Search Documents

By W. H. Young

THE DOMEST[C bituminous coal and lignite industry remained fairly steady in 1959 compared with 1958. Although mechanization continued to expand and production increased slightly, consumption, average value, exports, and employment decreased. The percentage of underground production mechanically loaded, the percentage of total production mined by stripping, and tonnage per man per day were at their highest levels. Production.-The output of bituminous coal and lignite in 1959-412 million tons-was 0.4 percent greater than the 410.4 million tons produced in 1958. Production was retarded in 1959, largely owing to the steel strike and reduced exports.

Jan 1, 1960

By Albert E. Schreck

[THE COMPOUNDS of strontium were confused with those of barium until 1790, when A. Crawford discovered that the mineral strontianite, long believed to be a barium mineral, was a compound of a new element. This discovery was confirmed 2 years later by I. C. Hope. The mineral was named strontianite because it was found near the town of Strontian in Argyllshire, Scotland. In 1808 Sir Humphrey Davy isolated strontium metal by the electrolysis of fused chlorides. Celestite (strontium sulfate) and strontianite (strontium carbonate) are the principal strontium minerals. Because of its more widespread occurrence, celestite is more important commercially.]

Jan 1, 1959

By Robert L. Mentch

CADMIUM is one of the metals apparently destined to remain relatively scarce. The en tire supply of primary cadmium is recovered as a byproduct, concurrently with the treatment of ores of other metals. Development of the cadmium industry is attributed to metallurgical improvements in the zinc industry; output depends almost wholly upon zinc production. Cadmium is a metal of specialized uses where its superior performance has developed a strong, expanding demand. The supply, however, has been relatively unresponsive to price because of its byproduct nature. Cadmium's outstanding properties would assure it a manyfold greater market if more were available at lower prices.

Jan 1, 1958

By J. L. Konchesky

The Bureau of Mines investigated the main reactions of coal gasification by steam. Coal (minus 70 mesh)-water slurry was fed into a laboratory-scale tube-coil gasifier to show the effects of residence time (0.6 to 1.1 sec), steam-coal ratio (2 to 11 lb/lb), and temperature (1,600° to 1,900° F), at about 1-1/2 atm. Devolatilization was very rapid: about 70 pet of the coal's volatile matter evolved within 0.6 sec at about 1,600° F; temperature increase released more volatile matter until about 95 pct was driven off at 1,900° F. Devolatilization was not increased by raising steam concentrations and was only slightly increased by extending residence time. Below 1,600° F, there was no evidence of the steam-carbon reaction, but at 1,900° F more than 80 pct of the coal's fixed carbon was converted to gas; the conversion was increased Significantly by increased residence time and steam concentration. The water-gas shift reaction occurred simultaneously with devolatilization, and the steam-carbon reaction, approaching equilibrium with increased residence time and temperature and decreased steam concentration.

Jan 1, 1969

By Thomas M. Barczak

The U.s. Bureau of Mines is conducting research to optimize the utilization and design of mine roof support systems. This report describes methods to evaluate resultant loading on longwall shields, defined as external resultant vertical and horizontal force acting on the canopy and base. Four models are considered: two rigid-body models, an elastic model, and a numerical model. The rigid-body models equate measured internal shield forces to unknown external resultant shield forces (loads) through rigid-body analysis of static equilibrium requirements. The elastic model develops a solution to shield mechanics by evaluation of the load-displacement relationship and stiffness characteristics of the support structure. The numerical model is a two-dimensional finite-element representation of a shield structure. Model determination of resultant shield loading is compared to controlled loading of a shield in the Bureau's mine roof simulator. Parameters investigated are shield height, canopy contact configuration, canopy and base horizontal constrainment, and boundary conditions imposed by vertical and horizontal shield displacements. It is concluded that rigid-body models are most applicable to in situ measurement of shield loading. Applications requirements and potential error sources are discussed.

Jan 1, 1990

By D. E. Wolfson

Destructive distillation (carbonization) was shown to be a feasible method of disposing of scrap tires. The Bureau of Mines conducted tests under a variety of conditions. Solid, liquid, and gaseous products were produced, recovered, and analyzed. The quantities of the various products were shown to be quite dependent on the test temperature. Variability in composition of the liquid and gaseous products with changes in test temperature was also significant.

Jan 1, 1969

"An active list of permissible explosives was published in September 1935 as part of United States Bureau of Mines Report of Investigations 32S6, under the title ""Active List of Permissible Explosives and. Blasting Devices Approved. Prior to July 31, 1935."" This list included 154 brand names,Changes in the list that have been authorized subsequently placed 24 addi¬tional brands of permissible explosives on the active permissible list as a re¬sult of tests, changes in brand names, or transfer from the inactive list. Eight permissible explosives were transferred from the active to the inactive list. The present active permissible list contains 170 brand names. The brand names of the permissible explosives placed on the active list are as follows:Black Diamond Nu-Gel No. 4 By test.Black Diamond Special A,do.Burton 11, L. F. By change in name,Burton G, L. F. By test.Columbia B By change in name.Columbia C Do.Columbia D Do.Columbia E Do.Columbia. F Do.Columbia G Do.Columbia 1 Do.Columbia 2 D.Columbia 3 DoColumbia 4 Do.Columbia-Gel 1 Do.Columbia-Gel 2 Do.Genite 5, Do.Genite 7, Do.Genite G Do.Lump Coal C By test.Peerless No, 1 By transfer from inactivePeerless No. 8, L. F. Do.Tri-State Special No. 1 Do.Unilite No. 2 Do."

