Search Documents

By C. H. Johnson

This paper on the out-and-fill method of mining is one of a series on mining methods published by the United States Bureau of Mines. It has been compiled chiefly from recent publications of the bureau describing in detail mining methods and costs at various mines. Other sources of information were the technical press, the Transactions of the American Institute of Mining and Metallurgical Engineers, the Mines Haudbook, and company reports. References other than those mentioned in Table 1, which lists the mines entering into this discussion and gives general data regarding them, are given in the body of the paper. The authors wish to acknowledge the kind assistance of many operating officials, either through correspondence or in the course of numerous visits to their mines. DEFINITION OF CUT-AND-FILL STOPING The out-and-fill method of stoping is that method in which relatively small sections or slices are taken successively from the lower surface of a block of ground by open-stoping methods, the broken ore being removed and each section filled with waste material before the next is mined. This definition excludes shrinkage stoping, even with subsequent filling; it excludes square-set and fill methods; it excludes the Mitchell slice method, which may be classed as underhand square-setting; it excludes the systematic use of stull sets and filling, which is a variation of square-setting; it excludes any method involving the caving of the ore, walls, or overburden during the process of extraction, although caving may be allowed to take place when the waste fill is withdrawn for use in other stopes; and it excludes any open-stope method without filling. Through variations, which will be discussed later, the cut-and-fill method merges into shrinkage stoping, open stoping, or square-setting. The use of casual timber support, such as props, stulls, or timber cribs for holding up weak portions of the back does not constitute a change from cut-and-fill to square-set mining.

Jan 1, 1933

By K. C. Dean

Fine-sized mineral wastes discarded by ore milling plants require stabilization to prevent air and water pollution. Stabilization has been attained by physical, chemical, vegetative, and combination procedures. Vegetative reclamation is preferred to physical and chemical stabilization but is diffi¬cult to achieve because the wastes are sterile, contain deleterious inorganic salts, and lack the essential nutrients and physical characteristics required for sustaining vegetative growth. Methods now have been developed for attain¬ing vegetative growth on all but excessively acidic, basic, or saline tailings at costs ranging from $120 to $650 per acre. The cost for stabilizing tail¬ings requiring more intensive treatment techniques may range upward to $1,750 per acre. This report summarizes procedures developed by the Bureau of Mines and industry for vegetating amenable tailings, lists costs for the various processes, and suggests procedures that may be applicable for stabilizing saline and pyrite-containing tailings. Ridged planting beds, drip irrigation, and deep-furrow planting techniques are suggested for stabilizing saline wastes. A combination of mill tailings and sewage sludge can be used for pro¬ducing synthetic soils, and layers of sewage sludge buried under a layer of tailings offer promise of inhibiting acid formation from oxidation of sulfides in mineral wastes.

Jan 1, 1974

By G. R. FITT, S. R. B. Cooke, C. W. Davis, V. H. Gottschalk, C. G. Maier, C. E. Wood, R. S. Dean, S. B. THOMAS, John Gross, E. P. Barrett, T. L. Joseph

Lack of funds has prevented publication of much of the metallurgical work of the Bureau of Mines during the past 2 years . The present progress report covers studies in the direct production of iron and steel . The experimental work was carried out in cooperation with the universities of California , Minnesota , and Missouri . Complete reports will be published when funds are available .

May 1, 1934

By Robert L. Lappi

Eight interburden handling concepts are developed for multiple seam area mine stripping operations in central and western United States. They are based on data gathered and analyzed during field surveys, literature reviews and visits to state regulatory agencies in five states. It is concluded that improvement of reclamation practices through selective interburden handling techniques is possible at lower operating costs than currently incurred. Specific multiple seam mining systems are discussed in this report.

Jan 1, 1980

By Wils L. Cooley

Two major grounding topics are covered: mine ground systems and ground-check monitors. Performance characteristics of ground-check monitors for high-voltage surface mine distribution cables and low-voltage underground mine trailing cables are evaluated. Over 20 commercially available monitors are studied to determine their utility. Several monitoring concepts are incorporated into an unusual monitor design, the prototype of which is described in detail. A comparative study of the effectiveness of several alternate methods of grounding surface mine equipment supports the system currently proposed by MSHA. An instrument design to measure earth voltage gradients is described, as well as an instrument design for measuring the effectiveness of dc haulage current return systems. An extreme analysis is made of techniques for measuring earth resistivity and resistance of safety ground beds. Electrolytic corrosion studies of earth electrodes are reported extensively also.

