Search Documents

By Sandip K. Mukherjee

This report presents the results of the economic analysis of several applicable alternatives to increase airflow in four underground coal mines. Pressure-quantity surveys were conducted underground and measurements were also made at the main mine fan(s). The existing ventilation networks were modeled using the modified Penn State ventilation simulator. The applicable alternatives were simulated. Performance data obtained from these simulation runs were utilized to conduct the cost-effectiveness analysis. The costs for each of the alternatives included capital, operating and maintenance costs. These costs were expressed as annual ventilation costs per active section in terms of dollars per elm taking into account the economic life associated with each of the alternatives. The benefits were expressed as increased airflow quantity in the critical sections. A section of this report also deals with comparison of simulator predicted air quantity values against air quantity values measured underground. The computer outputs for each simulation run are presented in Volume II of this report.

Jan 1, 1983

Under the Bureau of Mines Research Contract Number H0252071, Foundation Sciences, Inc. has compared the relative effectiveness of roof bolts installed at an angle over the rib with that of bolts installed vertically at the rib side, The information gathered during this investigation was sufficient to supply supplementary information on the mechanics of roof support systems and the general acceptability of field instrumentation methods. During the 140 days of field investigation, 235 bolts were installed, 45 inclined and 190 vertical, in two adjacent intersections. Of these 235 bolts, 30 were in-stalled with load cells and 38 were tested for anchor capabilities. In addition to this instrumentation, the deformation of the opening was measured by convergence meter on 9 lines throughout the two testing areas, and a borescope and photo-elastic gauges were utilized to obtain information on the roof action beyond the surface.

Jan 1, 1977

By N. R. Dixon

This report summarizes all work performed under U.S. Bureau of Mines Contract No. J0395028, "Noise Control of Rubber-Tired Front-End Loaders Used in Surface Mining. " Two loaders, a Caterpillar 988 and an International H-400B, were chosen for this program, and the noise sources and acoustic paths that contribute to the operator's noise exposure were identified. Retrofit noise control treatments were designed and installed on these loaders, and noise reductions of more than 10 dBA at the operator position were achieved on both machines. The retrofit packages are low cost and have been field tested in two mines for more than two years. The results of the program were communicated to the mining industry through a series of noise control workshops and a field manual. The workshops were given in nine states across the U.S. and more than 440 manuals were distributed An audio/visual slide presentation was also developed which the program.

Jan 1, 1983

By R. V. Ramani

One area of study in the Coal Mine Injury Analysis project was to illustrate and enhance the ability of mine safety management personnel to apply analytical techniques to injury experience data and to justify requests for funds for safety enhancement actions on a cost/benefit and other quantitative basis. Four volumes of this final project report detail (1) the objectives and scope of the mine safety management research, (2) the results of literature review, and case studies, and (3) models developed for mine safety management. The four volumes are titled as Volume III: Mine Safety Management, Volume IV: Analytical Techniques for Mine Safety Management; Volume V: Mine Safety Management Case Studies and Volume IX: Training Cost Model. This volume deals with the development of a microcomputer based training cost model (TCM) which can be used to analyze training cost implications of various types of training. The model has been developed using Aston Tate's dBASE III plus language. The computer program and a test run of the model are presented in this report.

Jan 1, 1993

By Kenneth M. Maas

The Bureau of Mines inventoried all lands in Alaska to determine the availability of land for oil, gas, and coal leasing. Acreage for onshore oil, gas, and coal basins was digitized as was land ownership data. Regulatory policy concerning oil, gas, and coal leasing for various government agencies and private concerns was determined. Oil and gas basins underlie 79.4 million acres of Alaska's 378 million acre landbase. Federal agencies manage 44 million of these acres. The Bureau of Land Management is the lead agency for most oil and gas leasing on Federal lands. Lands have to be specifically opened for oil and gas leasing to be available. The state of Alaska manages 21.1 million acres underlain by these basins. More than 80 percent of this acreage is available for resource development. Native corporations manage the remaining 14.3 million acres of favorable oil and gas land. Coal basins underlie nearly 51 million acres of Alaska. Of this land, 26.4 million acres are under Federal jurisdiction. The state manages 17.3 million acres of land underlain by coal basins. Nearly 7.3 million acres of favorable coal lands are managed by Native corporations.

