Search Documents

The principle activities of the Explosives Research Laboratory from July 1, 1961 to June 30, 1962, are described briefly in part 1. Part 2 gives short abstracts of publications that appeared during fiscal year 1962; in general, the research reported in these publications antedates the report period. Part 3 gives the results of an investigation which, although too limited to warrant separate publication, merits presentation in some detail because of current interest in ammonium nitrate-fuel oil compositions.

Jan 1, 1964

By R. E. Hershey

1. Reserves were estimated for three coal beds: Lantana, Sewanee, and Richland. 2. Known measured and indicated reserves for all beds, based on a minimum thickness of 14 inches and on 1,800 tons per acre-foot of coal in place, are estimated at 34 million short tons as of Januray 1, 1954. Of this total, 15 million short tons represents coal 28 inches and more thick. Areas in the beds were omitted from the estimate because available data relative to the bed characteristics were insufficient to permit making an estimate conforming with the definitions of measured and indicated coal adopted for this study. Should future drilling or development prove reserves in these areas, such reserves should be added to the total estimated reserves determined by this investigation.

Jan 1, 1956

By H. P. Greenwald

For some years past the Safety in Mines Research Board of Great Britain has been making an intensive search for. materials that would be more efficient than rock dust and that could replace it wholly or in part as a moans of preventing the prorogation of coal-dust explosions in mines5/ In the course of this work several rock ducts and numerous inorganic compounds were tested. The results place incombustible substances in two main groups; (1) Those whose effect in suppressing the combustion of coal dust is proportional to their capacity for absorbing heat, and (2) those that shoo much higher effectiveness than would be expected from their heat capacity. The first group includes several inorganic compounds and materials commonly ground for use as rock dust, such as shale, gypsum, and limestone. Outstanding examples of the second group are compounds of the halogens6/ with the alkali metals,7/ especially potasium and sodium8/. British investigators term those salts "inhibitors" because it is assumed that their presence has a hindering or inhibiting effect on one or more of the chemical reactions that together constitute combustion. In other words, the action of an inhibitor is postulated as chemical rather than physical; theoretically, the effect is to prevent liberation of energy instead of to absorb energy already liberated.

Jan 1, 1940

By R. S. Warfield

Following World War II, the rapid increase in both military and civilian activity in the area served by the Alaska Railroad stimulated interest in the availability of local sources of nonmetallic minerals that might be used for building materials. Except for abundant sand and gravel and some pumice, the construction industry of the area depended entirely on high-cost imports for building materials of mineral origin. Because continued rapid growth was anticipated, development and use of local sources of such materials was advocated by both military and civil authorities to reduce the high costs of con¬struction and bolster the unstable economy of the area. The U.S. Department of the Interior began a program On included examining the numerous deposits of nonmetallic minerals accessible to the Alaska Railroad to determine their possible use as raw materials for the construction industry. Preliminary field investigations were made by the Geological Survey. The more promising deposits were subsequently examined and sampled by Bureau of Mines engineers, and the samples were subjected to the laboratory tests necessary to indicate the chemical and physical characteristics of the raw materials or their products. Such field and laboratory investigations were conducted on clay, shale, argillite, limestone, gypsum, and pumice taken from various parts of the area. In initial phasees of the work, done irate 1948 through 1952, many of the deposits examined were suitable for proctoring building materials. Results of the work completed during that period have been published in a Bureau of Mines report3 giving general information and detailed data on more than 35 deposits that were investigated.

Jan 1, 1962

By Walter K. Utt

The process of drilling and bolting the roof is currently one of the most dangerous jobs in underground mining, resulting in about 1,000 accidents with injuries each year in the United States. To increase the safety of underground miners, researchers froth the Spokane Research Laboratory of- the National Institute for Occupational Safety and Health are applying neural network technology to rite classification of mine roof strata in terms of relative strength. In this project, the feasibility of using a monitoring system on a roof drill to assess the integrity of a mine roof and warn a roof drill operator when a weak layer is encountered is being studied. Using measurements taken while a layer is being drilled, one can convert the data to suitably scaled features and classify the strength of the layer with a neural network. The feasibility of using a drill monitoring system to estimate the strength of successive layers of rock was demonstrated in the laboratory.

