Search Documents

By John S. Berber

Bureau of Mines research on the production of phthalic anhydride by vapor phase oxidation of hydrocarbons began at Morgantown, W. Va., in October 1960. For these preliminary studies, a known solution containing naphthalene and 1-methylnaphthalene was used. In another series of tests, pure naphthalene was dissolved in different solvents. A series of investigations was conducted with the neutral oil fraction (210° to 270° C) of a low-temperature tar obtained from the Texas Power and Light Company's low-temperature carbonization unit. The neutral oil fraction was first dealkylated, and then the product was distilled into 210° to 250° C and 250° to 270° C fractions. These two fractions were then subjected to catalytic vapor phase oxidation. Although a number of catalysts was tested, most of the experiments were made using 9 percent vanadium pentoxide on inert alumina. The activity of this catalyst did not decrease after 162 hours at 1,030° F. Studies were conducted over a temperature range from 610° to 1,180° F. An operating temperature of 1,030° F yielded 47.50 percent of phthalic anhydride from a synthetic mixture of naphthalene and 1-methylnaphthalene. The highest yield (84.40 percent phthalic anhydride) was obtained with naphthalene dissolved in toluene and also with naphthalene dissolved in methyl ethyl ketone. With a 210° to 250° C fraction the highest yield of phthalic anhydride obtained was 12.32 percent at a temperature of 900° F, and, with a 250° to 270° C fraction, it was 15.80 percent at a temperature of 875° F.

Jan 1, 1963

By Richard L. Rains

In 1984 and 1985, at the request of the Bureau of Land Management, the U.S. Bureau of Mines studied part of the 162,887-acre Mormon Mountains Wilderness Study Area (NV-050-161) in order to evaluate its identified mineral resources. The study area is located in Lincoln County, NV, about 60 miles northeast of Las Vegas. The study area had no mines or mining claims in 1985, and no mineral resources were identified within the study area, or at the Whitmore mine or Iron Blossom prospect near the study area. The alluvial fans around the southern boundary are staked with about 450 placer claims. Chemical analyses of samples indicate that some limestone in the study area is suitable for manufacturing cement or for agricultural purposes but the limestone is distant from markets and therefore not economic in the foreseeable future. The study area is blanketed with oil and gas leases, but no known productive horizons were identified.

Jan 1, 1986

By R. V. Ramani, V. T. Burgos, J. A. McClay

General The underground mining environment has traditionally been hostile and as early mines were developed, coal seams with particularly difficult natural conditions were bypassed in favor of those more easily exploited. Barring the discovery of new and novel sources of energy, the depletion of petroleum and natural gas reserves will eventually force the United States back to the use of coal as its primary energy source. Figure 1 illustrates the trend away from coal which has taken place over the past half century. Today, the demand for coal requires a re-evaluation of all coal seams to meet the needs of the energy market. Difficult mining conditions may result in an increase in the consumption of roof control materials, require greater investment in pumping and ventilation systems, and increase the need for in-depth engineering of far greater safety in production plans. They may also cause delays in mine development and curtail production, all of which combine to drive up the unit production cost. It is reasonable to expect that conditions will continue to deteriorate as current reserves are depleted, thus bringing this factor into greater prominence in the future. For several years now, it has become apparent that in addition to economic objectives, coal companies must set and achieve several concomitant objectives to accomodate society's interest in the conservation of natural resources. Government action to meet this interest has taken the form of two categories of Federal legislation, environmental protection and employee health and safety. The effects of both of these have not been fully evaluated with respect to the total economic picture, although preliminary evidence indicates that an immediate increase in

Jan 1, 1975

By Arnold O. Tanner

The domestic mining industry continued to be strengthened and revitalized in 1989. The healthy conditions and the industry comeback that began in 1987 continued to spread and became more established for many commodities. Relatively comfortable and stable commodity prices, still found predominantly in the metals sector, reinforced other operational factors in bringing vitality to the mining and mineral processing industries. New streamlined business practices, mine and plant modernizations, and the progressive use of new technologies successfully helped lower operating costs and increase efficiency during the past 5 to 7 years. An element common to these three factors of industry renewal and growth was the ever-increasing infusion of and growing dependence on constantly advancing computer technology applications. This trend of increasing computerization was occurring throughout the mining and mineral processing business while it similarly was in most facets of modern business and culture. Some commodities and companies still struggled to outlive sluggish prices and other unstable market conditions or to modernize their businesses, but increases in productivity and profits were more common. A trend toward increased mechanical excavation in nonsoil materials was beginning to surface as a substitute for standard cyclic mine development techniques, such as drill-and-blast and surface shovel-and-truck routines. More continuous mechanical excavation offered the potential for increased production, fewer people at the working face, better ground control, and generally improved safety. The main limitation was rock hardness. The construction industry had already recognized the benefits of tunnel-boring machines for long underground drives and mechanical planers for pavement removal. The Colorado School of Mines held a short course during the year entitled, "Mechanical Excavation Techniques in Mine Development and Production,'" which was at-tended by nearly 100 engineers from 12 countries. The consensus of attendees was that for the most efficient use of these machines and techniques, new mining plans needed to be developed beyond the simple adaptation of those excavators to existing mine plans.1

