Search Documents

By W. T. Millar

Graphite in the Suffern deposits near Hillburn, N. Y., consists of flakes ranging in size from fines to one-half inch in diameter. The Bureau of Mines investigated the Suffern deposits in the spring of 1943. Gneiss outcrops were examined, and five trenches excavated and sampled. The graphite is not confined to any definite zone but occurs in small, local pockets. Eleven samples were collected and combined for laboratory tests. Tests by the Bureau of Mines indicate that the graphite ore can be beneficiated by stage crushing, "skin flotation" of coarse flakes, and wet flotation of minus 10-mesh flakes. Over 90, percent of the graphite was recovered.

Jan 1, 1949

By John D. Sullivan, Alfred P. Towne

"In copper percolation-leaching plants the ore is usually crushed to a maximum size of about three-eighths inch. Ordinarily an ore is crushed as finely as feasible since the rate of extraction of copper is increased with decreasing size of particles owing to the greater surface exposed and. the shorter path required for solutions to come into contact with the minerals to be dissolved. However, greater degree of crushing also increases the amount of fines. When ores are charged into leaching vats the coarse and fine material tend to segregate, resulting in channeling of solutions and leaving the areas where fines predominate only partly leached. An improvement in the method of charging the ore into vats that would minimize the deleterious effects of the segregations of fines would increase the percentage extraction of copper.The Inspiration Consolidated Copper Co.4 recently installed classifiers to remove the primary slimes from the ore, before charging it into the leaching vats. This necessitates a separate agitation treatment for the slimes.Recent publications5 of the bureau have shown the advantages of agglomeration followed by trickle leaching to extract copper from concentrator tailings. It was shown that when equal parts of ore crushed to about 1/4-inch size and concentrator tailings were agglomerated with approximately 10 per cent of moisture, either in the form of water or leaching solution, and the mass was charred into a leaching vat the ore could be treated successfully by open-drainage trickle leaching. Even with 30 or 35 per cent of minus 200-mesh material present the ore could be leached, if it was not flooded with solution.The results obtained in agglomerating ores and slimes suggested the possible advantages to be gained by wetting the crushed ore for standard percolation-leaching plants before charging it into the vats. Wetting the ore whould make the fine material and slime cohere to the larger pieces of ore thus tend to prevent segregation when the ore is charged into the vats. The bureau, at its southwest Experiment Station and in cooperation with the Department of Mining and University of Arizona, Tucson Ariz., therefore made a study to work: out A way in which slimes could be handled in percolation leaching. The study showed that the method of charging ore into the leaching vats governed the distribution the fines and consequently the rate extraction of copper. The results of the study reported in this paper."

Feb 1, 1931

By F. C. Gregory

"Introduction.The third annual mine-rescue maneuvers of the Globe-Miami District First Aid and Mine Rescue Association were held at Globe, Ariz., on November 5 and 6, 1923. The first demonstration was held in October 1922, and the results** from that experiment, both in the practical training and the interest aroused in the apparatus men, were so much more satisfactory than those from the ordinary smoke-chamber training, that Orr Woodburn, director of the Association, decided to hold similar maneuvers at frequent intervals. The second test was held on March 21-22, 1923, in connection with the meeting of the Southwest Mining Section of the National Safety Council at Globe.Place and Organization.The recent maneuvers were held in the same mine and conducted in the same general manner as the first, and the points of interest not brought out previously are described below. By studying the accompanying map the movement of the teams can be better understood.Thirty-three apparatus men were out on the first day and thirty-two on the second day, a total of forty-three men being trained.Mr. Woodburn was aided in directing the work by his two assistants from the mine-rescue station, two local safety engineers, and an engineer from the Bureau of Mines. Local mine superintendents and the State deputy mine inspector were interested spectators."

