Search Documents

By Neil B. Young

Analytical results for nahcolite, dawsonite, total extractable alumina, and oil yield are presented for samples representing Green River Formation oil shales in the saline section of two cores from Colorado's Piceance Creek basin. Analyses are also reported for samples extending the analyzed section of Colorado corehole No. 3 beyond that reported previously. These data permit evaluation of the deposit for possible production of three coproducts--shale oil, alumina, and sodium carbonates--from the saline section of the formation at these sampled points.

Jan 1, 1970

By Robert W. Freedman

This report describes sampling and analytical procedures used for measurement of sulfates in diesel tailpipes and in the diluted exhaust within dilution tunnels. A variety of methods exist for sulfate analysis for such systems, including ion exchange. Two chemical methods used by the Bureau of Mines are described in detail. These are based upon spectrophotometric measurement of chloranilic acid using barium chloranilate. The procedures are rapid and relatively inexpensive. In general, ion exchange is preferred by many analysts for sulfate analysis. However, it is more complex and expensive than chloranilic acid procedures, which are adequate for exhaust analysis.

Jan 1, 1982

By E. H. Denny

In discussing safety in Colorado metal mines there are two important points for metal -mining men to consider , namely , the direct and indirect cost of accidents and the possibility and means of preventing accidents . For statistics on Colorado metal - mine accidents , reference has been made to published reports of the United States Bureau of Mines on metal- mine accidents from 1919 to 1927. This period was considered because only with the year 1919 are complete figures on nonfatal accidents available and because these years represent postwar activities ; 1927 is the last year for which the U. S. Bureau of Mines has published accident statistics . During the nine -year period 1919 to 1927 , inclusive , 153 metal miners were killed by mine accidents in Colorado and 5,035 miners suffered lost - time injuries . The accidentfrequency rate of number killed per 1,000 300- day workers for this nine - year period was 4.68 as compared with the general average of 3.26 for all the metal mines of the United States for the same period . In other words , the fatality rate in the metal mines of Colorado for this nine- year period averaged 40 per cent higher than that of the metal- mining industry in the United States generally . In 1924 and 1926 the Colorado metal mines had a better accident record than the average of those of the United States , but 1927 was a bad accident year and the State Bureau of Mines figures for 1928 and 1929 showing respectively 18 and 23 men killed in and about the metal mines indicate a continuing relatively high death rate from accident . The cost of accidents to the miner for the period 1919 to 1927 can be estimated from the accident figures just given . The United States Bureau of Mines as well as other authorities assess 6,000 days lost time for every fatality and every permanent total disability . These authorities have also agreed that a permanent partial disability costs 800 days lost time to the worker over his working lifetime , that lost time injuries of less than 14 days average about 6 days lost time and lost time injuries not involving permanent disability but having loss of more than 14 days average 32 days lost time . On this basis the Colorado metal miners have suffered in nine years a gross loss of 1,214,146 days , or , at $5 per day , $6,070,730 . The miner receives about one -ninth of this amount in compensation so that the net loss to the metal miner in Colorado for this nine - year period was about $5,400,000 .

May 1, 1930

By Donald N. H. Chi

The unsteady, one-dimensional, compressible-flow equations have been solved numerically for a deflagration propagating through a gallery of finite length closed at the ignition end and open at the opposite end. These equations were solved for two situations wherein (1) the propagating flame was extinguished after 0.1 sec or before the return of aerodynamic disturbances reflected from the open end, and (2) the flame was allowed to propagate a full 0.8 sec until it was extinguished. It was found that the process of sudden flame extinguishment creates rarefaction waves that, upon entering the burned zone, produce resonance within the burned cavity. For the relatively small value of the product of the expansion ratio (8.5) and the effective burning velocities of 7.4 m sec-1 for the first experiment and 4.9 m sec-1 for the second experiment, it was found that the acoustic approximation provides an adequate estimate of the pressures developed ahead of the flame during the system's early history.