Jan 1, 1991

By Donald O. Capstick

A mineral survey of a 13,525-acre portion of the 21,875-acre Owyhee Canyon Wilderness Study Area in northern Nevada was conducted by the U.S. Bureau of Mines in 1984. Two samples from sand and gravel deposits in the study area contained minor placer gold typical of the Owyhee River area. The gold-bearing gravels are too low grade or of insufficient volume to support commercial placer mining operations. The sand and gravel deposits might have minor local construction uses.

Jan 1, 1986

By Wing G. Agnew, Albert E. Long

"SUMMARY AND CONCLUSIONSTests conducted at Mount Weather indicate that clear water is the best bit coolant and cuttings-removal medium for diamond drilling. All of the mediums tested did show that drilling speed increased when drilling with the faster feed ratios (greatest pressure on the bits). In no case, how¬ever, did the increased drilling speed amount to over 16 percent, and even in a long hole the slight increase in drilling speed would be more than offset by the extra time consumed in setting up.Bit wear was excessive when lubricating agents were used, the most footage per bit was obtained when drilling with clear water in the normal manner, and the next best footage was obtained when drilling with circulated water containing no lubricating agent. The diamonds showed little or no wear in any of the bits, and all bits cut well throughout the tests. They were only taken out of service when erosion of the cast metal had progressed to the point where the diamonds were about to roll out. The lubricating agents evidently hold some of the cuttings in suspension, which in turn help to cut the rock but also wear the metal of the bit.No hard-matrix bits were tested, and it is possible that one or more of the lubricating agents might increase the efficiency of such a bit by keeping it sharp and doing away with the necessity of sharpening by sand blasting. Some tests are planned with hard-matrix-type bits and the same lubricating agents used in the tests under discussion, but it is realized that any drilling advantage gained by the bits sharpening themselves may but at least partly offset by excessive wear of the Pump parts."

Jan 1, 1945

By Alan Mayton, N. Kumar Kittusamy, Christopher Jobes, Farid Amirouche

Industrial equipment exposes individuals to whole-body vibration (WBV) and mechanical shock. This exposure can negatively impact their health, safety, comfort, and working efficiency and performance. Accordingly, proper seat design is an important consideration in reducing the adverse effects of WBV exposure to vehicle operators. Since the human body is sensitive to low frequency WBV, ride quality is a basic and important element of good seat design. When designing a suitable seat, it is essential to understand vibration exposure environment of workers and how well they can tolerate this environment [1]. This is particularly true in the mining industry. Mayton et al. [2] reported on a low-coal shuttle car seat design that underwent limited, yet successful underground mine trials. Building on this work, a follow-up study compared NIOSH and existing seat designs on low- and mid-coal seam shuttle cars. The NIOSH seat designs included viscoelastic foam, which has properties similar to those found in a mechanical spring/damper suspension system. The seats also included an adjustable lumbar support and a fore-aft seat adjustment. The NIOSH seat designs contrast with the existing seat design, which have little or no lumbar support and include inexpensive foam padding of the type commonly used in furniture. This paper will focus on the seat designs for the mid-coal seam shuttle car and compare subjective comfort data collected from five vehicle operators with ISO 2631 – based reduced comfort boundary (RCB) analysis of recorded vibration levels. Methods Experimental data were collected using three different tools: triaxial accelerometers, pre-amplifiers, and filters connected to a data recorder; a visual analog scale (VAS); and a short questionnaire. Researchers recorded quantitative or objective vehicle vibration data to determine the input and output acceleration at the operator cab floor and operator seat interface. Qualitative or subjective data, collected with the VAS, allowed researchers to obtain the operators’ immediate impressions of shock, vibration, and discomfort levels for the vehicle ride on each of the seat designs. Each shuttle car operator made six round trips with the vehicle each seat. The shuttle car operator marked the VAS on the first, third, and sixth round trip of the trials for each seat. A round trip consisted of traveling to the coal face with no load and returning to the load discharge location with a full load of coal. Results Total overall average ratings for the five vehicle operators of the mid-coal seam shuttle car, showed that operators sensed from 45 to 87% less discomfort with NIOSH seat designs compared to the existing seat design. Using a 95% CI, researchers computed a strong positive correlation for discomfort. Figure 1 illustrates the RCB analysis method for one of two NIOSH seat designs.

