Search Documents

By J. M. Provost

1. Estimates have been made for eight coal beds in Marion County, but only the Pittsburgh is important from a production standpoint at this time. The Pittsburgh bed has the largest recoverable reserve, and the Sewickley is second in importance. 2. Known measured and indicated reserves thickness of 14 inches and on 1,800 short tons estimated at 3,141 million tons, as of January lion tons is in beds 28 inches and more thick in all beds, based on a minimum per acre-foot of coal in place, are 1, 1955. Of this total, 2,983 mil-Areas in each bed were omitted from the estimate because available data relative to the bed characteristics were too meager for making an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1956

By Steven R. Munts

In 1985, at the request of the U.S. Bureau of Land Management, the U.S. Bureau of Mines studied 39,420 acres of the 60,960-acre Skedaddle Wilderness Study Area in order to evaluate its identified mineral resources. There are no known mines or mining operations in the study area. None of the prospects or claims in or within a 1 mile peripheral zone around the study area have recorded production. At least 276 recorded lode, 6 unrecorded lode, and 29 placer claims have been located in and within about 1 mile of the study area. Approximately 191 of the claims are in the study area. Four of these were current in 1985; all four are wholly or partly inside the study area. None of the study area was being explored by private industry in 1985. Metallic and nonmetallic commodities present in the study area consist of gold, mercury, perlite, basalt, pozzolan, stone, and sand and gravel. Perlite is represented by a single deposit which contains 184,000 tons of subeconomic resources in and adjacent to the study area. No other sites contained identified resources. There are no other identified nonmetallic resources in the study area. Occurrences in and near the study area contain small amounts of gold and mercury in vein-type deposits and show characteristics similar to bulk-tonnage, low-grade gold deposits. No base-metal resources were identified. The gold and mercury mineralization and perlite deposit are spatially related to a volcanic center located in the Skedaddle Mountains. Prospects in the Skedaddle Mountains may contain both precious metals and perlite resources, but additional work is required to adequately delineate these areas.

Jan 1, 1987

By Deno M. Pappas

The purpose of this Bureau of Mines study of U.S. roof and rib (roof- rib) accident statistics and related accident costs is to define current accident trends (1980-84) associated with fatal and nonfatal roof-rib fall accidents. Data were retrieved from a data base containing all recorded U.S. mining accidents, then sorted and normalized utilizing a computer software program. The statistics indicate that roof-rib accidents have significantly declined in the 5-yr study period. Moreover, they indicate that there have been increases and/or patterns of roof-rib accidents associated with specific mine characteristics, such as seam height, mine size, geographic location, and seasonal variations. Also, roof-rib injury characteristics produced pattern changes involving worker activity, lost workdays, types of injury, and severity of injury. A conservative estimate indicates that there has been a 30% adjusted increase in the cost of a roof-rib accident over the 5-yr study period.

Jan 1, 1987

By Forrest T. Moyer

Injury experience in the mineral mining and processing industries during 1968 was slightly improved in the nonfatal-injury record but worse in the fatality record. The resulting frequency rate of all injuries was slightly better, whereas the injury-severity rate retrogressed appreciably from the figure for 1967. Overall operating activity, as measured by man-hours of worktime, was slightly higher in 1968. However, there were several major segments of the mineral industries in which activity was lower owing to reduced demand for mineral products and to several major work stoppages. These statistics comprise the injury and work experience of all personnel engaged in production, exploration, development, maintenance, repair, and force-account construction work, including supervisory and technical personnel, and working partners and owners at mineral-producing and mineral-processing establishments in the United States. Data concerning officeworkers are excluded except for the oil and gas industry for which such information is not separable. All injury rates and totals are calculated from data before rounding. The data for 1968 are preliminary except for the anthracite, coke, petroleum and natural gas, native asphalt, peat, and slag industries, which are final. The figures represent full coverage for all industries except oil and gas for which coverage is not complete, particularly with respect to small companies.

