jan 1, 1977

By Joe Maher

[ ]

Jan 1, 1976

By R. V. Ramani, R. Stefanko, G. W. Luxbacher

TEST DECK – ALTMETER SURVEY WITHOUT PLTTMETER TEMPERATURE CCRRECTION DATA INPUT

Jan 1, 1977

By P. M. Johnson

A design for a laser-powered optical interferometer, using a specimen whose thermal expansion is to be measured as part of the optical system, was conceived and applied in a prototype dilatometer. The object of thin work was the development of an absolute dilatometer capable of use at elevated temperature, particularly above 1,000° C. The prototype has been operated at temperatures exceeding 1,510° C. Results obtained with this device agree within 2.5 percent with the published data for the coefficient of expansion of columbium.

Jan 1, 1968

By Douglas F. Scott

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied an 11,980-acre part of the 33,300-acre High Rock Canyon Wilderness Study Area, CA-020-913B, in order to evaluate its identified mineral resources. No mineral resources were identified during this study, and no significant amounts of gold, silver, mercury, gem-grade opal, or placer gold are present. The study area is located in Washoe County, NV, about 53 miles southeast of Cedarville, CA. No mining districts or mineral production are known, and no oil and gas leases are in the area. No current claims are in the area; however, six placer claims were located in 1911 in High Rock Canyon near its confluence with Mahogany Creek.

Jan 1, 1987

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most, States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the Oklahoma Planning and Resources Board of the Conservation Commission has been authorized to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Sam S. Taylor

Subsurface disposal of oil-field brines was practiced in Oklahoma on a limited scale as early as 1925. The technique of subsurface injection has been improved immensely and has been applied with varying success in many oil-producing areas in Oklahoma, and elsewhere. This method of disposal, however, is only one of several methods available to operators of oil-producing properties, but, in contrast with usual methods of handling brines on the surface it eliminates the damaging effect of mineralized water on fresh-water supplies, vegetation, and aquatic and other animal life. Other methods of brine disposal approved by regulatory agencies in some States include (1) impounding in impervious ponds and solar evaporation, (2) controlled diversion into surface waters, and (3) recovery of the mineral salts of the brine. In most States where oil is produced regulatory bodies authorize the use of one or more of these methods of brine disposal. In Oklahoma, for example, the .Oklahoma Planning and Resources Board of the Conservation Commission has been authorized4/ to adopt whatever methods or means may be necessary to prevent contamination by mineralization of all potable waters within the State.

Jan 1, 1942

By Jeffrey Kohler, John J. Samrnarco, Thomas Novak, Lloyd Morley

Equipment control functions that were once hardwired are being implemented with software and very large scale integrated (VLSI) devices. Often this transition has resulted in increased flexibility, improved quality, and decreased costs. At the same time, it has created new concerns and challenges concerning worker safety. The visible and well-defined ladder diagram for relay-logic has been replaced by program in which the exact outcome for varied inputs can be more obscure. In the coal mining industry,-efforts to automate longwall mining systems hove resulted in semiautonomous machines operating within the same space as workers This paper describes an effort initiated by the National Institute for Occupational Safety and Health (NIOSH to identify the safety rules related to the use of processor-controlled equipment in mining. Specific findings in the areas of human factors, hardware, and some safety are presented in this paper, and a brief description of a plan to address identified weaknesses is given.

By O. C. Blade

Sales of diesel fuel in the United States during the post year and a half have increased greatly. In 1955 over 174 million barrels were sold of which 80 million (or 46 percent), were used by the railroads, and over 44 million barrels (25 ½ percent) of the fuel were used in trucks, busses, tractors, and heavy moving equipment. Vessels (12 percent), industry (9 ½ ), the military forces (4 ½ ), power plants (2), and oil companies (1/2 percent) account for the remainder. 2/ Dally deliveries of diesel type fuel from refineries averaged over 16,750 barrels during the first six months of 1956 in comparison with 15, 250 barrels during the corresponding period of 1955. 3/ Information on the properties of diesel fuel is very important to the petroleum industry, engine manufacturers, and consumers. To supply such information the American Petroleum Institute and the Bureau of Mines, United States Department of the Interior, under cooperative agreement, are conducting annual surveys of diesel fuel oil produced in refineries in this country.