Jan 6, 2006

By F. Sillers, R. T. C. Rasmussen

"INTRODUCTION This is the third report of investigations by the Bureau of Mines in cooperation with industry to establish the value of electrolytic manganese in the manufacture of ferrous and nonferrous alloys. The manganese was produced by the Bureau at its Boulder City pilot plant from domestic ores and by the process developed by it. 4/ The work was done under the direction of R.S. Dean, assistant director, Bureau of Mines, and R. G. Knickerbocker, chief, metallurgical branch. The first report dealt with the use of electrolytic manganese in the manufacture of stainless steels 5/ and the second with its use in acid electric or open-hearth low- and medium-carbon steel castings. 6/The present report treats of the use of electrolytic manganese in the manufacture of low—carbon rimmed and killed steels. A résumé of these three investigations and two others appeared in the magazine STEEL. 7/ Further reports will be published as tests are completed at some 70 industrial plants. All tests were made on full—scale heats or melts, and the resultant product was processed and used commercially."

Jul 1, 1945

By Kathleen M. Kowalski, Audrey Podlesny

The Maslach Burnout Inventory (MBI) was administered and scored for 154 Mine Safety and Health Administration (MSHA), U.S. Department of Labor, employees who serve as accident investigators for serious accidents and fatalities as part of their job duties. The subjects responded anonymously during a workshop on stress. The subjects consisted of randomly selected individuals, representative of locations across the country and representative of all mining commodities: coal, metal, nonmetal, stone, and sand and gravel. The Maslach Burnout Inventory assesses three aspects of experienced burnout: emotional exhaustion, depersonalization, and reduced personal accomplishments. The average results of the scores for each of the three subscales fell in the moderate range for the study group of MSHA accident investigators. The scores within the moderate range show that the subject population was at the lower end of the range for emotional exhaustion and depersonalization, tending toward a lower burnout risk, while the group evidenced a lower sense of personal accomplishment in their jobs, indicating a higher risk for burnout. It is concluded that overall this group is at moderate risk for burnout, and the authors recommend follow-up with this population.

By H. L. Riley

Cleaning and handling of fine coal are generally conceded to be more difficult problems than preparation of the coarser sizes. Increased mechanization in the coal-mining industry has, in general, resulted in an increased percentage of the fine sizes in the total coal mined. If the coal fines are cleaned by wet methods, the minus-1/16-inch square-mesh particles cause most of the sludge and slurry problems encountered in preparing wet coal. Equipment that separates coal from refuse on the basis of specific gravity is not efficient on sizes that, because of their fineness, do not follow the same laws of hindered settling as the larger particles. Probably the best solution of fine-coal cleaning problems is to use other methods, such as flotation, that utilize other physical characteristics than those determining hindered-settling ratios. Regarding the type of flotation known as the Elmore vacuum-flotation process there has been a scarcity of data and information available in this country. An investigation has therefore been made to obtain additional date and information on this process under laboratory conditions. During this investigation an effort has been made to evaluate the relative efficiencies of vacuum and mechanical laboratory froth flotation cells. The investigation included float-and-sink, screen-sizing, and flotation tests on 2 different samples of 14-mesh to 0 raw coal and an a sample of slurry from the settling-tank overflow of a typical washer. One raw-coal sample was obtained from the American bed and represented a type of coal that is relatively easy to clean. The other raw-coal sample was from the Mary lee bed and represented a type considered difficult to clean.

