Search Documents

The Technology Transfer Seminar on Mine Communications held on March 21-22, 1973, at the Pittsburgh Mining and Safety Research Center, Bruceton, Pa., presented information about recently developed equipment, instruments, and techniques for use in mine communications systems. All of the basic ideas presented in the fine seminar are operational in the Bureau of Mines Safety Research Mine in Bruceton.

Jan 1, 1974

By Lloyd A. Morley, Robert Stefanko

Before going directly to the analysis, it would be good to summar¬ize explosion-proof container approval methods. Both Magison (52) and Short (84) state that in general practice, the systems are certified for: 1. a rugged enclosure able to withstand an internal explosion but not allow explosively hot gases to escape, and 2. maximum surface temperature, with equipment operating inside, that will not ignite the surrounding atmosphere. Also, testing insures that any material in contact with the container surface will not be ignited by a hot spot. Associated with the first practice, the enclosures are inspected for: 1. a safe flange gap width, 2. a pressure increase during ignition, and 3. an hydrostatic pressure withstand level. The hydrostatic pressure level is almost always determined by a meas¬ured ignition-pressure test and is usually applied to prove the mechan¬ical design to some safety factor. Consequently, explosion-proof enclosure testing includes temper¬ature, permissible flame gap, and pressure. Specifications and prev¬ious research also can be similarly separated even though some interre¬lation exists between the flame gap size and internal enclosure pressure during an explosion. The Schedule 2G Sections applicable to these subjects are: 1. 18.2 Definitions; 2. 18.6 Applications;

Jan 1, 1974

By Lloyd A. Morley

Research performed on computer modeling of mine power systems under USBM Grant G0155003 1S described. The work was performed at the Pennsylvania State University from 5 November 1975 through 4 November 1976. Results presented are interim in nature, and future research is planned to integrate the simulations which have been developed. The thrust of this research has been divided into three main areas. 1. Modification of a previously developed model (Mine Power System Simulation or MPSS) to include interactive operation and the use of default (average) load data. 2. Development of a dynamic simulation of interdependent mine power system induction motors. 3. Development of an approach to modeling of motor shaft loading of induction machines for mining operations. During the course of the current year's research, significant results have been achieved in all areas. Construction of an interactive MPSS model has been completed and checked. This simulation was written in APL code and is fully interactive. In addition, default data representing 158 different pieces of mining equipment has been developed for use with the interactive model. Additional work described includes the construction of a dynamic simulation of interdependent continuous miner induction motors and the development of an approach fo: motor shaft load torque computation from experimental data.

Jan 1, 1976

By Otto Robert Stein

Erodibility of reclaimed surface mine soils is a subject in need of quantification. Effects of soil erosion from reclaimed areas may damage surrounding areas and the quality of water in nearby streams and lakes. It may also reduce the potential productivity of the reclaimed site. A study was conducted to determine erodibilities of different reclamation treatments and a nearby unmined soil at three Indiana strip mine sites. A rainfall simulator was used to artifically erode plots con¬structed within seven treatment categories and the unmined soil. Soil erodibility was assessed in terms of the Universal Soil Loss Equation (USLE) K factor. Values for K calculated from field data were compared to values predicted from independently measured soil properties. Differences in soil erodibility between treatments were site specific. Unmined soil had the highest calculated erodibility at one site but at two other sites soils having reclaimed A horizons were highest. Shaley overburden treatments had the lowest calculated erodi¬bility. Predicted soil erodibility was usually lower than that calcu¬lated from field data. Site specific slope gradient factors (S) were developed for reclaimed A horizon treabnents. This was done because the USLE S factor overestimated the measured soil loss at steeper slopes.