Jan 1, 1970

By Steven J. Page

The increasing concern for dust control in metal and nonmetal mining prompted the Bureau of Mines to investigate the dust suppression technique of applying foam to face drilling and crushing operations in a gypsum mine. Previous attempts to achieve effective dust control on face drills using other techniques, such as dry collection and boom-mounted external water sprays, have not been successful. The largest problem encountered when using these techniques has been the lack of sustained effective dust capture at the face. Results for two faces studied show that injection of the foam through the drill steel provided an average dust reduction of 95 pct. However, the use of foam on the crusher provided no dust reduction at the operator's position (because of good local ventilation) and a 27-pct average dust reduction for two feeders at a location midway between the operator's position and the crusher. The conclusions obtained from this study are that (1) foam can be an extremely effective dust control technique when used on localized dust sources such as dust generated within a blasthole during drilling, and (2) foam is only marginally effective as a dust control technique when used on nonlocalized dust sources such as dust generated during the feeder-and-crusher operation.

Jan 1, 1981

By J. J. Dowd

1. The Pittsburgh bed is the most important bed in Ohio County, and virtually the entire production of coal in the county comes from this bed. 2. Known measured and indicated reserves in all beds, based on a minimum thickness of 14 inches and 1,800 tons per acre-foot of-coal in place, are estimated at 365 million short tons as of January 1, 1954. Of this total, 356 million short tons is in beds 28 inches and more thick. Areas in each bed were omitted from the estimate because available data relative to the bed characteristics are too meager to make an estimate that conforms with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves.

Jan 1, 1955

By R. L. Solmer

During 1959-61, the Bureau of Mines investigated the strain and deformation induced in rock and concrete linings around mine openings by retreat panel caving at the Climax Molybdenum mine. Two concrete-lined slusher drifts on the Phillipson level of the mine were instrumented with both electrical strain gages and extensometers. Changes in strain and deformation were recorded over an 18-month period during the undercutting and caving of the mining panel. General agreement was found between the strain and deformation measurements and the hypothesis that the vertical component of the stress field on the openings is almost completely removed by undercutting. This phenomenon is a possible explanation for the structural failures that occur in the slusher drifts during the undercutting cycle.

Jan 1, 1965

By E. D. Gardner, Edmund Stein

"IntroductionMassive sulphides occurring in metal mines are inflammable and furnish the fuel for many mine fires. Actual sampling has shown that dangerous amounts of sulphur dioxide and hydrogen sulphide may occur in mine atmospheres after blasting in massive sulphides. Probably some .of the finer sulphide in the material being blasted burns while it is in contact with the flame from the explosion. It’s also possible that oxygen of the explosive enters into the reaction.That sulphide dusts are explosive under some conditions has long been suspected, but the theory has not been generally accepted as having been proved. Evidence now at hand appears to be conclusive that such explosions do occasionally occur in mine workings in massive sulphides. Information from several mines working in heavy sulphides shows that occasionally, sulphur dioxide in larger amounts than could be expected from the blasting alone are occasionally thrown out into the mine atmosphere during blasting. Accidents have occurred and lives have been lost by men being caught in such gases. Also it appears in a few cases that damage done to timber in stopes by concussions has been greater than could 112.ve been expected from the regular blasts. In most of these cases the unusually large amounts of Sulphur dioxide could only be accounted for by an explosion or by an ignition of sulphide dusts. When this occurs it is probable that the settled dust is stirred up by the first shot of a round, then the dust cloud is ignited by this or a succeeding shot.In one instance, the senior author, while wearing breathing apparatus, returned to a station to take a gas sample immediately after a raise round had been blasted, and encountered a heavy white fume or smoke that was corrosive to the skin and which forced a retreat. The sample, which was taken farther back in a greatly diluted atmosphere, showed a high percentage (0.18) of sulphur dioxide. The station and the raise which was just being started were very dry and the walls and floor of the station contained settled sulphide dust which apparently was ignited by the blast."