Jan 1, 1979

By C. O. Hawk

A PART of the Bureau of Mines effort to improve the conversion of coal to liquid fuels, batch autoclave tests were made on the hydrogenation of bituminous coal by a dry method, which featured charging the autoclave with dry ingredients only-coal, catalyst, and hydrogen. This innovation, which omitted the liquid vehicle used in earlier work, limited the products to those made from the coal charged. The effects of the common process variables (catalyst, hydrogen pressure, temperature, and residence time) were studied. Tin catalysts showed the highest activity in the widest variety of forms and were the easiest to disperse; dry mixing in the autoclave during the heating-up period usually sufficed. Ammonium molybdate, on the other hand, was inactive when dry mixed, but it compared favorably with the best catalysts known when applied by impregnating the coal with a solution of a molybdenum compound. As a group, metal naphthenates were the most effective; in fact, molybdenum naphthenate was the most active catalyst the Bureau tests disclosed. One-hundredth of a percent of molybdenum in this form (calculated as the metal in weight-percent of maf coal) induced 90-percent conversion of coal. However, because of their high cost, naphthenates have as yet only technical significance in coal hydrogenation. Long residence time and high reaction temperatures tend to increase the amount of thermal decomposition products formed (light hydrocarbon gases and/or char). High hydrogen pressure favors the production of liquids.

Jan 1, 1965

By Max L. Glenn

As part of its goal to minimize requirements for mineral commodities through conservation and substitution, the Bureau of Mines conducted research to develop molybdenum as a potential substitute for superalloys containing the strategic and critical materials, nickel, chromium, and cobalt. Since molybdenum requires protection from oxidation at high temperatures, several complex oxides of the spinel and perovskite structure were investigated to determine which possessed the greatest potential for use as oxidation-barrier coatings. Two spinels (MgCr204 and MgA1204) and five perovskites (BaHfO3, YCrO3, NdCrO3, BaZrO3, and LaCrO3) were selected for testing. Various high-temperature prop¬erties that are important for oxidation-resistant coatings were examined, including diffusion rates of oxygen and molybdenum, recession (vaporization) rates, hardness, erosion resistance, sinterability, reactivity with molybdenum, and ease of application. From the evaluation of high-temperature properties, two spinels (MgCr204 and MgA1204) stand above the other oxides as possible coatings for molybdenum. However, laboratory coatings of MgCr204 at 1,360° C (2,480° F) are equivalent or inferior to currently available MoSi2 coatings; laboratory coatings of MgA1204 may be comparable under limited conditions to currently available MoSi2 coatings at the same temperature.

Jan 1, 1979

By A. A. Berk

Other Federal agencies have been coming to the Bureau of Mines for help with the purchase and utilization of fuel, largely coal, almost since the day the Bureau was created in 1910. The requests covered a wide range of fuel-economy problems and included boiler-water treatment after it became apparent that water-formed deposits on heating surfaces acted as insulators, decreasing heat transfer and impairing fuel efficiency. Dr. Ralph E. Hall, a Bureau of Mines physical chemist determined the reactions that cause adhering scale to form in boilers (7)2 and went on to introduce scientific principles into water treatment for scale prevention (8). Widespread publicity of these achievements increased the requests for help from Federal steam-generating plants. Since no other Federal agency (even those which were more directly concerned with testing water) wanted to provide boiler-feedwater service, the Bureau decided to continue to give requested help to Federal agencies, Later, the Congress endorsed such agency cooperation as an economy measure,

Jan 1, 1963

By Oliver Bowles

From the most remote periods of civilization stone has been used to perpetuate the memory of individuals or to immortalize their noble achievements. Ancient memorials ranged from simple piles of stone (cairns), or single markers, to great obelisks and pyramids or magnificent mausoleums. The Taj Mahal at Agra, India, built of white marble by Shah Jehan in memory of the Empress Mumtaz Mahal, is one of the most beautiful and costly memorials ever built. It was erected between 1632 and 1650 at an estimated cost of $50,000,000 or more and is today an object of unusual interest for travelers. Other magnificent memorials both ancient and modern are to be found in many lands. No sharp line can be drawn between buildings and monuments, because the larger types of memorials such as the Bok Singing Tower, Lincoln and Jefferson Memorials, and mausoleums of various types have features in common with buildings. However, great care must be exercised in selecting a site for a quarry that will produce acceptable monumental stone because appearance as well as quality is of prime importance. The deposit must be of uniform texture and attractive color and must be notably free of knots, hairlines, impurities, incipient seams, or other defects. Many memorials are of polished stone, and spots or streaks that might be virtually Invisible on a natural rock face will appear distinctly on a polished surface. Hence, stone to be polished must be selected with unusual care. However, less flawless stone may be used for hammered surfaces.