Jan 1, 1983

By K. P. V. Lei

The Bureau of Mines as part of its research effort to minimize the generation of hydrometallurgical waste, investigated a sodium sulfide leaching-electrolysis procedure for treating hydrometallurgical residues for elemental sulfur and base-metals recovery. Research was conducted on a leaching residue from a lead concentrate. The following procedure was developed. 1. The elemental sulfur was dissolved as polysulfide with an Na2S solution. 2. The resultant metal sulfide bearing residue was oxidatively acid leached in a cationic membrane electrolysis cell; the metals were solu¬bilized at the anode, and a base was generated at the cathode. 3. The elemental sulfur was recovered from the polysulfide solution by neutralizing with the acid in the anolyte. Byproducts of the neutralization were H2S and a sodium salt solution. 4. Sodium sulfide was regenerated by reacting the H2S byproduct with the base in the catholyte. 5. Lead as PbCL2 was recovered from the anode residue by brine leaching, and the other metals were recovered from the sodium salt solution as metal sulfides. 6. The barren filtrate from the metal sulfide precipitation constituted the recycled electrolyte. Ninety-eight percent of the elemental sulfur, 98 pct of the lead, and up to 80 pct of other accessory metals were recovered from a residue obtained from the FeCl3-NaCl leaching of a lead concentrate.

Jan 1, 1982

By Earl C. Lane

This is the second of a series of reports on a survey of petroleum products manufactured on the Pacific Coast from California crude oils. California crudes differ in many characteristics from the petroleum produced in other parts of the United States, and the claim has been made that some of the present federal Specifications for petroleum products tend to discriminate against California products. The purposes of the present survey are to determine what particular specification requirements California petroleum products characteristically fail to meet, how widely the products deviate from these requirements, and if possible to show whether the fault lies with the specifications or the products, or along what 'lines investigation to determine the question should proceed. The first report* of the series gave the physical and chemical properties of gasoline and mineral spirits made from California crudes. The present report deals with lubricating oils. Sixty-one samples of lubricating stocks and finished commercial products were generously donated by four of the large refining companies of California. Fifteen samples of automobile lubricating oils, made in California from California crudes, were purchased in the open market. Nine samples of lubricating oils mode from Gulf Coast crude were contributed for comparison by a company in Texas. The refining companies have continued the helpful and cordial cooperation shown by them in connection with the earlier work of the survey.

Jan 1, 1923

By Wilbert J. Huff

For the past 8 years the technical studies conducted by. the Explo- sives Division of this Bureau have been summarized in a series of annual reports.3 This report deals with activities from July 1, 1942, to June 30; 1943. Specific problems have been in immediate charge of section or unit leaders, to whom credit is given.

Feb 1, 1944

By Alexander May

In this Bureau of Mines publication stability constants for complexes of diethylenetriamine, 2-aminoethyl sulfide, triethylenetetramine, and 1,8-diamino-3,6-dithiaoctane with copper, nickel, zinc, and cadmium were deter-mined. The amine complexes were found to be much more stable than the analogous thio complexes. The results are interpreted in terms of possible molecular structure of the complexes.

Jan 1, 1974

By M. L. Skow, Maurice Deul, M. G. Zabetakis

This Bureau of Mines report presents a brief summary of the explosion trends in United States coal mines for the past 160 years. These trends show that in spite of the overall improvements in mine safety, the number of fatalities from ignitions of methane has actually increased in recent years. Suggestions are made of procedures that can be utilized to reverse this trend.

Jan 1, 1972

By Robert B. Schluter

The Bureau of Mines investigated separating copper-nickel mattes to recover a copper-rich fraction suitable for processing by conventional copper metallurgical processes and a nickel-rich fraction suitable for processing in a hydrometallurgical nickel circuit. Distribution of cobalt and precious metals between the copper and nickel fractions was also determined. A matte containing a nominal 65 pct Cu, 9 pct Ni, 4 pct Fe, and 20 pct S was separated into a copper fraction that comprised 80 pct of the matte weight and contained 70 pct Cu and <1.5 pct Ni, plus a nickel fraction that contained 40 pct Ni and 30 pct Cu. Recoveries of copper and nickel into their respective fractions were 90 pct and 87 pct. These results were obtained in a laboratory flotation cell at a matte grind of 90 pct minus 500 mesh and a pH of 12.4, using 1.7 pounds DPG (diphenylguanidine) per ton of matte as collector and frother. Magnetic separation was used to remove metallic iron-nickel alloy from the copper fractions. Distribution of cobalt was about 70 pct to the nickel fraction and 30 pct to the copper fraction. Silver reported predominately to the copper fraction, while Au, Pt, and Pd were essentially entirely recovered in the nickel fraction.