Jan 1, 1974

By H. D. Raymond

This report contains a summary of designs, specifications, costs, and schedules developed for a prototype oil-shale demonstration mining program to be undertaken at the Horse Draw site in the Piceance Creek Basin, Rio Blanco County, Colorado. The objective of the demonstration program is to assess the feasibility of extracting oil shale and associated saline minerals from deep, rich oil shale zones which occur within the central portion of the Basin. Four mining systems were specified for demonstration. These include (1) chamber and pillar mining with backfill; (2) sublevel stoping with backfill; (3) sublevel stoping with full subsidence; and (4) block caving. Commercial-scale designs for each system were modified and scaled down as required to achieve program objectives. The demonstration mine layout and design includes specifications for ore handling, backfilling, ventilation, dewatering, maintenance, and supply systems. A feature of particular interest in the design is the combination of block caving and sublevel stoping methods into a single unit for demonstration of subsidence mining systems in deep oil shale deposits. The report also contains a detailed breakdown of projected capital and operating costs for the demonstration mining program.

Jan 1, 1979

By W. W. Adams

The quantity of explosives sold in the United States in January, 1931, for domestic consumption, amounted to 368,100 kegs (9,202,500 pounds) of black blasting powder, 4,610;000 pounds of permissible explosives, and 16,533,000 pounds of high explosives 'other than permissible. These figures are based on reports received by the United States Bureau of Mines, Department of Commerce, from nearly all manufacturing companies, and include an estimate of sales by several companies that do not furnish monthly reports. Reports actually received from manufacturers showed soles of 365,977 kegs of black blasting powder (consisting of 220,892 kegs of granular powder and 145,085 kegs of pellet powder), 4,687,900 pounds of permissible explosives, and 15,496,152 pounds of high explosives other than permissible. Sales in January, 1931, were smaller than in January, last year, the decreases being 14 per cent for black blasting powder, 19 per cent for permissibles, and 17 percent for high explosives other than permissible. Sales in January 1931 when compared with soles in December 1930, show increases for all three classes of explosives as follows: 2 per cent for black blasting powder, 16 per cent for permissible explosives, and 7 per cent for other high explosives.

Jan 1, 1931

By Oliver Bowles

"Waste Granite in the Barre, Vermont, District: Waste in the great granite center at Barre, Vermont, consists of three types of material, the rough blocks rejected at the quarries on account of imperfections, the chips or spalls resulting from trimming and dressing at the cutting plants, and the granular and pulverized material from the dust collectors. The waste piles at the quarries of are immense proportions and constitute a serious handicap to quarrying in that they cover up good rock deposits, and are also so large that waste disposal becomes more and more expensive. The problem of utilization of such waste material is a topic of keen interest to all granite producers.Barre is not situated on a water route, and thus transportation costs prohibit the shipment of waste blocks for rip rap or ballast. Crushing plants use a small amount of this material for road construction, but aside from this, the waste is practically valueless.Investigators of waste utilization problems are awaiting with interest further information concerning an enterprise undertaken at Montpelier, Vermont, to utilize crushed granite for the production of brick similar to sand-lime brick. Granules of granite are mixed with lime, moulded, and hardened under steam Pressure, The brick produced are said to be of excellent quality for structural Purposes.There seems to be no logical reason why waste granite could not be utilized for the manufacture of building stone, and paving blocks, for many of the defects which condemn a stone for monumental purposes are not at all detrimental for building or street paving. F or the most part, monumental stone workers are not particularly interested in other branches of the granite in-dustry, and a combination of industries such as that suggested"

Jan 1, 1920

By Joan C. Biordi

[Composition profiles for atomic, radical, and stable species, as well as temperature and area expansion ratio profiles, have been determined for a nearly stoichiometric CH4-02-Ar flame and one to which 0.3 percent CF5Br inhibitor had been added. Net reaction rate profiles were calculated for all the observed species. For the normal flame, these and the mole fraction profiles gave rate coefficient information about the elementary reactions in the methane flame, for example, CH. + 0 4- H2CO 0 H, k4 = 1.05 X 1014CM3 mole-1sec-1 for 1,550§T 0,725' K; CO + OH 4 C02 + H, k6= 4.7 X 1011 for 1,350{T X1,750° K. Comparison between the inhibited and normal flame showed that A] and [CH3] were significantly reduced at the lower temperatures in the inhibited flame even though in the hot gas region the [E] [OH!, and [0] were essentially the same in both flames. The CF3Br disappears very early in the flame, relative to the fuel, and the reaction primarily responsible for its disappearance is H v CF3Br 4 HBr + CF3, where k7 is found to be 2.2 X 1014 exp(-9460/RT) for 700-1,550° K. Reaction of the inhibitor with methyl radicals provides for the relatively small amounts of CH3Br observed, but CH3 + Br2 - CHs Br + Br must also occur. The HBr formed reacts rapidly with H atoms to form H2 and Br, but the reaction is soon "balanced" in the flame as may be demonstrated by calculation of the equilibrium constant at various temperatures. The fluoro-carbon fragment produced in reaction (7) also reacts rapidly, in part with methyl radicals to give the observed elimination product CH2CF2 Later in the flame, above -1,400' K, F2CO is formed from the reaction CH2CF2 + 0 P F2CO + CH2 and k., -1.5 X 1013 at 1,600° K. The rather slow decay of carbonyl fluoride is attributed to reaction with H atoms according to the sequence F2CO I H - HF + FCO and FCO + H HF + CO.]

