Search Documents

By David A. Lipton

In 1980, the U.S. Bureau of Mines conducted a mineral survey of the 23,500 acre Garcia Mountain RARE II area (No. 5107) in the Los Padres National Forest. Bureau of Mines data indicate a low potential fur gold, silver, and mercury resources. Twenty-nine placer samples, representative of small yardages, showed small amounts of gold or other economic mineral values. Mercury deposits in faulted siliceous rocks in the Franciscan Formation occur north of the area. Similar rocks are in the southwest part of the study area, but apparently contain no mercury deposits. Geothermal and oil and gas potential is low.

Jan 1, 1982

By W. H. Forbes

The prevention of accidents from falls of roof and coal requires a considerable amount of personal judgment , for conditions are different even in adjoining working places in the same mine , and conditions may change from hour to hour even in the same working place as the coal is shot down and loaded . Experience has shown that many men can not or do not exercise enough care to protect themselves from injuries ; moreover , where the foremen have been made directly responsible for the safety of the men under them , accidents from falls of roof and coal have , in many instances , been reduced as much as 50 per cent . There is now no question that careful , constant , and intensive supervision is essential in preventing acci- { dents and more especially accidents of this class . Falls of roof and of coal account for approximately 50 per cent of all coal mine accidents and annually result in the death of approximately 1,000 men and cause lost - time injury to approximately 50,000 men . These and other accidents are recurring with little or no diminution , usually not because of the lack of knowledge of safe and dangerous practices , or of the technique of safety , but largely because of the lukewarm interest of major executives in safety or the failure of mine officials to formulate and to enforce common - sense rules and regulations . When failure is the outcome of a sincere attempt of the managing officials to teach safety to the miner , the fault may usually be attributed to misguided effort . Various solutions for the problem of eliminating accidents from falls of roof or coal have been suggested , some of which are : Standard system of timbering for the specified mining districts ; departure from the room-and - pillar system to a more concentrated system of mining ; more intensive supervision - that is , 1 section foreman for every 25 loaders instead of 1 section foreman for 75 , 80 , or even more loaders the practice in most mining districts . - However , investigations conducted by the writer at numerous mines operated by a number of mining companies in several districts show that employees and officials alike are inclined to work under loose and unsupported roof , relying solely on the " drummy " sound and on their judgment and experience as to whether the roof will stay in place for one hour or for several hours . With but few exceptions , men who had been injured by falls of roof or ccal or were found working under loose and unsupported roof , admitted that they knew of the possibly unsafe condition , but it was their opinion that the roof or coal was not loose enough to fall for some time .

May 1, 1931

By M. M. Fine

This Bureau of Mines report describes the theory, experimental procedures, and the results obtained to date in the development of the Bureau's process for magnetically roasting iron ores using scrap iron as a means of reduction. Since magnetic separation is an operational step common to magnetic taconite plants, the preliminary research studies emphasized only the novel magnetic roasting step. The studies included the use of automobile scrap, ferrous reductants such as borings and turnings, and prereduced pellets. Technical feasibility of the process was demonstrated both on a bench- and pilot-scale. Quality magnetic concentrates with recoveries of over 90 percent were obtained from a direct shipping ore containing 59.5 percent Fe and from fine grained semitaconites with about 30 percent Fe.

Jan 1, 1966

By George A. Morgan

The 53 countries that constituted Africa in 1989 accounted for a significant portion of total world output of a number of mineral commodities. Among the most significant minerals to be produced in Africa were andalusite, antimony, asbestos, bauxite, chromite, coal, cobalt, copper, diamond, fluorspar, gold, lithium minerals, manganese, phosphate, platinum-group metals, and the titanium minerals-ilmenite and rutile, vanadium, vermiculite, and zircon. Despite the underdevelopment of much of Africa, mineral raw materials played a very important part of the national economies of many of its countries. In terms of percent-age of export earnings, minerals accounted for more than 90% in some cases. In several countries with agrarian economies and little economic diversification such as Angola and Guinea, a single mining operation could represent an important source of foreign exchange. These latter operations tended to be the more easily mined surface deposits of diamond, gem stones, and precious metals. Mineral commodities for which Africa had a high percentage of world output were bauxite, 16%; chromite, 44.5%; cobalt, 76.5%; copper, 13.9%; diamond, 50.7%; gold, 32.9%; manganese, 27.1 %; phosphate, 22.1 %; platinum-group metals, 48%; uranium, 29.2%; vanadium, 54%; and vermiculite, 41 %. Several of these, chromite, cobalt, diamond, and manganese, were not produced in the United States.