Jan 1, 1982

By Thomas V. Falkie, R. Venkataramani

1. Summary This investigation is concerned with description of the loading function at the underground coal face, and the identification of varia¬bles - geological, geometric, mechanical, and operational - that affect the loading function. The immediate objective of this work was to provide information for operations-research studies as applied to underground coal mining, and the broad objective was to provide guide¬lines for planning and equipment selection in underground coal mining. The loading function was expressed as -a statistically-developed linear mathematical model. Originally, fifteen independent variables were considered which potentially could have influenced the loading function. These variables were constructed on the basis of measurable or estima¬ble geometric and geological properties at the working face, mechanical characteristics of the mining machine, and certain operational proce¬dures of mining. The original model explained 64.0 percent of the experimental variation. The final condensed model explained 54.1 percent of the experimental variation in terms of only five indepen¬dent variables, namely: 1. Ratio: width of cut/total width of cutter 2. Ratio: height of cut/diameter of cutter 3. Total horsepower of cutter-drive motors 4. Rotation speed (RPM) of cutter 5,. A subjective estimate of machine quality and operator skill Certain limitations were found to exist in the evaluation of the variables. Principle among these limitations was the impossibility of precise measurement of tonnage loaded in certain instances.

Jan 1, 1972

By Ruth A. Holmes

A Bureau of Mines method for recovering nickel, cobalt, and copper from low-grade domestic laterites is described, which includes the unit operations of solvent extraction and electrowinning. Previous Bureau work indicated that addition of Na2S04 (sodium sulfate) to the nickel electrolyte improved current efficiency in nickel electrowinning. The present study determines the compatibility of Na2S04 with nickel strip-ping in the solvent extraction operation of the Bureau method. The effect of adding 100 g/l Na2S04 on nickel stripping, phase disengagement, and pH was determined in comparative laboratory-scale tests. In continuous-circuit testing, Na2S04 reduced stripping efficiency to the extent that five, instead of four, strip stages were required for complete stripping of nickel from the loaded solvent. In tests made in a phase-disengagement cell that had a variable settler area, the addition of Na2S04 did not significantly affect phase separation characteristics. The pH of the nickel electrolyte in the temperature range of 20° to 65° C was also unaffected by the addition of Na2S04. An economic evaluation showed that the energy saved by adding Na2S04 to the electrolyte would more than offset the cost of adding another stripping stage.

Jan 1, 1983

By G. V. Sullivan

This report describes an investigation by the Bureau of Mines of flotation techniques for the recovery of chromite from fine-grained disseminated ores. Reported work on the concentration of chromiferous materials shows that flotation has been applied almost exclusively to slime-free pulps. Therefore, chromium recoveries that could be obtained by flotation were related to the amount of slime rejected. However, results of recent studies by the Bureau of Mines showed that des liming is not a requisite to selective concentration of chromite. Laboratory-scale tests on seven ore types from the more important chromium-bearing areas of the Pacific Northwest showed flotation to be technically feasible for treatment of all but one of the samples. Concentrate grades were affected more by the composition of the chromite mineral than by the grade or character of the ore. Test results from three of the samples showed that, without prior desliming of the pulp, 78 to 91 percent of the chromium could be recovered in concentrates of 90 percent or more chromite; two samples responded to similar treatment, resulting in concentrates of more than 80 percent chromite with recoveries of 85 and 89 percent chromium. One sample of mill products, subjected to severe weathering, required removal of the primary slime to obtain a concentrate of 65 percent chromite with only 75 percent chromium recovery.

Jan 1, 1960

By N. C. Tomoeda, W. D. Bensema, J. W. Adams

Measurements of surface magnetic field noise were made at various locations over the Geneva Coal Mine near Price, Utah, on June 12, 1973. The locations selected were on the surface over emergency locator beacons underground at depths between 350 meters (1150 ft .) and 488 meters (1600 ft .) . The surface terrain where these measurements were made was mountainous, and access was difficult. There were no power lines within several miles, and the weather was clear; therefore, the magnetic noise levels were about as low as will normally occur. Results of measurements of distant sferics indicate rather sharp cutoff frequencies below which broad- band, impulsive noise is attenuated. The mechanism of propagation for this noise above the daytime cutoff frequency of 3500 Hz and the nighttime cutoff frequency of 1700 Hz is deduced to be a waveguide formed by the D or E layers of ionosphere as an upper plane and the earth as a lower plane. The measurement systems used are similar to those used earlier. The technique is to record broadband, analog signals, digitize the data, and use a fast- Fourier transform to obtain spectral plots. This tech- nique is novel in that it can measure simultaneously all magnetic field energy within a limited portion of the spectrum for a limited time, and, after processing, reproduce the events occurring in that time interval in great detail .