Dec 1, 1936

Reduce injuries caused by slips and falls from large haulage vehicles. Approach Replace the flexible-cable or chain-type lower ladder steps, with steps that extend closer to the ground and do not sway when stepped on. Modify dimensions of entire ladder to new industry recommendations. How It Works New lower ladder steps are supported by side pieces made of pretensioned, solid-wound, coil springs fabricated from high strength steel. Unlike conventional crash-resistant steps, which flex or swing freely when stepped on, the spring supported steps can maintain the same inclination as the fixed upper portion of the ladder while supporting an average-weight operator. The steps are also highly resistant to collision damage because they yield on impact if rammed into obstructions such as rocks or berms. See photograph.

Jan 1, 1980

Provide an accurate, simple, alternative means of evaluating the safety of mine electrical ground systems which has little or no negative impact on mine productivity. The Traditional Evaluation Method The Code of Federal Regulations requires all mines to safely ground their power systems to earth. Effective earth grounding reduces shock hazards to mine workers operating electrical equipment, protects equipment from damage by voltage transients, and provides a means of detecting and locating ground faults. Once an earth ground bed has been constructed, its level of resistance has traditionally been used to gauge the safety of the entire grounding system. Bed resistance measurements are normally performed using a ?fall of potential? technique with a current return electrode placed at a remote location, If the resistance measured is acceptably low, then the bed is assumed safe.

Jan 1, 1985

By V. R. Miller

The Bureau of Mines has developed a technique to separate and recover the three major components, Pb, Zn, and Cd, from lead smelter flue dust. This research was conducted as part of the Bureau's effort to reduce environmental conflicts and occupational hazards associated with mineral-processing operations and to recover valuable constituents in emissions and effluents. The laboratory process utilizes sulfation roasting of the flue dust followed by water leaching to extract over 95 pct of the cadmium and zinc. Ninety-nine percent of the cadmium was recovered from solution by cementing with zinc dust, and zinc was electrowon from the resulting solution after purification. Zinc electrolysis was carried out in a 1-liter cell at 35° C with a cathode-current density of 8 A/dm2 in a solution containing 65 g/l Zn++ and 180 g/l H2S04, Current efficiencies of 80 pct were obtained. The leached residue consisted largely of PbS04, which was converted to PbC03 and leached with H2SiF6 to produce PbSiF6 electrolyte. Ninety-five percent of the lead contained in the residue was converted to electrolyte. Lead was electrowon from solutions containing 70 gil Pb++ and 90 g/l H2SiF6 using a lead cathode, Pb02-coated titanium anodes at 28° C, and a current density of 1.6 A/dm2. Current efficiencies approaching 92 pct were obtained. Accessory minerals such as cobalt and nickel were separated into purification residues and liquor.

Jan 1, 1982

By D. N. Nilsen

The Bureau of Mines is developing a method to recover Ni, Co, and Cu from laterites containing less than 1.2 pct Ni and 0.25 pct Co. The method consists of the following basic unit operations: (1) reduction roasting, (2) leaching, (3) solvent extraction, and (4) electrowinning. The method reflects three Bureau of Mines objectives: (1) recovery of critical minerals that are domestically in short supply from low-grade domestic laterites, (2) lower processing energy requirements, and (3) solution recycling. This report deals with the extraction of cobalt and the preparation of a suitable cobalt electrolyte by solvent extraction from liquor produced by this method. Nickel and copper are coextracted with LIX64N from an ammoniacal ammonium sulfate leach liquor containing about 1.00 g/l Ni, 0.30 g/l Co, 0.03 g/l Cu, and 0.02 g/l Zn. Cobalt (III) in the nickel-copper barren raffinate is reduced to cobalt (II) with cobalt metal. Reduction of cobalt (III) to cobalt (II) greatly aids subsequent extraction. Commercially available XI-51 extracts about 94 pct of the cobalt from the treated raffinate in one stage in a laboratory mixer-settler continuous circuit. Ammonia loaded on the solvent is removed in two washing steps. About 94 pct of the cobalt then is stripped from the XI-51 in one stage with spent cobalt electrolyte containing about 77 g/l Co and 18 g/l sulfuric acid (H2S04), Electrolytes containing less H2S04 also may be used. Preliminary data indicate that coextracted zinc may be removed from pregnant cobalt eletrolyte containing 3 g/l or less H2S04 with di-(2 ethylhexyl) phosphoric acid (D2EHPA).

