Search Documents

The Tenth International Conference of Directors of Safety in Mines Research was held in the United States from September 28 through October 2, 1959, at Hotel Webster Hall, Pittsburgh, Pa. The Conference was organized by the Federal Bureau of Mines. In accord with the program outlined at the Ninth Conference (1956, Heerlen, Holland), the papers submitted dealt with the following three subjects: 1. Safety of coal mine explosives 2. Explosion hazards in mines 3. Ignition and fires in mines Seventy papers were presented. There were eight technical sessions followed by an extended tour of the Bruceton facility of the Bureau of Mines on October 2. Simultaneous translation was provided in the three official languages of the Conference--English, French, and German.

Jan 1, 1962

By Craig M. Jensen

A laboratory assessment of prompt and delayed neutron activation analysis with 252Cf and 14MeV neutron sources, for use as an in-situ method of determining low-level copper concentration has been performed. A simulated borehole using porphyry ore was constructed and varying copper concentrations were simulated using copper rods. Prompt neutron activation analysis experiments were consistant with earlier work and do not appear to be feasible fur copper concentration of 1.5% or less. Delayed neutron activation analysis experiments indicate that copper ore concentrations of less than 0.1% are detectable using either the 511-KeV gamma-ray of copper-64 or the 1039-KeV gamma-ray of copper-66, with high resolution detectors such as Ge (Li) or intrinsic germanium.

Jan 1, 1977

By Joseph A. DeCarlo

The rapid growth of the organic chemical industry in the United States and abroad has focused attention on the future raw-material sources for this important industry. Chemical products are essential to modern civilization; and millions of tons of organic chemicals are used annually, ranging from basic raw materials to finished chemical products such as drugs, cosmetics, and soaps. Hundreds of chemical products are made directly or indirectly from coal, but in this report "coal chemicals" will be limited to crude tar, crud light oil, and ammonia recovered in the high-temperature carbonization of bituminous coal and the important principal products obtained by processing these materials. Specifically these include benzene} toluene, xylene, naphthalene, creosote oil, tar acid oil, pitch, and ammonium sulfate. Therefore the term "coal chemicals", wherever used in this report, includes only these products and does not include the secondary or intermediate products such as styrene, synthetic phenol, aniline, phthalic anhydride, or finished products made from these, such as synthetic rubber, plastics, and dyes. The United States leads the world in production and consumption of coal chemicals. In the past five years nearly one-fourth of the total output of coal-tar crudes in the world was produced in the United States. Consumption of some of the more important products derived from these crudes such as benzene, toluene, xylene, and naphthalene, however, ranged from about one-third to one-half of the world total because of imports and production of benzene, toluene, and xylene from petroleum. The synthetic organic chemical industry of the United States was established during World War I on chemical raw materials obtained by the high-temperature carbonization of bituminous coal but this source of supply currently furnishes less than 40 percent. More than 60 percent of the chemical raw materials used to produce organic and inorganic chemical is supplied by the petroleum industry and production of petrochemicals is rising rapidly.

Jan 1, 1960

By S. Harteis, D. Dolinar

Many mining operations rely on bulkheads to provide a barrier between impounded water or slurry and active mine workings. However, bulkhead failures could cause and have caused catastrophic flooding that puts the underground workforce at risk. The National Institute for Occupational Safety and Health1 (NIOSH) in collaboration with the Mine Safety and Health Administration (MSHA) is conducting research to evaluate the adequacy of existing design practices for water and slurry bulkheads. A key component of this research effort is documentation of the performance history and design parameters for bulkheads installed in underground coal mines during the last 20+ years. This research is part of a larger effort to develop general design guidelines and procedures for constructing and maintaining bulkheads that will help to ensure their long-term structural integrity, while significantly reducing the inundation risk for miners. This paper presents the results of NIOSH’s research to identify state-of-the-art bulkhead designs, including design criteria, leakage monitoring systems, and emergency warning systems. Underground observations and evaluations of existing bulkheads suggest that the most important design factors influencing their performance are the interface of the bulkhead with the surrounding strata and the potential magnitude of the hydraulic pressure to which they may be subjected. When a bulkhead has failed, leakage has generally been through the surrounding strata or along the bulkhead/strata interface, with the failure potential along the interface increasing with hydraulic head. It was also determined that development of a monitoring program to ensure the long term structural integrity of bulkheads is an important safety consideration. Current monitoring procedures range from weekly visual inspections to constant monitoring via pressure transducers and fluid level indicators. Where possible, these devices are used in conjunction with a computer based mine monitoring system to alert mine personnel when an emergency condition exists at the bulkhead installation.