Jan 6, 1974

By Stephen C. Tadolini, Thomas M. Barczak, Paul McKelvey

A new generation of hydraulic mine support prestressing devices has been developed. These thin-walled steel shells are machine-welded and can be inflated with water or any liquid to provide prestressing for a wide variety of roof support products ranging from Can supports to props and cable bolts. With an expansion capability of several inches, depending on the geometry and size of the unit, they can also establish roof contact eliminating the need for wooden wedges or crib blocks that are commonly employed with several standing roof support products. Capable of withstanding pressures from 1,000 to 6,000 psi, these cells are able to transfer roof loading into the support structure without rupturing. A recent development has been the addition of an inexpensive yield valve that provides control of the maximum pressure and load development on the support. This paper examines the performance capabilities of these inflatable prestressing units and the impact they have on the performance of various support systems, including an evaluation of the overall stiffness of the support system and the load control during yielding of the prestressing unit. Recommendations are made regarding the design requirements of the prestressing unit to optimize the support performance. A summary of mine applications using this technology is provided with general comments regarding their impact on ground control.

By Yagesh N. Bhambhani, Rammohan V. Maikala

Landstrom et al. (1985) suggested the possibility of cortical activation during exposure to WBV, however, it is not known how cerebral physiology (oxygenation and blood volume) responds in healthy women during different vibration frequencies. This study examined the role of backrest support and handgrip work on cerebral oxygenation and blood volume responses, during exposure to seated WBV. Methods Fourteen women (age: 23.9 ± 3.5 years) were randomly exposed to three frequencies of WBV (3, 4.5 and 6 Hz at approximately 0.9gr.m.s in the vertical direction) on a customized vibrating base (Advanced Therapy Products, Inc., USA) in a seated posture on three separate days. On the first day, the subjects completed an aerobic fitness test until volitional exhaustion on an arm cranking ergometer (Cybex, MET 300, USA). Each WBV session lasted 30 min (6 min baseline without WBV, 8 min WBV ‘with’ or ‘without’ backrest support, and 4 min recovery from WBV, 8 min WBV with ‘opposite’ backrest condition, and 4 min recovery following WBV). During 8 min WBV exposure ‘with’ and ‘without’ backrest support, subjects performed maximal voluntary rhythmic handgrip contractions with their right hand for 1 min using a dynamometer. To obtain regional oxygenation and blood volume responses, a NIRS sensor (MicroRunman, NIM, Inc., PA, USA) was placed on the anterior right frontal lobe just below the hair and close to fronto-temporalis region (Maikala et al. 2005). Results Baseline oxygenation and blood volume values were recorded during recovery from each WBV session of ‘with’ and ‘without’ backrest support. The physiological change in oxygenation and blood volume during each frequency (3, 4.5, and 6 Hz) for both backrest (‘with’ and ‘without’ a backrest) and workload (WBV only and WBV combined with rhythmic handgrip contractions) was calculated as the difference between the maximum values identified for each WBV condition of backrest and workload and baseline values (Maikala et al. 2005). Three-way analysis of covariance with repeated measures (frequency, backrest, and workload) with a fully crossed design was used to evaluate the differences in the oxygenation and blood volume responses (measured in optical density [od] units). Peak oxygen uptake during