Jan 1, 1992

By Thomas G. Murdock

ALTHOUGH the contribution of Algeria, including the Sahara, to the local economy and to world mineral supply was small for many years, the spectacular development of an important petroleum and natural-gas industry has changed the position of the country. In 1963 there were decreases in output of most mineral commodities, however oil and gas production forged ahead and established new records. The impact of adverse market conditions and especially the competition from lower cost producing areas was felt by both the metals and nonmetals industries. This and the general economic conditions related to the recovery of the country following the years of strife attending its emergence as an independent state combined to hold back production and development commensurate with resources. The principal events of the year were in the petroleum sector and included the first commercial production from several new fields, some new discoveries, the virtual completion of the first petroleum refinery in the country, and installation of additional pipelines. Progress was made toward the further utilization of the vast resources of natural gas and the provision of additional transportation and refining facilities. In the mining domain the government took over two iron-mining operations, and progress was made towards expanding production of phosphate rock and determining methods of upgrading the Tindouf Iron ores. Completion of the iron and steel plant near Bone was further delayed. The only coal mine reportedly closed down in late 1963.

Jan 1, 1964

By C. B. Manula

This report is volume 4 of at. eleven-volume final report for a Grant completed by The Pennsylvania State University for the Bureau of Mines to develop a dynamic general purpose computer simulation model for underground coal mining. The simulator developed under the Grant has a wide range of possible applications in the design and evaluation of underground coal mining systems from the standpoints of health and safety, productivity, and mine environment: The Master Design Simulator consists of nine free-standing function-oriented subsystem models linked together into an integrated, comprehensive model of an entire mining system. The subsystems comprising the Master Design Simulator include geology and reserves, methane generation, roof support, subsidence, production, rail haulage, cost, water generation,' and ventilation. This volume of the final report describes the Roof Support subsystem of the Master Design Simulator. This model is based on popular roof support practices for different geological environments with related restrictions imposed by the Coal Mine Health and Safety Act of 1969. From geological sections, the model determines the anchor horizon for roof bolts and the density of roof support necessary. The roof support subsystem is tied to both the geology and reserves subsystem and the production subsystem of the Master Design Simulator, but can also operate as a free standing model. Several case studies are presented showing the application of the model. A detailed user's manual, including a program listing, is presented in the appendices.

Jan 1, 1974

By R. J. Gunderman

A conventional trailing cable connection box on a continuous mining machine was modified by the addition of two innovative devices. These are a pressure vent to preclude buildup of high pressure due to an explosion in-side the enclosure, and a grommet-type cable entry to simplify and speedup cable entering procedures. The innovative devices were evaluated for eight and one-half months in a working section of an underground coal mine. Laboratory tests before and after the in-mine exposure show no measurable change in the devices. Following the favorable in-mine evaluation, technical performance criteria were defined to serve as the basis of approval for the use of the innovative devices. Additional tests to measure comparable gripping of the cable by asbestos rope, substitution rope materials and by the urethane grommet-type entry were included in this effort. Also, literature for the last 80 years was searched. Comments are provided as to how the innovative devices comply with 30 CFR Part 18.

Jan 1, 1982

By P. A. Lawless

The objective of the research performed A for the Bureau of Mines on this contract was to develop a portable instrument for the detection of carbon monoxide (CO) in a mine environment. The desired characteristics were sensitivity and specificity for CO with a stable calibration. The sensor of the instrument was to be of metal oxide composition, requiring low power for compatibility with the types of batteries presently used in personal equipment in mines. The solid state design was also desired for ruggedness and small size. A key design feature of the instrument was to be provided by adherence to the intrinsic safety design requirements for electrical equipments operated in potentially exposive mine atmosphere. The Research Triangle Institute has prior experience in developing a solid state oxygen sensor using a thin film of zinc-oxide (Ref. 1) and experience in fabricating thin film devices. Solid state sensors utilized by other workers (Refs. 2, 3, 4, 5, 6) have included metal and semiconductor films and crystals of materials like carbon and aluminum oxide for the measurement of water vapor in the air and have relied upon measuring resistance and capacitance changes in the sensor in response to adsorbed vapors or gases. Since the effect of carbon monoxide in changing the resistance of various materials such as molybdenum, platinum, and zinc oxide had been reported (Refs. 7, 8, 9, 10), the requirements appeared to be realisable, although it was recognized even at the inception of the work that specificity to carbon monoxide might require the incorporation of more than one sensor.