By M. A. Elliott

Diesel-powered haulage equipment has recently been tested and approved for permissibility by the Bureau of Mines for use in mining in the United States. Achievement of this advance in safety involved extensive studies, both in the testing station (2, 3, 20, 21, 22, 23, 24, 25, 26, 27)3/ and in the field 1, 4, 13, 30), of the operating characteristics of diesel engines in relation to the toe of such engines underground. The results of these studies formed the basis for establishing the requirements that should be met by diesel-powered haulage equipment approved for permissibility. Considerable interest has been manifested in the development of diesel-powered haulage equipment fur mines. The purpose of this paper is to retrace briefly the course of this development and to answer such questions as: What is the history of the use of diesel engines underground? Why has the Bureau of Mines been interested in the development of diesel-powered haulage equipment for use in mines?

Jan 1, 1953

By K. R. Dorman

To develop the potential of precast concrete sets as a support medium in underground mines, a three-piece precast concrete drift set was designed for a small opening and tested to destruction in an underground straining frame. Thirty-six tests were made with three sizes of members using three different loading conditions. In addition, 14 members were tested individually in the laboratory. Test results are compared with theoretical calculations. A cost comparison shows the use of concrete sets would be advantageous where conventional wooden timber requires excessive replacement.

Jan 1, 1968

By Charles L. Kimbell

The year 1977 generally was a year of growth in overall world mineral industry activity, although there were downturns in major elements of the world's iron and steel industries. The sharp upturns in market economy nation activities that were noted in 1976, following the reduced performance levels of 1975, were moderated, and in the centrally planned economy nations, overall mineral industry activity apparently continued to increase, but at a pace in keeping with that of 1916 rather than at the higher rates of the earlier 1976's. Noteworthy during the year, if only in a negative sense, was the inability of world powers to reach any significant agreement on issues relating to deep seabed mining. Interest from a commercial viewpoint centered around deposits or so-called manganese nodules. These materials, which indeed are chiefly manganese in terms of their content on a quantitative basis, really were of commercial interest primarily far their copper, nickel, and cobalt content. Participants at the Third United Nations Law of the Sea Conference looked into seabed mining rights, but reached no mutually agreeable decisions.

Jan 1, 1981

Coal, America's most abundant fossil fuel, is expected to play a key role in our pursuit of energy independence. A substantial increase in coal exploitation will be required if we are to fulfill our future energy needs. It is essential that new developments continue if stable coal prices are to be achieved and maintained. The challenge of the mining industry is to continue these developments in the face of problems related to increasing labor costs, inflation and environmental restoration. With expectations of increased activity in surface coal mining, the U.S. Bureau of Mines has authorized this study to determine the preliminary economic and technologic feasibility of underspoil haulage in area strip coal mines and to identify geologic and geographic areas where such a system could be used. These objectives were met by literature search, data-gathering visits to several active area strip mines and by analyzing various haulage systems that were superimposed on three model mines. Potential advantages of such a system include: 1) improved mine design; 2) lower mine operating costs; 3) improved land reclamation; 4) lower manpower requirements; 5) lower mobile equipment requirements; and 6) smaller, less sophisticated maintenance facilities.

Jan 1, 1975

By W. H. Strickland, R. H. King

Ultrasonic ranging sensors are inexpensive, have no moving parts, have no lenses to clean, are normally small and unobtrusive, and can measure distances through moderate amounts of dust, smoke, and humidity, so they are well suited to underground mines. In the work reported here, conducted by the U.S. Bureau of Mines, researchers tested ultrasonic ranging sensors for their abiity to define rib line features for computer-aided navigation of underground mine mobile equipment. The investigation began with laboratory tests of field of view, angle of incidence, intersensor variation, and ranging accuracy of the individual rangers in a ring array produced by Denning Robotics of Wilmington, MA. The results showed that the sensors have good accuracy and low variability. Additional experiments at AMAX's Henderson Mine showed the sensors could accurately and reliably measure the distance to mine features, including convex and concave corners and rib intersections. The results showed that when used properly, the ranger data are accurate enough for reliable mine vehicle navigation When used incorrectly, ultrasonic rangers do not provide the anticipated data. Therefore, this report explains the principles of ultrasonic range measurement, describes the ranger's strengths and weaknesses, and explains proper ranger use and data analysis.