Jan 1, 1924

By C. A. Herbert

The old fatalistic idea that industrial accidents were a necessary part of industry and that little, if anything, could be done about them has been succeeded by realization that a majority of the hazards causing these accidents were man-made and that if they could be recognized most of them could be eliminated and the accidents prevented. Recognition of these facts has brought about substantial reduction of accidents in many coal dines, as well as in other industries. Knowledge of the hazards and their elimination has been obtained largely through a study of individual accidents and the causes which led up to them. With this thought in mind tae available data on coal-mine explosions in Illinois were studied.

Jan 1, 1934

By George Quackenbos

The principal objective of this Program is the design, fabrication and testing of an Environmental System for operation in underground mines, to assess the effect of various mining systems on the contaminant levels near the mine face and within return airways. In order to determine the effect on airborne contamination in mines resulting from the development of new mining techniques, equipment and control systems, a Comprehensive Monitoring System is required to assess such contamination levels at critical and strategic locations and relate this information with ventilation parameters. The three variables to be sensed on a continuous basis are airborne dust concentration, methane concentration and ventilation air velocity. Each Monitoring Station will consist of a self-contained unit containing a power source and sensors to monitor the three above mentioned parameters. Ruggedness, reliability, ease 'of operation and intrinsic safety are important design objectives. Data gathered by each Monitoring Station will be fed to a Central Data Acquisition System by means of a portable transfer unit.

Jan 1, 1982

By Jennifer A. Slatnick

The U.S. Bureau of Mines estimated the potential availability of titanium from 39 mines and deposits in 12 market economy countries. The evaluated properties account for 76 pet of the market economy country demonstrated resources, which total 603 Mt of contained titanium dioxide (Ti02) in the minerals rutile, ilmenite, leucoxene, and anatase, and represent 95 pct of current production. Approximately 250 Mt of contained Ti02 could be economically recovered from evaluated titanium operations at January 1992 market prices. In terms of mineral concentrates, this equals approximately 19 Mt of rutile concentrate, 110 Mt of ilmenite concentrate, 47 Mt of synthetic rutile concentrate (in addition to the ilmenite), and 160 Mt of titanium slag that could be recovered. Over the past decade, the titanium minerals industry has adapted to the changing market. In the 1980's, titanium producers expanded production because of the rising demand for titanium products. Today, the titanium industry is in a state of overcapacity, and byproduct revenues, such as that from zircon, have become essential in keeping operations profitable. The industry has also witnessed a greater dependence on upgraded ilmenite products, such as titanium slag and synthetic rutile, because of the expense of rutile and the lower wastes emitted from these upgraded products. As a result of this dependence on upgraded ilmenite products, South Africa has become a leading titanium producing country and has displaced Australian production.

Jan 1, 1994

By Edmond Chin

The area encompassed by the political entities included in this study com-prises 11 million square miles or about 15 percent of the total Earth's land area. The bulk of the region is contained on the Asian continental land mass. Australia, the world's largest is-land or the world's smallest continent, alone is almost as large as the continental United States. The islands of New Zealand, New Guinea, Borneo, Sumatra, and Honshu are among the largest in the world. Collectively, they constitute a land area of 1.1 million square miles or an area about one-fourth the size of the United States. The region is noted for its great rivers. The Chang, Huang, Amur, and Mekong are respectively the fifth, sixth, eighth, and eleventh longest rivers in the world. The Ganges-Brahmaputra has created the world's largest delta, which covers 30,000 square miles. Abutting East Asia are the Sea of Japan, Dong Hai, Nan Hai, Bay of Ben-gal, and Arabian Sea. In the Southern Hemisphere, there is the Indian Ocean and the South Pacific Ocean. The Continental Shelf adjacent to the region constitutes a large proportion of the world's readily accessible shelf area. On the other hand, the Philippine and Java trenches and, further out, the Mariana Trench reach to formidable, abyssal depths, downward to 6,000 fathoms. Contrasting to this is Mount Everest, which reaches a lofty height of 29,028 feet. And then there is Xizang, whose high plateaus have been called the roof of the world.