Jan 1, 1955

By Richard F. Link, George S. Koch

Through the use of statistical methods, estimates of metal content and tonnage of an ore body made by using data from 18 diamond-drill holes are compared with actual values established with data from 1,829 drift samples. The reliability of the estimates made from the drill holes is assessed in several ways. The relationship of metal content (assay-width product) to grade is explained. It is concluded that useful estimates can be made from 18 drill holes provided that reasonable assumptions are made and certain risks accepted. The ore body investigated is the Don Tomas vein of the Frisco mine, San Francisco del Oro, Chihuahua, Mexico.

Jan 1, 1964

By T. E. Green, E. F. Spano, W. J. Campbell

A combined ion - exchange X- ray spectrographic method was developed and evaluated for determining trace amounts of cobalt and nickel in high - purity tungsten and tungsten trioxide . The sensitivity for both cobalt and nickel is in the range from 0.2 to 0.5 μg ( 0.04 to 0.1 ppm , based on 5 gram samples ) . Accuracy at the 5 to 20 μg level is ±10 percent of the amount present . Approximately 16 hours elapsed time is required for analysis

Jan 1, 1963

By E. Don Dilling, Wm. F. Hergert, J. W. Pennington, C. E. Wood, M. J. Slendlove, H. A. Doerner

"INTRODUCTION The Bureau of Mines began a study of various methods for producing magnesium metal from magnesite ores in 1936 at Pullman, Wash., with the cooperation of Washington State College. This work included a study of the basic principles involved in the reduction of magnesium oxide by carbon, which soon led to the development of a continuous process. In May 1939, a small pilot plant was operated, which included a small single-phase arc furnace with a hydraulic feed mechanism and an oil-spray device for shock cooling the metal vapor. 5/Subsequently, the Ford Motor. Co., Dearborn, Michigan, began a study of this process on a larger scale. A pilot plant with a nominal capacity of 10 pounds of magnesium metal per hour was constructed and operated intermittently. A larger unit with a nominal capacity of 100 pounds of magnesium per hour was partly constructed when war activities prevented experimental work.In the meantime, the process was greatly improved through continued investigation by the Bureau of Mines at Pullman, and these improvements were successfully tested by continuous operation in a small pilot plant having a normal capacity of 4 pounds an hour."

Aug 1, 1945

By P. N. Summerfield

This report describes the first phase of a general investigation designed to ascertain whether an electronic roof-testing device can be developed that will improve the ability to detect "loose" or "drummy" roof rock over that possible by striking the roof with a sounding bar and noting the character of the air vibrations with the unaided ear or the rock vibrations with the fingers. The amplitude, frequency content, and duration of the vibrations produced by striking solid and drummy roof rock with a hammer or sounding bar have been measured. Results disclosed that there is a significant difference between the characteristics of the vibrations produced in solid and drummy roof. This difference is such that the design of an electronic device to indicate quantitatively the condition of the roof rock appears possible. INTRODUCTION The conventional method of roof testing consists of striking the roof with a bar2/ and judging its soundness from the character of the air vibrations heard with the ear and/or the rock vibrations felt with the fingers -a procedure that depends upon the experience and the sensory abilities of the observer. Impact testing of a solid roof rock usually produces a sharp ping or click, whereas impact testing of a drummy roof rock produces a dull thud or drummy sound. This method of roof testing is, at most, only a qualitative test, and many roof rocks are difficult to classify as drummy or solid.

Jan 1, 1956

Five conclusions that emerged from ADL's Contractor Noise Measurements Assessment done for the Bureau of Mines and the 7 December 1971 Bureau of Mines Contractors' Round Table Meeting in Boulder, Colorado were: ? a limited amount of good data has been obtained for characterizing the noise environment for electromagnetic (EM) coal mine operational/emergency communications systems; ? significant noise date gaps still exist; ? suitable instrumentation and data analysis methods are available for filling these data gaps; ? the immediate and most important data gaps should be filled by means of a timely field measurement effort that is purposely limited in scope and duration; ? this field measurement effort should preferably be carried out by a team knowledgeable and experienced in coal mine EM noise measurements.

Jan 1, 1972

The first metal-mine accident-prevention course was prepared and published in 1942-45 as a series of seven miners' circulars (Nos. 51-57). The course has been broadened in scope, revised, and brought up to date and is being published as a similar series of seven miners' circulars (Nos. 51-57, revised) on accident prevention in metal and non-metallic mines. These circulars are as follows: Injury Statistics (Miners' Circular 51), dealing with general statistics on injuries from accidents at metal and nonmetallic mines, including causes, costs, and the use of investigations and reports of all injuries.