Jan 1, 1980

By James J. Hanslovan

Stresses that damage coal mine trailing cables were investigated to obtain a quantified description of cable-stress locations, magnitudes, and frequency of occurrence. Stresses occurring in operating mining sections were measured and observed. Answers to questions that arose during the underground investigations were pursued under controlled conditions, both in the field and in the laboratory. Cable-handling suggestions that minimize or eliminate the stresses are summarized in the form of recommendations to mine operators.

Jan 1, 1979

By Richard L. Sanford

This report summarizes the results of the development of a Directory of Computer Programs Applicable to U.S. Mining Practices and Problems. The Directory includes a sampling of computer usage in operating and manufacturing companies, consulting firms, computer companies, research organizations, universities, and various U.S. government agencies. References to computer applications throughout the mining industry are presented as well as comments on the availability of programs to interested organizations or individuals.

Jan 1, 1977

Permit visual inspection of underground cavities dam the surface. Approach A closed circuit TV camera and a 35mm still camera are lowered down a borehole, and remotely operated. How It Works A platform holding the cameras, and other equipment is lowered on a graduated cable until the depth of interest is reached. Then a quartz lamp and the TV camera are turned on. The television picture is monitored at the surface and recorded on video tape. Areas of special interest are photographed with a 35mm still camera. These photographs contain more detail than TV images because photographic film is capable of higher resolution than a TV transmission.

Jan 1, 1979

By C. E. Jordan

The Bureau of Mines conducted tests on seven samples of Florida phosphate operations.slimes to develop a method to recover phosphate presently being discarded because of its small grain size. A system of hydrocyclones and hydroseparators was used to recover up to 96 pct of the plus 400-mesh material from the slimes. This plus 400-mesh material was subjected to fatty acid flotation, and concentrates containing up to 33.4 pct P205 were produced. As much as 88 pct of the phosphate (P205) was recovered from the plus 400-mesh material, and up to 29.6 pct was recovered from the total slimes.

Jan 1, 1982

By Harold F. Unger

The Bureau of Mines conducted drilling experiments in the laboratory with a commercially available percussive drill that has an independent rotational system. Eight rock types with a wide range of physical properties were drilled under several combinations of rotational speed, drilling thrust, and operating pressure. Penetration rates and energy per unit volume correlated well with the coefficient of rock strength as shown graphically. Size-distribution analyses of some of the drill cuttings show how particle size varies with rotation speed and rock hardness. In general, changing the rotational speed has a greater influence on the penetration rate in softer rocks, with penetration rate increasing with increasing rotational speed.

Jan 1, 1972

By H. R. Shell

The systems MgO-MgFa-SiO2, at 2 and 4 weight-percent Li2O and at 3.8 and 7.7 weight-percent Na2O were investigated by solid state reaction at 1,200° C. The results are summarized in four ternary diagrams. Besides the expected humites and simpler silicates or fluorides, proto-amphibole and water-swelling fluormicas or fluormontmorillonoids were found in the systems containing lithium and monoclinic fluoramphiboles, water-swelling fluormicas or fluormont-morillonoids, and nonwater-swelling fluormicas were found in the systems containing sodium. These latter compounds were not in the base system MgO-MgF2-SiO2.

Jan 1, 1962

By R. H. Sprute

Hydraulic backfill consisting of siliceous mill tailings was successfully dewatered and consolidated by electrokinetics in a field test conducted by the Bureau of Mines at the Star mine, Burke, Idaho. A stope at the 2,000-foot level was filled in such a way that slimes and coarse sand were retained in the scope. Following settlement of solids and decant of surface water, direct current applied between buried electrodes created a firm, dense material in approximately 3 hours. This rapid densification of fine-grained material demonstrated the utility of this method and suggests other applications, particularly in the control of slime deposits that cause serious problems in many deep mines.

Jan 1, 1975

During 1999, there were six fatalities in surface mines involving haulage equipment colliding with a smaller vehicle or person, or backing over the edge of a dump point. All of these fatalities can be attributed to the extensive blind areas around large haulage equipment. Researchers at NIOSH are investigating various technologies that can be used to monitor these blind areas and provide information on nearby obstacles to an operator. So far, the technologies listed below have been tested on dump trucks used in surface mining. The selection of these systems was based on their ability to handle the tough environmental conditions found in mining operations and how well they detected obstacles out to 40 or 50 feet beyond the rear of large dump trucks. Some of the manufacturers of available collision warning and camera systems are also listed.

Jan 1, 2001

By Fred Baldassare, Marcia Harris, Kenneth K. Eltschlager

Surface mine blasting was recently investigated as a potential source of high concentrations of stray gases found in nearby residences of western Pennsylvania. In one incident carbon monoxide was detected in a home and in the other, high concentrations of carbon dioxide were found in a home. Both carbon monoxide and carbon dioxide are by-products of blasting. However, other potential sources of these gases may also exist in a residential setting. In each case, gas chromatography (GC) and carbon isotopic analyses were used to define atmospheric concentrations inside the homes, and to determine the source of a stray gas. Molecular and isotopic analyses provide geochemical evidence as to the origin and source of the stray gas. This paper discusses elements of a stray gas investigation and the analyses necessary to identify the source of a stray gas.