Mar 1, 1928

By G. R. Hopkins

One of the largest items in the expense of operating a refinery is the cost of the fuel used in distillation and for miscellaneous purposes such as in the heating of buildings and in the generation of electricity, On a B. t. u. basis, the average refinery consumes approximately one-tenth as much fuel as it produces. Theoretically, the fuel consumption at refineries should be much smaller than this, but furnaces can riot be designed to be 100 per cent efficient' and, in addition, a large part of the waste heat is low-temperature heat which would not pay for the expense of recovering it. Annual surveys of fuel consumption at refineries have been made by the United States Bureau of Mines, beginning with 1925. During the 5-year period, 1925-1929, the refineries made steady progress in fuel economy. This is evidenced by the Computed figures of heat requirement Per barrel of crude oil refined, which show a decline from 829,000 B. t. u. in 1925 to 639,000 B. t. u. in 1929 (see fig. 1). In 1930, however, the trend in fuel economy was reversed and the quantity of heat utilized in refining the average barrel of crude oil rose to 672,000 B. t. u. There were undoubtedly a number of reasons for the apparent decrease in fuel economy at refineries in 1930, chief of which were the tendency to carry the distillation farther instead of merely topping the crude and a gain in the consumption of waste oils, such as acid sludge, which in actual practice yield less heat per unit consumed than has been theoretically assigned to oil. The consumption of natural as fuel at refineries has declined since 1927, but this has been more than compensated by a rapid increase in the use of refinery or still gas. The total consumption of oil as refinery fuel in 1930 was not much below the 1925 total, but the consumption of coal has declined rapidly, so that in 1930 liquid and solid fuels contributed only 56 per cent of the total heat units- utilized at refineries as compared with 77 per cent in 1925 (see fig. 2).

Jan 1, 1931

By Joseph D. Davis

Selection of a suitable coal or coals for the manufacture of coke of desired quality with due consideration of the purpose for which the coke is intended requires careful thought, and often it will pay to go to considerable expense in testing such coals as may be available. In general it will

Jan 1, 1942

By J. F. Barkley

The work covered in this report was done to meet the requests from many Government agencies for information on alleviating sludge difficulties in No. 6 (Bunker C) fuel-oil storage tanks. Accumulated sludge at times caused serious loss in tank capacities; pumps became overloaded or lost suction; strainers often required very frequent cleaning; fuel-oil heaters in some instances became fouled and inefficient; and gobs of sludge that passed the strainers interfered with good combustion. The requests also included questions regarding the usefulness in general of oil "additives" for preventing sludge and the relative merits of the many trade-named additives being marketed. Realizing that preventing such difficulties would result in substantial savings to the Government, an investigation was begun with the limited funds avail-able. Although various claims are made for No. 6 fuel-oil additives other than preventing sludge, only an investigation as regards the storage tank-sludge problem has been possible.

Jan 1, 1955

By Edward Thomas

"HISTORYThe origin of roof bolting as a means of roof support is obscure. During the past 23 years a method was developed by the. St. Joseph Lead Co: at its mines in southeastern Missouri, ranging from occasional use of single bolts with small bearing plates to systematic networks of bolts utilizing continuous bearing plates. Officials of this company are not certain which of its employees suggested their use. Many instances of occasional use of roof bolts have come to light during the past few years in widely separated mining districts, such as in West Virginia, Alabama, Illinois, Colorado, and Wyoming bituminous coal mines, and in Pennsylvania anthracite, Lake Superior iron, and Colorado lead-zinc mines. A few of the known installations have boon in place as long as 40 years.These installations usually were made to supplement wooden timbering in mine openings whore space was constricted, although it had been reported that roof bolting was started as a systematic moans of roof support in at least three instances but was abandoned because the cost of installation was excessive. The extra expense above that of conventional timbering could not be recaptured through economies resulting from increased efficiency, such as would be gained through mechanized mining.Roof bolting was first mentioned in mining literature in an article by W. W. Weige 3/ in Engineering and Mining Journal of May 1943, in which he described the use of bolts with 4-inch channel bearing plates in mines of the St. Joseph Load Co."

