Search Documents

By Errol D. Sehnke

This U.S. Bureau of Mines report provides detailed information on worldwide bauxite production capacity by mine and country, including bauxite substitute materials in countries of the former Soviet Union, The information was compiled from a variety of domestic and international sources and was based on information available to the Bureau through December 31, 1994. Capacity data represent announced installed and planned capacities and do not necessarily reflect a U.S. Bureau of Mines judgment of actual mine operating levels or timing of planned expansions. The year-end capacity is the ?in place? capacity or estimated production capacity, whichever is larger.

Jan 1, 1994

By Soule&apos, John H.

Although known since 1902, the Capitan iron deposits have not been tined, mainly because of the low grade of the ore. Only a small amount of exploratory work has been done since the discovery. C. H. Johnson, district engineer of the Bureau of Mines in New Mexico in 1942-4, visited the property; as a result, preliminary sampling of the property was done in 1943.2/ Owing to the results of this preliminary work, an extensive development program by wagon drilling was planned and executed early in 1944. Equipment available at that time was limited in the depths that could be reached; and as geologic studies indicated the possibility that other limestone beds below the surface might have been replaced by iron minerals, a supplementary development program by churn drilling to reach greater depths was prosecuted in late 1947 and early 1948, with the author as project engineer.

Jan 1, 1949

By R. E. Lindstrom

Separation efficiency of a 4 percent divinylbenzene (DVB) resin is not altered over a wide range in temperature. A 12 percent DVB resin, however, exhibits a marked sensitivity to temperature. When flow rates are high at ordinary temperatures, 4 percent DVB resin exhibits higher efficiency, but at 200° F. both resins are equal in performance. Effective separation of rare-earth mixtures may be obtained with hydrogen as a retaining ion by maintaining column temperatures above the solubility of ethylenediaminetetraacetic acid (EDTA) in the free acid form. Slightly lower separation characteristics were obtained with this method as compared with copper as a retaining ion, Recovery of 99 percent of the EDTA from spent eluting solutions that contain copper has been accomplished by a calcium-copper displacement reaction followed by EDTA precipitation. Impurities in the product are correspondingly low. Recoveries of EDTA from holmium solutions with sulfuric acid are substantial; however, those from yttrium solutions are quite modest. Radiotracer experiments show the presence of approximately 0.1 percent yttrium contamina¬tion in the recovered material. The study presented is one phase of a broad research program designed to assist the technology of separating and purifying rare-earth elements.

Jan 1, 1961

By Sean Gallagher

Humankind's interest in measurement of human physical strength probably dates to the first humans. At that time, life was truly a struggle in which the fittest survived. To a great extent, fittest meant strongest. Interestingly, current interest in human physical strength in the workplace stems from 1970-1980s vintage research demonstrating that persons with adequate physical strength are less likely to be injured on physically demanding jobs. Survival in many modem workplaces may still be a case of survival of the strongest. There is, however, a flip side to this issue - that persons with limited strength are more likely to be injured on "hard" jobs. To address this problem, we can apply what we know about physical strength to job design. "Hard" jobs can be redesigned to be within the physical strength capability of most people. Since physical strength is important to these jobs, we must find ways to quantify it through testing. This publication concerns human physical strength testing. Its purpose is not to recommend any particular type of testing, but rather to describe the types of testing available and their uses. It is up to each individual user of strength testing to decide which testing technique is most appropriate for his or her particular application. This booklet discusses four types of strength testing: isometric, isoinertial, psychophysical, and isokinetic.

Jan 1, 1998

Enhance coal mine worker safety and productivity by developing a means to control and predict coal mine mountain bumps. Approach The Bureau of Mines has been engaged in extensive research to understand coal mine mountain bumps and their effect on underground coal mining in the United States. Information was collected on the geologic conditions, mining techniques, and engineering parameters at five mountain-bump-prone mines. Although research has not yet evolved to the point where mountain bumps can be effectively predicted or controlled, such studies are invaluable for providing clues that can lead to the development of mountain bump mitigation technology. Case Study Results and Recommendations Mountain bumps in coal mines are explosions of the coalbed that violently release the strain energy stored within it into openings created by mining. Such an event is not only dangerous to mine workers, but can cause substantial amounts of damage to mine equipment, resulting in productivity loss and downtime. In a coal mine, the occurrence may cause coal to be expelled violently from the coal face or coal pillars or cause the mine floor to heave suddenly. Coal bumps are usually accompanied by a very loud noise and tremors or vibrations. Such ground failure:; usually occur in the vicinity of an active gob line in an active retreating room-and-pillar panel, or at or near the face in an advancing or retreating longwall mining panel.