Jan 1, 1992

By L. A. Haas

Hydrogen sulfide was decomposed to elemental sulfur in an electrical discharge. With He, N., or Ar diluents, a threshold voltage between 1 and 3 kV was required for the decomposition reaction to occur in a laboratory ozonizer. Above the threshold voltage, the HAS decomposition rate increased with increasing voltage, but the increase was more pronounced with argon diluent than with either nitrogen or helium. In common with other reactions in an electrical discharge, the B2S decomposition decreased with increasing temperature in the range of -410 to +61° C. The reaction did not appear to be rate-controlled by a solid-gas sorption step because the introduction of activated charcoal into the electrical discharge zone did not significantly affect the decomposition yield. In the presence of polymeric chlorofluoro-carbon oil, 90 pct conversion of the 3 pct H2S in helium was obtained at 14 kV, 60 Hz, a 2-mm electrode gap, and a gas-residence time greater than 1 min. Under the same experimental conditions in the absence of oil, the conversion was only about 50 pct.

Jan 1, 1973

By Thomas A. Davidson

The Bureau of Mines Helium Field Operations has developed a method for determining the helium-3 CHe) content of natural gas and mixtures eontaining 0.5% to 100% helium. The helium is preconcentrated by passing samples through anhydrone, a liquid-nitrogen-cooled chareoal trap, and a titanium absorption trap. The mass spectrometer used to analyze the samples is tuned to 3He at mle ::=; 3.016. Hydrogen deuteride (HD+) interference is minimized by the titanium absorption trap and high instrument resolution. Sample measurements are compared with identically made measurements of a gravimetrically prepared primary standard. The method has a limit of detection of 0.15 ppb with a relative deviation of 13% below the 1~ppb level. The relative deviation is less than 7% for gases eontaining over 100 ppb 3He. The helium isotope ratios of natural gases from the Bureau's Tuck-Trigg Dome Red Cave, the Bush Dome Red Cave, and the Bush Dome Brown Dolomite Formations are distinguishable from one another and from the isotope ratio of crude helium produced from the Panhandle-Hugoton Gasfield.

Jan 1, 1990

The Menominee Range of northern Michigan was a major producer of direct shipping iron ore for nearly a century. When the last underground mine on the Range ceased operation in 1978, it marked the end of an era. For since the start of mining in the early 1880's the district has gone through a Lull cycle from the start-up of mining through close-down. During this period over 200 million long tons of iron ore were produced and shipped from nearly 100 mining operations. This development and production spanned the time from when the United States advanced from an essentially rural-agriculatural society through the industrial revolution and into the beginnings of the computer and space age. There are many lessons that can be learned from such a rich history. This report attempts to provide ouch a lesson. Through the use of case histories, deficiencies in past mining practices and mine closure procedures that have resulted in current mine related problems are documented. These problems -an be grouped into three areas; 1) subsidence 2) hydrological or drainage problems and 3) problems related to inadequate mine shaft sealing and capping practices.

Jan 1, 1983

By J. K. Whyatt, B. G. White

A comprehensive survey of mine seismicity and rock bursting during development of two sublevels at the Lucky Friday Mine, Mullan, ID, USA, was conducted to better define rock failure mechanisms and sources of ground control hazards. Survey data included rock burst damage reports, seismic event locations and magnitudes and, for the most energetic events, first-motion information. Several subsets of this database, including large seismic events, rock bursts, and microseismic activity near the face, were analyzed. Elements of the large-event and rock burst data sets were nearly independent. That is, there was no relationship between the risk posed by a seismic event and its energy, although such a relationship is well established for the mine as a whole. All data sets showed that certain geologic features appear to control the spatial distribution of events and the spatial distribution of rock burst risk. The data also suggest that, within the scope of this study. the greatest risk of injury occurs when a pocket of heightened rock burst risk is first encountered and that this risk is controlled when miners adapt their practices to these conditions. Recognition of the role of particular geologic features in the spatial distribution of rock burst hazards provides an opportunity for anticipating, rather than only reacting to, a changing level of rock burst hazard- However, much work will he required to make good on this promise.