Jan 1, 1991

By L. A. Stinnett

An investigation of hazardous surface openings of abandoned and inactive underground mines in the Black Hills area of South Dakota has revealed: (1) tracing legal ownership of mineral claims via county courthouses is confusing, complex, and oftentimes misleading, (2) in general, the selected mine openings in this investigation are to be considered relatively high in risks and hazard potential which poses a threat to the general public, (3) mine closure procedures and designs can generally be categorically implemented depending on the overall situation of the particular mine opening with subsequent unit costs estimates, (4) few preventive state or federal legal measures exist to date concerning mine closures, and (5) liability damages relating to mine opening accidents usually involve expensive and complex common law cases.

Jan 1, 1979

By Roy F. Abernethy

All samples tested showed some loss of heating value for the 5-month period under all 4 storage conditions. The losses increased as the time of storage increased, with the pan-storage samples showing somewhat greater losses than those in cans. The individual daily analyses for the first 2 weeks and the analyses every other day for the third and fourth weeks of storage vary within the approximate tolerance of the test for heating value. During the first 2 months of storage the changes in heating values were not Significant for the samples from Pennsylvania, Indiana, and Colorado. The Ohio coal indicated some loss by the end of I month, which increased to a value measurable with certainty by the end of 2 months. These data show that (1) small changes may occur even to samples in closed cans and (2) the laboratory sample should be handled as expeditiously as is practical until the analysis is completed. The statement by the ASTM that "If the B.t.u. determination is an important consideration in the sale of coal, the time elapsed between sampling and analysis shall not exceed 30 days,"3/ is quite adequate for 3 of the 4 coals tested. The change in the Ohio coal stored for 30 days is merely indicated and could not be determined with certainty by the techniques normally employed. The data on free-swelling indexes determined on can samples, after 30° C. air drying, show that only the Indiana coal lost more than one unit in free-swelling index number in 120 days. No significant changes were observed with the samples from Pennsylvania, Ohio, and Colorado in the 5-month period.

Jan 1, 1958

By Robert L. Rough

The 1954 field tests consisted of six experimental shots in relatively deep holes in a sandstone similar to many oil-bearing sandstones. Water-injection measurements were made before and after each shot to establish the change in conductivity of the fluid caused by the shot. The pressure pulse produced by the shot was recorded in nearby holes to monitor the shot and to determine if any relation existed between the change in conductivity and the nature of the pressure pulse. The results of water-injection tests showed the range of conductivity of fluid before and after shooting with two different types of explosives. Because of the large spread in data for similar shots, not enough information was available to evaluate the differences in increased conductivity produced by the two explosives or any relation between the increased conductivity and the nature of the pressure pulse. However, these results, with the results of other tests involving explosive shots in rock, provide guidance for future research on the oil-well-shooting problem.

Jan 1, 1957

By Oliver C. Fursman

These investigations were conducted to determine conditions for recovery of nickel and copper from Funter Bay, Alaska, sulfide ore and recovery of nickel from nickel-silicate ore, Nickel Mountain, Riddle, Oreg. Samples of Funter Bay cupriferous and nickeliferous pyrrhotite ore, were treated by beneficiation, roasting, electric smelting of roasted are for matte production, chlorination, leaching, and sulfatizing roasting with subsequent leaching. Funter Bay and Nickel Mountain ores were smelted together to produce matte. Total sulfide flotation, followed by magnetic separation of the tailings to recover entrained nickel-bearing pyrrhotite, resulted in the highest nickel recovery in beneficiation tests on Funter Bay are. Overall beneficiation resulted in recovery of 98.5 percent of the copper and 95.4 percent of the nickel in the concentrate that contained 3.5 percent copper and 1.7 percent nickel.