Jan 1, 1975

By Lloyd A. Morley

A guide to the development and use of an APL computer program for the analysis of load-flow problems is presented. The program is designed to provide an interactive method of load-flow study to improve underground coal mine electrical system design and safety. The theoretical basis for load-flow analysis is discussed, along with per-unit calculations which facilitate computation. Specific input/output, execution and network modification procedures are presented for using the APL program. In addition, typical results are given for examples taken from power system analysis literature.

Jan 1, 1977

By D. J. Bauer

Liquid-liquid extraction techniques were investigated by the Federal Bureau of Mines for the fractionation of rare-earth solutions. Separatory funnel work using tri-n-butyl phosphate (TBP) for extracting ceric nitrate from solutions containing sulfate ion resulted in almost complete extraction. Similar tests using primary amines for splitting trivalent rare-earth pairs and fractions gave promising results. The ceric nitrate extraction procedure was scaled-up by use of pressure-bubbler equipment, a series of spray towers for extraction, washing, and stripping. In this case only 84 percent ceric nitrate extraction efficiency was achieved. This work was done using dilute sulfuric acid for stripping.

Jan 1, 1960

By A. W. Effinger

The Bureau of Mines used regression analysis and applied statistical methods in an effort to rationalize the results of an experiment examining the effects of certain variables on carbon deposition in a reservoir for thermal recovery of petroleum. Although none of the 15 trials of the original experiment resulted in the response of weight-percent of carbon regarded by the experimenter as adequate, values calculated using canonical analysis in two trials yielded responses 33 and 54 percent higher than the minimum acceptable figure. The actual responses differed by less than 3 and 6 percent, respectively, from the predicted responses. Methods are described for defining a path of increasing response based on the minimum point and the response surfaces and for defining a set of values for the parameters in question, which result in increased response, A detailed explanation of the mathematical process used in this analysis is presented in the appendix for ease in computer programing the technique.

Jan 1, 1970

By C. D. Litton

The results of full-scale fire tests are used to determine optimum distributions of fire sensors for the protection of conveyor belt haulageways in underground coal mines. Empirical relationships are derived that relate the spacing of fire sensors to the rate of development of the fire hazard. For this application, a critical fire size is defined as that size of fire for which belt ignition and subsequent flame spread down the belt is assured. Detection and alarm, regardless of sensor type or sensing methodology, must be achieved at some point in time before the critical fire size is reached. Based upon this approach, it is found that the horizontal spacing for products-of-combustion sensors is in the range of 300 to 600 meters, while the required thermal sensor spacing is found to be ~4 meters or less. Additional design criteria are discussed for product-of-combustion fire sensing systems.

Jan 1, 1982

By John H. Scott

At the request of the Mine Safety and Health Administration, U.S. Department of Labor, the Bureau of Mines evaluated the model BT 300 C-D blasting machine tester, manufactured and distributed by Research Energy of Ohio, Inc. (REO), to determine whether the tester performed as stated by the manufacturer and responded satisfactorily to electrical faults introduced into the blasting machine circuit. Tester readings were recorded for 13 blasting machines and for 12 circuits constructed to simulate the electrical parameters of actual machines. The tester readings were acceptable for all of the blasting machines, although the switch position assigned to one machine produced an off-scale reading. The tester responded satisfactorily to the simulated circuits and detected serious voltage or capacitance faults when they were introduced. However, it did not respond accurately to certain resistance faults. Temperature tests were also made, and the tester performed equally well at temperatures of 20°, 42°, and 81° F. This tester was judged a useful accessory for field checking blasting machines for defective batteries and capacitors, despite its limitations. It is recommended that the tester manufacturer specify the lowest acceptable reading at which a blasting machine may be used and below which the blasting machine should be returned to the laboratory or manufacturer for maintenance.