Jan 1, 1957

The safety analysis of shaft-sinking operations included a review of accident reports from coal and metal-nonmetallic mine shaft-sinking projects in the United States, a review of foreign and domestic shaft laws, and discussions with shaft contractors and Federal mine inspectors. Accident data were studied to identify the most common and the most severe types of shaft accidents and to determine their immediate and contributing causes. Additional factors such as worker training and experience, equipment and sinking procedures, regulations and enforcement practices were also investigated to determine their impact on shaft safety. The results of the study are summarized in recommendations for improved training of shaft miners and clarification of Federal shaft-sinking regulations. A guide to assist mine inspectors in examining shaft-sinking projects is also included.

Jan 1, 1977

By J. O. Winget

Amino acids were investigated in conjunction with rare-earth separation by ion exchange to determine whether they can be utilized effectively as retaining agents for metals separation using ethylenediaminetetraacetic acid (EDTA) eluant at 85° to 90° C. Hydroxyethylethylenediaminetriacetic acid (REDTA) and diethylenetriamine pentaacetic acid (DTPA) were the most effective amino acids investigated. Elements of atomic numbers 39 and 57 through 68 were effectively retained, whereas elements of atomic numbers 69 through 71 passed through the retaining-agent band. Utilization of REDTA or DTPA retaining agents allows an increase of 75 percent in the EDTA eluant concentration over that possible with hydrogen-or copper-retaining ions without precipitation occurring. Eighty-five percent recovery of the EDTA eluant collected before rare-earth breakthrough and during elution of lutetium, ytterbium, and thulium, and essentially complete recovery of the REDTA or DTPA retaining agents, are possible without extensive processing.

Jan 1, 1968

This report is the 24th in a series summarizing research on coal and related investigations3 by the Bureau of Mines. The coal programs of the Bureau of Mines include a wide range of theoretical and applied studies--such as fundamental studies of coal structure and properties, the development and evaluation of new mining techniques, and work toward more effective processing and utilization of coal. The scope of these programs is indicated, in topical outline, by the table of contents. These investigations are integrated into a broad but coordinated effort to develop information on coal that will benefit the coal mining industry and the coal consumer while promoting the wise conservation and utilization of our national coal resources. Any attempt to summarize in one volume the progress in all of the program areas indicated must necessarily be limited to a brief review of developments, without detailed reporting of the data. However, while the brief discussion in each section will present only the highlights of the Bureau's work during the year, details of many of the operations or investigations described here can be found in the publications cited throughout the text. Other work, reported here for the first time, will be covered in greater detail in later publications.

Jan 1, 1962

By Terry R. Neumann

During 1983, U.S. Bureau of Mines personnel examined mines, prospects, and mineralized zones to evaluate the mineral resources and potential of the Funeral Mountains Wilderness Study Area (WSA), Inyo County, California. Eleven mineral properties and two mineralized zones were examined during this study. Of these, six are within the study area and seven adjacent. There are no active mines, in the WSA, nor is there evidence of past production from any claim within the study area. The WSA contains no identified mineral resources. However, occurrences of bentonite, zeolites, and strontium were found in the area. There is little likelihood for resource development of any occurrence in the WSA. The area, in the Basin and Range Physiographic Province, is dominated by a Paleozoic marine sequence. Segments of Tertiary continental fluviolacustrine sediments, including volcaniclastic rocks, abut and overlie the Paleozoic rocks in fault controlled basin areas. Significant concentrations of bentonitic clay and zeolites occur as alteration products in Tertiary tuffaceous sedimentary rocks. However, they are generally low-grade, thin, and discontinuous, precluding commercial development. Limestone, quartzite, and sand and gravel in the area are suitable for many types of construction uses, but similar deposits outside the WSA are closer to markets. No energy resources have been identified in the WSA.

Jan 1, 1984