Jan 1, 1993

By G. R. Hopkins, A. B. Coons

A survey of the petroleum pipe lines by the Bureau of Mines as of May 1, 1923, shows that on that date there was a total of slightly more than 90,000 miles of pipe lines in the United States, having a capacity of approximately 15,750,000 barrels, which is equivalent to one-fourth of the nation's average production for one month. These lines varied in diameter from 2 to 16 inches, the weighted average being 6 inches. The total pipe-line milenge was about equally divided between trunk lines and gathering lines, though the capacity of the former was about four times that of the latter. This was due, of course, to the difference in average diameter, that for the former being 7.4 inches as compared with 3.7 inches for the latter. The common size for trunk lines was 8 inches, and for gathering lines 2 inches. Oklahora, with 19,180 miles of pipe lines, is the leading State in total mileage, with Texas second and Pennsylvania third. From point of trunk lines alone Texas is considerably ahead of any of the other States, a position which it owes to its size and to the growth in the rovement to its Gulf ports. Cali- fornia, though the leading State from point of production, ranks only seventh in pipe-line mileage. This is due to the fortunate location of the Los Angeles Basin fields, some of which are within sight of the refineries to which their oil is delivered or of the port of San Pedro through which their oil is shipped. The last survey of this nature, made in the spring of 1924 by the U. S. Geological Survey, recorded a total mileage of nearly 83,000 with a capacity of approximately 14,450,000 barrels. This indicates an increase of 9 per cent in both mileage and capacity during the two years.

Jan 1, 1927

By A. N. Fried

With the growing importance of fluid injection in recent years, the petroleum industry has been investigating and field- testing a variety of new methods designed to modify the physical properties of reservoir oil to improve the efficiency of gas and water injection. These procedures include condensing-gas drive, LPG (liquefied petroleum gas) injection, alcohol-slug process, high-pressure-gas displacement, detergent-solution flooding, and in situ combustion (30, 37).3 A new and different method to increase the effectiveness of gas and water injection has been tested by the Bureau of Mines, Consideration of both fundamental and practical factors that operate to limit the oil recovery attain- able by conventional oil-displacement mechanisms led to the concept of a displacement mechanism called the foam-drive method. This report describes the experimental study that tested this concept in the laboratory.

Jan 1, 1961

By B. W. Gandrud

To say that the treatment and handling of the "fines" is the most difficult phase of coal preparation is probably an understatement of facts. It is the fine sizes from about 1/16-inch to 0 that are mainly responsible for the inescapable sludge and slurry problems at plants using wet methods of preparation. Sludge and slurry are a problem from the standpoints of both cleaning and dewatering. They cannot be cleaned satisfactorily by "gravity" methods, which are used so extensively on coarser Sizes, due to the fact that fine sizes, particularly from 65-mesh to 0, do not follow the same laws of settling as do the coarser sizes. Although fine sizes are cleaned more successfully on wet-wash tables than in jigs, even tables as usually operated in coal-preparation plants fail on sizes below 100-mesh. As to other phases of the, sludge and slurry problem, wet coal preparation plants are almost universally beset with troubles in connection with the recovery and dewatering of the fine sizes from about 14-or 20-mesh to 0. The sizes finer than 100-mesh further complicate the problems in a wet preparation plant by their tendency to stay in suspension and build up a troublesome load of solids in the circulating water. In order to prevent too much trouble from this source, it is, customary at most plants to bleed a fair-sized stream out of the circulating system continuously and replace it by addition of fresh make-up water. The slurry water withdrawn from the circuit is usually run to waste, in which case it carries with it a considerable amount of fine coal, thus increasing the "washer loss." Another evil results from wasted slurry water in that quite often it finds its way into creeks and larger streams, creating stream-pollution problems.

