Search Documents

By Jianmin Qin, Raja V. Ramani, Wilson Miola

"The number of underground work entities operating under reduced dust standards in U.S. coal mines has been increasing since the start of the decade of the 80s and is currently approaching 10,000. The concern for controlling the quartz levels in airborne respirable dust in coal mine has manifested itself in several improvements in equipment selection and operation, face ventilation practices, and dust control procedures. At the same time, fundamental studies have been initiated on determining the source-sink relationships of the airborne quartz dust. The P-7 method is the prescribed method for the determination of quartz in the respirable airborne dust samples from coal mines. Questions have been raised on the reliability of the P-7 infrared spectrometry method for quartz analysis in powders. No specific method has been defined for quartz determination in bulk samples from the mine.In a recent study on the relationship between quartz in the airborne dust and that in the materials being mined, both infrared (IR) and x-ray diffraction (XRD) methods were used on a suite of samples from several coal mines. These samples encompassed airborne respirable dust samples, airborne total dust samples, the oversize fraction from the respirable samplers, ROM samples, channel samples, and chip samples from the face, roof, and floor materials. In this paper, the sample preparation and analysis procedures for the samples are discussed. The data, analysis results, and comparisons of the P-7 and XRD results are presented. The quartz percent determined for the same sample by the two methods are different. In 85% of the samples analyzed, the quartz percents determined by the XRD method are higher than those obtained by the P-7 method. However, there is a strong linear relationship between the results from the two methods. Further, the XRD method indicates an average of 20 percent more quartz than that from the P-7 method. The reasons for the differences in the results and the need for additional studies are explored.Since the enactment of the Federal Coal Mine Health and Safety Act of 1969 and the Federal Occupational Safety and Health Act of 1970, the prevalence of free silica as an occupational hazard in dusty work environments has been a matter of increasing concern. In underground coal mining, sometimes, roof, floor, clay veins and other non-coaly material must also be mined along with the coal. Mining these materials may increase the amount of quartz in the airborne dust (Pimentel and Adam, 1985; Taylor et al., 1984; Colinet et al., 1985). The problem of high quartz levels in the respirable airborne dust is widespread in continuous miner sections. In addition to the need for controlling the silica amount in mine atmosphere, a need for a sensitive, easily performed method for the determination of free silica in airborne dust samples was also recognized."

Mar 1, 1992

By R. R. Faddick

Properties of coal-water slurries were studied in two separate phases: a rheological phase and a pipeline phase. The purpose of the study was to investigate the rheology of fine coal slurries to determine the effect of fine particles in a coal-water mixture on the economic and operational aspects of a slurry pipeline. The slurries consisted of 6x10, 100x200, and 200x0 mesh coal in water. A fourth slurry consisted of a mixture of the 6x10 and 200x0 mesh coal. Brookfield and Stormer rotational viscometers were used to obtain or simulate rheograms for a range of fine coal concentrations, temperatures, and particle sizes. All the slurries were pumped through a 1-inch diameter acrylic pipe. The fine coal slurries were found to encompass four distinct rheological models. The narrow size distribution of the coal slurries was apparently responsible for the high pipewall friction losses, more so than the particle size. A scale-up method applicable to Bingham plastics was found satisfactory for predicting pipeline headlosses of fine coal slurries from rheology data.

Jan 1, 1974

By E. M. Tignor

As a part of the program of promoting the conservation and efficient utilization of petroleum, studies are being made by engineers of the Bureau of Mines on secondary oil-recovery projects throughout the United States. In furthering that aim, engineering data concerning the reservoirs, methods of stimulating the production of oil, and other pertinent facts are collected, studied, and subsequently published so that others may profit by the experience gained. This report presents the results of a study made by engineers of the Franklin, Pa., office of the Bureau of Mines of secondary oil-recovery operations in the Boggs field, Spencer district, Roane County, W. Va., whore natural gas is injected into the reservoir to stimulate the production of oil from a so-called stripper field. The Boggs field, like most others in the Appalachian region, is one in which the major part of the natural energy that caused oil to flow through the reservoir to the producing wells during the primary stage of oil production has been dissipated. For all practical purposes, most of the oil produced in the Appalachian region at the present time can be considered to be from stripper fields. Consequently, secondary recovery methods are being used extensively in the oil-producing areas of New York, Pennsylvania, West Virginia, Ohio, and Kentucky for recovering some of the oil that was not produced by primary production methods.