Jan 1, 1954

By J. H. Nixon

A three phase program evaluated commercial proximity warning devices, developed and designed a microprocessor-based electrostatic field measurement instrument, and utilized this instrument to investigate the electro-static fields about power lines. The Phase I program consisted of test and evaluation of these commercially available proximity devices. The evaluation results were reported in the Phase I report entitlted "Evaluation of Proximity Warning Devices II dated 22 February 1980. The Phase II program resulted in the design and development of a microprocessor-based Distributed Sensor A.C. Electrometer which measures the electrostatic field present at 17 discrete locations along a crane boom. Operator control of the measurement system allows simultaneous electric field measurements from 17 probes, print out of the electric fields measured, and data archiving on magnetic tape for post measurement analysis. Under the Phase III program, electro-static fields around a crane boom were measured by the instrument at 17 high voltage power lines of various voltages and geometries. The electric field data was processed and plotted versus boom distance from the power line. Analysis of the electric field data indicate that the distances at which a single sensor alarm will activate, vary by a factory of 3 to 1. This is due primarily to variations in boom orientation. The results also indicate that in the case of multiple power lines, a single electrostatic field sensor cannot reliably be used to determine the distance from a power line.

Jan 1, 1982

By Wils L. Cooley

The report covers tests and criteria for the establishment of safe grounding systems for coal mines. The work deals primarily with under-ground coal mines, but much is applicable to surface mines as well. Included is an extensive guide to grounding and bonding procedures for mine surface substations. Xit-Rods are evaluated and shown to deviate from manufacturer's claims. An analysis shows that very long cables are difficult to monitor using audio frequency ground-check techniques. A method is developed to detect failing cable splices without removing the cable from service. Simulation and measurement are compared for a technique to detect bad rail bonds, and an assessment is made of grounding techniques for dc face equipment.

Jan 1, 1979

By W. N. Marchant

[The citrate process for flue gas desulfurization (FGD) is a product of continuing research by the U.S. Bureau of Mines to meet the goal of minimizing the objectionable effects of minerals industry operations upon the environment. The reduction of SO2, in solution by H2S to produce elemental sulfur by the citrate process is extremely complex and results in solutions that contain at least nine different sulfur species. Process solution analysis is essential to a clear understanding of process chemistry and its safe, efficient operation. The various, chemical species, the approximate ranges of their concentrations in citrate process solutions, and the analytical methods evolved to determine them are hydrogen sulfide (~0M to 0.06M) by specific ion electrode, polysulfides (unknown) by ultraviolet (UV) spectrophotometry, elemental sulfur (~0M to -0.001M dissolved, ~0M to ~0.1M suspended) by W spectrophotometry, thiosulfatc (~0M to ~0.25M) by iodometry or high performance liquid chromatography (HPLC), polythionates (~0M to ~0.01M) by thin layer chrornatogrphy (TLC), dithionite (searched for but~ not detected in process solutions) by polarography or TLC, bisulfite (~0M to 0.2M) by iodometry, sulfate (~0M to 1M) by a Bureau-developed gravimetric procedure, citric acid (-GM to 0.5M) by titration or visible colorimetry, glycolic acid (~0M to 1N) by HPLC, sodium (~1.5M) by flame photo¬metry, and chloride by argentometric titration.]

Jan 1, 1980

By Kim M. Cornelius

Musculoskeletal injury is a term used to describe a wide range of soft tissue disorders which affect the nerves, tendons, and muscles. Common examples include lower back pain, tendonitis, and carpal tunnel syndrome. The majority of these injuries are not the result of sudden mishaps, but usually develop gradually from repeated wear and tear. Symptoms may first appear after weeks, months, or even years. Symptoms may result from many types of activities, performed at work or at home, and it is often difficult to attribute a single event. In fact, it is more common to identify the factors which may have contributed to the development of the condition. The terms repetitive strain injuries or cumulative trauma disorders (CTDs) have been commonly used to refer to disorders that have occurred due to work related activities (Putz-Anderson, 1988; Fraser, 1989). Three main risk factors contribute to CTDs: force, repetition, and awkward postures. Any one or combination of these may contribute to the development of CTDs. Therefore, the design of equipment in conjunction with the required tasks should attempt to reduce these risk factors. Examining the layout of the work area to help identify tasks which may contribute to cumulative trauma is necessary. The following list(Putz-Anderson, 1988), describes ergonomic concerns that, overall, should be minimized at the work area:

Jan 1, 1997

By d&apos, Kathleen J. Amico

This summary appears in Minerals Year-book volumes I and III, which cover mineral production in the United States, its island possessions, the Canal Zone, and the Commonwealth of Puerto Rico, as well as the principal minerals imported into and exported from the United States. The several commodity and area chapters contain further details on production. A summary table comparing world and U.S. mineral production also is included. Mineral production may be measured at any of several stages of extraction and processing. The stage of measurement used in the chapter is normally what is termed "mine output." It usually refers to minerals in the form in which they are first extracted from the ground, but customarily includes for some minerals the product of auxiliary processing operations at or near mines.