Jan 1, 1989

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By N. E. Hanna

The current Bureau of Mines active list of permissible explosives includes 124 brands. Thirteen are gelatinous and the rest are the more commonly used granular ammonium nitrate type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1965

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By F. A. Penning

A number of highly instrumented free fall tests were performed on an arrestment system for a man cage in a vertical shaft. Tests were conducted in the U.S. Bureau of Mines free fall test tower at the Colorado School of Mines. A single tooth safety dog was used to stop on 4x6-in. Keruing (Phillipine mahogany) wet and dry wood guides. The safety dog had a penetration depth of 1 in., an adjustable width from 1-1/2 to 2-1/4 in., and a tooth angle of 80 deg. Twenty-seven free fall tests were performed covering a range in weights from 3-1/2 to 10-1/2 tons, hoisting velocities from 850 to 1350 feet per minute. Average g loads were measured from a low of 0.6 to a high of 3.4. The electronic instrumentation included piezoelectric and seismic mass accelerometers, strain gages on structural and mechanical elements, load cells in the guides, and distance measuring. Computer analysis was used to correlate with experimental measurements used to calculate stress. A statistical analysis gave no indication that the velocity or area affected the wood crushing stress. The instrumentation revealed a chatter occurring during the stop as shown by the accelerometers, strain gages, and load cells. Additional work is required to analyze this newly discovered phenomenon. The chatter imposes loads much higher than the average g load.

Jan 1, 1980

By T. J. Ballard

"The Hog Creek mine, in lot 92 of the 17th district in Towns County, Georgia, was examined in 1890 by F. P. King, who reported the existence there of a 4-foot vein of corundum. The mine is about 2 miles west of Hiawassee, on the southern side of Ramey Mountain. Ed Burch, of Hog Creek, holds the surface rights, and the mineral rights appear to be vested in the heirs of William R. McConnell, who formerly owned and prospected the property.Examination by the Bureau of Mines showed the workings to be caved, but it was thought advisable to open the mine and uncover the reported vein. The Bureau's work consisted, of trenching and cleaning out the pits and shaft.William R. McConnell, the former owner, prospected the property in about 1890. At some tine during that operation, the prospect was visited by Francis P. Kings a geologist with the Georgia Geological Survey.3/King reported that a 4-foot vein of corundum was exposed g feet below the surface in the main cut and was opened for 20 feet along the strike. He also reported that the so-called ""Georgia rubies"" were taken from this mine.The main mine is about 2,000 feet- north of Hoc Creek on a timbered southern slope of Ramey Mountain. It lies at an altitude of about 2,100 feet, approximately 100 feet above the high-water level of the Catuga reservoir, which floods Hog Creek to a quarter of a mile above its confluence with the Hiawassee River. The nearest water is a small branch about 1,000 feet to the west.Chlorite schist is the principal host rock. It has been intruded by irregular masses of a very herd periodtite rock possibly troctolite. The schist near the surface is extremely weathered, presenting white and red laminations parallel to the schistosity. At a depth of 40 feet in the cross-cut it appears as a fine-grained green-chlorite schist. The schist strikes about N. 350 E. and dips 800 to the southeast.No corundum vein was found, and if any existed it must have been mined out after King's visit. In the pit, about 15 feet west of the shaft, approximately 150 pounds of zoisite and an occasiona1 small crystal of corundum were found imbedded in schist about 18 feet below the surface, near hard, dense troctolite."

Mar 1, 1946

By Kenneth J. Miller

The Bureau of Mines two-stage coal-pyrite flotation process was modified to provide a more concentrated final clean coal slurry underflow which could be dewatered economically by filtration or centrifugation. This was accomplished by doing the first-stage coal flotation step in the conventional manner with a slurry of about 8 percent solids, but running the second-stage pyrite Flotation step with undiluted coal froth concentrate containing about 25 percent solids. The final clean coal underflow produced by the new technique contained between 26 and 30 percent solids; this pulp was sufficiently concentrated to be filtered industrially without further thickening. Sulfur removal was equal to that obtained using dilute second-stage pulp,