Jan 6, 2006

By E. V. Cilento, K. A. DiGregorlo, R. C. Lantz

A kinetic model was developed to describe the production of superoxide (02) by single pulmonary alveolar macrophages (PAM). Model predictions were compared to experimental results obtained from single rat PAM. The O2 - was quantified by measuring the reduction of nitroblue tetrazolium (NBT) to a diformazan precipitate (NBTH2) from video-recorded images of individual cells. The kinetic model considered three reactions: (1) the production of extracellular 0 - from the reduction of oxygen by NADPH oxidase using intracellular NADPH as the substrate, (2) the subsequent dismutation of o2- to from O2 , and (3) the reaction of o2- and NBT. NBT specificity for o2- was analyzed by comparing results in the presence and absence of superoxide dismutase (SOD) which catalyzes the dismutation of o2- to H2o2. Measured PAM heterogeneity was accounted for by varying the concentration of intracellular NADPH, its rate of depletion, and the concentration of intracellular NADPH oxidase in the kinetic model. Model predictions compared favorably with experimental results except when SOD was present. This discrepancy may be due to diffusional limitations since NBT is a relatively small molecule (818 MW) compared to SOD (34000 MW). In addition, the cell surface is both ruffled and negatively charged, which may introduce steric hindrances and/or electrostatic effects since SOD is also negatively charged.

Jan 1, 1988

Develop a method for control of groundwater inflow to chronically "wet" sections of underground coal mines, in order to reduce groundwater interference with mining activity and to minimize acid mine drainage. Approach In eastern coal regions, groundwater stored in fracture zones in the rock mass can create a significant water problem for underground mining operations. Fracture stored inflow to mine workings impedes mine productivity since storage water sources usually release at the active face, creating the poor mining conditions typical of a "wet" section. Fracture water can also contribute to AMD problems when the water subsequently contacts sulfide minerals in the coal, The Bureau of Mines has developed a mine-dewatering method that eliminates many of the problems associated with mine water inflow by draining these fracture zones before the water can reach the developing face and interfere with mining activity. How it Works The dewatering method removes large volumes of the stored groundwater through high-capacity pumping from a minimal number of wells placed strategically on fracture traces (the surface expressions of fractured rock zones). These fracture traces are located through low-level aerial photographic and geologic investigation. As shown on the map, dewatering wells are sited precisely on fracture trace intersections in order to take advantage of the increased pumping capacity gained from these zones of high permeability. Once well drawdown indicates that the stored water is depleted,

Jan 1, 1983

By Bill M. Stewart, Phil W. Patton, Curtis C. Clark

Back injuries from handling materials in underground mines continue to be a major safety problem. In spite of the ingenuity of many people and the development of numerous mechanized aids, the number of materials-handling injuries remains second only to the number of roof fall injuries in underground coalmines. Relocation and repositioning of electrical cable, conveyor belt parts, and roof bolt sup-plies in particular are the sources of significant numbers of back injuries. To help reduce such injuries, researchers at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health are examining Mine Safety and Health Administration accident data to determine correlations between materials-handling tasks and the number of back injuries. Also being investigated are new technologies used in underground mines in the United States. Equipment is being developed or modified that would replace the necessity of doing lifting tasks manually. A Coleman manipulator was tested, and modifications were made to make it more suitable for underground mine use. To reduce or eliminate the need to manually clean off materials that commonly plug grizzly openings, a track-guided pincher arm device was developed. Oversized rock can be broken with the pincher arms in the up position, and the arms can be lowered to grab and remove debris. The arm can also be used in a sweeping action to remove cohesive fines that may bridge grizzly openings.

By Mark L. Chatman

This report presents an economic mineral assessment and Inventory of mines and prospects In the approximately 176,000-acre Patagonia Mountains-Canelo Hills Unit of Coronado National Forest. Deposits or areas most likely to experience future development are characterized in terms of their economics, based on data acquired by the author from a variety of sources, and supplemented by USBM field data collected by other workers in 1990 and 1991. Numerous mine maps, rock-chip sample assays, and detailed descriptions of mine and prospect sites are in this report and appendixes. Heavy but sporadic mining, mainly between the 1850&apos;s and 1950&apos;s was nearly all confined to the Patagonia Mountains. High-grade sulfide veins, replacements, and skarn deposits accounted for most of the production, which included large quantities of zinc, lead, copper, and silver, and considerable quantities of gold. Small Quantities of molybdenum, manganese, tungsten, and placer gold have been mined. Most of the traditionally mined metalliferous sites will not see future activity due to the low tonnages present and removal of most high-grade rock. Possible future development areas include copper porphyries and breccia pipes; most are too deeply buried for current development. Localities where similar deposits may be concealed are identified.

Jan 1, 1994