By John H. Johnson

Diesel tailpipe CO, C02, NO, and N02 concentrations by the Emissions Measurement Apparatus (EMA) were found to compare satisfactorily with simultaneous concentrations by instruments in the MSHA engine certification laboratory in Bruceton, Pa. The EMA was then applied to the measurement of LHD vehicle diesel tailpipe gases and smoke opacity in the White Pine and Brushy Creek Mines. A general experimental approach was developed by which instruments could be compared for the measurement of diesel exhaust pollutant concentrations in the 1/2 to 5TLV range. The concentrations are changed by varying engine speed, dynamometer load, and the portion of the exhaust which enters the dilution tunnel. Dräger detector tube diluted exhaust CO, CO2, NO, and NO2 measurements were compared with simultaneously taken portable instrument measurements. Diesel exhaust interference inaccuracies were separated from inaccuracies due to detector tube calibration by comparing the instrument readings with both actual detector tube readings and detector tube readings corrected by recalibration of the detector tubes alongside NBS traceable calibration gases. The detector tubes' accuracy was found to be only slightly affected by diesel exhaust interferences and it was concluded that most measure within certification limits established by the National Institute for Occupational Safety and Health. The effects of 2 exhaust system configurations on the pollutant concentrations in a dead-end heading were studied. Both of the configurations exhausted the gases near the roof, directing them toward the crosscut, and both improved the stratification of the air in the heading, due to the bouyancy of the hot exhaust gases. One of the configurations was a pair of Fume Diluters which diluted the exhaust with air by a 10:1 ratio, and the second system was simply a pair of exhaust pipes, bent to direct the exhaust similarly to the fume dilutors. By redirecting the exhaust, the concentration of C02 measured on the LHD vehicle was reduced by as much as 507, in dead-end headings up to 200 ft long. The Fume Diluters showed no improvement over the simple redesign of the exhaust system.

Jan 1, 1980

By E. D. Gardner

This is one of a series of paper's being published by the Bureau of Mines on placer mining; it is written as a supplement to Information Circular 6788, "Placer Mining in the Western United States, Part III", by E. D. Gardner and C. H. Johnson which was published in February 1935. Since Information Circular 6788 was written (1933), considerable advance has been made in the technique of mining placer gravels with power shovels and draglines. Although new washing plants continue to be built in accordance with untried designs the trend of new installations is toward proved equipment. A substantial number of plants are now being operated successfully (1937).

Jan 1, 1938

To provide cooler air to miners working in hot areas of mines, particularly new deep hardrock mines. Approach Air supplied to hot working areas of mines is cooled by passing it through a series of water sprays. How It Works Water nozzles mounted inside a section of ventilation tubing release cooling sprays of water into the air being blown through the tube. The prototype of the water spray cooler consists of six evenly spaced water sprays located inside a 10-ft. long section of 16-inch-diameter fiberglass ventilation tubing. See diagram. This section of rigid tubing is installed into one of the positive pressure ventilation tubing lines that conduct fresh air into working stopes. The intake manifold to the six water sprays is connected to the mine?s cool water line, and the water valve on the manifold is opened. Warm ventilation air being supplied to the stope passes through the water sprays, and is cooled by the lower temperature water.