Jan 1, 1949

By A. B. Hooker

All state mining laws require that flame safety lamps be used in gassy mines; the laws of some States require that safety lamps be kept for emergencies at every coal mine, whether gassy or nongassy. The use of the flame safety lamp has been widespread because it is the only defice readily available for detecting both the presence of methane and deficiency of oxygen. This paper reports the results of an investigation by the Electrical Section, in cooperation with the Gas Section, of the Pittsburgh Experiment station relative to the behavior of permissible flame Safety lamps in mine atmospheres deficient in oxygen and the effects of methan5/ on the detection of oxygen deficiency.

Jan 1, 1937

By Carla A. Kertis, Alan A. Campoli, Claude A. Goode

This Bureau of Mines study was conducted to obtain a better understanding of the coal mine bump problem and its effect on underground coal mining in the Eastern United States. To accomplish this, information was collected on the geologic conditions, mining techniques, and engineering parameters at five bump-prone mines. Two geologic conditions have been found to cause the occurrence of bumps in the Eastern United States: (1) relatively thick overburden and (2) extremely rigid strata occurring immediately above and below the mine coalbed. Additionally, the probability of bump occurrence is increased by certain mining practices that concentrate stresses during retreat mining, in areas where geologic conditions are conducive to bumps. Mining plans that permit the development of pillar line points or long roof spans that project over gob areas should be avoided because these features may contribute to the occurrence of bumps.

Jan 1, 1987

By Oliver Bowles

"A New Mica Company in China A report has been received from the American Consulate at Chungking, China, to the affect that a new company has been organized to operate a mica mine north of Ta-chien-lu, in the province of Ssu-Chuan. The company, which is entirely under Chinese management and control, has a working capital of $10,000. While comparatively new, the mine has been worked before, and apparently with some success. The mica is said to be of good quality. It is claimed that the deposit will supply a limited amount of mica that will cut in pieces a foot square or over, and larger quantities of smaller sizes. The chief difficulty is transportation, for it is reported that a ten days' journey, part of it over mountain trails, will be necessary to transport the mica from the mine to Yachow, the nearest practical waterway. It is probable, therefore, that the output of the mine will be limited.Necessity for Careful Trimming and Grading of MicaA recent report to the Department of Trade and Commerce, Ottawa, Canada, by Acting Trade Commissioner C. G. Venus, London, England, contains information which is of vital interest to mica producers in the United States. It is pointed out that mica exports from Canada to England show a gradual decline dur¬ing recent years, the figures being as follows: 1913- 1,383 cwt: 1914 - 1,225 cwt: 1915 - 1,864 cwt: 1S16 - 879 cwt: 1917 444 cwt: 1918 - 480 cwt. Shipments from India to England, on the other hand, show a steady increase from 40,178 cwt. in 1913 to 66,401 cwt, in 1918."

Jan 1, 1920

By John D. Spencer

Surveys to establish the quantity and quality of coals available for metallurgical, industrial, and energy use, investigations to develop better mining methods, and studies aimed at improving the health and safety of those who mine the coal highlighted Bureau of Mines research and technologic work on coal in 1968. Also being developed are more efficient methods of coal preparation, transportation, storage, and utilization. Supplementing this effort are projects designed to assure minimum disturbance of land, water, and air resources. Research centers and laboratories of the Bureau of Mines are listed in appendix A. Publications released during 1968 are cited with the various projects and in appendix C. Organizations that cooperated in the work in various ways are cited in appendix B.

Jan 1, 1969

By John R. Rhodes

The objective of this project was to investigate the feasibility of analytical techniques potentially capable of determination of Mg, Al, Si, S, Ca and Fe in 1 to 2 mg samples of respirable coal mine dust, in a total analysis time of not more than 10 minutes per sample, using equipment capable of being truck mounted for field-laboratory operation. It was not essential that the technique be non-destructive, but the chosen technique is, and this enables the analysis to be performed directly on the 37 mm diameter membrane filter on which the respirable dust sample is normally collected. The sensitivity requirements are therefore quoted in terms of the units of measurement, µg/cm2. The detection limit (3o of the background criterion) should be 0.5 µg/cm2 or less. The precision should be 5% or better, at concentrations above which the detection limit is not the determining factor.