Sep 1, 1950

By Jon A. Hummer, Emanuele Cauda, George H. Schnakenberg, Aleksandar D. Bugarski, Samuel J. Janisko, Larry D. Patts

A series of engine/dynamometer tests was conducted to assess the effects of three types of uncatalyzed diesel particulate filters (DPFs), a diesel oxidation catalytic converter (DOC) and three types of high temperature disposable filter elements (HT DFEs) on the concentrations and size distribution of diesel aerosols and concentration of nitric oxides in underground mine air. Tests were conducted in the NIOSH Diesel Laboratory at the Lake Lynn Laboratory experimental mine, a facility developed to allow evaluation of these and other control technologies directly in an underground environment. The aforementioned technologies are evaluated by comparing the aerosol and gas measurements in the mine air 60 m downstream of the exhaust from a naturally aspirated, mechanically controlled engine fitted with the tested systems or muffler and operated at four steady-state engine speed and power modes. The tested DPF and HT DFE systems caused a 10-fold reduction in total mass concentrations of aerosols. The size distribution and number concentration measurements showed that all tested DPF systems and HT DFE elements effectively removed accumulation mode aerosols (D50>30 nm) for all test modes. An increase in peak number concentrations of nucleation mode (D50>30 nm) diesel aerosols is evident for some of tested DPF systems when engine was operated at high-load modes. The effects of uncatalyzed DPFs on nitric oxide (NO) and nitrogen dioxide (NO2) concentrations are found to be minor. A four-fold increase in percentages of NO2 in total nitrogen oxides (NOx) over baseline case was observed for the DOC when the engine was operated at high-load modes. The findings from this study should contribute to better understanding the potential for various control technologies to reduce exposure of underground miners to nano and ultrafine aerosols. In addition, detailed physical characterization of diesel aerosols made directly in occupational setting should foster a better understanding of the health risks associated with exposure to nano and ultrafine diesel aerosols.

By R. L. Grayson, L. L. Probert

"A three-year project focusing on the depth profiling of respirable coal mine dust particles using scanning electron microscopy coupled with energy dispersive X-ray analysis resulted in the development of statistically classified particle-behavior models. The models depict the changing silicon fraction for particles at 5-, 7-, 9-, and 11-keV accelerating voltages, thereby giving a clear indication of the nature of various types of mineral particles. This paper focuses on the results for respirable quartz particles sampled from five underground coal mines across the US. Through statistical analysis of results the relationship between the fraction of surface available quartz in respirable dust samples and coal rank is established for three Pennsylvania coal seams. IntroductionThis is the last in a series of papers detailing the results of SEM/EDX-based analyses of respirable coal mine dust particles collected from field sampling. Previous papers have detailed preliminary results and the statistical validity of the methodology (Grayson, Andre, and Simonyi, 1990; Grayson, 1991). This paper presents the final results of the analysis of respirable dusts from five coal seams with a range of coal rank:• Lykens Valley seam (anthracite), eastern Pennsylvania• Brookville (A) seam (mid-vol bituminous), central Pennsylvania• Pittsburgh seam (high-vol B bituminous), western Pennsylvania• No. 6 seam (high-vol C bituminous), Illinois• Wadge seam (sub-bituminous A), ColoradoSEM/EDX-based techniques were applied to try to clarify the role of quartz as an etiologic agent in coal workers' pneumoconiosis (CWP). It was hypothesized that previous studies were hampered by the restrictions of bulk analysis techniques and that particle-level analyses were needed to answer a number of questions concerning the role of quartz in CWP and its progression.Since 1985, a large number of the respirable dust samples submitted to MSHA are analyzed for free silica (Tomb, Parobeck, and Gero, 1986). Our reasearch shows that conventional bulk analysis techniques may not give a true indication of the biologically available, or active, quartz in mine dusts. Analytical evidence indicates that respirable dust samples may contain many quartz particles that are occluded, or coated, resulting in a bulk analysis for ""free silica"" that may not be indicative of the biologically available quartz surface."