Jan 1, 1960

By F. D. Everett

The Federal Bureau of Mines reviewed the status of tungsten deposits of Utah in 1959. Industrial requirements of tungsten during emergencies have exceeded the domestic supply, and a knowledge of the sources of this strategic element may be helpful in the future. Tungsten occurs as the mineral scheelite in deposits that have been developed or explored on approximately 60 properties in 10 of the Great Basin ranges of Utah, none of which were being worked in 1957-59. Ores from most of the productive areas are similar in that they are contained in tactite deposits on or near the contact of calcareous and acidic intrusive rocks. The tactite ores consist predominantly of the silicate minerals garnet, epidote, and diopside and the carbonate rocks limestone or dolomite. Scheelite, where present, is disseminated irregularly in the tactite. Tungsten ores from Utah mainly have been produced from small deposits worked in World Wars I and II and the Korean campaign. The ores were either hand sorted to a grade ranging from 0.5 to 1.0 percent tungsten trioxide (W03) or were beneficiated in small mills to higher grade concentrates. The largest reserve appears to be in the area of the Notch Peak intrusive in the House Range, Millard County. A large part of the reserve in the House Range is mineralized tactite containing 0.2 to 0.3 percent W03. Research on flotation by the Bureau of Mines has indicated a method of concentrating scheelite in tactite ores that average 0.25 percent W03, with at least 85 percent recovery. The concentrate assays more than 5 percent W03 and can be processed into artificial scheelite ready for industrial use.

Jan 1, 1961

By Oliver C. Ralston

Nonmetallic technologic investigations of the U. S. Bureau of Mines are headquartered at experiment stations in three widely separated localities of the United States. During 1936, the Nonmetals Division of the Technologic Branch was formally set up by combining the direction off the work of these three experiment stations under one administration. The New Brunswick (N.J.) station which in the past has been known as the Nonmetallic Minerals Experiment Station, is henceforth to be at College Park, Md., as part of the Eastern Experiment Station, and its principal activities will be related to the nonmetallic resources of the Eastern and New England States.

Jan 1, 1937

By John Gross

Studies in grinding efficiencies carried out at the Midvale plant of the U. S. Smelting, Refining & Mining Co. and at the Tooele plant of the International Smelting Co. Were made possible by the cooperation of these two companies with the U. S. Bureau of Mines. Mr. Alan Probert of the U. S. Smelting, Refining & Mining Co. and Mr. E. C. Peterson of the International Smelting Co., devoted their entire time to the work during the respective tests, and their services are hereby gratefully acknowledged. It is a pleasure to acknowledge also the assistance and kindness of the staffs of both companies in making it possible, at considerable trouble and expense, to sample the entire mill circuits and in furnishing the necessary supplies and special apparatus required in the work.

Jan 1, 1929

The contractor examined L.T. White's Patent No. 3524680 and, finding it in need of engineering refinements, proceeded with a conceptual design of a variable wall mining machine. The contractor then proceeded to assess the feasibility of the variable wall mining machine measured against the criteria specified by the U.S. Bureau of Mines. The feasibility was judged from a physical aspect, a health and safety aspect, and an economic aspect. The Variable Wall Mining Machine was judged to be feasible on all three aspects provided that certain specified practices were adopted. Description The specifications and design and performance parameters of the Variable Wall Mining System as conceptualized are summarized in Tables I and II. The system consists of a side-cutting auger operating in a string of identical 12 ft. sections, along a 500 ft. retreating longwall face. In addition to the 41 identical sections, there is a special drive and discharge section at the head gate.

Jan 1, 2012

By W. G. Park

Long-range projection of demand for domestic crude oil indicates a continued upward movement and accentuates the need for increasing the recovery from known crude-oil resources to supplement expected future discoveries. Consequently, the industry and Government have given special attention to the viscous or heavy-oil deposits because they offer the distinct possibility of large order increases in ultimate recovery. This report presents data pertaining to 150 heavy-oil reservoirs in Arkansas including oil characteristics of samples from 38 of these reservoirs. To January 1, 1967, about 600 million bbl of heavy oil has been recovered from the 150 reservoirs in 63 oilfields; however, about 4.5 billion bbl, or 88 pct, of oil remained in the ground. Of prime importance is that much of this heavy-oil resource is in reservoirs having characteristics considered favorable for thermal-recovery operations. Data for the thermal projects initiated [thus Ear are presented in individual field discussions. Also discussed is the t crude oil supply-demand situation in the State.

Jan 1, 1969