Jan 1, 1972

By Loren R. Anderson

Traditionally, an evaluation of the safety of slopes has been based on computing a safety factor against failure. In computing the safety factor, the geometry of the slope, the soil parameters and the pore pressures are treated as deterministic quantities even though they are known to be random variables. A pseudo-three-dimensional probabilistic slope stability model has been developed that treats shear strength as a random variable. The model uses the probability of a slope failure as an assessment of slope reliability. The model can accommodate zoned embankments of soil in which the strength is described by the Mohr-Coulomb strength envelope. Autocorrelation functions are used to describe the spatial correlation of the strength parameters, c and tan ø. Model error can also be included in the analysis. The model has been applied to an existing tailings dam and to several hypothetical examples. These examples are presented to illustrate the influence of the choice of the soil strength variability parameters on the probability of failure. The results show that the critical failure surface based on the minimum safety factor is not necessarily the failure surface that will yield the maximum probability of failure. The analysis of the tailings dam shows that variance reduction can be large and that the model error is the dominant source of uncertainty for the embankment analyzed.

Jan 1, 1982

1.0 Control House (DWG. NO. 56-401-G) - 1.1 Physical Description The Control House is a single story, 2728 square foot building with an adjacent transformer yard. A four foot overhang provides shade protection for the walls. The building is heated and air conditioned. The HVAC System has an elevated outside air intake and provides a positive pressure environment within the structure in order to prevent the infiltration of heavier-than-air, noxious gases. The materials of construction are as follows: Structure : Light-Gage Metal Framing Exterior Walls :Outside - Preformed, Metal Siding :Inside - Insulated Metal Liner Panels Interior Partitions :Gypsum Board over Light-Gage Metal Framing Roof :Insulated, Preformed Metal Panels Ceilings :Mechanical & Electrical Rooms - Exposed underside of Roof Panels Control Room, Lunch Room, Toilets, Entry - Suspended Acoustical Lay-In Tile Floors :Mechanical & Electrical Rooms - Concrete Slab on Grade Control Room, Lunch Room, Toilets, Entry - Resilient Tile Exterior Doorsand Windows :Preformed Metal Panel Manufacturer's Standard Units

Jan 1, 1979

By Robert P. Bruno

This report covers the study of the feasibility of using a hand-held infrared viewer as a methane indicator to observe methane gas at the face of an underground coal mine. The objective of this program was the development of a hand-held device to remotely detect the presence of concentrations of methane gas in underground coal mines. Convenient "mapping" of methane from a remote location would allow rapid and safe corrective procedures for working personnel. Modified commercially available equipment was evaluated both in the laboratory and in a working mine. Although readings were obtained and the general principle of operation demonstrated, the power levels necessary, and protective enclosures required, would raise the weight of the instrument beyond practical limits of portability. Based on currently available technology, it is the conclusion of the investigations that a practical, portable, hand-held visual methane indicator is beyond the state-of-the-art. The recommendation was, therefore, made that work be suspended, and the results and data compiled and presented in a final program report.

Jan 1, 1979

By Frank G. Miller

Controlling natural-water drives to effect efficient and economic production of petroleum, through wells, from reservoir sands and rocks is a problem of major importance in the oil-producing industry. Water-drive fields are characterized by large quantities of mobile water under high pressure immediately below the oil in the flanks or extraneous parts of reservoir formations, Hence, the water, which is in fluid connection with the oil and a source of a large proportion of the energy available for moving it, advances up-structure to replace it. This phenomenon of water moving crestward into the oil-bearing parts of the reservoir and replacing oil is termed edgewater encroachment. The mechanism by which oil is flushed out and continually replaced by water as the hydocarbon content of the field is depleted must be understood if natural-water drives arc to be used successfully to, induce efficient recovery of oil from its reservoir rocks. Until recently, the function of water in the production of oil has been somewhat obscure and was not given the consideration it deserved in early petroleum production-research programs because of the greater importance associated with and the effort devoted to investigations concerning the relations of natural gas to production of oil. Thus, with virtually no fundamental information at hand, it is not surprising that at first edgewater was considered a necessary evil, and the manner in which it was dealt with depended largely on the experience of the operators. During the intervening years, however, practical information on encroachment of edgewater in oil sands has been widely disseminated as a result of studies of oil-field depletion, and many theories pertaining to petroleum-reservoir energy and performance have been advanced; these theories necessarily included consideration of edgewater as an integral -art of the reservoir fluids and a source of energy for propelling hydrocarbon fluids through the reservoir and to the surface of the ground.