By Daniel L. Ng

This Bureau of Mines report describes the results of scanning electron microscopic (SEM) studies of the combustion residues of carbonaceous dust particles resulting from explosions and thermal ignitions in laboratory and full-scale mine tests. The dusts studied varied widely in rank and volatility: Pittsburgh seam bituminous coal (35% volatility), Pocahontas seam bituminous coal (16% volatility), anthracite (7% volatility), graphite, and diamond. The most systematic explosion studies were performed in an 8-L chamber with narrow size distributions of Pittsburgh coal dust with surface mean diameters of 2, 22, and 84 pm. Experiments were conducted mainly in air, with some data obtained in 50% 02. Observations of the bituminous coal explosion residues showed particles with rounded edges, particles with blowholes, and some cenospheres. The lower volatility dust residues showed fewer changes from the original, unburned dust. In addition to the experimental studies, results of SEM observations of residues from a mine explosion disaster are reported. Comparison of such residues with those from the laboratory and experimental mine explosions can help investigators determine the extent of dust participation in the disaster and in identifying the possible ignition sources.

Jan 1, 1983

By R. E. Head

At the microscopic laboratory of the Bureau of Mines Intermountain Experiment Station, Salt Lake City, Utah, efforts are being made to devise methods of differentially coloring finely crashed minerals as a means for their identification. Staining would facilitate sight recognition of minerals under the microscope and would be of great value in the study of crushed ores, concentrates, and tailings. Since the treatment of ores for their beneficiation is primarily based on the recovery of the minerals containing the clements of value, it is extremely important that these minerals should be known and that a method for quickly determining them when in minute fragments should be available. Herein lies one of the greatest uses for color methods. In many cases it is a difficult matter for even the trained petrographer and mineralogist to identify finely crushed minerals quickly. Although ordinary petrographic methods are accurate, they are often time--consuming and are not suitable to the needs of millmen who require, especially in the examination of tailings a method for determining minerals by inspection.

Jan 1, 1929

By Russell J. Miller

A high-pressure intensifier system was designed, constructed and field tested as part of a program to determining the feasibility of applying high-pressure water jets on conventional mechanical rock excavation equipment to increase advance rates. Also developed were a high-volume swivel, capable of transferring the high-pressure water to a rotating cutterhead and manifold system for locating and protecting the jets on the cutterhead. Field tests were conducted in a granite quarry near Skykomish, WA, approximately 90 miles east of Seattle. The concept of improving excavation rates by using water jets to assist mechanical cutting was proven to be successful, with an average increase in excavation mete of 50 to 60%. For some tests, the excavation rate was more than doubled. Machine torque requirements were reduced approximately 25% when the water jets were used. It was suggested this was due to reduced cutterhead friction in the presence of the water jets. A comprehensive economic analysis was undertaken as part of a concurrent study to determine the degree of cost benefits attainable from increased advance rates. Very significant savings were seen to be possible. It was concluded that the basic concept of combining a water jet capability with a mechanical excavating machine is definitely possible.

Jan 1, 1976

By J. W. Horne, W. L. Finley, A. D. Bauer, D. W. Gould

"The Bureau of Mines and the State of Colorado are cooperating in an investigation of the oil shales of Colorado. in this report the yields and the results of analyses of the oil and, gas produced from a number of oil-shale samples from the principal deposits of Colorado and other oil-shale States, are compared with samples from Scotland and Australia, where the oil-shale industry has had its greatest commercial development, and also with a sample from Brazil *here extensive oil-shale deposits are found shale samples were not selected as being representative of the different deposits, but they illustrate the wide variation in the nature of the organic matter of different oil shales.A further study is being made of the chemical composition of the shale, distribution of nitrogen and sulphur. in the products, temperatures at which organic matter decomposes, and the results will be presented in subsequent Papers, With complete data available on the chemical composition of the shales, it may be possible to explain some of the differences in the nature of the products from the various shales,Most of the work described herein was done under the supervision of M. J. Gavin. L. C. Karrick, formerly of .the Boulder laboratory, assisted in the work and gave many valuable suggestions."