Jan 1, 1981

By R. V. Ramani, P. M. T. White, D. Sutton

Appendix I. Part 1: Description Of Geology & Reserves System Introduction The Ore Evaluation and Reserve programs have been developed to aid in the evaluation of coal deposits, both qualitatively and quantitatively. The "Weighted Moving Average" technique used provides considerable flexibility in dealing with diverse parameters with differing distribution characteristics. Determination of Model Constants "a" and "k" - Unit 1 The flexibility of the method in dealing with diverse value parameter distributions lies in its ability to cater to the individual characteristics of each. These characteristics are embodied in the values determined for constants "a" and "k", namely, local and regional variations in value distributions, respectively. The empirical method used attempts to optimize the "a" - "k" combination. Realistic values for "a" and "k" are entered into the program together with sample values for the required parameters and their respective coordinate location values. All the values within a specified radius from the point being evaluated are used to interpolate a value at that point. (Note, the interpolated point is the location of one of the boreholes, values of which are not used in the calcula¬tion.) 3n a similar manner, interpolated values are calculated for each borehole location and for each parameter. This is done for each possible combination of "a" and "k".

Jan 1, 1974

By Richard J. Mainiero, Harry C. Verakis

The Bureau of Mines has conducted research to determine whether the total elapsed delay time for blasting bituminous coal in underground mines could be safely expanded beyond the present 500-ms limitation without igniting a methane or methane-coal dust atmosphere. The results indicated that the increase of total delay from 500 to 1,000 ms had no detectable effect on safety relative to incendivity as long as permissible practices were observed in all other aspects. Research was also conducted to evaluate the safety of 18-in hole spacing for delay blasting in coal relative to misfires. For a variety of permissible explosives, misfires were observed for about 50 pct of the holes at 18-in spacing. Based on this observation, the Bureau has recommended that the new regulations prohibit hole spacings of less than 24 inches in underground coal mines. Misfires were also observed for 24-in spacing, but the number of misfires and test shots was too small to sup- port any firm conclusions.

By R. V. Ramani, A. S. C. Owili-eger

? THIS PROGRAM SIMULATES METHANE FLOWRATES THROUGH THE GOAL ? SEAM BY THE GAUSS-SEIDEL ITERATIVE TECHNIQUE. THE MODEL IS A TWO ? DIMENSIONAL SYSTEM. THE ITERATIVE FORM OF THE GAUSS-SEIDEL IS ? OBTAINED FROM A PARTIAL DIFFERENTIAL EQUATION OF FLOW BY CENTRAL ? FINITE-DIFFERENCING APPROXIMATION SCHEME ? NPRESS IS THE NUMBER OF SPECIFIED PRESSURES EXCLUDING ? RESERVOIR AND FACE PRESSURES ? NQUAN IS THE NUMBER OF SPECIFIED FLOW QUANTITY.... EXCEPT FLOW ? OUT OF THE FACE. THIS- QUANTITY CAN BE POSITIVE(INJECTION) OR ? NEGATIVE ( PRODUCTION) ? XPERM(I,J) I S THE DIRECTIONAL PERMEABILITY IN THE X-DIRECTION AT THE POINT (I,J) ? YPERM(I,J) IS THE DIRECTIONAL PERMEABILITY IN THE Y-DIRECTION ? AT THE POINT (I,J) ? RESEP' IS THE RESERVOIR PRESSURE ? FACEP IS THE FACE PRESSURE. THIS PRESSURE IS ASSUMED TO BE ? APPROXIMATELY ATMOSPHERIC ? LENGTH, WIDTH, AND THICK ARE THE ZONE OR MEDIUM DIMENSIONS * PUHL I S A DUMMY NAME FOR VISCOSITY ? DMAXI IS VARIABLE NAME FOR INITIAL MAXIMUM ERROR OF ITERATION ? DMAXF IS A VARIABLE NAME FOR FINAL MAXIMUM ERROR OF ITERATION ? NITER IS A VARIABLE NAME FOR STORAGE OF NUMBER OF ITERATIONS ? RAD IS A VARIABLE NAME FOR THE SPECTRAL RADIUS OF THE GAUSS¬ ? SEIDEL MATRI-X. THIS PARAMETER ALSO MEASURES THE RATE OF ? CONVERGENCE OF THE ITERATION ? KOUNT IS AN ITERATION COUNTER ? MAXIT IS THE MAXIMUM NUMBER OF ITERATION SPECIFIED BY THE USER # EPS IS THE MAXIMUM RESIDUAL ALLOWABLE ERROR-FOR CONVERGENCE