Jan 1, 1962

By A. G. Starliper

Laboratory studies were made to produce whiskers of tungsten over a wide range of operating temperatures. Hydrogen reduction of tungsten hexachloride in a vacuum furnace at temperatures from 2,7000 to 3,3000 C yielded a small quantity of tungsten whiskers, provided a low degree of supersaturation was maintained. Direct measurements of 3,000,000 to 4,000,000 psi were obtained for the ultimate tensile strengths of individual whiskers averaging 3 to 4 microns in diameter with average aspect ratios of 1,000. This compares with strengths of 300,000 to 400,000 psi for 13-micron-diameter commercial filaments.

Jan 1, 1968

By Charles B. Carpenter

In general terminology, the West Texas Permian Basin comprises the area south of the Texas Panhandle and west of the Bend Arch or Central Basin region. It is outlined mere definitely by geologists, however, as that area underlain by the south half of the Permian Salt Basin4/ and includes Scurry, Mitchell, Sterling, Howard, Glasscock, Reagan, Crockett, Upton, Midland, Martin, Gaines, Andrews, Ector, Crane, Pecos, Ward, Winkler, and Loving Counties in Texas, and Lea and Eddy Counties in New Mexico. The oil fields of the area, of which more than 70 have been discovered, are shown in fire 1. Approximately 4,200 producing oil wells have been drilled in these fields. Oil has been produced from limestones and dolomites of Permian age in most of the fields in the West Texas Permian Basin. Some of the fields produced oil from sandstone beds above the limestone, and in two fields production has been found below the limestone in formations of Ordovician age.

Jan 1, 1936

By W. H. Somerton

Many oil-producing formations contain significant amounts of clay. Because of the large surface area and reactivity of such surfaces, the response of the formations to various recovery processes may be dominated by the reactions of fine-grained minerals, including clay minerals, in the formations. Thus, the success or failure of enhanced oil recovery (EOR) methods may be controlled to a large extent by the amount and nature of these minerals in the formations to which the methods are being applied. One of the deterrents to the successful application of chemical EOR methods is the loss of chemicals injected into the formation, to non-oil recovery processes. These chemical loss processes include adsorption onto mineral surfaces, chemical reactions with rock and fluids in the formations, possibly leading to precipitation and plugging of the formation, and trapping of chemicals in parts of the rock structure so that they become unavailable for displacing oil. Chemicals that may be injected include surfactants, polymers and caustic solutions which react with organic acids in the crude oil to produce surfactants in-situ. These losses are most pronounced in fine-grained reservoir rocks containing substantial amounts of clays.

Jan 1, 1984

By Charles Findlay, Stephen Krickovic, J. E. Carpetta

As one of its projects for degasification of major panels of coal prior to mining within them, the Bureau of Mines conducted methane emission studies during development of a set of three headings 1,800 feet in a major coal panel (2,700 by 3,500 feet) which had been completely isolated by sets of main headings for 12 months in the Federal No. 2 mine (Pittsburgh coalbed) in northern West Virginia. Similar emission studies were conducted in the development of two sets of main headings in virgin coal areas nearby. Comparing the two sets of data indicated that the isolated coal panel had been degasified by approximately 70 percent.

Jan 1, 1973

Early American history is filled with records of the search for and extraction of minerals-a Northwest passage to the treasures of the Indies-an overland route to the goldfields of California. Mining and its associated minerals industry have heralded advancing civilization throughout the ages. The two basic resources on which we all depend for our food, clothing, shelter, and other comforts are agriculture and minerals. Our endowment and how we use it; the spirit and industriousness of our people; our form of social organization all converge to make up our standard of living-our way of life.

Jan 1, 2012

By Jacqueline A. McClaskey

The U.S. Bureau of Mines (USBM) Information and Analysis Directorate collects worldwide data on virtually every commercially important non fuel mineral commodity. These data form the base for tracking and assessing the health of the minerals sector of the U.S. economy. The USBM's data collection activity was instituted by the 47th Congress in an appropriations act of August 7, 1882 (22 Stat. 329), which placed the collection of mineral statistics on an annual basis. The most recent authority for the USBM survey activity is the National Materials and Minerals Policy, Research and Development Act of 1980 (Public Law 96-479, 96th Congress). This act strengthens protection for proprietary data provided to the U.S. Department of the Interior by persons or firms engaged in any phase of mineral or mineral-material production or consumption.