May 1, 1924

By I. D. Schleicher, L. H. Rorden, F. B. Curry, T. C. Moore

The purpose of this program is to extend electromagnetic (EM) techniques for use in locating miners trapped in mines as deep as 1000 m. A previously developed EM system is considered adequate for use at mines less than 300 m deep where it has a probability of detection of 54%. A system for deep mines must keep underground equipment simple, and use extremely low frequencies (ELF), sensitive receivers, and noise cancellation. The proposed location method, developed by Develco for other applications, is based on vector field measurements from two or more static sensors and computation of source location by iterative techniques. During Phase II, very sensitive search coil sensors were built and used in a separate test to verify the feasibility of atmospheric noise cancellation. A "Breadboard" location system version without cancellation, which is a fieldable test bed to evaluate receiving and location functions, was tested and supplied. Very good results were achieved from the first in-mine test with the transmitter at a depth of 380 m. It is expected the results of this work, and additional evaluation tests in the future, will be used to define the requirements for a prototype operational system.

By C. A. Allen

"The problem of signaling to the hoisting engineer from a moving cage in the shaft has been considered by many mine operators for a number of years. There are several methods in use in different mining districts, and so far as the writer is aware they have been further developed in Utah than in any other state. The latest installations are of interest because they use a very low-voltage circuit for the shaft wires and also because the wiring can be so arranged that the hoist can be stopped from the cage, if so desired.The first installation in Utah was in the shaft of the Centennial-Eureka mine under the management of C. E. Allen. It was placed in operation in the summer of 1899, end has been in continuous and satisfactory operation for 21 years. The arrangement consists or two bare wires down the shaft carrying a current at 60 volts potential, with a device on the cage for making connection between the two wires. This device is simply a short piece of wire which is thoroughly insulated from the cage and is operated by a short lever. Whenever the cage rider wishes to signal the engineer he pulls down the lever, forcing the short wire out against the two bare wires, thus making a circuit which rings the bell in the hoist-room. A similar device was planned in the Grand Central shaft at Mammoth, Utah, but was later abandoned. The cause of failure was reported to be that the shaft was very wet."

Jun 1, 1920

By Donald E. Redmon

This Bureau of Mines report reviews injury experience in the nonmetallic mineral industries (except stone and coal) for 1966-67. For each of the years, 23 tables summarize disabling work injuries by department, source of injury, extent of disability, part of body injured, and nature of injury. Correlative information on employment, worktime, and operating activity is also presented.

Jan 1, 1973

By Stephen C. Tadolini, Thomas M. Barczak

An underground investigation was designed and implemented by the National Institute for Occupational Safety and Health (NIOSH) to evaluate the effectiveness of pre-driven longwall recovery rooms supported with pumpable concrete roof supports. The pumpable roof supports were instrumented with hydraulic pressure cells to measure support loading. Displacement of the support was also measured to assess the support reaction to ground movements. Movement up to 12.5 m (40 ft) into the roof was measured with sonic probes and multipoint extensometers. Borehole pressure cells were installed in the panel fender and outby pillars to evaluate load transfer. Shield loading was also assessed to determine the impact of the panel fender yielding on face loading. The results show that the yielding of the panel fender produced uncontrollable convergence that caused yielding of the shields and stiff pumpable roof supports when the face was approximately 3.12 m (10 ft) from the recovery room. The shields continued to yield until the face advanced into the recovery room. Convergence in the pre-driven recovery room typically reached 15-20 cm (6-8 inches) once the pumpable supports yielded and shed load through a declining residual load capacity prior to being cut out by the longwall shearer. Roof deformations occurred beyond the 10 m (32 ft) horizon with total deformation ranging from five to 10 cm (2 to 4 inches), indicating that standing support was necessary to help control the span as the longwall face advanced into the pre-driven recovery room. Stability improved as the pumpable supports were cut out, thereby reducing the span between the shields and the outby pillars. In the end, the shields were successfully recovered under stable ground conditions. However, a disconcerting discovery was the load shedding of the outby pillars as the recovery room was mined into. This behavior was not expected with a relatively narrow room that is fully supported with standing support. If this mechanism is indeed occurring, the width of the room and performance of the standing support becomes even more critical. Premature failure of the support can lead to excessive convergence on the shield line that cannot be controlled even with modern shields, resulting in instabilities that can lead to catastrophic results. Understanding the load transfer mechanics associated with the advancement of the longwall face into the pre-driven recovery room and the widening of the room to recover the longwall shields is providing valuable information for the refinement of the NIOSH Ground Reaction Curve for standing and intrinsic roof support system design.

By V. Castranova, T-M. Ong, V. Vallyathan, M. J. Keane, W. E. Wallace Jr.