Jan 1, 1975

By John W. Taber

"INTRODUCTION AND SUMMARYDiscovery of these unusual fluorite deposits was brought to the attention of the Bureau of Mines late in 1951, shortly after the first locations were made. A brief investigation of the deposits by the Bureau revealed seven principal outcrops of fluorite in two areas. The smallest outcrop continuously exposes massive fluorite over an area 25 by 55 feet; the largest outcrop is a similar exposure 180 by 240 feet. The deposits, appear to be sharp-walled, low-angle, tabular ore bodies in granite and are at least 10 feet thick.The Bureau investigation of the deposits included bulldozer strip-trenching, drilling and blasting rock cuts, and channel sampling across three of the largest outcrops. This sampling indicated an average grade of 97.2 percent CaFp and 1.44 percent SiO2.Preliminary metallurgical tests on the ore indicate that it can be concentrated to acid-grade specifications by simple gravity methods. One laboratory test recovered 78.4 percent of the fluorite in a product containing 98.7 percent CaF2, 0.25 percent SiO2, and 0.10 percent Fe2O3."

Oct 1, 1952

Control surface stream loss by identifying and selectively sealing water loss zones in stream channels overlying underground mines. Approach Electromagnetic terrain conductivity surveys, coupled with stream gaging, are performed within a stream channel to identify saturated fracture zones associated with loss of stream water. This information is used to target locations for the injection of expandable polyurethane grout. The grout is injected two to three feet beneath the surface of the strcambed, across each loss zone, to seal the fractured strcambed and restore stream flow across the damaged area. How It Works Multiple zones of infiltration (natural and induced) normally exist in stream channels overlying mined areas, causing water handling and/or acid drainage problems in the mines as well as loss of stream flow. It is typically difficult to accurately locate these loss points. Therefore, Conventional methods of stream repair, such as using plastic membranes or clay and rock rip-rapping, are applied to long lengths of a stream channel. The two step approach developed by the Bureau of Mines First quickly and accurately locates loss zones using electromagnetic ground conductivity survey and gaging instruments. Conductivity is measured at fixed spacings (typically 25-50 ft depending on the instrument and desired observation depth), Ground conductivity increases when saturated conditions exist at depth. These apparent flow loss zones are confirmed by gaping, to eliminate possible effects due to unobservable metal debris adjacent to or buried in the stream sediment.

Jan 1, 1991

By P. A. Richardson

The current Bureau of Mines active list of permissible explosives includes 76 brands. Eleven are gelatinous and the rest are the granular type. The list of permissible blasting devices comprises five Cardox models.

Jan 1, 1970

By D. N. Nilsen

The Bureau of Mines is investigating a method to recover Ni, Cu, and Co from low-grade domestic laterites through reduction roasting, leaching, sol-vent extraction, and electrowinning unit operations. The objective of this research is to develop processing technology that can convert low-grade domestic deposits containing critical metals into national reserves. As a part of this research, a solvent extraction system was investigated for the extraction of nickel and copper, followed by the separation and production of suitable electrolytes. Nickel and copper were coextracted from ammoniacal ammonium sulfate leach liquors (pH~9.5) with LIX 64N extractant in a laboratory-size mixer-settler continuous circuit. Three extraction stages resulted in >99-pct extraction of nickel, substantial copper extraction, and essentially no cobalt extraction from leach liquors. A crowd stage reduced the ammonia loading on the solvent by maximizing nickel loading. Residual ammonia was removed from the loaded solvent with a pH-controlled scrub. Nickel and copper loaded on the solvent were separated by selective stripping. Typical nickel strip circuit operation using electrolyte containing 90 grams per liter (g/l) Ni and 11.9 g/l H2S04 yielded >99.9 pct Ni stripped from the solvent in five stages. The copper loading on the recycled solvent was controlled in a copper strip stage using electrolyte containing 25 g/l Cu and 160 g/l H2S04,

Jan 1, 1981

By H. K. Sacks

The Bureau of Mines has improved a mine dust incombustibles analyzer originally developed at the Bartlesville Energy Research Center (BERC). This analyzer provides quick, accurate analysis of the percentage of incombustible material present in dust samples taken from mine ribs, roof, and floor so that costly overdusting may be eliminated while still maintaining a proper level of incombustibles. The changes being effected on the present design of the BERC model IV rock dust analyzer should simplify its operation and calibration procedures, resulting in increased accuracy.