Jan 1, 1976

By Don Conrad, Tom Friend, Bill Wiehagen, Lynn Rethi

On-the-job training (OJT) is a very common method of teaching job skills. Much of the training is done by experienced workers. This paper discusses small investments that can help improve the effectiveness of OJT. Effective OJT involves some structure and planning in the transfer of responsibility for task performance from the trainer to the novice. Assisting the OJT trainer could involve helping develop up-to-date job analyses and offering strategies for teaching and evaluating job skills. The scope of this paper addresses (1) organizational considerations supporting structured OJT, (2) general strategies for structuring OJT, (3) a typical approach for conducting OJT, (4) characteristics and duties of OJT trainers, and (5) limitations of OJT as a teaching method. Health, safety, and operational skills can be connected through training. Haul truck operator training is used to illustrate some of the concepts discussed in this paper.

Jan 1, 2002

By Wilbert J. Huff

For the past 9 years , the technical studies conducted by the Explosives Division of this Bureau have been summarized in a series of reports issued annually . The following account presents investigations undertaken from July 1 , 1943 , to June 30 , 1944. The work is detailed under a number of main headings corresponding to the organizational structure of the Division , the various activities being under the immediate direction of unit chiefs , who report directly to the author . Specific credit , however , is due to the individual unit leader and his assistants .

Jan 1, 1945

By A. B. Hooker, L. C. IlsLey

Explosives have been fired electrically for several decades. Mountains have been tunneled, deep shafts sunk, extensive coal and metal mine workings excavated and, in times of war, railroads, buildings, bridges, and fortifications have been destroyed by means of electrically fired explosives. Modern engineering depends so much on explosives that their safe and efficient handling and especially their detonation are of prime importance to all those connected with the use of explosive agents. Electric shot-firing is only one method of igniting explosives, but it is rapidly spreading and because of certain inherent safety features should be encouraged. Data collected by the Bureau of Mines indicate that in the United States a large percentage of the blasting in quarries, shafts,· and tunnels, and from 15 to 25 per cent of the blasts in mining operations, are set off electrically. The Bureau of Mines is interested in electric shot-firing because of its use in mining, and especially because electric methods, when properly applied, are undoubtedly safer than other methods commonly used. Electrical problems of many kinds must be solved in dealing with the various phases of electric shot-firing. Success in using an electric detonator is closely linked with the resistance of its bridge, the resistance of its leg wires, and the insulation of its current-carrying parts. The proper layout of a circuit where a number of shots are to be fired simultaneously depends not only on the types of detonators that are used and their arrangement and interconnections, but also on the size and insulation of the wire leading back to the source of power, and even on the source of power itself. Various types of electric shot-firing machines have been developed, and these offer still another field for study. In investigations of electric detonators and electric blasting equipment, the oscillograph is valuable because it can record electrical activity over very short intervals of time. By its use more complete information about electrical performance can be obtained than by any other means.

Jan 1, 1926

By J. B. Rosenbaum

Prolonged laboratory and limited pilot plant tests have shown that the Bureau of Mines buffered S02 -H2S process is capable of removing 95 to 99 percent of the S02 from industrial waste gases. Most of the S02 is converted to elemental sulfur; only about I percent converted to sulfate The process comprises (1) washing the flue gas to remove particulates and S03, (2) absorption of the S02 in citric acid or other carboxylate solution, (3) reaction of the loaded solution with H2S in a closed vessel to precipitate the absorbed S02 as elemental sulfur, and (4) separation of the sulfur from the regenerated solution by oil flotation and melting. Two-thirds of the molten sulfur is converted to H2S for use in the sulfur precipitation step by reacting sulfur vapor with natural gas and steam in the presence of an alumina catalyst. The chemistry and mechanism of the process are described, initial laboratory and pilot plant data are summarized, and second-generation laboratory operation and pilot plant design are reviewed. Preliminary cost estimates are presented for recovering sulfur from copper smelter gas, powerplant flue gas, and Claus plant tail gas.