Jan 1, 1979

In the USA, the National Institute for Occupational Safety and Health (NIOSH) does a lot of work and has provided news of interesting new developments. Marcia L. Harris describes an ?Explosibility Meter: ?In underground mines, coal dust explosions are prevented by the addition of rock dust sufficient to render the coal dust inert. Federal [US] regulations require 65% and 80% incombustible content in samples taken in intake airways and return airways, respectively, assuming a nominal coal dust size of 20% minus 200 mesh. The Coal Dust Explosibility Meter (CDEM), a hand-held instrument developed by NIOSH uses optical reflectance to measure the explosibility of a rock dust and coal dust mixture.? The CDEM is now commercially available. It provides real-time results during rock dust surveys instead of waiting weeks for laboratory results1. ?With real-time results, the potential for a disaster can be mitigated immediately. The CDEM displays the percent incombustible content as well as a colour indicating the relative explosibility of the coal and rock dust mixture. A red read-out indicates that more incombustible material is required to inert the coal and rock dust sample, while a green read-out indicates that the dust sample is sufficiently inert. When the mixture is marginally explosible, a yellow read-out is indicated. The red-yellow-green output depends upon the particle size distribution of the rock and coal dust mixture with the finer size fraction being more explosible.?

Jan 1, 2008

By Charles L. Kimbell

Some comment on data availability must be an integral part of a study such as this. For many years, the centrally planned economy nations of the world regarded as state secrets much of their mineral commodity production information, as well as a considerable body of the foreign trade information on these commodities, and virtually all reporting on their consumption. Within the past 5 years, this pattern has undergone some evolution, and although these countries still fall short of market economy countries in their willingness to publish, there has been measurable improvement. Fit, China, and then subsequently the former CMEA member countries of Eastern Europe have released in print an increasing amount of information in organized, coherent formats, although in a number of cases it is not clear that the information provided is in perfect definitional accord with market economy country practices. Thus, these recently available statistics must be carefully studied to ensure that they are provided in terms of conventional market economy definitions. At the same time that heretofore unpublished information is becoming available for the centrally planned (or formally centrally planned) economy countries, there has been a slow but steady disquieting erosion of availability of production, trade, and consumption data for market economy countries. There are evident reasons for some of these losses in information. The foremost of these relates to corporate mergers. As the number of producing or consuming firms of a given commodity in a given political jurisdiction declines, it is increasingly difficult for government agencies to protect proprietary company data. In past years, this protection was afforded by aggregating data for the several companies operating in the area, but as the number of operators diminishes this is no longer always possible. Hopefully, given this situation, companies will at least authorize release of data after a period of time, when its publication will not provide competitors with unfair access, but will make possible longer term studies.

Jan 1, 1992

By Walter W. Fisher

A study of copper cementation on iron was initiated to determine the effect that deposited copper has upon subsequent cementation. A microscopic investigation of cementation on an iron surface showed that cupric ion precipitates predominately on a growing copper deposit attached to the iron surface. A kinetic study of the cementation process in a revolving drum showed that the cementation rate is enhanced by the copper deposit attached to the iron surface and by the discrete copper particles of a cement copper slurry. The kinetic study also indicated that the character of the deposit is affected by the major anion in the solution. The cementation process is visualized to occur as a series of electrochemical cells in which cupric ion precipitates on copper dendrites attached to the iron surface.

Jan 1, 1973

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the' danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By Etienne Audibert

No satisfactory theory has yet been advanced to explain what takes place when an explosive is fired in a mixture of firedamp and air. The only means of measuring the danger is to fire the explosive into the gas mixture and note the effect, but the conditions of firing must be chosen carefully. This report is presented in the hope that it will assist in determining what method to use. The experiments have been designed to show the effect of the principal factors involved in the conditions of firing, and the results give information that seems to have some value.

Jan 1, 1940

By J. M. Kuchta

Bench-scale test methods were developed by the Bureau of Mines for use by the Department of Transportation in the classification of solid and liquid oxidizers. A burning rate test is recommended for evaluating the fire hazard of solid inorganic oxidizers when mixed with a red oak sawdust as the reference combustible. A spontaneous ignition test is proposed for evaluating liquid and solid inorganic oxidizers which may decompose violently or ignite spontaneously when unmixed or mixed with the wood sawdust under unconfined conditions. Test results are compared for various representative oxidizers and a classification system is proposed for use in the government transportation regulations.

Jan 1, 1972