Jan 1, 1976

By T. M. Romslo

"INTRODUCTION This report presents factual data obtained by the Bureau of Mines in the course of an investigation of the Antler mine in the Cedar Valley mining district, Mohave County, Ariz.The Antler property was first examined by Thomas L. Chapman, mining engineer, Bureau of Mines, on December 18, 1943, and January 28, 1944. In June 1945, A. H. Wadsworth, Jr., and R. L. Griggs, geologists, Federal Geo¬logical Survey, examined the Antler mine and several other mines in the district. Both Chapman and Wadsworth recommended diamond drilling of the Antler property to determine the character and extent of ore deposition.In October 1946, the surface and underground workings were surveyed by George Huseman, Mining engineer, and T. M. Romslo, project engineer. The following month Eldred. D. Wilson, geologist of the Arizona Bureau of Mines, assisted by the project engineer, mapped the geology. Subsequently trails were built to drilling sites and diamond drilling started January 16, 1947. The project was completed April 25, 1947.ACKNOWLEDGMENTSIn its program of investigation of mineral deposits, the Bureau of Mines has as its primary objective the more effective utilization of our mineral resources to the end that they make the greatest possible contribution to national security and economy. It is the policy of the Bureau to publish the facts developed by each project as soon as practicable after its conclusion. The Mining Division, Lowell B. Moon, chief, conducts preliminary examinations, does the actual investigative work, and prepares the final report. The Metallurgical Division, O. C. Ralston, chief, analyzes samples and takes beneficiation tests."

Mar 1, 1948

By William H. King

The Nevada Massachusetts tungsten deposits (fig. 1) are in the Mill City Mining District in north-central Pershing County, Nev., about 37 miles southwest of Winnemucca. Contact metamorphism of thin limestone beds within a series of metamorphosed sedimentaries formed scheelite-bearing ore bodies. These deposits are distributed over a wide area. A Bureau of Mines development program was started January 11 d was completed on July 25, 1941. This work was centered on the outer and less explored beds in the district and comprised trenching, sampling, and diamond drilling. Exploratory work was done in cooperation with the U.S. Geological Survey. Project work substantially increased the reserve tonnage of marginal ore in three of the areas explored and proved the nonexistence of tungsten in a fourth area. The following pages summarize the history of the district, outline property ownership, and describe physical features and ore deposits. The plan and results of the work performed by the Bureau of Mines are presented along with geologic and topographic maps, assay maps, and diamond drill-hole logs.

Jan 1, 1950

By T. J. Ballard

The Union Copper mine is in the Gold Hill district; Rowan and Cabarrus Counties, N. C. The mine was discovered in 1799 and first worked as a gold mine; but copper was encountered at depth, and the property became an important producer of copper. It is estimated that the mine produced 5,000,000 pounds of copper before operations were discontinued in 1907. As part of the strategic minerals program, the Bureau of Mines conducted a development project on the property from July 1943 to November 1943. Eight diamond-drill holes totaling 2,500 linear feet were drilled to delineate the ore body. Analyses 205 core samples were made. Tabulations of sample analyses and drill-hole logs are presented in this report.

Jan 1, 1948

By Kenneth M. Earl

In its investigation of deposits of strategic minerals, the Bureau of Mines did some development drilling at the New Galena Deposit in an endeavor to find an additional source of supply of lead. In Bucks County, lead and zinc minerals have been found in shales over a largo area west and northwest of Doylestown. Considerable mining has been done in the vicinity of New Galena on the North Branch of Noshaminy Creek, 3 miles northwest of Doylestown. It has not been possible to obtain a satisfactory history of the New Galena mine, as there is much disagreement in statements. Most of the mining was done in open pits. Two shafts were sunk to shallow depth; one of these became part of the main pit' which is 256 foot long, 50 to 75 feet wide, and 20 to 44 feet deep. Small pits 8 to 10 foot square wore sunk on the ore zone, which extends some 1450 feet to the southwest. The rock containing the minerals is either black or gray shale. The gray material closely resembles limestone. The following minerals have been reported from the mine: quartz, ankerite, calcite, galena, sphalerite, pyrite, chalcopyrite, and bornite. Some of the galena has yielded 10 to 15 ounces of silver and 10 cents in gold per ton. The average grade of the ore as mined is not known. To investigate the downward extension of the ore shoot, the Bureau drilled two holes aggregating 373.9 feet, No additional ore was developed by this work.

Jan 1, 1950