Jan 1, 1973

By Sidney Katell

This report covers the period January 1963 through December 1963; it is a continuation of the series that began with the publication of Information Circular 7516 in October 1949. Also, it is the fifth in a series of reports prepared under a cooperative agreement between the Bureau of Mines and the American Association of Cost Engineers. The agreement provides for the publication of an annual cost bibliography with the work load involved in the preparation shared equally. The abstracted articles, concerned with all facets of cost engineering in the field of chemical and petroleum plants and related subjects, are from the following sources:

Jan 1, 1964

By Lon A. Williams

This report, authorized under Contract Number H0220065, Amendment Number Six, documents the results of an investigation of lighting system modifications and designs for working place illumination in high and low coal entries of underground coal mines. The portable and machine mounted system designs, both modified and prototype, represent a continuation of work performed under Contract Number H0111403, Amendment Number One. See the Final Technical Report dated May 26, 1972 for detailed information concerning this prior Contract. All modified and prototype systems met the performance requirements of Bureau of Mines Specification 2G, as proved by test. In addition, the systems met the requirement for illumination, as specified in the Contract and in the proposed standards which were generated in response to Public Law 91-173.

Jan 1, 1976

By Sidney A. Suhler

A field operable, breadboard model, borehole radar was developed for the detection of hazardous geological anomalies in and above a coal seam in advance of mining. A four-inch diameter downhole probe was fabricated and tested in several environments. The radar transmitter was also employed in a cross-hole or through transmission mode to determine natural geotechnical and man-made conditions between boreholes. Sensitivity to underground conditions in both modes of operation were indicated.

Jan 1, 1978

By Ronald T. Mayerle

There are no producing or developing mines in the Rattlesnake RARE II area. Specific areas with mineral occurences are prospects for: 1) stratabound copper and silver in Belt sedimentary rocks on the northwest border of the study area; 2) base metal sulfides, in thin veins and shear zones in Belt sedimentary rock, and diabase dikes and adjacent metasedimentary rocks in the southern part of the study area; 3) barite in sedimentary rocks near Rattlesnake Creek and Sheep Mountain; 4) limestone near Rattlesnake Creek and Blue Point; and 5) silica in quartz veins near the headwaters of Rattlesnake Creek and Sanders Lake. Stone, sand and gravel suitable for construction material are in the study area; however, equal or better quality deposits are common throughout the region. The RARE II area has no known oil and gas, coal, or geothermal energy deposits.

Jan 1, 1983

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed, Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Arcy, D&apos Banister

Drilling practices at the Silver Summit mine in Shoshone County, Idaho, and the steps taken to increase drilling efficiency are described for the 1952 to 1958 operating period. Mining and development methods are outlined, and drilling equipment and practice are discussed. Cost and performance data include drilling time, bit duty, steel failure, drill repair, and compressed-air consumption. Steps taken to increase drilling efficiency and decrease costs are described, including modifications of bit design, new procedures for drill-rod fabrication and new processes for completing certain drill-machine repairs.

Jan 1, 1963

By Charles E. McCarthy

Part 1 of this report is concerned with the electric-furnace production of calcium aluminate and iron alloy from a variety of siliceous ferruginous ores of aluminum. The furnacing research was directed, first, to determine the extent of the field in the CaO-Al2O3-SiO2 system, in which calcium aluminates with the optimum leaching characteristics are obtained; second, to produce suitable quantities of these aluminate mixtures for pilot-plant leaching tests; third, to investigate the physical chemistry of the reduction reactions during furnacing; and, fourth, to study the economics of the process. The third and fourth steps were not completed. Part 2 comprises another phase of the work and will appear as a second Report of Investigations. It deals with the extraction of metallurgical-grade alumina from the calcium aluminate slag produced in the electric furnace and includes the following steps: leaching, desilicating, precipitating, dewatering, filtering, and washing of the aluminum hydrate. No claim is made that the data are complete, nor has the chronological order of obtaining data been followed. Rather, it is emphasized that additional work is necessary if the full possibilities of the process are to be evaluated. and made available.

Jan 1, 1949

By Corwin L. Cooper

This vapor, which describes mining and milling methods and costs at the Knob Hill gold mine, is one of a series being prepared by the Bureau of Mines on gold mining and milling practices in the United States. The mining properties owned or controlled by Knob Hill Mines, Inc., are situated in the Eureka mining district on a country road 2 miles up Eureka Gulch from the town of Republic, county seat of Ferry County, Wash. The district is about 140 miles northwest of Spokane by road and 35 miles south of the international boundary line. The altitude at the mine office is 2,700 feet.

Jan 1, 1940