Jan 1, 1966

By Y. L. Su

Deterministic and stochastic simulation were combined to develop a computer model of an open pit mining system using bucket wheel excavators and related materials handling equipment. The model is closed and dynamic in the sense that information is fed back to control activities at various levels and reservoirs. The results of interaction between unit operations in one time interval determines overall system behavior for the next interval. Equipment performance curves and system profile characteristics rather than time studies are applied to determine the operation of each activity at any time period. For that part of system where performance is dictated by a random variable~ subjective probabilities are employed. Two stages of research were considered to formulate this model. Stage one involved the formulation of equipment sub-assemblies for the sequence of equipment moves along with related assignments and routines for information retrieval. The second stage of research combined all sub-assemblies into an integrated open pit mining simulator. The model is not tailored for any specific open pit operation but is readily adaptable to any system of surface mining including operations having a high degree of complexity. Questions answered by the model include: 1) system design and selection of equipment for a new mining operation; 2) analysis of existing operations for possible changes, additions or general

Jan 1, 1971

By Stephen C. Tadolini, Yunqing Zhang, Thomas M. Barczak

Standing crib supports have been applied in underground mining programs to resist large roof movements and sustain high-loads. The strength and deformation capability of these systems has been documented under both laboratory and field conditions. The parameter that has not been examined and is not well understood is the effect that a crib or other types of standing support has on the primary and secondary bolting systems. A crib support system with low system stiffness may allow large amounts of closure and deformation and cause the bolting systems to yield or even fail. Conversely, cribs or standing support that are too stiff may experience brittle or buckling failures, negating the advantage of the intrinsic supports previously installed. Utilizing a combination of field measurements and 3-dimensional finite element modeling techniques, the relationship between system stiffness and the subsequent performance of the installed bolting system is evaluated. Additionally, a simple method for calculating the combined system stiffness for standing supports, when using materials with different strengths such as steel, concrete, wood, etc., is presented.

By Donald O. Capstick

A mineral survey of the approximately 144,000-acre Borah Peak study area was conducted by the U.S. Bureau of Mines in 1985 at the request of the U.S. Forest Service. The area studied included the Borah Peak RARE II roadless areas (No. 14210, 119,864 acres of land recommended for wilderness designation; and No. X4210, 18,440 acres of land recommended as non-wilderness) and other contiguous Forest Service administered land. The study area is in Challis National Forest in southeast Idaho about 30 miles south-southeast of Challis, ID. Burnt Creek, a conterminous study area to the northeast, on lands administered by the U.S. Bureau of Land Managment, was examined concurrently. Dolomite and limestone inferred reserve bases exceed 1 billion tons each within the Borah Peak study area. The material is widespread and of high quality. Extensive sampling and more detailed mapping are required to better define the resources; however, ample dolomite and limestone occur nearby, outside the study area. Dolomite is the main constituent of several geologic formations within the study area. Sample analyses indicate that the more than 1,000-ft-thick Jefferson Formation dolomite is the most pure and is equivalent to material being mined at a dolomite-to-magnesium processing plant near Addy, WA. Analyses from limestone-bearing formations underlying much of the study area indicate that large quantities of the limestone may be suitable for a variety of uses.

Jan 1, 1987

By W. R. Crane

Subsidence and ground movement are phenomena common to and attendant upon practically all large-scale mining operations, and under certain conditions may occur in all workings, large and small. The interpretation of the cause of failure in rock masses involves a study of the nature of plants of weakness common to all rocks. The dominating planes of weakness can readily be determined by observation in any given locality, and in order of importance in the study of subsidence are (1) faulting planes, (2) bedding planes, (3) joint planes, and (4) other prominent planes of weakness such as thrust and shear planes and contacts. This report has mainly to do with the third item, joint planes, and is a preliminary statement which t to be followed by a more complete report in bulletin form.

Jan 1, 1931

This report includes a short history of uranium and its uses, mineralogy of common uranium minerals, and information on the use of electronic prospecting equipment and tests for detecting the presence of uranium. Details are given on geologically favorable areas and formations and practical methods of prospecting. Some information is given on the staking of claims, what lands are open to prospecting, and methods of securing mining rights. A forecast of the economic outlook for uranium is included. Appendixes give sources of additional information and a list of libraries where unclassified Atomic Energy Commission reports may be consulted. Because the increasing use of uranium by industry has revived interest in prospecting and exploration for this element, the Bureau of Mines has issued this report, which brings up to date and expands the subject matter of a hand- book on uranium exploration and production published in 1956.l

Jan 1, 1968