"Inhalation of certain forms of silica, asbestos and some other respirable dusts can result in pulmonary fibrosis, characterized by destruction of the surfaces of alveoli and respiratory bronchioles. Fibrous thickening of the alveolar septa decreases the lung's capacity for gas exchange.Pulmonary macrophage damage by respired dust may initiate the fibrotic response.In one proposed mechanism, dust particles interact with the plasma membrane of a macrophage. This damages the cell or induces some hyperactivity of the cell, resulting in excessive release of lysosomal enzymes and reactive forms of oxygen (1). These reactive enzymes or radicals then damage the alveolar surface epithelial cells. A second mechanism has also been pro¬posed (2,3) in which dust damage to the macrophage causes the release of mediator substances which induce pulmonary fibroblast cell proliferation and increased collagen synthesis. This produces fibrous tissue in the terminal air spaces (4,5).Mineral surface interactions with plasma membrane lipoproteins have been proposed as a mechanism of lytic damage of pulmonary cells by silica dust in numerous models (6,7). The significance of dust surface proper¬ties has been further revealed in studies showing significant changes in dust induced cytotoxicity as a function of dust surface crystallinity and organic or inorganic contamination or coating of mineral surfaces (8,9). Such modification of the mineral surface might interfere with surface sites responsible for the toxicity of dusts for pulmonary macrophages, thus interrupting the early stages of the process of fibrosis.In vitro cellular assay systems using erythrocyte hemolysis or the release of macrophage cytosolic or lysosomal enzymes following dust challenge, have been used to analyze the initial mechanism of dust damage to cells. However the ability of these assays to predict the pulmonary disease producing potential of various dusts is imperfect owing to some ""false positive"" results. These assays as performed are therefore questionable models for the initial lesion in pneumoconiosis or silicosis. In particular, kaolin frequently is found to have comparable biological activity to silica quartz in these assays (10,11).Silica and kaolin have distinctly different fibrogenic potentials. Silica is highly fibrogenic, resulting in both acute and chronic silicosis (12). Some epidemiological data and animal experimentation data have indicated that long term exposure to kaolin can result in pneumoconiosis; however, kaolin is relatively benign as compared to silica (13-18). Kaolin is also of interest because it is one of the major mineral inclusions in Eastern U.S. bituminous coals. We have observed that exposing respirable sized native silica or kaolin for two hours to pulmonary macrophages results in a greater enzyme release for kaolin exposures, on a dust mass basis. Exposure of erythrocytes to the dusts also results in greater levels of hemolysis by kaolin for equal mass respirable dust doses. Therefore, these results do not correlate positively with known disease inducing potentials of the two dusts.Characterization of physical and chemical surface properties of dusts involved in occupational exposures, and characterization of the alteration of those surface properties which are likely to occur upon deposition of the dust in the lung, should improve the identification of respiratory disease hazards.Inhaled dust particles deposited in the lower respiratory tract will come in contact with pulmonary surfactant. This surfactant forms a surface film on and emulsion in the liquid hypophase coating of the alveoli and respiratory bronchioles. The primary constituent of this pulmonary surfactant is the lipid diacyl glycerophosphorylcholine, lecithin (19). Because this lipid is also a major component of cell membranes, it is possible that surfactant can interact with mineral dust to alter its Interaction with macrophages and other pulmonary cells and, thus, it"

Jan 1, 1988

By R. W. Welker

A technique was developed for sampling and analyzing airborne dusts in diesel-operated, underground, metal, and nonmetal mines. Samples were taken using personal respirable samplers, operated as area samplers, and an 11-stage cascade impactor. Real-time particle size distribution and concentration measurements were made with a quartz crystal micro-balance cascade impactor and a portable electrical aerosol analyzer. The materials characterized were minerals (by XRD), elements (by XRF), particle size distribution and concentration (gravimetrically), and organic constituents (by HPLC). The method was used to characterize dusts generated at the chute pulling operations on the main haulage level of an underground tungsten mine. Analysis showed that respirable dust concentration ranged from 0.8 to 2.3 mg/m3. It consisted of silica (3-7%); organic constituents from diesel exhaust (0.11-0.31 mg/m3 equivalent airborne concentration); and mineral dust (39-100%). The remainder was diesel exhaust particles. It was concluded that size selective sampling may be used to estimate the ratio of diesel exhaust to nondiesel dusts in the respirable fraction.