Jan 1, 1941

By G. L. Oldright

The data presented in this paper were collected et the smelter of the Consolidated Mining A Smelting Co. of Canada, Limited, Trail (Tadanac), British Columbia, through the courtesy of S. G. Blaylock, vice president and general manager; James Buchanan, smelter superintendent, George Murray, assistant smelter superintendent; and the staff members listed in Paper XI, Report of Investigations 3243. INTRODUCTION This paper is the twelfth of a series on smelting in the lead blast furnace and the fifth4 dealing with blast-furnace gases.

Jan 1, 1934

By P. L. Loyselle, B. D. Comilsen, D. H. Carlson, J. H. Johnson

"In-mine airborne particulate samples have been successfully collected and the relative amounts of diesel and coal determined using the Laser Raman Quantitative Analysis (LRQA) method. This method allows analysis of filters which have been collected by a method similar to that used to determine the airborne respirable dust concentration in us underground coal mines. Samples were taken near the feeder-breaker, on haulage vehicles, and in the returns. Sampling methodologies were developed for coal-only and diesel-only particulate reference samples with sufficient filter loading for the LRQA method. A statistical analysis of reproducibility has been carried out. Samples have been collected simultaneously at two locations using the LRQA and the size-selective sampling methods. Good agreement between the two methods has been found.INTRODUCTIONThe goal of this research has been to develop the Laser Raman Quantitative Analysis (LRQA) method to measure the composition of respirable particulate, i.e. the fractions of coal and of diesel particulate, in the mine ambient air. In earlier Bureau of Mines sponsored research, we successfully demonstrated that the LRQA method could be used to measure the fraction of Diesel Particulate Matter (DPM) in coal/diesel particulate mixtures which were prepared in the laboratory.(I) 'The immediate objective was to test and refine this LRQA method on samples collected in a diesel underground coal mine.Specific objectives required to meet this goal include:I) Develop in-mine sample collection methods which will insure sufficient particulate loading on filters for LRQA. ,2) Develop methodology for in-mine collection of reference samples (""coal-only"" and ""diesel-only"" filters) which arc required for quantitative LRQA. 3) Analyze precision and accuracy of the LRQA method. 4) Compare composition measurements with another analytical method, i.e. the University of Minnesota/Bureau of Mines size selective sampling Micro-Orifice Uniform Deposit Impactor (MOUDI) method.An advantage of the LRQA method is that it allows analysis of filters which have been collected by a method similar to that used to determine the respirable dust concentration in US underground coal mines. No new sampling instruments and techniques are required. Transfer of sample from collection substrate to analysis substrate is not necessary. Furthermore, other analyses can be made on the same sample since the technique is nondestructive."

Jan 1, 1988

By W. A. Calhoun

A method for concentration of the nickel-cobalt-bearing mineral, siegenite, from a table middling has been developed by the Bureau of Mines at Rolla, Mo. The table middling is composed of a complex series of sulfide minerals, occurring in mill operations in the southeast Missouri "lead belt." In these operations the siegenite is lost as a separate concentrate, being diverted to other products. The procedure also includes recovering commercial-grade concentrates of copper and lead. A low-grade zinc concentrate, a potential coproduct, was also made.

Jan 1, 1962

By Rudolf E. Greuer

The existing computer programs for the simulation of ventilation systems under normal ventilation conditions are reviewed and a suitable program for including the influence of mine fires is selected. New program parts are written for the consideration of methane productions in coal mines, heat and gas productions of mine fires, temperature and air composition changes in ventilation systems, and the ventilation forces resulting from the latter. Other program parts are provided for the detection of danger zones and reversed air currents and for the inclusion of recirculated air currents in the network analysis. Existing program and new program parts are combined. The resulting new program can be used for a multitude of assignments. It is designed for the practical ventilation engineer and should be applicable to all types of ventilation emergency plans, in particular mine fire plans. The organization of the program and its mathematical basis are described. A FORTRAN IV listing and several flow diagrams are included. Eight executed examples are discussed, input and output for these examples explained. Storage requirements and execution times are estimated.