Dec 1, 1996

By C. A. Herbert

"The Bureau of Mines for a number of years has conducted experiments at its experimental mine near Bruceton, Pennsylvania, on the explosibility of coal dust, with particular reference to dust explosions in coal mines, and the knowledge so rained may well be applied to the handling of coal dust at industrial plants and elsewhere.Powdered coal is coming into use more and more as a fuel, and the dangers incident to its use should be recognized and guarded against, as a number of accidents have occurred in recent years due to ignorance of this danger or to carelessness.Within the past three years two very serious accidents, under almost identical circumstances, have occurred on the surface at two different coal mines in Southeastern Iowa, due in each case to the sudden ignition of a cloud of fine coal dust.The first accident resulted in the burning of six men, three of them fatally; the second burned eleven; three men died as a result of their burns.The mines in the Southeastern part of Iowa, where these two disasters occurred, are operating in a thin coal bed averaging about three feet in thickness, and are worked on the long-wall advancing system similar to that of Northern Illinois.The miners in this section are paid on a screened coal basis; in other words, receive no pay for the fine coal. As a result they use forks in loading the coal into the mine cars, and naturally a considerable quantity of coal is left along the roadways. Subsequently this fine coal, together with the roof rock that is taken down to give sufficient height on the roadways, is loaded into cars and dumped in piles on the surface. This roof rock is a block, oily shale and the contribution of fine coal and oil shale gives ample combustible material to thoroughly burn the rock as it is dumped."

Jul 1, 1923

By Florence L. Feicht, H. H. Schrenk, Carlton E. Brown

This report describes the dropping - mercury electrode , its use in analysis , and the procedure of the Health Division of the Bureau of Mines in determining lead , cadmium , and zinc . The dropping - mercury electrode or polarograph is an electrolytic device , one electrode of which consists of mercury issuing in small drops from a capillary tube . Such electrodes have been in existence for more than 50 years, but they were not used for analytical purposes until about 1922.6/ Developments since have been rapid , especially in Czechoslovakia , Germany , Italy, and Japan and more recently in the United States . A recent bibliography / contains references to, 825 articles issued from 1903 through 1940. In 1939 Kolthoff and Lingane presented the first comprehensive critical review, in English , of the device and its use in analysis . They have recently issued a book on the same subject. Similar information also is included in a recent book10/ by Kolthoff and Laitinen . Much of the information in this and the two following sections on this device and its use in analysis was obtained from these three publications . The use of the dropping - mercury electrode in analysis is based upon the fact that the kind and amount of electro - reducible and electro - oxidizable constituents in solution can be determined from the current -voltage relationships revealed by this electrode or electrolytic device .

May 1, 1942

By D. A. Reynolds

THIS PAPER gives results of an investigation of the composition and carbonizing properties of coals from the Beckley bed, Caretta No. 5 mine, Susanna, McDowell County, and Glen Rogers No. 2 mine, Glen Rogers, Wyoming County, W. Va. The investigation included BM-AGA carbonization tests at. 800° and 900° C. and various chemical and physical tests designed to evaluate agglutinating, plastic, and expanding properties of coal. Both coals were of low-volatile bituminous rank, and each was blended with 70 and 80 percent high-volatile A coal from the Pittsburgh bed, Warden mine, Allegheny County, Pa. The Beckley bed was 39 to 58 inches thick at three points in the Caretta No. 5 mine, and the coal was 39 to 49 inches thick. The carbonizing sample contained 83.0 percent fixed carbon on the dry, mineral-matter-free basis. It contained 3.1 percent moisture, 15.8 percent volatile matter, 72.4 percent fixed carbon, 0.7 percent sulfur, and 8.7 percent ash, as carbonized. The ash softened at 2,680° F. The free-swelling index was 7;i, and the agglutinating value was 7.7. This sample fused weakly in the Gieseler plastometer; its blends with 70 and 80 percent Pittsburgh coal attained maximum fluidities of 830 and 600 dial divisions per minute, respectively. The single coal yielded 83.0 percent coke at 900° C. Yields of other carbonization products per ton of coal at 900° C. were: Gas, 9,950 cubic feet; tar, 3.5 gallons; light oil, 1.36 gallons; and ammonium sulfate, 16.3 pounds. Blending with Pittsburgh coal lowered the yield of coke and raised the yields of other products significantly. Caretta coal yielded strong, blocky coke at 900° C., 89 percent of which was plus-2-inch size. Strength indexes of 900° C. coke from 30:70 blends of Caretta No. 5 and Pittsburgh and of Pocahontas No. 3 and Pittsburgh coals were, respectively: 2-inch shatter, 68 and 53; 1%-inch shatter, 90 and 85; 1-inch tumbler, 50 and 53; and %-inch tumbler, 62 and 65. The specific gravity of the 900° C. gas from Caretta No. 5 coal was 0.272, and the heating values were 491 B. t. u. per cubic foot and 2,440 B. t. u. per pound of coal. The blends yielded much richer gas. Yields of tar acids and bases (0.09 and 0.04 gallon per ton, respectively) were within the normal ranges for low-volatile coals. Caretta No. 5 coal expanded 7.5 percent in the sole-heated oven at a charge density of 55.5 pounds per cubic foot. The blends containing 70 and 80 percent Pittsburgh coal contracted 4.8 and 7.5 percent, respectively.