Jan 1, 1982

By Charles A. Seitz

This Bureau of Mines report describes a chromatographic method for analyzing impurities in helium that utilizes a helium carrier gas contain-ing 25 to 30 ppm Ne. An example of the effect of trace amounts of nitrogen, methane, and moisture on the detector's response is shown. The added neon in the carrier does away with irregularities of the analysis which were experienced when the carrier contained up to 3 ppm Ne. The addition of 25 to 30 ppm Ne causes a loss of sensitivity, but the re-maining sensitivity is adequate for routine analyses. The high-neon carrier allows positive and more linear responses for eight impurities: neon, hydrogen, argon, oxygen, nitrogen, methane, carbon dioxide, and ethane. Neon concentration levels of 0.02 to 125 ppm in helium carrier gases were studied. The high-neon carrier has been in successful rou-tine use in Bureau of Mines helium facilities since October 1981.

Jan 1, 1985

By Benjamin W. Haynes

This research was conducted as part of the U.S. Department of the Interior, Bureau of Mines program to recover metals, glass, and a combustible fraction from municipal solid waste (MSW). The objective of this analytical study was to determine the concentration of antimony, arsenic, and mercury in samples taken from various sampling areas in the Bureau of Mines raw refuse recycling plant and to compare these values with those for coals used in the generation of electricity. To provide the necessary analytical data, sensitive reproducible ashing-chemical digestion-atomic absorption procedures were adapted from published procedures. It was determined that antimony and mercury concentrations in the combustible fraction of MSW are approximately an order of magnitude higher than those found in coals presently used for power generation;' the arsenic concentration is similar in both fuels.

Jan 1, 1978

By D. P. Schlick

The German experience in dealing with the health hazard of respirable dust in underground mines is reported from first-hand observation in this Bureau of Mines paper. The report covers-- 1. The control of dust by water infusion, water spraying, and ventilation. 2. The sampling devices (tyndalloscope , konimeter , and BAT-I) and methods used to determine the dust concentrations in mines. 3. The systems of classifying hazardous and safe dust levels in mines. 4. The research facilities devoted to theoretical and applied work on mine dust and pneumoconiotic disease. Tile major research projects on dust and disease now underway in West Germany are outlined in an appendix.

Jan 1, 1970

By W. H. Engelmann

The electrokinetic (zeta) potentials of a charcoal granite in an aluminum chloride (AlCl3) solution and in an oleylanunonium acetate (C18H35NH3+ -OCOCH3) solution have been correlated with the specific damping values as measured by the pendulum sclerometer. This investigation shows that the pendulum specific damping attains a minimum at the isoelectric point for the charcoal granite-aluminum chloride and charcoal granite-oleylammonium acetate systems, and thus indicates that the penetration of the diamond points is a maximum at the isoelectric point.

Jan 1, 1967

By D. Harrington, W. J. Fene

For nearly 30 years the Bureau of Mines has contended that mine explosions can be prevented and has pointed out to the industry ways and means by which they could be avoided. The record of co2l-mine explosions • during the past fiscal ?Bar bears out the :Bureau1s contention, inasmuch as fewer men were killed by coal-mi~e e:xplosions in the United States during that year than in :gi_y corresponding 12 months in the history of coal mining in the United States, insofar as records are available; and more than a year has elapsed since·a major explosion (in which five or more men were killed) has occurred, this being t.1-J.e first continuous 12- month period without a major coal-mine explosion disaster in the United States in more than 60 years. The methods of preventing mine e:iiplosions are well known to experienced, well-informed persons cngnged in coal mining. Despite this knowledge, many coal-mine operutors continue to use practices and methods that they should know have resulted in countless explosions, and mine workers persist in following past procedure or in breaking safety rules and practices almost certain eventually to result in disaster. ' Virtually all explosions are the result of human failure, such as carelessness or neglect by officials or workers or others. These human failures can be corrected chiefly by ed.ucation and proper and adequate supervision and strict discipline. In some instances mine officials are ·lax, careless, poorl~• informed, and often incompetent; end in many instances miners have repulsed the introduction of known preventive methods because of sheer obstinacy, ignorance, heedlessness, or possibly fear that the operator was trying to o'bta.in some unfair adva.,.'1. tago or would neglect some other phase of accident or e,:plosion prevention. The freedom of the fiscal year 1938-39 from major coal-mine explosions ar..d frora any considera~le number of fat,JJ.i ties from minor explosions is a. matter for congratulation, but on the other hand. the occurrence of one rather bad e~losion in each of tho 3 calendar years 1937

Nov 1, 1939