Jan 1, 1974

Provide a low-cost, low-maintenance method for im¬proving mine water quality on abandoned mine land (AML) sites. Approach A model (figure 1) is presented for selecting, designing, and sizing one or several passive mine drainage treatment systems that can be used in remediation of AML. The three principal types of passive mine drainage technologies for the treatment of coal mine drainage are an aerobic system, a compost wetland, and an anoxic limestone drain. The multistep approach presented here provides a simplified method to characterize the type and magnitude of the water quality problem and then to select either a single treatment system or a combination of treatment systems to address the specific site situation. How It Works Step 1. Discharge Characterization. Characterization of the discharge consists of measuring the discharge flow rate and collecting water samples at the point of discharge for chemical analysis. Both the flow rate and chemistry of a discharge can vary seasonally and in response to storm events. It is important to account for this variability by determining flow rates and water chemistry under various conditions. Water should be analyzed for pH, dissolved iron (Fe), alkalinity, and hot acidity (using the H2O2 method).

Jan 1, 1994

By W. W. Adams

Reports received by the Bureau of Mines, Department of Commerce, from State mine inspectors, for November, 1930, showed that 219 men were killed in the coal mines of the United States during the month, an increase of 25 over the previous month and 33 over November, 1929. On the other hand the production of coal decreased, the output of 43,329,000 tons in November being 8,397,000 tons less than in October and 9,005,000 tons less than in November a year ago. The larger number of fatalities accompanied by a smaller output of coal resulted in a higher death rate4 per million tons in November than in the same month last year or in October, 1930. The November rate was 5.05, as compared with 3.55 for November, 1929 and 3.75 for October, 1930. The increase in the rate for the industry as a whole was chargeable entirely to bituminous mines,, as the anthracite mines had fewer fatalities in November than in either of the previous months to which reference has been made. Reports for bituminous mines alone 'allowed that accidents at class of mines resulted in a death rate of 5.12, based on 195 fatalities and a production of 38,122,000 tons. This rate indicated an increase of 55 per cent over the rate for October, of the same year, and 72 per cent over the rate for November, 1929. The October record was 146 fatalities and 44,150,000 tons, and that for November a year ago was 138 deaths and a production of 46,514,000 tons. Twenty-four deaths occurred at anthracite mines in November, 1970: the output of coal was 5,207,000 tons, hence the rate was 4.61 per million tons. During the corresponding month a year ago there were 48 deaths and 5,820,000 tons of coal produced, which indicated a death rate of 8.25. In October, 1930, the death rate was o.34; based on 48 deaths and 7,576,000 tons.

Jan 1, 1930

By Harold W. Lipper

A NEW record was set for helium shipment in 1962 for the 13th successive year. For the first time since 1949, the production of helium from natural gas at Bureau of Mines plants was less than in the previous year. The Bureau shipped 599.5 million cubic feet, 9 percent more than the 1961 volume, and produced 680.9 million cubic feet-a decrease of 6 percent from the record set in 1961. The Bureau added 77.2 million cubic feet to the volume stored for future use. Of the total 524.6 million cubic feet in storage, 522.4 million cubic feet is accumulated excess production from Bureau of Mines plants. The remaining 2.2 million cubic feet was purchased during 1962 from industry under the helium conservation program. The first two of five private plants began production in December to recover helium for conservation storage and ultimate use. A 425-mile pipeline system to transport helium from the five private plants to the Cliffside field was constructed by the Bureau at a cost of about $8 million.

Jan 1, 1963

Mining machine cabs were built to comfortably fit 90 percent of adult American males, and have controls that allow fast natural reactions during emergencies. These cabs and controls also fit 40 percent of the adult female population in the United States. The operators are also positioned for good visibility and for protection from roofing and ribbing hazards. Two basic designs were developed, one for seam heights on the order of 4 feet I and the second for seam heights near 8 feet. The sitting position of the largest person within the sample size group (termed a "95th percentile man") determined the basic cab shapes. The size of different parts of the human body and how they work together I established other design features of the cab. Areas of visibility, limits of operator movement, comfortable seating angles, etc., were carefully identified for the largest and the smallest persons within the sample size group. Placement of controls was based on these findings. The controls are designed and placed to allow operation with minimum physical strain and fatigue. See chart on other side of sheet.

Jan 1, 1978