Jan 1, 1948

By G. E. McClelland

The Bureau of Mines investigated chemical methods for producing high- purity gold from precious-metal-bearing zinc precipitates and steel wool cathodes. Precious-metal-bearing zinc precipitates and steel wool cathodes are unrefined products from conventional cyanidation and heap leaching-cyanidation operations. The zinc precipitates contained 14,40 pct Au and 0.35 pct Ag. The precious-metal-bearing steel wool cathodes contained 20.65 pct Au and 4.84 pct Ag. The precipitates and cathodes were treated with dilute acid to solubilize the silver and/or base metals. The gold-bearing residue was leached in dilute aqua reqia to solubilize the gold. High-purity gold was precipitated from the aqua regia solution with oxalic acid, sulfurous acid, sodium bisulfite, and gaseous sulfur dioxide. The leaching-precipitation experiments recovered 99.9 pct of the gold. The gold precipitates ranged in fineness from 997 to 999 fine. The chemical refining method provides a viable technique for the smaller operator to produce high-purity gold without using pyrometallurgical refining methods.

Jan 1, 1985

By John A. Breslin

This publication provides an historical overview of research undertaken by the U.S. federal government over the last 100 years to improve the health and safety of our nation?s miners. Federal research efforts began with the establishment of the U.S. Bureau of Mines (USBM, or the Bureau) in 1910. They have continued over the past century, even after the Bureau?s closure in 1996. It is hoped that this publication will give the reader an appreciation for the work of mining health and safety researchers over the past century, and of the miners served by this research. Although not a comprehensive history, this report highlights the key organizational changes made within the Bureau and the federal government that affected mining safety and health research. Some mention is also made of Bureau research not directly related to mining health and safety. Note that the work classified as safety and health research has varied over the last century. For example, before 1970 the Bureau separated mining research and safety and health research. At that time, mining research included ground control and methane drainage because they had direct implications for mine safety. Explosives research was also reported separately from health and safety, even though permissible explosives research was obviously related to safety. Therefore, where budget figures from the Bureau are mentioned in this report, it is often not possible to separate safety and health research from other types of research. This history is generally chronological, with a few exceptions. Because of their prominence and direct links to Bureau research, most of the Public Health Service mining studies completed before 1970, when NIOSH was established, will be discussed in a single section, even though the work spanned many decades. Likewise, for convenience, the brief histories of the Bureau?s mining research centers are located in one section.

Feb 1, 2010

By Allan E. Martin

As part of a comprehensive investigation of tae mechanism of desulfurization of iron and steel by slags, the Blast Furnace Studies Section, Metallurgical Division, Bureau of :lines, in cooperation with the Institute of Technology., University of Minnesota, has made a study of the forms in which sulfur occurs in blast-furnace slag. This report presents data on the three sulfides most important in iron smelting, namely, ferrous sulfide, manganous sulfide, and calcium sulfide. The tendency of these sulfides to form colloids in the molten slag was determined by an examination of quenched samples with an ultramicroscope. Vogt5/ conducted experiments on sulfide silicate melts and examined synthetic blast-furnace slags in a partly crystallized condition. His conclusions were that FeS, CaS, and MnS, or isomorphous compounds, such as (FeXCay)S and (MnxCay)S, were precipitated from the melt, depending on the composition of the slag. In all specimens sulfides were visible and were spherical.

Jan 1, 1941

By E. D. Palmes

A new type of personal sampler for quantitative estimation of atmospheric concentrations of contaminant gases was first reported from this laboratory in 1972. The sampler requires no pumps or flow regulators and employs instead the motion of the gas molecules them-selves to furnish the power for sampling. Under this grant, work was completed on development of a kit for the field determination of both NO2 and NO. Detailed instructions for the preparation of the samplers and the use of the kit was supplied to the Technical Project Officer. Attempts were made to adapt the same type of sampler to the measurement of SO2 and CO. Both gas chromatographic and turbidimetric procedures for the final estimation of the S02 proved to be unsatisfactory. For CO no reagent was found which would react sufficiently rapidly with this gas to utilize the essential feature of the diffusion sampler, the maintenance of a diffusion gradient which is at least approximately numerically equal to the ambient concentration. A number of publications on use of the NO2 sampler, both at occupational and community air pollution levels, have resulted from this work.