Jan 1, 1953

By David A. Monaghan, Kenneth R. Maser, Adi R. Gurdar, D. Randolph Berry

APPENDIX E EQUIPMENT USED FOR FIELD TESTING OF MINE SEALING SYSTEM I. Drilling Operation - Equipment supplied by local drilling contractor 1. Mobile drill rig. 2. Flat bed truck, containing 20 lengths of drill pipe. 3. Auxiliary compressor. 4. Pickup truck for small parts and supply of diesel fuel. 5. Bulldozer. 6. Water supply, in this case the nearby stream. 7. Supply of casing, positioned next to the drill rig. 8. Ready mixed cement grout. 9. Drill bits, stabilizer units, cutting and welding equipment, other miscellaneous tools and supplies. II. Sonar Probing Operation 1. 25 foot tower with pulley mounted atop. - FMA 2. Electric winch with 100 feet of 1/4-inch cable, Model No. 100A, City Engineering Co. , Indianapolis, Indiana. 3. 400 feet of 1-1/2-inch-diameter aluminum pipe with alignment holes and coupling grooves. - FMA*

Jan 1, 1973

By A. L. Murray, C. A. Allen

"In the Spring of 1919, the Industrial Commission of Utah undertook the assembling of safety orders covering metal mining operations Just at that time there appeared several articles in the mining papers advocating the licensing of hoisting engineers, so this subject was given careful consideration,The licensing of hoisting engineers means that they must pass an examination covering the mechanical features of hoists and boilers, and must have a certain amount of experience. This undoubtedly serves to get a class of hoisting engineers that are better informed about the mechanical operation and theoretical considerations in hoisting and the only room for argument against it is that it is difficult to give an examination that will determine whether or not a man is a competent hoisting engineer.A man might pass an excellent examination yet be absolutely unqualified to operate a hoist and the judgment of the mine super- intelligent would have to be depended upon to choose the right man from among those who were licensed. This difficulty of properly determining, by ordinary examination, a man's qualifications to run a hoist caused the idea of licensing' in the ordinary sense of the word to be abandoned; but, as there was no question that a hoisting engineer should be physically fit, it was decided to require a medical examination, and at the same time to require the hoist engineer to state his experience, so the State would better knowledge of his general qualifications.The orders covering the question were therefore issued as follows;"

Jan 1, 1920

By R. Pakalnis, Richard P. Curtin, Lewis A. Martin

Instrumented cable bolts developed at the Spokane Research Laboratory of the National Institute for Occupational Safety and Health were used in conjunction with existing ground control to monitor rock mass loads at various field sites (FMC Granger, Getchell, Meikle, SSX, K-2, and Stillwater). Axial and shear loads were determined by strain gauges to levels of instrument accuracy of ±5 N or ±5 microstrain as these loads were transferred to the instrumented cable bolts. These gauges were 12.5 mm long and embedded into are manufactured king wire that replaced the conventional king wire. Cable bolt performance, quality of grout, and installation techniques were also assessed. By using instrumented cables, a mine operator can determine axial load along the cable at predefined gauge locations. By monitoring load on and displacement of the rock mass, more effective ground support can be selected and installed, which will lead to safer working conditions for miners.