Jan 1, 2011

By George T. Motock

The author prepared the following report as the result of a trip to Germany in the summer of 1945 for the Technical Industrial Intelligence Commitee Subcommittee on Metals and Minerals. The purpose of this committee, which functions under the Joint Intelligence Committee of the Joint Chiefs of Staff of the United States Armed Forces and of which the Bureau of Mines

Jan 1, 1946

By Martin H. Rogoff

This publication combines a critical review of the literature on the microbiology of coal with an introduction to those areas of microbiology related to studies of coal as a biological material. The attack on coal by microorganisms as yet remains doubtful. Only the low-rank coals contain an indigenous microbial flora, and even these organisms are not peculiar to coal, but are common soil and water forms. No experimental data have as yet been presented, either in the literature or in the present work, which unequivocally demonstrate the oxidation of coal by microorganisms. Reasons for the resistance of coal to such attack, including insolubility, physicochemical structure, steric hindrance of enzyme action, and the presence of antibiotic materials in coal are discussed. Microorganisms do attack large aromatic molecules and the mode of oxidation of aromatic ring systems by bacteria is presented. Well-defined pathways are known for the oxidation of polycyclic compounds with one to three rings, and these paths with their key intermediates are described and related to the possible oxidation of coal.

Jan 1, 1962

By Irving Hartmann, Edward Thomas

"INTRODUCTION Adoption of rubber-tire shuttle cars underground in conjunction with mobile coal-loading machines has introduced new problems in the control of dust on mine roadways. Where this type of loading and transportation is used, development and extraction are generally rapid, with the result that much coal is spilled from the shuttle cars during normal operation, Coal in the roadways from this source and from sloughing of the ribs is ground to fine dust by the wheels of the 'shuttle cars and by the treads of the loading and mining machines. The coal dust usually is somewhat contaminated by pulverized rock, and the mixture could not be loaded with the run-of-mine coal without undue contamination of the product even if it were cleaned up promptly.The presence of large quantities of fine, loose dust, which is constantly stirred up and kept in suspension in air by the traffic, constitutes a grave explosion hazard, reduces visibility along the roadways, and is physiologically harmful to the workmen who breathe the air. From the operating standpoint the loose material is undesirable along the roadways because it provides poor traction for the trucks and thereby increases wear and power consumption. The dust-explosion hazard could be eliminated or reduced by frequent application of sufficient rock dust on the roadbed; but this would not remedy the other difficulties, and in fact it might intensify them. Where practicable, the most direct and effective safety measure is to clean up and remove promptly all dust that forms and settles on the roadways. Unfortunately, in many cases this procedure is not feasible. A third Suggested remedy is to prevent dispersal of the dust into the air and to promote its consolidation on the floor by wetting the dust particles.During the past few years several mines have used calcium chloride on shuttle-car roadways to allay the dust thereon. When exposed to the' humid atmosphere of the mine this salt absorbs Moisture from the air and deliquesces, and in this way wets the dust on the floor of the roadway. In a survey conducted in coal mines in southern West Virginia and in eastern Kentucky where calcium chloride has been in use, somewhat conflicting re- ports were received regarding the merits of the application, and several operators have abandoned the practice either because of actual or assumed disadvantages. The purpose of the study described in this report was to collect and correlate evidence and, on the basis of experimental data obtained in the field and in laboratory tests, to present a clearer picture of the factors involved in the allaying of dust by use of salts."

Sep 1, 1945

By C. E. Hennig

On January 1, 1959, the United States had 313 petroleum refineries with a total installed crude-oil throughput capacity of 9,819,846 barrels per day, according to the Bureau of Mines annual survey. Compared with a year ago, this represents a net decreased of five in the number of slants mild a net increase in capacity of 412,139 barrels per day. The continued increase in total capacity and decrease in number of plants raised the average capacity of a refinery to a new high of 31,373 barrels per day. During 1958 total capacity increased in every refining district except the Louisiana Gulf district, which showed a 2-percent decrease due mainly to the retirement of the American Oil Company's plant at Destrehan, La. The largest increase, 14 percent, occurred in the Texas Inland district followed by a 12-percent increase in the Arkansas-Louisiana Inland district. At the beginning of 1959 the industry was building facilities that would add 108,400 barrels per day to crude-oil capacity. It also had under construction a capacity of 226,100 barrels per day as replacement. On January 1, 1959, no new refineries were under construction.

Jan 1, 1959