Jan 1, 1979

By S. P. Holt, Robert S. Sanford

"INTRODUCTION The wartime demand for iron ore and alloy steel on the west coast revived interest in iron reserves in western United States and Alaska. Magnetite was known to have been the most abundant metallic mineral at some of the old copper mines on Prince of Wales Island. In the summer of 1942, the Bureau of Mines began a program of preliminary investigation followed by core-drilling two magnetite deposits on the island.The Poor Man iron deposit on Kasaan Peninsula, Prince of Wales Island, Southeastern Alaska, was examined in August 1942 by Robert L. Thorne, associate mining engineer of the Bureau of Mines, and John C. Reed and B. N. Goddard, geologists of the Federal Geological Survey in September 1942 the area was mapped geologically and a magnetic survey was made by the Geological Survey. In October and November 1942, a more thorough preliminary examination, which included cleaning out and sampling old adits and trenches, was made by thesenior author, Robert L. Thorne, and Aner W. Erickson, engineers of the Bureau. J. G. Shepherd, a consultant of the Bureau, spent two weeks in March and April 1943 investigating the Poor Man and other deposits on Kasaan Peninsula. Core drilling was completed in June 1943.L. A. Warner, of the Geological Survey, examined all cores and interpreted structural data revealed by the drilling."

Oct 1, 1946

By Charles L. Kimbell

For the world mineral industry as a whole, the year 1981 was a period of continuation and, in some instances, an acceleration of negative trends extending back into 1980. Most available statistical data reflected stagnation or downturns in activity. Levels of production, trade, and consumption declined for a substantial number of leading mineral commodities, including, most notably, steel and petroleum. Investment, if not lower than in 1980, was evidently increasing at a more modest rate. Prices for major mineral commodities were generally lower, at least in terms of constant dollars, and in some cases even in terms of current dollars. Prospects of a major reversal of these patterns seemed dim. The mineral industry, however, was far from alone in this general downturn; most other elements of the national economies of the world's nations fared little better. General conditions of inflation, recession, and reduced industrial product consumption were reflected in most other sectors of the total economy. International political events continued to influence mineral output and flow but had less influence on overall levels of activities than on the geographic distribution of these activities. The Iran-Iraq war certainly played a role in reducing mineral industry activities in those nations, but the commodity most affected, petroleum, was available from other sources in sufficient quantity that, in the face of reduced demand, a substantial surplus developed.

Jan 1, 1983

Workers in underground stone mines have a high fatality rate caused by falls of ground from the mine roof or rib. NIOSH recommendations to reduce ground fall injuries and deaths address baskets, mechanical scalers, mechanical bolters, drill steel changing, personal protective equipment, and training. Description of Exposure An informal National Institute for Occupational Safety and Health (NIOSH) review in 1998 identified approximately 17 new underground limestone operations in vari¬ous stages of planning; as many as 35 new underground stone mines are expected by 2005. Many of these new underground stone mines will employ new or inexperienced workers with minimal knowledge of the hazardous conditions that exist underground. Workers in underground stone mines have a fatality rate nearly 20 times that of workers in the manufacturing sector. Three quarters of the fatalities in underground stone mines are caused by falls of ground from the mine roof or rib (Figure 1) [Statistical Abstract of the United States 1985-1999; MSHA 1983-1999]. During 1983-1999, nonfatal ground falls resulted in 140 injuries, or 15% of all underground, lost time stone mine injuries. These nonfatal ground fall injuries resulted in more than 13,800 lost workdays (one third of all lost workdays). Ground falls generate more disabling injuries and time away from work than any other type of incident. [ ]

Jan 11, 2003

By W. H. Young

The thickness of the coal seam is one of the more important items influencing the productivity and general overall efficiency of operation of a coal mine. The average thickness of coal seams mined in the United States has changed very little in the past 40 years. The first measurement of thickness of bituminous coal and lignite seams was made for 1920, when the average thickness was 5.3 feet.4/ The average thickness for later years was as follows: 1945, 5.4 feet; 1950, 5.3 feet; 1955, 5.2 feet; and 1960, 5.5 feet.5/ Table 1 includes data on number and production of bituminous coal and lignite mines classified by I-foot intervals of seam thickness mined in 1920, 1945, 1950, 1955, and 1960. Though bituminous coal and lignite are mined today from seams of exceedingly variable thickness -less than 2 feet to more than 50 feet - a large majority of the production, 62 percent in 1960, came from seams 3 to 6 feet thick. This is not surprising since the coal seam of moderate thickness presents the least mining difficulties.

Jan 1, 1962