Jan 1, 1993

By Sidney Katell

This study estimates capital investment, operating costs, and selling prices for four underground bituminous mines producing coal with annual production ranging from 1.06 to 4.99 million tons. It is assumed that the mines have a 20-year life. Wages and union welfare payments are considered as of December 6, 1974, under the Bituminous Wage Agreement of 1974, and costs for material and equipment are based on 1975 indexes. Initial capital investment ranges from $20,799,800 for the 1 .06- million-ton-per-year (MM tpy) mine to $84,027,500 for the 4.99-MM-tpy mine. Total capital investment ranges from $32,506,800 to $1 22,983,500 for the same mines. Corresponding selling prices for the coal range from $12.87 to $11.64 per ton, assuming a 15-percent discounted cash flow rate of return after Federal income taxes.

Jan 1, 1976

Underground coal mining continues to evolve in the U.S., and more reserves are being mined under deeper cover, with worse roof, or with interactions from previous workings. At the same time, the mining community is responding to higher safety standards and intense competitive pressures. The need for effective ground control design has never been greater. Ground control safety issues that have been addressed by recent the National Institute for Occupational Safety and Health (NIOSH) research include: Improving roof support performance; Maintaining safe tailgate escapeways from longwalls; Optimizing pillar design for retreat mining; Controlling multiple seam interactions; Predicting roof conditions during extended cuts, and; Preventing massive pillar collapses. As funding from both government and the private sector has diminished, the emphasis in research has focused on providing the mining community with practical techniques for improved ground control design. Many projects have successfully employed empirical methods that emphasize the statistical analysis of case histories from underground mines. Other projects have employed numerical models and large-scale laboratory testing of roof support elements. Using these data, NIOSH has developed an entire toolbox of computer programs that have been effectively transferred to the mining community.

By Basil Dimitriades

The roles of hydrocarbons and nitrogen oxides in smog formation were investigated by the Bureau of Mines. Samples of automobile exhaust with varying HC and NOx levels were irradiated in a smog chamber under conditions that resulted in smog levels similar to those observed in the atmosphere. Results were used to define the patterns that describe the dependence of a number of smog manifestations on HC and on NOx. Using these dependence data and some simplifying assumptions, estimates were made of the ranges within which HC and NOx must lie in order to obtain specified levels of air quality.

Jan 1, 1970

By Noel N. Moebs

The coal wants at the Westland Mine in southwestern Pennsylvania consist chiefly of elongated, sandstone-filled channels with slickensided basal contacts. Tentatively identified as washouts, these channels are about 1,000 feet long and 300 feet wide, are erratic in occurrence and trend, and are difficult to delineate from the customary core drilling pattern. Roof conditions are hazardous adjacent to the washout contact, but roof stability is generally unaffected greater than 30 feet away.

Jan 1, 1981

By Wilton Johnson

The Bureau of Mines study indicates that land utilized by the mining industry for mineral extraction and processing from 1930 through 1980 amounted to 5.7 million acres, or 0.25 percent of the land mass in the United States. Land reclaimed by the industry during the same period was 2.7 million acres, or 47 percent of the land utilized. Land use by the mining industry includes surface land used for excavation or mining, for waste from underground mining, and for wastes from milling or processing operations. Data on land use for disposal of overburden waste from surface coal mines and on areas affected by subsidence associated with underground mining are included for the period 1930-71 only. The 10 leading States in total land used for mining over the 51-year period were, in decreasing order, Pennsylvania, Kentucky, Ohio, Illinois, West Virginia, Florida, Indiana, California, Alabama, and Missouri. Seven mineral commodities accounting for 92 percent of land use are, in decreasing order, bituminous coal, sand and gravel, stone, phosphate rock, clay, copper, and iron ore, all predominately surface mined. Bituminous coal production was responsible for nearly half of the total area utilized. Reclamation of mined lands and waste disposal sites over the reporting period was largely on lands utilized in mining bituminous coal; 75 percent of the land used for bituminous coal production was reclaimed.

Jan 1, 1981